Hi, Thanks a lot for the tutorial! It Worked! I have a few questions if you don't mind answering: 1. Shouldn't we change the extended router's connection type to static instead of dynamic as the main router might assign Extended router a different IP address? 2. Why did you choose 2.4 GHz WDS and not 5GHz? Won't 5GHz be faster? I'm trying to change it back now, but the option is gone since I can't tick it now and its faded. Do I have to factory reset it and follow the steps again? 3. When do we have to reboot and when is it required? Do we have to do it after every setting we change?
@@DoTechRescue, no I just can't figure how to connect wirelessly for range extending. The instructions seem to focus on something else. I want to keep my current connection, but I just want it to reach further.
Sir i have built connection using WDS between two tplink routers A and B . Router B has internet connection by cable network and In router A WDS is enabled but I cannot use the Access Control to restrict websites from internet on router A So i need help to maintain a internet connection from router A with some websites blocked Kindly make a video or reply and help me . Conclusion: how to use WDS and Access control on WDS enabled router at same time
the router is still brodcasting it's old SSID, not the one I connected to via WDS. I get internet via ethernet from the extender but it's not extending the wifi, what could be the problem?
দাদা একটা উপকার করবেন।আমার কিছু ইউজার আছে যাদের না পারছি ব্লক দিতে না পারছি ব্যবহার করতে।এখন আমি চাচ্ছি যাদের কানেক্ট করে দিয়েছি ওদের স্পিড কমায় দিতে চাই।।২০ কেবি করে দিতে চাই। আমি লিমিট করতে পারি কিন্ত ওইটা করলে ওরা বুঝতে না পারে। ওরা যাতে কোন ভাবে না জানতে পারে এমন ব্যবহার করতে পারি।প্লিজ একটা লিঙ্ক দেন দাদা।অনেক উপকার হতো
Hi, thanks for the explanation. I have a doubt by doing this configuration I can obtain a speed higher than 100 Mbps. Since in this model the ports are Fast-Etherne and with cable it only reaches 100 Mbps, taking into account that my current speed in my main router is 300Mbps Thank you!
Hi, thank you for the support. in this model . fast ethernet ports have only maximum 100 Mbps speed . if you use a higher router have Gigabyte ethernet port you can have a speed upto 1000Mbps.
I followed the steps twice now but when I get to the end and reboot the router, once it is rebooted I can no longer access it and get an error message saying connection timed out.
Its Working. Thank you. You saved me lot of time.
Hi,
Thanks a lot for the tutorial! It Worked!
I have a few questions if you don't mind answering:
1. Shouldn't we change the extended router's connection type to static instead of dynamic as the main router might assign Extended router a different IP address?
2. Why did you choose 2.4 GHz WDS and not 5GHz? Won't 5GHz be faster? I'm trying to change it back now, but the option is gone since I can't tick it now and its faded. Do I have to factory reset it and follow the steps again?
3. When do we have to reboot and when is it required? Do we have to do it after every setting we change?
1:27. ur saying enter IP address same as root router, bit ur typing another IP address?..
No, he is not. For the extended router, you should choose an IP address outside the DHCP range but within the same subnet of the main router.
Thank you it worked
You're welcome!
thanks aloot sir ❤🌼
Most welcome
Excellent bro !
Merci
Work successfully...
can i connect the archer c50 with my modem in my basement wirreless with the wds and it works ? And if i fix that can i game with ethernet cable?
You can Extend your wireless in basement modem by using WDS . Please watch video and configure as per direction
@@DoTechRescue i have a diffrent looking menu then you can you help me
Excellent! It’s working! 👏
Thanks
Mine still says no Internet even after I rebooted, anyway I can fix this
You don't show attachment. For range extender, is it necessary to connect the C60 to the modem? Or can it be done wirelessly?
Need extender mode? You have to connect modem via wirelessly.
@@DoTechRescue, no I just can't figure how to connect wirelessly for range extending. The instructions seem to focus on something else. I want to keep my current connection, but I just want it to reach further.
@@dthievinвторой роутер будет иметь свою сеть - распространяя вашу сеть дальше.
When checking connection on command promt, its saying destination host unreachable
Restart router and check
Destination host unreachable while pinging,what to do?
Send screen shot to email
Worked perfectly. And subscribed
Sir i have built connection using WDS between two tplink routers A and B .
Router B has internet connection by cable network and In router A WDS is enabled
but I cannot use the Access Control to restrict websites from internet on router A
So i need help to maintain a internet connection from router A with some websites blocked
Kindly make a video or reply and help me .
Conclusion: how to use WDS and Access control on WDS enabled router at same time
Эта функция там не работает вообще. Тплинк имеет ее просто так. Она не работает.
the router is still brodcasting it's old SSID, not the one I connected to via WDS. I get internet via ethernet from the extender but it's not extending the wifi, what could be the problem?
@iindgren please reset device and try again
দাদা একটা উপকার করবেন।আমার কিছু ইউজার আছে যাদের না পারছি ব্লক দিতে না পারছি ব্যবহার করতে।এখন আমি চাচ্ছি যাদের কানেক্ট করে দিয়েছি ওদের স্পিড কমায় দিতে চাই।।২০ কেবি করে দিতে চাই। আমি লিমিট করতে পারি কিন্ত ওইটা করলে ওরা বুঝতে না পারে। ওরা যাতে কোন ভাবে না জানতে পারে এমন ব্যবহার করতে পারি।প্লিজ একটা লিঙ্ক দেন দাদা।অনেক উপকার হতো
Can we use the same for extending the 5g network?
can we wirelessly use it as wifi range extender or have to buy wifi range extenders not this one?
Yes . You can use it as a wireless extender by using wds methos
@@DoTechRescue thankyou bro for replying
Hi, thanks for the explanation. I have a doubt by doing this configuration I can obtain a speed higher than 100 Mbps. Since in this model the ports are Fast-Etherne and with cable it only reaches 100 Mbps, taking into account that my current speed in my main router is 300Mbps Thank you!
Hi, thank you for the support. in this model . fast ethernet ports have only maximum 100 Mbps speed . if you use a higher router have Gigabyte ethernet port you can have a speed upto 1000Mbps.
I followed the steps twice now but when I get to the end and reboot the router, once it is rebooted I can no longer access it and get an error message saying connection timed out.
kindly share the screenshot to "dotechrescue@gmail.com"
This is the wifi range extender? Changing to dd wrt will be better to make it work?
No its a router .but you can also configure as range extender using WDS function
I dont have advanced seting
brother which version are you using ?
Switch to router mode
It’s saying it cannot be in same subnet mask
Check ip again
Idk what’s happening but after that it gets connected to that wifi and all of a sudden the wifi shows only one light
It basically disconnects
Send screenshot shot - dotechrescue@gmail.com
Not working router keeps restart
Please reset your router and reconfigure
@@DoTechRescue already try a few times but the router keep restart after configure
@@muhdzahid5915 please check your router with normal operation mode
Not working , error is WAN PORT Unplugged
kindly repeat the steps .
well i connected it
but now i can't access my setup page
its go out the root router
How can i goto my archer c60 webpage
root router is not mine
Connect to your router > open command prompt> type “ipconfig”> find gateway address > copy and paste into we browser and try to login
Connect with your computer via Ethernet cable
I love you man
Great
It worked but i am getting low speeds. I havr a 150mb connection and i am getting like 60mbps on 5ghz and ethernet
Not working
Whats the error?