IE Error LG Washing Machine You Can Fix Easy
ฝัง
- เผยแพร่เมื่อ 5 ต.ค. 2024
- IE error LG washing machine you can fix easy. Lg front load washing machines present ie or 1e error which can easily be reset. IE LG Washer Fault could be caused by a number of issues. We dive more into that repair in this DIY video.
![[UNCUT]"ตุลามรณะ"ย้อนฟังคำทำนาย หมอดูทุกสาย ดวงเมืองร้อน (หมอปลาย ฟองสนาน อ.โอเล่)I คนดังนั่งเคลียร์](http://i.ytimg.com/vi/lE5az5VvT9M/mqdefault.jpg)
Extremely helpful mate, one other thing that will cause an IE error, an improperly placed drainage hose, make sure you have the air gap, or incoming water will just drain out from the drum, stop, then IE error.
We Had An IE error , we changed water pump, we checked the hoses at tap and machine. Turned out that the water inlet above the soap dispenser was completely blocked with hard water caking. We unscrewed and soaked in vinegar and got rid of all the scale and the machine runs like new. All the taps and hoses were completely clear on first inspection
We just had a horrible move and then last night finally tried doing some laundry and got this error message. Suffice it to say a broken washer after all we were dealing with would have been the final straw but thanks to this video (our movers jammed the drain line almost 3 feet down) we were able to quickly fix the problem and get the machine working. Thanks for sharing this video.
For my IE error code, I had to remove the pressure switch hose and clean it out. I ran hot water through it and blew through the hose. The larger hose it connected to also needed to be drained out and cleaned out.
Thanks for video. Helped me to open cover. Water was ok but still IE code. It was an air pipe measuring the pressure which was disconnected.
Welcome that’s for sharing that I’m glad you were able to fix it
How did you remove the air pipe?
@@سعدالأسمري-ذ7ج I put back the disconnected air pipe. No removal. Air pipe is on top right side
Thank you. It helped a lot. I fixed my machine myself and I saved hundreds in repair bills. 👍
I'm glad I found you :) Thank you for your instructions, I will try some of these out soon :)
Thank you going to try both of these today, I'll let you know if it solved it.
This should be the last step for an IE or 1E error.
1. Check to make sure the draining hose isn't too far down the wall- this creates a siphoning pressure, which drains as your washer fills.. it should be barely inserted into the wall.
2. Check inlet plastic filter for debris/blocking- make sure the water has smooth sailing into the washer
3. Check the Valve on the wall- purchase a meter to check to make sure the water coming out from the HOT VALVE and COLD VALVE is okay and does not need to be replaced. This requires a bucket & turning off the valve for hot & turning off valve for cold, then inserting the meter each and turning valve back on to test.
4. The inlet valve he replaced in the video is the last step for this error. Usually the problem. But 90% of the time it's step one-Pressure Hose.
I just checked the drain hose and that was exactly the problem thank you so much man you saved me from buying a new one/ numerous trips to the laudrymat
@@ryanpappalau1924 So glad I could help Ryan. I had the same issue but it was number 2. My plastic filter was clogged full of rusted particles from my old hoses that have broken off pieces over time. Some people remove the filter as it's really not needed. I just unclogged it and screwed it back in. Very happy I saved you some crazy amount of lucrative plumbing fee. Plumbers love this type of work. Easy fix and bucko bucks for the call.
Thank you sir!
My lg washer machine is giving me that error always.
I have good inlet water pressure, the drain hose is 25cm into a pipe on the wall, (which is half meter high from the floor) not sure if I should reduce those 25cm, to 10cm instead, or less.
It washes ok, but when rinsing , the IE error comes to the screen, had to spin the clothes on "spin" Mode only.
Not sure what's the problem, inlet filter is clean, and water pressure is fine.
Lg instructions says it should be no lower than 61cm. If yours is 50cm and on top of that it's inserted 25, it's probably too low. I'm not an expert though
my filters are a different style at the end of the inlet hoses, the caps come off, but the filter stays in. Taking a break, will try more later. My outlet hose wasn't too far in, so that wasn't it.
Thanks I will check it with my washing machine
Very helpful. I clean the filter the washer seems ok but whilst taking water it suddenly drain it and the IE error display anew. Any reason please!
Thank you for your help
Ours was doing this. So I took mine off cleaned some hard water build up and then poured white vinegar into them and let them sit for About 2 hours later.
I put them back in and for now it's working If it does it again I found the part online and will order a new one.
Thank you very much.
When the water is coming in and coming out at the same time and the error is IE, this vaulve will fix ? Thank you
Thank you for your instruction, but could you please shows us where is the "tap" that we usually forget to open?
hi thanks the tap is the one which you have connected your hot and cold hoses to. Sometimes its not open all the way to give enough water pressure
My front load machine is showing IE error . After cleaning filters,getting same error . I have observed that the tray where we put washing powder ,water supply is coming from one side(left) only. Kindly suggest how to fix that error .
My LG washer keeps getting the IE code
I replaced the intake hoses, cleaned the filters, and cleaned the drain hose. Still code. It codes on wash, on spin, on tub clean too.
Now that I’ve watched your video, I’ll try to check the water intake valves.
Where is it that I’m supposed to order them from?
Thanks
mine did it and it turned out after using it for 2 years the filter on the hot side had accumilated just enough it restricted the water flow. all you need is a towel and a set of flat nosed pliers to pull the filter out to wash it off after you disconnect it. do cold too at the same time.
great good work on that
Like always Mr.Washy, another super video on LG washers. Thanks
Thanks again! Ver y encouraging
@@askmrwashywashy What is the voltage of this water valves, because
with a regulated power supply yo can test the valves without removing
them from the washer. THANKS
@@horaciocastillo1435 220-240volts 6 watts
@@askmrwashywashy Are you sure Washy. Because the input voltage is 120 volts. Unless there is an step up transformer in the circuit. Or you deal with the European models that are made for 220 volts.
Thanks so much for answering my question anyhow. Best regards
@@horaciocastillo1435 yes it’s 220v I think. You right coz I’m in the Australian market
Thanks for advice👍
Replaced cold water inlet valve still has the code ie?
My lg washer machine is giving me that error always.
I have good inlet water pressure, the drain hose is 25cm into a pipe on the wall, (which is half meter high from the floor) not sure if I should reduce those 25cm, to 10cm instead, or less.
It washes ok, but when rinsing , the IE error comes to the screen, had to spin the clothes on "spin" Mode only.
Not sure what's the problem, inlet filter is clean, and water pressure is fine.
@MsNyas open the top cover of the washing machine, and look at the right side , there is a gummy black pipe connecting the water deposit to a device who switch the water inlet on, and off....
Mine was unplugged.
@@Raulperez-yc9de thanks man, you fixed mine.
@@Raulperez-yc9de, fixed mine too, thanks!
Mine gets stuck in spin mode. Hopefully this helps
Please, can you help me? My washing machine receives water well, yet this symbol appears and it is full of water and stops even though I have had it for ten years. What should I do please?
Hi there. It could be an issue with the main board.
So I like to know if it's possible to it can be that the boot the PC board is got a problem because I've tried to change even the the filter even the sensor everything but it's still goes back to the IE error
Thank you for your video. I have an IE error and have replaced the water pressure valve and sometimes the IE error returns. It is not the water pressure. The filters are clean as well. Sometimes it works, sometimes not. Please help.
Which valve did you replace ?
Mine has the same problem. It sometimes gives me the error, and sometimes not. Did you fix it?
@@drunkenmaster389 how did you fix this ? It's happening to me
@@johnmoores1121 same thing is happening to me like it literally will give me the IE code and then I will just restart the cycle and it will wash without giving the code. He just does it randomly the drain is fine. Both valves are fine kind of weird lol
@@matthewjohnson5359 a got rid it waz doing ma head in pal
Hi there @Mr Washy Washy, i'm glad to found a video with the same model of Lg machine. My problem is more profond i think ; when I force the machine to do a rinse it does not stop supplying water to the tank. And fills it to the brim! So the valve doesn't close anymore. Do you think it's a valve problem like in your video or an electronic circuit?
I change bearings replaced cold and hot water valves in washer it will go through wash cycle but when it comes to the rinse cycle it will not advance I stop the washer and put it on rinse and spin cycle it will finish out
thank you , realy i do the same and it work 100%
Welcome glad it helped you
Good afternoon sir please I have check the inlet valve their ok but it's still giving me the same IE Error code
Just saw your very informative video. My machine gives IE error after 4 to 5 minutes. It doesn't consume detergent as well. What could be wrong
might be the inlet valve. you can swap them around and test with the cold valve using the hot valve. do cold only cycle
My machine is with one inlet pipe and so has only one inlet valve. It runs for few minutes as soon as I start the machine and it also takes water on left side of soap tray but then it stops with IE error. I observed that there is very little water flow on right side of soap tray. My machine model is LG Wd-14331 adk. Pl help
@@sqsaad1 check kinked pipe and does it overfill with water ?
My machine run for around 2 minutes and then IE error occurs. What to do
What is the name of the part he replaced? I cannot find the link he mentioned.
Thank you very much it was very helpful video :)
Hey brother I got a lg washer that is still throwing same IE code but I already replaced valves and checked water supply and checked pressure switch hose to see if it was clogged and no issues machine washes pretty much till the end but then code comes on and it won't drain
Try and do a rinse and spin only cycle. Curios to see if the rinse is working if rinse is working Might be a fault with the main board.
Mine does not take detergent as water does not go into the dispense drawer. I've checked the taps and hose, they are ok. Then what could be the problem?
Could be the water valve that’s gone bad. To test it connect the terminal on the cold water valve to the hot one see if that works. Make sure you’ve got power disconnected when you disconnect the valve wiring
My washing machine starts normally and after about 2 min, after the chamber is half full with water, then it shows me this error. I’ve checked everything and even replaced the part, still the same. Any suggestions or should I buy a new one?
Don’t know what else to do
Hi which part did you replace ? Check the pipe to the water level sensor. Make sure it doesn’t have a hole in it. Blow into it too might be some debris stuck in the chamber.
@@askmrwashywashy thanks for the reply. I found it a little before you suggested it. That was it. The washing vibrations, it was unplugged and wasn’t reading properly the water pressure. All good now. Thanks again
@@CryptoHolics90 awesome glad you fixed it
How dobyou know if it really needs to change that valve?
If you checked the water taps to see if open and hoses not linked definitely from experience change the valve and it will solve your issue
Water tap is fine from hose, i'd only notice on the soap despenser the water is only coming out in the side where the fabric softener not on detergent
@@palconadventures is this on a hot wash as well ?
Its only one valve just for the cold
@@palconadventures Yes so you will need to replace it
Please am in Ghana where can I get valve to buy
Hi we need help for lg front load WM3170CW lot of water throw in machine keep spinning. Need change wall sensor where we can buy .??
Thank you
where are you located
Seems like my water is not draining?? Or spinning. The clothes is soaked
That's my problem, as well, I get the IE error code. Pulled out the filters and they really were clean so I put them back in. I had to switch from normal cycle to speed wash, got two complete loads done and then the error message came back and it is leaving heavy wet clothes and some water that hasn't drained. Haven't yet checked the pressure hose. Finger crossed that's going to be the problem. I'm 78, widowed, on SS, cannot afford a motherboard. This washer was given to me when friends moved, they had no problems. Top loader LG less than 2 years old. Back to the laundromat I'm afraid.
i got a smart on and the panel kinda came loose, when wasing it will just turn on and off (not the whole machine just the panel)
im thinking a screw is off then
yeah i checked and one screw is missing...
Did I miss it? Did you run the self test to see which water inlet valve was bad? Any of the water distribution valves can cause an "IE" message.
Yah.. look what I posted.. he jumped to conclusion a bit too soon. A lot of mechanics do this because they see this most often and as the solution this is the usual fix. But majority it's a pressure problem. I would think to replace all like a cars bulbs. You are in there, so might as well.
Thank you so much sir, but sir can u help me with someone that can do it for me 🙏, is over 3months I bought my washing machine.. but since 2days now it's stop bringing out 🌊 water.. it will only turning but my clothes is not washing
Hi since it is still new its covered under warranty. i would first check if the tap is on
Great vid
Thanks mate glad you got some value from it.
My washing machine have water but the ie error atill. Have
Good man
My machine run around two minutes and IE error occrs. Hot to solve this
Please check to make sure the water valve doesn’t keep putting water in the drum
I have a lg wt5680 top load. Kept throwing ie code. After changing the valve ot worked fine the next 2 loads then started again. The inlet filters are clean. If I put it onrinse/spin it does fine. Only on the wash cycles it throws the ie code. I checked the drain tube. What else could it be?
hi from what your saying the main wash valve is faulty . which one did you change ?
@@askmrwashywashy I changed the whole valve assembly. 5 valves in all.
My washing machine is not requesting water why
IE IS WATER OE IS HOSE DE IS LID OF WASHING MACHINE WHAT DOES UE mean
UE means Unbalanced Error th-cam.com/video/0JoqKHi7bl8/w-d-xo.html
What would be the problem. If its always stop. IE
The water valves are not working properly. Follow in the video and it will show you what to do. Make sure the water hose is not twisted and make sure the tap is fully on
@@askmrwashywashy is it possible that i can fix it with my own??
@@m3loveofmylife189 He literally just showed you how.. what is wrong with you?
There is IE error for LG 6.5 kg front load Washing machine and the soap water is fully drained off within 2 or 3 minutes and the IE error is displayed. I have cleaned all the in lets and the drain pipes also. The water is fully suppiled to the clothes, Plz guide me.
hi please check the water level sensor might not be sensing that there is enough water into drum, could be a hole in the pipe that can cause this
Top load
Selang di posisi kanan juga biasa lepas
😍😍😍😍
Less than 2 years old washing machine and I am getting this error without moving in and out hoses..just another cheaply made product like most these days.. just terrible
Sorry to hear that you’re having trouble. If it’s less than two years might still be under warranty so ring up LG they might help repair under warranty
LoL dude....i had high hopes with you starting with the obvious (is the water on). Then you dive bombed to overachiever tech super quick. 90% of IE errors are due to clogged valve filters. No need to remove the top and start taking crap apart. Remove the hose, clean the filter, reinstall. If you find orange sand or little orange resin beads....call the plumber and have your water softener fixed because your problem is the softener. This accounts for MOST IE errors. Now if those are clean and the water flows from the hose into a bucket when turned on....THEN you can take the lid off and replace the valves. C'mon man....
Hi
Wow, talk about long winded videos!!
shockes
Why the gloves?
I work as a heavy diesel tech so most of the times I've got grease and dirt all over my hands and quickly wanna smash out a video so don't wanna put dirt on the camera or customer's washing machine
give us a break Chris. Really?
Dumbest question I have ever seen
Just get to the point! painfully long winded.
talk too much without sense
Could I get the link to purchase the replacement part please? Can't find it on the video. Thanks