Hoverboard motherboard hack how to hack Hover board motherboard Firmware STM32 BLDC motor cart STM
ฝัง
- เผยแพร่เมื่อ 24 ก.ย. 2024
- hover-board motherboard firmware procedure how to make a hoverboard cart with BLDC Motor
Please subscribe
Thanks
soon on github my own library
github.com/rob...
hacking hoverboard wii
hoverboard use as your trolly cart
how to use Stm8 link utility
hoverboard speed control by Potentiometer meter
make your own control control your robot
you can get the hoverboard firmware
github.com/p-h...
stm8 V2 link bldc motor firmware hoverboard .otherboard
my an other experiment you will enjoy 😉
• Arduino relays
hover board firmware
hoverboard trolley
remote controlled hover board
problem solved for stm32 not found
I make it very easy and each step is very clear even for beginners please subscribe my channel not hidden part
ST Link V2 solution
stm32 programing
stm8 programing
ST Link V2 Firmware problem Solved
Hoverboard Steering
Hoverboard Speed control
please check other video Arduino crane experment thanks enjoy 😉
• Arduino relays
2X tilt sensors for each side can be mounted on top of eachother, cables lengthened and can be mounted anywhere on the Trike/Kart on a pivot and angle can be changed via regular throttle cable to tilt forward.... break cable can make tilt backwards for breaking or reverse... then no hacking will be needed to the board.
Have you seen that work well anytime?
That's an interesting idea. Diffently gonna try that :)
Well-done for effort and well explained, it is really very useful information
It's all about technology things which I don't get ,but do get my thumbs up for the job done
nice work
Very nicely explained 👍
Yesterday i destroyed one for parts i will not sugest people to use them they can backflip from that hooverboard
Huge thanks for the video! One general question, sir. Can I in theory use this motherboard to make a force feedback steering wheel for simulator? Usually, people use motor, but they use some other bldc controller and arduino leonardo. Can this hoverboard motherboard handle all of that?
Yes possible it is other software but use HAL sensors and make connections for potentiometet
Where did you connect the potenciometers to ??
Rx and tx pins on left wheel ?
Or Rx on the left wheel and Rx on the right wheel? Thanks
Ok next week In other video I will
what type of potentiometer you use. what value? ,Thanks
Thanks for this wonderful video. I'm having trouble with the wiring etc. The battery wires attached to the board is cut off. When I try to attach it to the battery it sparks. I tested the battery with another board and that works fine. Can you gimme some tips? Also is it possible to have a chat with you? I need some more direction. Thanks in advance
Ok i will check it
wow great engineer sir
Dear Sir
I have 2 question please
1 ) Can we still reset to the normal setting program ( Orignal program ) ?
2 ) Can we still charging battery by adapter normaly ?
thanks
Yes you can charge battery
But original firmware required is avail able on github
@@MKRCLabs thank you so much 😍😍😍
Hello Thank you very much for the video, I am Vietnamese and would like to learn to repair balance bikes.I don't know if you can help me to repair the electric balance car circuit?
What is problem in cat
Awesome 👍👍👍👍👍
Thanks 🤗
Do you think we can use the motor controllers already existing on the hoverboard board? To bypass the hoverboard uC brain? Thanks.
Yes we can check my video hoverboard motherboard fitmware
Very good
Thanks
Good
Hi, just curious I have a different kind of hoverboard that comes with two motherboard for each wheel instead of one single big one like yours. Will I be able to do the same step as what you did or I will need to find new firmware for these different motherboards? thank you in advance!
Different firmware
Ok
Hi , I have the same model with the two motherboards. Did you find the "different" firmware ? or you did any progress?
Thanks so much 🍓🍓🍓
Good job!
Great
Thanks for sharing ideas
Can you control the Hoverboard using the Arduino joystick
yes
What does each wire colour represent on for the potentiometer?
1st Earth 2nd to board ( middle) 3rd +3.3 v
Nyc
What is the point of the firmware? Why can a receiver just tell the circuit board to go forward and backwards?
Nice
can we control the motor separately by potentiometer?
It is possible if you use BMD ZS-X11B you need two controler with hover board controler I try it give problem during reverse/forward
What is the size of the potentiometer you are using?
10kohm
I have an issue while connecting ,though my St link upgrades but when my ST link upgrade ends , it says " ST link device lost when exiting upgrade mode "
Nice 👍
Best
Hi! Is it work with normal ebike throttle ( with hall sensor ) ?
Yes but only three phase bldc motor
Yes works but only three phase bldc motor please confirm the voltages too
@@MKRCLabs Thank you!
Gud
Can you advise. I am using stm32 cube programmer and st link V2 and upgraded the firmware connected, disconnected st link however, couldent connect
Reseting required after upgrade or first connection thats why connec and reconnect
@@MKRCLabsI did disconnected and reconnected the st link after firmware upgraded, still no connection
Stm32 original devolvement board or bluepill ebay
I will try on my hoverboard with different st link
Install zadig usb driver it will solve you problem
Is possible to connect rc receiver instead of potentiometers?
Possible
@@MKRCLabs thanks, got all done already. As soon as get messages, started dogging all around and found how to do it.
Can a hoverboard that was using 14 cell, 24V battery use 20 cell, 36V battery?
Sir my hoverboard red light is blinking 2time how to solv it?
I am so thankful to you if you guide me
Hi
I take of the two infrared sensores to put the motors running automaticly, but just one running, how can i put the other running too???
Possible
Nice a.h.g
Delicious and tasty
Nice great great
Hello friend, I would like to know what I have to modify in the file to remove the speed limit
Hey i want to ask you i did with remote but wheels always spinning when i turn on remote control but dont do enything only on what could be the problem? Pss: i have to remove and insert again battery to stop it and turn off remote. Thanks if you could help 😊
Use different hex file from github
@@MKRCLabs nice thanks but could you help how to turn left or right? back or forword it gose but left and right not😊
Sir ji min pakistan sy hun ap ki awaz sy lag raha hy ap pakistani ho help me sir
Yes
@@MKRCLabs ap ki help chahy
i really need help i have 2 st-link v2 wen i connected to pc the pc foundet without problem but the STM32CubeProgrammer and STM32 ST-LINK Utility didnot found the st-link v2 what ido?????
Update v link 2 software
@@MKRCLabs how i update if the software didno found the stm32
First update st link
2nd after connection disconnect and reconnect this is solution i secially explain this part in video
If still problem use other way create hex file and try with st link v2 no need st cube programer
Hi
I m
Haroon from Pakistan
You from we’re plz?
Can you give me Whatssapp number please
I want talk to you
Yes friend
Thank for reply
✔️✔️
How to brake in full speed? Thanks
Just rotate potentiometer or change rotation anticlockwise or switch off
Thanks for quick response 🙂
One more question, When I power the board on the wheel start spinning backward and keep beeping.Then I twist the throttle a little bit more then the motors go forward no beeping at all seem like normal but when released the
throttle then the board keep beeping and wind backward again.
Any solution for that? Thanks
Note: used an ebike twist throttle for the Speed testing
We are using two potentiometers one for speed and one for direction adjust the potentiometer in middle then it will not move backwards also stopped the beep thanks fo comments and subscribing me please share with your friends next week I will upload an other video in that it is fixed with cycle and speed control machnism also different
hey thanks for your video. how can I downlod d
the sorftware?
Github link
Can u fix mime also
ضرور جناب sure
How to flash ARM STM32 RCT6 99JH 98 , keep error can not connect to device. But i can upgrade the firmware st-link V2. Tried stm32 cube programmer and the older stm32 utiliy program.
Same error.
When you receive this message disconnect and reconnect again if you watch the video I explain clearly when this tricky step is required thank you ☺️
@@MKRCLabs
I did but it did not make a difference.
Just hear hoverboard beeps.
Check your st link v 2 good or change it and try
@@MKRCLabs
Checked st link v2 three times, maybe the 4 pins wiring hoverboard should be different its a chinese stm32 imitation mainbord(red color)
@@antoonsorg check the power with meter if already you connected the power also what about switch be care full for power supply cables can you watch again video it is with full details for connection
Se puede controlar por RC con receptor ppm?
si
I have a controller using 72v 45a stm32 i want to increase its speed how can i do it
is it Votol ?
@@85daniels no lingbo
I will heat up this hoverboard motor not design for high speed any how run with out Hal sensors feed back
Kordia
Bhai jan ap pakistani ho
جی جناب
A
hello bro i need your help on hoverboard can you give me a contact address please
Sure
@@MKRCLabs I would be very grateful if you give me your contact address.
Nice