The video quality has a lot to be desired but stupid me broke out the older digital SLR for this video while I have a new iPhone in my pocket LOL. I will post more in the near future with Much better video quality and a lot fewer Ummms. Thank you for your comments. 😁
I ended up getting one thanks to your review. I'm really happy with it so far, it's been about a month. I had a WEN but it broke , but all my goodies fit with this one. Thanks for the review!
I have the Bauer 14x20 lathe as well. I added the Wen 24 inch extension bed (34035EX) to it. Fits like a glove. The Wen LA8800 & LA8800EX lathe stand & extension fit as well. I like the WEN stand because of the open design, no wood chips can get caught in and around the motor. If this happens, the motor looses it ability to cool properly. All total, mine now weighs in a little over 200lbs. That includes the Woodriver Steady Rest. My only complaint is when turning objects longer than 30 inches, 1 hp isn't quite enough. A super light touch is required. Overall, I am pleased with the lathe. It is far better than the 10x18 Central Machinery lathe (have that one as well). The 10x18 is in the process of being converted into a polishing system.
I did major comparisons with wen, grizzly, artisan, ryobi, and a couple other's, all basicly the same lathe as the baur for the prices of all were $200 to 1000.00 more money. I did buy the bauer with the stand for the grand total of $706 00. So far, I agree with your total assessment. The addition of the speed control from a low of 45 to 3600rpm plus is great at the touch of a knob & belt. I have also done some slow speed metal machining & added drawer set up to both leg sets. They may get in the way in the future, time will till. All around, good job on this video, agree all the way.
I absolutely love this lathe too. Super quiet and i have turned some things that were significantly heavier than i would recommend and it cranks through it. I also just put the 14in lathe sized grizzly extension bed on and it fits perfectly
Like i said in the video there was nothing out there on this lathe, I felt the need to post one and put in my two cents. thank you for your kind words and happy turning.
I don't do segmented turning and watching the multicolored chips go flying when you started turning was very festive! haha I think I'm getting this lathe. I have one of the smaller delta/rockwell gap beds but the variable speed would make my life so much easier. On your carbide remarks, once you have jigs set up for your gouges, sharpening takes at most 2 minutes then I'm back on the lathe. I don't have any experience with carbide tools yet, but I think I'm going to pick one up.
Just a heads up, I also had issues with the motor running hot on my 10 inch lathe from HF. Turns out the mounting bracket for the motor (The part with the handle for tensioning the belt) was installed incorrectly from the factory. There are three holes drilled in the mount that need to line up with holes on the motor housing to allow proper cooling, but the way it was installed originally blocked those holes. I was able to line up those holes correctly and haven’t had any issues since. I am thinking of upgrading though so thanks for the video!
Some commenters have asked why many, if not most, experienced turners prefer using traditional lathe tools rather than carbide tools. There are two answers to this question. The first is that traditional lathe tools, such as spindle gouges, skews, and bowl gouges, use a 'bevel rubbing cut'. Carbide tools, like traditional scrapers, use a 'scraping cut'. In general, a bevel rubbing cut leaves a much cleaner surface than does a scraping cut. Thus, using traditional tools allows an experienced turner to achieve sharper, cleaner details with less sanding than can be achieved with scraping tools -- carbide tipped or not. The second reason traditional tools are preferred has to do with flexibility. With traditional high-speed steel tools, a turner can quickly and easily change a tool's profile to meet a particular need. For example, I was recently turning a ring holder and was hollowing a small dish shape from which a finial would protrude from the center. None of my spindle gouges would fit into the tight radius of the curve of the bottom of the bowl, and none of my round nosed scrapers fit the curve, either. So, I took my smallest round nosed scraper and gave it a smaller, tighter profile. In less than 5 minutes at the bench grinder, I had the perfect tool for the job. You can't do that with carbide tools. If you don't have the right-sized carbide cutter, you have three options: buy another tool, change your design, or spend a lot of time sanding to get the shape you want. None of this means carbide tools are not a worthy addition to a turner's arsenal. I have and use carbide tools regularly. They just work better for some things than for others. Bottom line: You can make the same projects with carbide and traditional tools. With carbide tools you'll spend more time sanding (and your details might not be as crisp as a result). With traditional tools, you'll spend more time sharpening.
This seems like a great option for newer turners, or price conscious intermediate turners. I bought a Laguna 12x16 a few years ago and I like it very much. If this was around then, I'm sure I would have given it a good look.
Hey Dan thanks for the review. I was going to upgrade my 4 year old 6 x 30 harbor freight (Central Machine) lathe. Are you still happy with it. I think I will get this one.
Enjoyed the video, I have a question.... I've never used a lathe and wondered, could you use this if it sat on a harbor freight cart, or would you be pushing it around. I see you use it turning counterclockwise and dont know how much " pushing " pressure you use to possibly push the cart. Thanks in advance. Greg in Michigan
I didn't hear any negatives about this thing because of the wiring that's just something that you want done better for you and the lubrication that just sounds like regular maintenance work
I've been wanting to get me one and this is probably the one I'm going to get for harbor freight also you pay that 2 year warranty fee and you never have to worry about it just turn it back in and get a new one for free but I'm going to have to build my own little maybe 8 ft by 8 ft building because they make a mess
Absolutely happy with it. I have done 25 - 30 projects with this without any problems, still works like new. I will be posting more videos using a much better camera and sound.
Thank you for posting! Looking at this lathe I make duck calls and need to drill a 5/8in. Hole in my barrels. Is the tail stock capable and robust enough? Thank you
Type this into an Amazon search (Live Tailstock Chuck Adapter to 1" x 8tpi Thread with #2 Morse Taper Mount) and you will find the adaptor for your tailstock. Happy turning.
I have purchased two different sets and a few extra handles and they are about the same. I would recommend getting a set with straight handles and when you need new inserts get quality inserts. the inserts are what's important.
I have had the same one from Axminster (GB) since 2020. The electronic module has defects. I had to change it after 18 months. It seems that this is a recurring failure on this model. Otherwise, nothing to say. This wood lathe works very well. I have already made 13/5 salad bowls on it.
Thank you for this information, I was unaware of this. This is why I made this video, to get some information on this product out there so people can make an informed decision before buying. Once again Thank you.
Good video brother. Keep it going! I’d love to see more turning.
The video quality has a lot to be desired but stupid me broke out the older digital SLR for this video while I have a new iPhone in my pocket LOL. I will post more in the near future with Much better video quality and a lot fewer Ummms. Thank you for your comments. 😁
Great video. Would love to see more of your work. Maybe some tutorials. Again great job.
I ended up getting one thanks to your review. I'm really happy with it so far, it's been about a month. I had a WEN but it broke , but all my goodies fit with this one. Thanks for the review!
@watupwitu ,, if you put heavyweight roller caster on it , put back up 12mm nuts inside the frame because the welded nuts can break.
@@RonMc-k2k:
wait…what?
I have the Bauer 14x20 lathe as well. I added the Wen 24 inch extension bed (34035EX) to it. Fits like a glove. The Wen LA8800 & LA8800EX lathe stand & extension fit as well. I like the WEN stand because of the open design, no wood chips can get caught in and around the motor. If this happens, the motor looses it ability to cool properly. All total, mine now weighs in a little over 200lbs. That includes the Woodriver Steady Rest. My only complaint is when turning objects longer than 30 inches, 1 hp isn't quite enough. A super light touch is required. Overall, I am pleased with the lathe. It is far better than the 10x18 Central Machinery lathe (have that one as well). The 10x18 is in the process of being converted into a polishing system.
Good morning David, one question: how to adapt the plate to the tailstock axis?
Thank you for sharing. Nice lathe setup for your segmentation work
I did major comparisons with wen, grizzly, artisan, ryobi, and a couple other's, all basicly the same lathe as the baur for the prices of all were $200 to 1000.00 more money. I did buy the bauer with the stand for the grand total of $706 00. So far, I agree with your total assessment. The addition of the speed control from a low of 45 to 3600rpm plus is great at the touch of a knob & belt. I have also done some slow speed metal machining & added drawer set up to both leg sets. They may get in the way in the future, time will till. All around, good job on this video, agree all the way.
Very helpful. Congrats on your first video!
I think it’s a great looking lathe. Nice review.
I absolutely love this lathe too. Super quiet and i have turned some things that were significantly heavier than i would recommend and it cranks through it.
I also just put the 14in lathe sized grizzly extension bed on and it fits perfectly
I believe the 14" WEN lathe bed extension fits this lathe also.
I'm looking for a new lathe. Thank you for the review. Yes it is extremely quiet. I guess I know what my next lathe will be.
Hope you enjoy it!
I got this lathe a month ago and I am loving it. Good review vid man.
Like i said in the video there was nothing out there on this lathe, I felt the need to post one and put in my two cents. thank you for your kind words and happy turning.
I don't do segmented turning and watching the multicolored chips go flying when you started turning was very festive! haha I think I'm getting this lathe. I have one of the smaller delta/rockwell gap beds but the variable speed would make my life so much easier.
On your carbide remarks, once you have jigs set up for your gouges, sharpening takes at most 2 minutes then I'm back on the lathe. I don't have any experience with carbide tools yet, but I think I'm going to pick one up.
Thank you so much I’ve been waiting for a good review on this lathe, looks very close to the rikon 10x18, with the 1 hp motor and reverse, very cool
Thank you, I am going over to HF and take a look at this one.
Just a heads up, I also had issues with the motor running hot on my 10 inch lathe from HF. Turns out the mounting bracket for the motor (The part with the handle for tensioning the belt) was installed incorrectly from the factory. There are three holes drilled in the mount that need to line up with holes on the motor housing to allow proper cooling, but the way it was installed originally blocked those holes. I was able to line up those holes correctly and haven’t had any issues since.
I am thinking of upgrading though so thanks for the video!
Some commenters have asked why many, if not most, experienced turners prefer using traditional lathe tools rather than carbide tools. There are two answers to this question. The first is that traditional lathe tools, such as spindle gouges, skews, and bowl gouges, use a 'bevel rubbing cut'. Carbide tools, like traditional scrapers, use a 'scraping cut'. In general, a bevel rubbing cut leaves a much cleaner surface than does a scraping cut. Thus, using traditional tools allows an experienced turner to achieve sharper, cleaner details with less sanding than can be achieved with scraping tools -- carbide tipped or not.
The second reason traditional tools are preferred has to do with flexibility. With traditional high-speed steel tools, a turner can quickly and easily change a tool's profile to meet a particular need. For example, I was recently turning a ring holder and was hollowing a small dish shape from which a finial would protrude from the center. None of my spindle gouges would fit into the tight radius of the curve of the bottom of the bowl, and none of my round nosed scrapers fit the curve, either. So, I took my smallest round nosed scraper and gave it a smaller, tighter profile. In less than 5 minutes at the bench grinder, I had the perfect tool for the job. You can't do that with carbide tools. If you don't have the right-sized carbide cutter, you have three options: buy another tool, change your design, or spend a lot of time sanding to get the shape you want.
None of this means carbide tools are not a worthy addition to a turner's arsenal. I have and use carbide tools regularly. They just work better for some things than for others. Bottom line: You can make the same projects with carbide and traditional tools. With carbide tools you'll spend more time sanding (and your details might not be as crisp as a result). With traditional tools, you'll spend more time sharpening.
This seems like a great option for newer turners, or price conscious intermediate turners. I bought a Laguna 12x16 a few years ago and I like it very much. If this was around then, I'm sure I would have given it a good look.
Great video and details! Thanks for the review!
Glad it was helpful!
Will the tail stock take a drill chuck
Thanks for the review. Ill be getting this one
Thanks!
Hey Dan thanks for the review. I was going to upgrade my 4 year old 6 x 30 harbor freight (Central Machine) lathe. Are you still happy with it. I think I will get this one.
Great review 🙏
Enjoyed the video, I have a question....
I've never used a lathe and wondered, could you use this if it sat on a harbor freight cart, or would you be pushing it around. I see you use it turning counterclockwise and dont know how much " pushing " pressure you use to possibly push the cart.
Thanks in advance.
Greg in Michigan
Hi Dan. Thanks for the video. I’ve been looking to buy a lathe. Can you buy an extension for this one?
I didn't hear any negatives about this thing because of the wiring that's just something that you want done better for you and the lubrication that just sounds like regular maintenance work
I've been wanting to get me one and this is probably the one I'm going to get for harbor freight also you pay that 2 year warranty fee and you never have to worry about it just turn it back in and get a new one for free but I'm going to have to build my own little maybe 8 ft by 8 ft building because they make a mess
I have been considering this lathe are you still happy with it
Since this review ?
Absolutely happy with it. I have done 25 - 30 projects with this without any problems, still works like new. I will be posting more videos using a much better camera and sound.
@ awesome thank you for your feedback and videos 👍
Just subbed you
Good review on this lathe. Thanks I have had my eye on this one also. What lathe tools are you using?
@@kevinosterude7239 ,, really to main to go over all.
Thank you for posting! Looking at this lathe I make duck calls and need to drill a 5/8in. Hole in my barrels. Is the tail stock capable and robust enough? Thank you
Definitely. I drill 1 7/8” Forster holes with no problem. Just take it slow and clear my chips!😂
Good morning, one question: how to adapt the plate to the tailstock axis?
Type this into an Amazon search (Live Tailstock Chuck Adapter to 1" x 8tpi Thread with #2 Morse Taper Mount) and you will find the adaptor for your tailstock. Happy turning.
nice! I don't know also why pros don't like the carbide tools.... Where did you get yours? I can't find any affordable
I paid $170 for mine. After you buy a three piece set, you will not think they are unaffordable. Soooooo nice to use!
What brand carbide tools? Please advise.
I have purchased two different sets and a few extra handles and they are about the same. I would recommend getting a set with straight handles and when you need new inserts get quality inserts. the inserts are what's important.
Nice review Mr Reed!
Thank you kindly but you are biased. LOL
I have had the same one from Axminster (GB) since 2020. The electronic module has defects. I had to change it after 18 months. It seems that this is a recurring failure on this model. Otherwise, nothing to say. This wood lathe works very well. I have already made 13/5 salad bowls on it.
Thank you for this information, I was unaware of this. This is why I made this video, to get some information on this product out there so people can make an informed decision before buying. Once again Thank you.
This looks identical, except for color, to the Wen 14 x 20 Midi.
Hey! I know where this shop is!
Worth the $600?
Dads birthday.
I think so.
@@danreed1525found a great sale, $530.
Not too long ago you guys were like, Harbor Freight it's cheap, and their tools are crap. Look at y'all trendy buzzards...