Thank you so much for actually making a video on the SGW Bypass. I only wish the video kind of showed my how to install it because I read the instructions and they're so much harder on the stelvio than the giulia!
Nice, the pictorial instructions didn't really give enough context for where this thing was, makes sense not too bad. The alfa service manual has you taking apart half the car haha. What the dealers charge for maintenance on these cars is criminal for how little actually needs done. simple enough for the home mechanic.
I’m confused.. Do you need the sgw bypass module to even use multiecuscan on the 2018+ models? You can’t just plug a laptop with the software on it into the stock OBD port and run diagnostics? You have to use the bypass module plug with the laptop to use diagnostics? Help?
For Alfa Romeo Giulia and Stelvio with the manufacture date of February 2018 and on you need an extra module is called a SGW bypass plug. New model, and fully unlocked features! Beginning with model years 02/2018 and above Alfa Romeo vehicles are equipped with a new device called a security gateway module. The purpose of this module is to prevent CAN bus hacking over the G or LTE network. This Bypass plug allows you to bypass this module. This unit is required to access the Body control module, infotainment system, and the ECM. If you got a check engine and want to pull the codes then any OBD2 scanner can do that.
If you’re trying to pull codes then no but if you’re trying to access any module like any oil resets and your vehicle is after February 2018 then you do
I have a 2019 Giulia it has the fuel cut off I tried the blinker process but didn’t work I got the Zurich scanner and got the autoauth account and either I’m not doing it right or idk how to reset it . Any suggestions ? Do I need to the same process u did ?
Appreciate this so much, such a small community for us Giulia DIY people but these videos are so helpful. Is there a way to connect to Multiecuscan with a bluetooth OBD device or does it have to be wired? Also I'm confused about all the different colored cables. Do I need the grey and blue cables if I'm just trying to reset service intervals and check basic engine codes?
Hello and thank you for watching. Multiecuscan does offer Bluetooth. Multiecuscan is also available on App Store for iPhone/iPad devices! Multiecuscan for iOS works with WiFi ELM327, CANtieCAR v4.x/v5.x, OBDLink MX WiFi, OBDLink MX+ Bluetooth interfaces.
Hey! Looking to install race mode on 2019 but i need to get past security. Do you leave that swg module in the car? Or do you put the other one back after? & if you take it out & put the other one back, do you only plug it in whenever you need to use multiecuscan?
& do you unplug the car from battery before you install the swg module? I see the door open but nothing on the dash. & if you take it off if it after your done do you take it off after you close out of multiecuscan & are finished?
@@RonDIYMods Thanks! Not sure if you saw this part. Do you unplug the car from battery before you install the swg module? I see the door open but nothing on the dash.
Thank you for watching all you need is the Diagnostics ELM to connect to your laptop. The other adapters are needed for different modules but for this and oil change all you need is the diagnostic ELM. Check out this video th-cam.com/video/MD7LqasnmzA/w-d-xo.htmlsi=xDMTBXodFr2ygOkN
For Alfa Romeo Giulia and Stelvio with the manufacture date of February 2018 and on you need an extra module is called a SGW bypass plug. New model, and fully unlocked features! Beginning with model years 02/2018 and above Alfa Romeo vehicles are equipped with a new device called a security gateway module. The purpose of this module is to prevent CAN bus hacking over the G or LTE network. This Bypass plug allows you to bypass this module. This unit is required to access the Body control module, infotainment system, and the ECM.
@@zwan69 yes I agree. As I am showing the installation on the Giulia. But both Stelvio and Giulia require the SGW Bypass to work with the multiECUscan to work on 2018 and on models.
Thank you so much for actually making a video on the SGW Bypass. I only wish the video kind of showed my how to install it because I read the instructions and they're so much harder on the stelvio than the giulia!
Yes the Stelvio and Giulia are different but same concept.
Great helpful vid!!! Got it unplugged after a few attempts! Much appreciated!
Thank you for watching. I’m glad my video was able to help you.
Hi, does we have to disconnect battery before unplugg original cables ?
Hello. No
Thanks for the how-to! Are the cable extensions required? Seems like you could have plugged in the SGW bypass without them.
That is correct. Cables are not required. It just makes it a bit easier but you can plug a straight to SGW.
Nice, the pictorial instructions didn't really give enough context for where this thing was, makes sense not too bad. The alfa service manual has you taking apart half the car haha. What the dealers charge for maintenance on these cars is criminal for how little actually needs done. simple enough for the home mechanic.
Yes. This is the purpose of my videos to help people save money and show them that most of the time no need to take it to the dealer.
I’m confused.. Do you need the sgw bypass module to even use multiecuscan on the 2018+ models? You can’t just plug a laptop with the software on it into the stock OBD port and run diagnostics? You have to use the bypass module plug with the laptop to use diagnostics? Help?
For Alfa Romeo Giulia and Stelvio with the manufacture date of February 2018 and on you need an extra module is called a SGW bypass plug. New model, and fully unlocked features! Beginning with model years 02/2018 and above Alfa Romeo vehicles are equipped with a new device called a security gateway module. The purpose of this module is to prevent CAN bus hacking over the G or LTE network. This Bypass plug allows you to bypass this module. This unit is required to access the Body control module, infotainment system, and the ECM. If you got a check engine and want to pull the codes then any OBD2 scanner can do that.
@@RonDIYMods Okay, so I don’t need this piece to use multiecuscan software with a laptop?
If you’re trying to pull codes then no but if you’re trying to access any module like any oil resets and your vehicle is after February 2018 then you do
On Stelvio ist a little bit more complicated. SGW module ist behind steering wheel column. You need pations and small hands
I agree
the bypass have to be remove after the procedure o you leve there and drive normaly?
You can leave it and drive normally.
I have a 2019 Giulia it has the fuel cut off I tried the blinker process but didn’t work I got the Zurich scanner and got the autoauth account and either I’m not doing it right or idk how to reset it . Any suggestions ? Do I need to the same process u did ?
I believe your going to need the bypass module in order to communicate with the car.
Appreciate this so much, such a small community for us Giulia DIY people but these videos are so helpful. Is there a way to connect to Multiecuscan with a bluetooth OBD device or does it have to be wired? Also I'm confused about all the different colored cables. Do I need the grey and blue cables if I'm just trying to reset service intervals and check basic engine codes?
Hello and thank you for watching. Multiecuscan does offer Bluetooth. Multiecuscan is also available on App Store for iPhone/iPad devices!
Multiecuscan for iOS works with WiFi ELM327, CANtieCAR v4.x/v5.x, OBDLink MX WiFi, OBDLink MX+ Bluetooth interfaces.
Hey! Looking to install race mode on 2019 but i need to get past security. Do you leave that swg module in the car? Or do you put the other one back after? & if you take it out & put the other one back, do you only plug it in whenever you need to use multiecuscan?
& do you unplug the car from battery before you install the swg module? I see the door open but nothing on the dash. & if you take it off if it after your done do you take it off after you close out of multiecuscan & are finished?
Yes. You can leave it in if you want. If not then plug in when ever you need to use Multiecuscan. Once you unplug one plug, the other one.
@@RonDIYMods Thanks! Not sure if you saw this part. Do you unplug the car from battery before you install the swg module? I see the door open but nothing on the dash.
@@RonDIYMods So you leave the swg module in?
@@marz11004 no need to remove terminal from battery
What type of cable do you connect from your computer to the car, red, blue or gray?
Thank you for watching all you need is the Diagnostics ELM to connect to your laptop. The other adapters are needed for different modules but for this and oil change all you need is the diagnostic ELM. Check out this video th-cam.com/video/MD7LqasnmzA/w-d-xo.htmlsi=xDMTBXodFr2ygOkN
Stupid Q. By having thr mes only can't the service be rest?
For Alfa Romeo Giulia and Stelvio with the manufacture date of February 2018 and on you need an extra module is called a SGW bypass plug. New model, and fully unlocked features! Beginning with model years 02/2018 and above Alfa Romeo vehicles are equipped with a new device called a security gateway module. The purpose of this module is to prevent CAN bus hacking over the G or LTE network. This Bypass plug allows you to bypass this module. This unit is required to access the Body control module, infotainment system, and the ECM.
does the battery have to be disconnected?
No
Hey! Are you going to do the interior light install on the Stelvio? Looking to do mine soon!
Yes I just order a kit I though would work great for it. I’ll work on it soon and have a video coming out soon.
Thanks!!
You’re welcome and thank you for watching
What year is this?
2020
How much do you pay for multi scan ?
I paid like $55 for the program key.
Where did you get the bypass cable?!
Link is on the description of the video.
Hey bro I tried the blinker method and now my turn single on driver side won’t work any help ??
In dash it doesn’t not indicate rapidly or have a light on it’s all as normal and it just stopped …
I haven’t done that method. I don’t have no clue how to fix it. Try doing the method again maybe you with reactivate if you do it again.
@@RonDIYMods I have but nothing :(
歐規車也可以用嗎？
YES, I believe so.
Nix Stelvio!!!
????
@@RonDIYMods With the Stelvio, the plug is in a completely different place and is not so easy to reach!
@@zwan69 yes I agree. As I am showing the installation on the Giulia. But both Stelvio and Giulia require the SGW Bypass to work with the multiECUscan to work on 2018 and on models.
If you can show it on a stelvio that will be great 👍
After 9 time servie no more infos about km days can i see day and km aggain