Nice! My pump strainer was completely full of pocket change, driver bits, USB thumb drives, screws, etc - and a rubber tile spacer had gotten by and brought my washer to it's knees. This worked beautifully - Thanks!
Monte : Exactly right. Who knew that my wife's Bobby pin would completely disrupt the operation of the machine. Removed it and all is well. Great video. Thanks
Thanks for video. Saved me a few hundred bucks for a service call. Your video taught me to remove the pump motor and check the impeller for blockages. No blockages but discovered the impeller had broken off. I was then able to order only the pump motor from Amazon for $43.00 whereas other part sites only sold the entire pump and motor assembly for $146.00. Thanks again. Cheers.
Thank you so much for this excellent video. I managed to take apart my pump and clean SAND out from it as it wasn't pumping. It is now working again properly! I think you saved me £100. SUBSCRIBED
Thanks to your clear explanation i was able to fix my washing machine -for the first time in my life-. I was happy, two times; that i did myself and that you saved me 150 euros. Thank you very much!!
Mine wasn't draining so followed your vid. Nothing blocked and meter reading fine so guess pump had internal fault (was 4+ years old). Sourced one from eBay for £21 and all is good. Saved £360 we were about to spend on a new machine so cheers.
Massive thanks for the video. Have the same pump and video gave me the confidence to trouble shoot and fix it. Cost of repair was 2 hours of mine time instead of an expensive engineer call out.
Brilliant! Just what I was looking for. My dishwasher pump is noisy and I thought that maybe I could check for clogs before replacing. Thanks very much.
Found your video after I repaired my pump. I had to take the impeller out as fine sand had made it's way the impeller assembly and 'locked' it. After rinsing, drying it out and re-assembly - it worked like new.
Thanks for the tips Upon inspection of my pump it wasn't open circuit but 120ohms with a lot of side play in the impeller shaft. Testing it directly with 240vac the impeller showed would spin once then stall or just hum at any given random sequence Im guessing because of the large worn torrance between the rotor and the stator it now appears to be electrically and mechanically unusable Answer: TIME FOR A REPLACEMENT
dude you just saved me $500 about to buy a new machine, took the pump off and it was full of the girls bobby pins- best advice and great video. thanks heaps
Thanks for your video, a fresh approach to this problem. Most just advise that we replace pump without 1st having checked to see if that part is still working It happened to me where I bought a new pump on ebay and after a week long wait, it turns out that the previous pump was ok. I then removed the drain hose and clean it out. D problem still hasn't been solved, I am contemplating removing the entire sump tomorrow hoping this might finally sort the problem or reveal the cause of the blockage.
Nice! Mine (actually a temporary replacement until our REAL machine is repaired after some freezing damage during a winter move) pumped noisily once and now it won't pump (just a buzzing sound coming from the pump with very little vibration) so I'm hoping when I take it apart tomorrow morning that I'll find some bobby pins and fluff in there.
Thanks for posting this video. I didn't end up having any clogged items in the pump, but the valve was stuck inside which proved to be the problem. It works now, but I'll likely have to order a new part if the valve sticks again. There was also some slime build up that I cleaned while I was there.
So that debree was the problem thats good information thanks thats going to help a lot.i have a question though when would you need to pull the motor out?what would the dishwasher need to be doing to approach it like that? Sorry and thank you.
Thank you very much sir i will try to fix the problem first by using your expert advice and suggestion. I think it may be worth trying before just assuming the pump is dead. Appreciate the post. Love this kind of work.
your video was great, and I confirmed that mine was working with ohm test....nothing in impeller, but there was a clogged filter in a boot just before the pump.....some coins, cut ends of zip ties, a screw, plastic and some gunk.....the filter looks like a large test tube with holes in the bottom (mine is affinity washer)....
Thank you so much! Looking through your videos gave me the confidence to give it a go (with no previous experience/ability). I was able to retrieve and remove a small amount of material in the pump and I didn't even break a nail in the process...RESULT! :-)
Washing machine started making a terrible noise yesterday so thanks to your video I stripped down the pump and found a hair grip stuck inside. Thank you very much!
Normally you dont have to take the pump out. Just tip washing machine up unplug the hoses of the pumb and feel inside for whatever is stopping the impeller to turn. Thats it.
we have a - Siltal - washing machine, that was made in Slovenia or Italy. the factory long has closed. But uses or better used many BOSCH insides.17 (seventeen) years old. we use it daily. The only thing we replaced was the main belt. a belt for the water pump. electric brushes for the pump motor. but now it looks the pump has finally given up. we will get the tester from an outside source and do the check if the pump is dead or not. back now... pump, the same blue -box- that you have. we also had first removed some things that were wrapped around the propeller. pump did not work. so we tested it directly.connnected the pump directly with a cable and plug. the pump was working. so, we are looking further, why it is not discharging water. maybe something more inside is blocked? we will dig... ok, back for the final. we removed all the hairs and lint and bits and pieces from the propeller. scratched off a little lime here, opened the pipes, blew through them to make sure all were free. connected everythign together. and it works just fines. could it be that sometimes a good shake and scatch and clean up will do the trick as well? anyway, the machine is still good and we will not sell it just because it is old. and our friend, the engineer said, should we decide to sell, only to him. because the machine still has many good and useful parts inside. looks like 17 years ago they did make GOOD things.
Thanks for the video. My machine washes and drains but won't always spin. If I'm lucky it spins. Sometimes I have to remove part of the load and spin in it two lots, even then it doesn't always work. I've checked the filters. The machine makes a strange noise at the start of the draining process but it proceeds to drain, just won't spin. I wonder if you think it's worth checking the pump?
Hi, Thanks, I have the hoover Performa ECO AB130, and the pump starts growling when on number five setting ( rinse and cold water fill ), sounds like a dry bearing, does the pump run in reverse when emptying ?, nice video, but it would have been better if you had shown it being removed from the machine. Thanks. Rick.
Thanks, Sire! Inspired me to check out the pump in our Whirlpool (Ikea) dish washer and indeed, I found there a piece of glass (damn wife with her wine glasses) and now it works like a charm again. Guys like you we need!
Greetings. Great detailed video!! I loved it. I have a front load Samsung with pump in back. Machine works for the most part but won't go into spin cycle from rinse.Pump seems to work for draining water from inside of the tub but does NOT get water underneath the inside of tub. I can hear it sloshing around when I manually spin the tub after machine stops. I've taken the pump apart twice and cleaned a little lint that was inside. Also checked and cleaned sump hose. No change in the operation. Is the leftover water normal to be there or is this pump malfunctioning somehow? Much Appreciated!! Daniel
very helpfull video my machine wasnt emptying and after looking at my pump i found it blocked thanks you saved me £80.00 for someone just to take a look at it
I found out recently after using multimeter on my washing machine pump that even though it passes the test, it doesn't necessarily mean it works continuously while in operation. I kept getting a F-02 and "Suds" code on my washer. I tested everything. Logically I thought that if water was not draining from tub it has to be weak or dead pump. However the pump was showing perfect readings. I swapped out pump and washer is working great and draining. Sometimes you just never know.
@Dan S. Normally most machines empty completely after a cycle. I'm not a washing machine engineer but perhaps there is a level switch in the machine that is faulty?
Hi! Very informative video. ON my washing machine I was receiving LED flashes that corresponded in my manual to a "clogged pump" I took the base off, removed the hoses attached to pump, and then removed the pump itself. I disassembled it like the video here, but there was no blockage, nothing. I then reassembled everything and am reciving the same error. Is it a control panel error? I do not have a multi meter to check the circuit. How important is that step? Any suggestions?
Hi. I have a Bosch washing machine that won't wash. It fills, heats up and drains but won't go into a cycle - not even rinse or spin - although it did spin once during my fixing attaempts. I've squirted water back up the outlet pipe into the machine via a garden hose pipe and drained it to try and dislodge any grunge - some came out - but it still won't start. Could it be the blocked pump as per your Video? Good video by the way.
Great vid. Why is it that the washer makers don't have some sort of screen to stop debris from entering the pump and ceasing it up. Sick of the same prob over and over yet?
Didnt know you could access the pump from underneath, brilliant, thanks. Oh and just a quick question, id like to test my pump could you recommend a general multi meter i could buy?
Hi there. Great video. Thanks for posting it. I have ordered a new pump as my current one is buzzing and vibrating like mad. Only question I have is when I test it with my multimeter I get around 200 as a result. Very different to what you had. Does that just mean that it’s trashed?
Different makes will have different values, unless you know the specific value it is hard to say if it is faulty or not unless it is completely open circuit. Thanks for the comment
Thank you for this video it was much appreciated I tested the resistance on the pump it worked then I took it apart and there was a little metal pin lodged between the pump and the side removed it and that was it.
I've unplugged and re plugged. Should I pop the circuit switch on and off too? I'm getting a multi meter after work today and will check the drain pump with it, If it is an open circuit would the problem then be in the circuit board?? I can open that and make sure everything is tightly connected still. Thanks for your help!
Hmmm...now that you say that...it is on the bottom in the dead centre and is very small...so maybe it is as you say...does it fail as there is some kind of abnormal pressure building up and so the hole fails first ? I have to say though that the machine is just about 18 months old...not long to my mind...I have found where I can buy a pump local to me for about £18...thanks for the reply.
A lot of washing machines from many brands use identical generic drain pumps. Unfortunately because of their cheap design they need to be replaced more often than needed.
My washer wouldn't drain i removed the pump and there was small sock stuck in there, Put it back together it solved the problem but now I have a small drip coming from in between the pump and the assembly. I tried taking off and back on a couple times appears to be seated correctly all around but doesn't have that tight feel it originally and still drips. Any ideas?
Thanks, I tried a few more times and finally got it to stop dripping, i believe the o-ring wasn't seating correctly after twisting the pump into the locked position.
Hello good afternoon, how are you? I'm watching your videos and they're very educational, congratulations, the next I got a friend's gift from a washing machine wipool duet model 9200, a beautiful washing machine I was very happy with the present, but she has a problem that I can not figure out , When I press the button to connect it emitted a sound signal and not of the match, I am a test asoprando the tube of the pressure switch to it of the start but not stops of filling of water, it is that can help me, I am from Brazil and I have difficulties with mechanics , Because it is an imported washing machine of uses, do not want to sew. I'll try to repair it myself with your help. Thank you.
Hello, My knowledge of washing machines is very limited and I only really know about the motor (brushes) and the pump and how to replace circuit boards etc. You might be better off asking in a dedicated forum like this- bit.ly/2l4plvB
Hi, I just took out my drain pump one thing I realized is propeller isn't turning easily. It turns but it feels like there is spring inside shaft or something. I didn't put it back yet. however, the propeller was clean when I took the pump out. I was thinking the buy a new pump but I m not sure if the pump is bad since my dishwasher isn't draining at all.
i have replaced the water drain pump on my frigidaire afinity washer but it continues to mark "no-spin". Any ideas on what else i can do to fix my washer? please help.
hi handyman i have got one issue too my haeir washing machine doesn't spin... first it started making noise while drying so i thought i should not use until this noise thing stops after a week i found out that the drainer works re ally slow and the dryer doesnt run at all what shall i do need help please
Hi there, I have been having some trouble with my washer. It is a maytage front load. "suds" keeps pooping up and is not spinning or draining properly. I did take apart the pump and found coins in it. I did take them out and cleaned it put it back together. I should add that 2 of the 3 blades where damaged. Im thinking that just the 1 blade is not able to pump the water out. Do I need to replace the pump? Or am I able to just get that part with the blades on it?
Yes, you need to replace the pump. I don't think you can swap the impeller as I am not sure how it is fixed. A new pump should not be that expensive anyway ;-)
I'm not sure how much pressure such a pump would provide. I think you are better off with a 12v pump as it's a much safer voltage when working with water.
When replacing water pump on Top Loader there is a rear pump hose that exits the rear of the Bottom of the Washing Machine from the new water pump. DO NOT attach the short rubber hose from the water pump to the rear of the machine when the machine is tilted on its side this is because the short hose will come loose when you tilt the machine back up again and water will drain on the floor. You must remove the back panel of the machine when it is upright then reach in and attach the short outlet hose from the water pump to the rear inner outlet with the metal outer ring to sleeve. Then reach inside washing machine drum and rotate freely to test the hose connection. Ensure the hose inner tubes are all connected to the water pump with there metal rings on inlets and outlets as machine is STANDING UPRIGHT before fixing on the back panel. You only replace the water pump when the machine is tilted on its side.
hi sir can u tell me if is there a relation between pump failure and machine spin,coz my wife put a doll full of plastic granules that opened and clogged my pump,i did wot u did but the machine wont pump out with a spin at the same time ,by the way my pump is a mirror image of urs its a G.E front loading W56 made in uk kindly advice me dude.
HI again. This seems to be developing further. I've gone ahead and tested the Drain pump with the multimeter. It beeps, and when I put it in resistance mode I get a higher number than with the two prongs by themselves, but it still has continuity. I'm going to go ahead and order a new drain pump anyways. But I fear there's nothing wrong with it and the problem is elsewhere. Any suggestions?
Hi Handy man my washer dryer is not draining properly ..And so i had to drain all the water out my self from a pipe leading to the trap, i unblocked the pipe and put it back on ...I then put the machine back on spin when it was empty and it spun ok...when i put another wash on the machine still would not empty with water ..is it the pump or the motor that needs replacing ...Thanks Aly
+ANGEL DAVIS Normally you unplug the machine and tip it backwards and the pump will be accessible from underneath. Or most machines have a small filter at the front now, there is often a small panel on the front of the machine where you can pull the flap down and then unscrew the filter.
Your video was exactly what I needed to fix my dishwasher. Thank you so much!
I'm glad the video helped
Thanks for the comment 👍
Nice! My pump strainer was completely full of pocket change, driver bits, USB thumb drives, screws, etc - and a rubber tile spacer had gotten by and brought my washer to it's knees. This worked beautifully - Thanks!
You are welcome.
Thanks for the comment
Monte : Exactly right. Who knew that my wife's Bobby pin would completely disrupt the operation of the machine. Removed it and all is well. Great video. Thanks
Thanks for video. Saved me a few hundred bucks for a service call. Your video taught me to remove the pump motor and check the impeller for blockages. No blockages but discovered the impeller had broken off. I was then able to order only the pump motor from Amazon for $43.00 whereas other part sites only sold the entire pump and motor assembly for $146.00. Thanks again. Cheers.
+Robin Taketa
Brilliant ;-)
I'm glad the video helped.
Thanks for the comment
Thanks from the U.S. - got the washing machine running with help from this video.
Glad it helped!
Thanks for taking the time to help others.
Thank you so much for this excellent video. I managed to take apart my pump and clean SAND out from it as it wasn't pumping. It is now working again properly! I think you saved me £100. SUBSCRIBED
I'm glad the video helped ;-)
Thanks for the comment
It took me half an hour of video searching to find this! Hopefully it's what I'm looking for - thanks so much!
You are welcome
Thanks for the comment 👍
@@ultimatehandyman it didn't work unfortunately, think it's time for a new pump. Cheers though!
Thanks for the video. It saved me 300 dollars
Great to hear!
Thanks to your clear explanation i was able to fix my washing machine -for the first time in my life-. I was happy, two times; that i did myself and that you saved me 150 euros. Thank you very much!!
Mine wasn't draining so followed your vid. Nothing blocked and meter reading fine so guess pump had internal fault (was 4+ years old). Sourced one from eBay for £21 and all is good. Saved £360 we were about to spend on a new machine so cheers.
Well done for fixing it yourself ;-)
Thanks for the comment
Massive thanks for the video.
Have the same pump and video gave me the confidence to trouble shoot and fix it.
Cost of repair was 2 hours of mine time instead of an expensive engineer call out.
Brilliant! Just what I was looking for. My dishwasher pump is noisy and I thought that maybe I could check for clogs before replacing. Thanks very much.
Found your video after I repaired my pump. I had to take the impeller out as fine sand had made it's way the impeller assembly and 'locked' it. After rinsing, drying it out and re-assembly - it worked like new.
Thanks for the comment 👍
Thanks for the tips
Upon inspection of my pump it wasn't open circuit but 120ohms
with a lot of side play in the impeller shaft.
Testing it directly with 240vac the impeller showed would spin once
then stall or just hum at any given random sequence
Im guessing because of the large worn torrance between the rotor and the stator
it now appears to be electrically and mechanically unusable
Answer: TIME FOR A REPLACEMENT
My issue as well.
dude you just saved me $500 about to buy a new machine, took the pump off and it was full of the girls bobby pins- best advice and great video. thanks heaps
Thanks for your video, a fresh approach to this problem. Most just advise that we replace pump without 1st having checked to see if that part is still working It happened to me where I bought a new pump on ebay and after a week long wait, it turns out that the previous pump was ok. I then removed the drain hose and clean it out. D problem still hasn't been solved, I am contemplating removing the entire sump tomorrow hoping this might finally sort the problem or reveal the cause of the blockage.
Nice! Mine (actually a temporary replacement until our REAL machine is repaired after some freezing damage during a winter move) pumped noisily once and now it won't pump (just a buzzing sound coming from the pump with very little vibration) so I'm hoping when I take it apart tomorrow morning that I'll find some bobby pins and fluff in there.
Thanks for posting this video. I didn't end up having any clogged items in the pump, but the valve was stuck inside which proved to be the problem. It works now, but I'll likely have to order a new part if the valve sticks again. There was also some slime build up that I cleaned while I was there.
You help us fix our washer good sir! Thank you! Subscribed
I'm glad the video helped
Thanks for the comment 👍
Thank you sir! Your video helped save me some money and a headache.
You're welcome!
Thanks for the comment
thanks for the video it shines light on what might be the problem with my washing machine.
So that debree was the problem thats good information thanks thats going to help a lot.i have a question though when would you need to pull the motor out?what would the dishwasher need to be doing to approach it like that? Sorry and thank you.
Thank you very much sir i will try to fix the problem first by using your expert advice and suggestion. I think it may be worth trying before just assuming the pump is dead. Appreciate the post. Love this kind of work.
Thank you so much. Plain simple advice, which helped me to fix my own machine. Brilliant.
I'm glad the video helped
Thanks for the comment 👍
your video was great, and I confirmed that mine was working with ohm test....nothing in impeller, but there was a clogged filter in a boot just before the pump.....some coins, cut ends of zip ties, a screw, plastic and some gunk.....the filter looks like a large test tube with holes in the bottom (mine is affinity washer)....
Thank you so much! Looking through your videos gave me the confidence to give it a go (with no previous experience/ability). I was able to retrieve and remove a small amount of material in the pump and I didn't even break a nail in the process...RESULT! :-)
Washing machine started making a terrible noise yesterday so thanks to your video I stripped down the pump and found a hair grip stuck inside. Thank you very much!
Thanks for the vid. I'm getting tons of lint in my newly washed clothes. Someone mentioned it could be in the pump. Do you agree that's a possibility?
Thanks a lot handy man.You saved my washing machine!!
Normally you dont have to take the pump out. Just tip washing machine up unplug the hoses of the pumb and feel inside for whatever is stopping the impeller to turn. Thats it.
we have a - Siltal - washing machine, that was made in Slovenia or Italy. the factory long has closed. But uses or better used many BOSCH insides.17 (seventeen) years old. we use it daily. The only thing we replaced was the main belt. a belt for the water pump. electric brushes for the pump motor. but now it looks the pump has finally given up. we will get the tester from an outside source and do the check if the pump is dead or not.
back now... pump, the same blue -box- that you have. we also had first removed some things that were wrapped around the propeller. pump did not work. so we tested it directly.connnected the pump directly with a cable and plug. the pump was working. so, we are looking further, why it is not discharging water. maybe something more inside is blocked? we will dig...
ok, back for the final. we removed all the hairs and lint and bits and pieces from the propeller. scratched off a little lime here, opened the pipes, blew through them to make sure all were free. connected everythign together. and it works just fines. could it be that sometimes a good shake and scatch and clean up will do the trick as well? anyway, the machine is still good and we will not sell it just because it is old. and our friend, the engineer said, should we decide to sell, only to him. because the machine still has many good and useful parts inside. looks like 17 years ago they did make GOOD things.
Excellent with good clear instructions.....even if my washer is ok,
its a friends dishwasher I have to sort v.soon
Thanks for the video, gave me the confidence to try to fix ours myself. Worked great.
Thanks for the video. My machine washes and drains but won't always spin. If I'm lucky it spins. Sometimes I have to remove part of the load and spin in it two lots, even then it doesn't always work. I've checked the filters. The machine makes a strange noise at the start of the draining process but it proceeds to drain, just won't spin. I wonder if you think it's worth checking the pump?
Hi,
Thanks, I have the hoover Performa ECO AB130, and the pump starts growling when on number five setting ( rinse and cold water fill ), sounds like a dry bearing, does the pump run in reverse when emptying ?,
nice video, but it would have been better if you had shown it being removed from the machine.
Thanks.
Rick.
Thanks, Sire! Inspired me to check out the pump in our Whirlpool (Ikea) dish washer and indeed, I found there a piece of glass (damn wife with her wine glasses) and now it works like a charm again. Guys like you we need!
Greetings. Great detailed video!! I loved it. I have a front load Samsung with pump in back. Machine works for the most part but won't go into spin cycle from rinse.Pump seems to work for draining water from inside of the tub but does NOT get water underneath the inside of tub. I can hear it sloshing around when I manually spin the tub after machine stops. I've taken the pump apart twice and cleaned a little lint that was inside. Also checked and cleaned sump hose. No change in the operation. Is the leftover water normal to be there or is this pump malfunctioning somehow? Much Appreciated!! Daniel
very helpfull video my machine wasnt emptying and after looking at my pump i found it blocked thanks you saved me £80.00 for someone just to take a look at it
I found out recently after using multimeter on my washing machine pump that even though it passes the test, it doesn't necessarily mean it works continuously while in operation. I kept getting a F-02 and "Suds" code on my washer. I tested everything. Logically I thought that if water was not draining from tub it has to be weak or dead pump. However the pump was showing perfect readings. I swapped out pump and washer is working great and draining. Sometimes you just never know.
👍
had kitchen upgrade . machine worked fine before work started. now won't drain full of grit
Saved our bacon. Can't thank you enough for this helpful video.
@Dan S.
Normally most machines empty completely after a cycle.
I'm not a washing machine engineer but perhaps there is a level switch in the machine that is faulty?
+Ultimate Handyman
Thanks! I'll try and look into the level switch. I just changed the pressure sensor and no change.
Dan
Great video saved my machine big thumbs up👍👍
Thanks for the comment
Hi! Very informative video. ON my washing machine I was receiving LED flashes that corresponded in my manual to a "clogged pump" I took the base off, removed the hoses attached to pump, and then removed the pump itself. I disassembled it like the video here, but there was no blockage, nothing. I then reassembled everything and am reciving the same error.
Is it a control panel error? I do not have a multi meter to check the circuit. How important is that step? Any suggestions?
Hi. I have a Bosch washing machine that won't wash. It fills, heats up and drains but won't go into a cycle - not even rinse or spin - although it did spin once during my fixing attaempts. I've squirted water back up the outlet pipe into the machine via a garden hose pipe and drained it to try and dislodge any grunge - some came out - but it still won't start. Could it be the blocked pump as per your Video? Good video by the way.
Thanks, it's worth checking the pump to see if it is clear.
Many thanks. I'll give it a go
Great vid. Why is it that the washer makers don't have some sort of screen to stop debris from entering the pump and ceasing it up. Sick of the same prob over and over yet?
the mechanics need also work and rip off the clients..
Didnt know you could access the pump from underneath, brilliant, thanks. Oh and just a quick question, id like to test my pump could you recommend a general multi meter i could buy?
I bought mine from Maplin, but there are quite a few to choose from depending on how much you want to spend- fave.co/2m8aT3y
Thanks for the comment
Hi there. Great video. Thanks for posting it.
I have ordered a new pump as my current one is buzzing and vibrating like mad.
Only question I have is when I test it with my multimeter I get around 200 as a result. Very different to what you had.
Does that just mean that it’s trashed?
Different makes will have different values, unless you know the specific value it is hard to say if it is faulty or not unless it is completely open circuit.
Thanks for the comment
Thank you for this video it was much appreciated I tested the resistance on the pump it worked then I took it apart and there was a little metal pin lodged between the pump and the side removed it and that was it.
Thanks for the comment ;-)
Great tip, now hook it up with a pair of testleads and energize it to see it actually operating before installing it back into the washer!
+Liberty Patriot
I'm afraid you are about 5 years too late ;-)
Thanks for the comment
where can I buy a piece that spins around to take the water out
I've unplugged and re plugged. Should I pop the circuit switch on and off too? I'm getting a multi meter after work today and will check the drain pump with it,
If it is an open circuit would the problem then be in the circuit board?? I can open that and make sure everything is tightly connected still.
Thanks for your help!
thank you very much sir! thanks to you, 100 bucks stayed in my pocket..
You are welcome
Thanks for the comment
Hmmm...now that you say that...it is on the bottom in the dead centre and is very small...so maybe it is as you say...does it fail as there is some kind of abnormal pressure building up and so the hole fails first ? I have to say though that the machine is just about 18 months old...not long to my mind...I have found where I can buy a pump local to me for about £18...thanks for the reply.
Thank you. Our extended warranty doesn't cover blockages so would require an expensive call out and repair. This could just well solve it.
If you were to spin the impellor, does it go into a free spin or is there like a springy resistance that keeps it from free spinning?
No, it is not free spinning, you can feel resistance from the magnets when you rotate it.
Thanks for the comment 👍
A lot of washing machines from many brands use identical generic drain pumps. Unfortunately because of their cheap design they need to be replaced more often than needed.
My washer wouldn't drain i removed the pump and there was small sock stuck in there, Put it back together it solved the problem but now I have a small drip coming from in between the pump and the assembly. I tried taking off and back on a couple times appears to be seated correctly all around but doesn't have that tight feel it originally and still drips. Any ideas?
*****
It sounds like it may need a new "O" ring for it to seal properly.
Thanks, I tried a few more times and finally got it to stop dripping, i believe the o-ring wasn't seating correctly after twisting the pump into the locked position.
Excellent video. well describe in a short period of time
thank you
+Mario Lemoine
You are welcome
Thanks for the comment;-)
Hello good afternoon, how are you? I'm watching your videos and they're very educational, congratulations, the next I got a friend's gift from a washing machine wipool duet model 9200, a beautiful washing machine I was very happy with the present, but she has a problem that I can not figure out , When I press the button to connect it emitted a sound signal and not of the match, I am a test asoprando the tube of the pressure switch to it of the start but not stops of filling of water, it is that can help me, I am from Brazil and I have difficulties with mechanics , Because it is an imported washing machine of uses, do not want to sew. I'll try to repair it myself with your help. Thank you.
Hello, My knowledge of washing machines is very limited and I only really know about the motor (brushes) and the pump and how to replace circuit boards etc. You might be better off asking in a dedicated forum like this- bit.ly/2l4plvB
Thanks mate. Will be doing this one day this holiday weekend.
+spaztech
You are welcome
Thanks for the comment
Hi,
I just took out my drain pump one thing I realized is propeller isn't turning easily. It turns but it feels like there is spring inside shaft or something. I didn't put it back yet. however, the propeller was clean when I took the pump out. I was thinking the buy a new pump but I m not sure if the pump is bad since my dishwasher isn't draining at all.
do i need to put silicon or adhesive when putting back the pump together to get a better water seal?
No, providing everything is clean, it should be fine. You could use a little silicone grease, if the components are tight 👍
i have replaced the water drain pump on my frigidaire afinity washer but it continues to mark "no-spin". Any ideas on what else i can do to fix my washer? please help.
Very nice video.
have maytag neptune TL...FAV6800AWW.....need to replace the outer tub (plastic) seal and bearing?????
Thanks for your reply. I will have a look today.
Any tips to open the drain cap when it is stuck?
I used a pair of water pump pliers last time, but you have to be careful not to break the plastic ;-)
@@ultimatehandyman I tried with no luck. Any other things that I can try lot applying soap etc?
Thank you!
Excellent tutorial
Yep was a bobby pin for me too. Thanks heaps!
hi handyman i have got one issue too my haeir washing machine doesn't spin... first it started making noise while drying so i thought i should not use until this noise thing stops after a week i found out that the drainer works re
ally slow and the dryer doesnt run at all what shall i do need help please
Hi there, I have been having some trouble with my washer. It is a maytage front load. "suds" keeps pooping up and is not spinning or draining properly. I did take apart the pump and found coins in it. I did take them out and cleaned it put it back together. I should add that 2 of the 3 blades where damaged. Im thinking that just the 1 blade is not able to pump the water out. Do I need to replace the pump? Or am I able to just get that part with the blades on it?
Yes, you need to replace the pump. I don't think you can swap the impeller as I am not sure how it is fixed. A new pump should not be that expensive anyway ;-)
do you reckon i could use the pump off an old washing machine to hook up to my water butt to get some more pressure to feed a hosepipe?
I'm not sure how much pressure such a pump would provide. I think you are better off with a 12v pump as it's a much safer voltage when working with water.
Hi, how do i rempve a sock that is blocking the drain pipe. has the water backing up
we have a bosch classixx 1200 the programme my mam uses for washing the clothes has stopped working
Thank you!
You are welcome
Thanks for the comment 👍
When replacing water pump on Top Loader there is a rear pump hose that exits the rear of the Bottom of the Washing Machine from the new water pump. DO NOT attach the short rubber hose from the water pump to the rear of the machine when the machine is tilted on its side this is because the short hose will come loose when you tilt the machine back up again and water will drain on the floor.
You must remove the back panel of the machine when it is upright then reach in and attach the short outlet hose from the water pump to the rear inner outlet with the metal outer ring to sleeve.
Then reach inside washing machine drum and rotate freely to test the hose connection.
Ensure the hose inner tubes are all connected to the water pump with there metal rings on inlets and outlets as machine is STANDING UPRIGHT before fixing on the back panel.
You only replace the water pump when the machine is tilted on its side.
I've not seen a top loader since I was a kid 😱
Thanks for the comment 👍
hi sir can u tell me if is there a relation between pump failure and machine spin,coz my wife put a doll full of plastic granules that opened and clogged my pump,i did wot u did but the machine wont pump out with a spin at the same time ,by the way my pump is a mirror image of urs its a G.E front loading W56 made in uk kindly advice me dude.
how should the impeller turn should you get resistance and a light dull clunking or does it spin completely freely?
+malcolm martyn
You can normally feel a little resistance in places which I think is caused by the magnet.
cheers for that. problem solved
Thanks
Thank you very much for the kind donation 👍
HI again. This seems to be developing further. I've gone ahead and tested the Drain pump with the multimeter. It beeps, and when I put it in resistance mode I get a higher number than with the two prongs by themselves, but it still has continuity. I'm going to go ahead and order a new drain pump anyways. But I fear there's nothing wrong with it and the problem is elsewhere. Any suggestions?
How is the fan in the motor suppose to rotate
It moves round but does not spin freely until it is energised due to the magnets.
Hi Handy man my washer dryer is not draining properly ..And so i had to drain all the water out my self from a pipe leading to the trap, i unblocked the pipe and put it back on ...I then put the machine back on spin when it was empty and it spun ok...when i put another wash on the machine still would not empty with water ..is it the pump or the motor that needs replacing ...Thanks Aly
+letmeinpleaze Have you tried removing the pump and cleaning it?
Doing that tomorrow ...Thanks for getting back ..
+letmeinpleaze
No problem, good luck with it ;-)
Could it not just be the hose from the motor?
Really appreciate. Thanks mate.
how do you remove the pump to replace it??? mine isn't draining at all
+ANGEL DAVIS Normally you unplug the machine and tip it backwards and the pump will be accessible from underneath. Or most machines have a small filter at the front now, there is often a small panel on the front of the machine where you can pull the flap down and then unscrew the filter.
What machine is it.
Sure only filter needs cleaning
An engineer.
i aint tryed to get into the pump got these 2 big plastic things around the pipes
What if detergent has gone down into where the wheel is on the pump?
Do you mean into the electrical part?
If it has, you might need a new pump!
Thanks for the comment 👍
Thank you for the video just fixed my pump..
Manuel Mendoza
You are welcome
Thanks for the comment
I now feel a lot more confident about repairing a wading machine. More clips on appliance repairs would be great!
I have problem my ge washer leak water its coming from flod hose(outer tube) do you guys think my flod gasket(hose to outer tube) is bad.Thx
my machine wont empty after each spin its a hotpoint wma30 no filter at the front bottom so my guess its the pump
Lifesaver! Thanks mate
You are welcome
Thanks for the comment
what is the part in side the drain pump that spins and forces the water through the hose
+Ian Gomes The Impeller
Cool thanks
+Ian Gomes
You are welcome
Dank u :from Holland.
TKS, big help to fix my Maytag!
this washer no have any filter before pump ?!
you bloody good you are mate
Thanks for the comment ;-)
It wasn't an elastic band you found. It's the rubber seal for the unit.
If it was the rubber seal, how come the pump did not leak when it was refitted to the machine ;-)
Ultimate Handyman
the rubber seal for the unit is the black color one as he shown, that grey one is elastic or hair band.
the rubber seal for the unit is the black color one as he shown, that grey one is elastic or hair band.
sorry ultimate Handyman, I mean my answer is toward eBob.
thanks man,..just fixed mine.
You are welcome
Thanks for the comment
Hi I have a coin stuck in the pump of the washing machine and can't figure out how to take the bottom of the pump off to remove it . Help?!
Hi, this might help- th-cam.com/video/PyPSNz0UiOk/w-d-xo.html