1992 Ducati 900SS, Carburetor sync and adjustments

Syncing the carb ensures they open and flow at the same rate for balanced operation.
/ eldestbuilds
The Facebook page is up and running.

[@gordonlaing8646]

I had a bad plug on my Triumph once. It does drive you crazy

[@ELDESTBuilds]

Most likely, we all have

[@kuantanplateketuk4781]

Hey there , just wondering about the clutch , do we need to pull the clutch will syc the carb? In the video u cable tied the clutch lever

[@ELDESTBuilds]

I only did that to reduce the background noise for the video.

[@karlh4313]

Thanks 👍

[@ELDESTBuilds]

Welcome

[@TheNigelrojo]

I'm just about to synch the carbs on my 1993 900SS. Carbs cleaned & rebuilt, valves re-shimmed, ready to go. The problem I have is getting to that damn balancing screw. I still have the standard airbox (with top removed & square K&N air filter) but getting at that screw is still difficult. I think can do it with a head torch & long screwdriver. However, I notice that you have separate round air filters on each carb. Do you think that would make it run leaner than the square K&N with airbag top removed? It would certainly make carb access easier.

[@ELDESTBuilds]

I don't think it leans it out at all. This one had the K&N on top of the airbox when I bought it. I just didn't like the airbox. There's only two things when you switch. The filters require more cleaning maintenance because they're exposed and when you run in the wet they will get soaked from the front wheel. Not usually a problem for me but it runs a little rough with the wet filters till about 5k. When they start to dry out everything is normal.
If you realy want the ducks guts, get these
th-cam.com/video/vHxbWf-w3k0/w-d-xo.htmlsi=coIMw0dOzQbzH7Q3

[@TheNigelrojo]

Thanks, I appreciate the advice.@@ELDESTBuilds

[@firebird14420]

@Eldest Builds Hey 👋 have you ever check out how to sync carburetor the right way and the wrong way on How To Wrench? It talks about calibration of the carb sync tool. It's only 6 minutes long.. but my left guage is lower points to the left more than the right even when no vacuum is on it. How with that video or how would you calibrate or what do you think?

[@ELDESTBuilds]

I haven't synced my sync but it has four and I probably don't use the same ports all the time. It ran much better after so all is well. Then I put on FCRs and it's even better.

[@firebird14420]

@@ELDESTBuilds I only have a double gauge and the right gauge is for the rear cylinder and the front gauge is for the front. So I'm wondering how I should set it or should I just get another guage..

[@firebird14420]

@@ELDESTBuilds what is a FCR?? 😂

[@ELDESTBuilds]

@@firebird14420 take a reading then flip them and take another and meet in the middle

[@ELDESTBuilds]

@@firebird14420 here you go
th-cam.com/video/vHxbWf-w3k0/w-d-xo.html

[@Ncollins99]

Been looking for vacuum gauges to sync my 94 900SS. Rebuilt the carbs lately and the bike sounds just like yours, pre balancing, Question - where did yah pick-up your vacuum gauges? Having trouble finding the right little 'pipe adapters' for the inlet screw. thanks

[@ELDESTBuilds]

Amazon
www.amazon.com/Prokomon-Motorcycle-Carburettor-Synchronizer-Balancer/dp/B09VPDM66Y/ref=sr_1_3_sspa?crid=2VUQ4P99IK3UR&keywords=carb+synchronizer+tool+motorcycle&qid=1658932603&sprefix=carb+syn%2Caps%2C158&sr=8-3-spons&psc=1&spLa=ZW5jcnlwdGVkUXVhbGlmaWVyPUEzS09FOVJDQllVVzJKJmVuY3J5cHRlZElkPUEwNTY3MzIxMU1SUlpDRzAzUFdDMyZlbmNyeXB0ZWRBZElkPUEwOTIyNDgxMlRQMEtUUzZSSVAyQiZ3aWRnZXROYW1lPXNwX2F0ZiZhY3Rpb249Y2xpY2tSZWRpcmVjdCZkb05vdExvZ0NsaWNrPXRydWU=

[@Ncollins99]

@@ELDESTBuilds Thank ya sir!!!
Great channel by the way!

[@ELDESTBuilds]

Thanks buddy, hope some of those videos are helpful. More and more Amazon has what I need and 2 day delivery ain't bad.

[@johnalden3259]

All good info. So you have idle mix, idle speed and sync. With the gauges ready where do you start? And is there any order to it.

[@ELDESTBuilds]

There's no particular order but any changes made can effect other settings. Get the bike idling is step one for me. Then set mixture the vacuum gauges will help. Then rev it to 3k and sync.

[@ToBikeDuc94]

Wow i wish i had the Knowledge to do this.. greetings from germany IT SOUNDS PERFECT NOW, i Grow up at one of These ..
Today my First bike is a 750 ss sc Form 93/94. i wish i Could give her some better Settings. Sorry my english 👍

[@ELDESTBuilds]

Thanks, I think it is possible for you to sync the carbs just as I did. Find the Ducati club near you. Those guys can help.

[@diegovelez3477]

New Carbs rebuilt kit and LEVEL FLOAT at 15mm

[@ELDESTBuilds]

th-cam.com/video/vHxbWf-w3k0/w-d-xo.html