The reason they tell you to put the hole 1 cm above is just because the layout they provide does not account for the fact that the mirror will slide down once on the mirror catchers. Bad design of the layout: all they had to do was to move those markings accordingly,, but i guess they were already printed! For an easier solution, just put the layout 1 cm above the intended height of the mirror and drill in that hole..
Thanks a lot!! question: I wanna buy many of these and install them next to each other for a dance studio. do you think I can change the two hooks on the side and put them up so they hold the mirror like the ones on the bottom !?
If the mirror is vertical, you have to do two holes on the top and two on the bottom. There’s a cardboard guide that comes with the mirror that will help. I don’t remember specifically where the holes go for horizontal but the directions would say
You’re welcome! The cap and hook came with the mirror. I don’t have a link for the nails bc we found nails that were laying around in the toolbox 😕 I think any nail that is 2.5 inches or longer would work for this
Command strips will definitely get the job done. This mirror is very light. Just make sure you get the right ones bc some of them can only hold a certain amount of pounds. I’d recommend ones that can hold 15lbs or more.
I bought this mirror but want to screw it onto my wardrobe sliding doors instead but not too sure if it will hold but they are quite thick doors. Any advice?
The mirror is pretty light. I’m pretty sure your wardrobe can handle it. You might be able to install it the same way we did in the video too. If not I’d recommend some strong command strips
If your screw is going into a 2x4 on the other side of the drywall then you don’t need plugs. Plugs are more for when you want to hang something where your screw won’t catch a “stud” (2x4).
![[FINALE] มีคนคิดแค้นลักพาตัวเด็กไป🔪หญิงชราใช้ชีวิตตัวเองเข้าแลก👩🦳 #โลกการละคร](http://i.ytimg.com/vi/C_BPHPoZFOg/mqdefault.jpg)
Thank you so much! This helped a lot, beecausr the official manual is a bit hard to read
You’re welcome! 😁
Literally the instructions are shit
Thank you, couldn't make sense of the ikea instructions.
You’re welcome! 😄
The reason they tell you to put the hole 1 cm above is just because the layout they provide does not account for the fact that the mirror will slide down once on the mirror catchers. Bad design of the layout: all they had to do was to move those markings accordingly,, but i guess they were already printed! For an easier solution, just put the layout 1 cm above the intended height of the mirror and drill in that hole..
That’s so helpful!! Thank you!!
Lol this was both helpful and very funny. Thank you!
Aww thanks! And you're welcome!
Thank you for this video 😫 i was super struggeling with it but now i understand it !!! 🎉
You’re welcome! 😄
Really appreciate this. I have installing mirror but this looked so simple.
No problem!
Loved this tutorial! Specially the twerking part lol! Thank you!
😂😂😂 thank you!
Thank you. Just bought one and this is what I needed.
Thanks for the tutorial. I couldn't figure out the manual 😩😩 Cheers !
You’re welcome! 😄
Thanks a lot!! question: I wanna buy many of these and install them next to each other for a dance studio. do you think I can change the two hooks on the side and put them up so they hold the mirror like the ones on the bottom !?
Yes! I think that would work fine
I just brought 2 for my small gym area, going to do the same thing!
@@mz_martina I bought 4, worked for me but u gotta be so precise with the measurement! Good luck
@@salmasaad198 i ended up getting a j bar from lowes and regular mirror clips!🤦
Liked this video before I even got to the tutorial because of the twerk lmao cracked me up girl
Lmao thank you!
This video was helpful and cute ty!!
No thank you! 😄
Hi, can this be used as standing mirror? Will it fall?
Great teaching vid...funny 🤭and definitely helpful
Thank you!
I am moving and bringing the mirror with, so I don’t have the template anymore. Do you know the distance between the bottom clips and the side clips?
I've got the same problem, did you find out about the measurements??
Thank you so much. I have a question: do you have to do the other hole only in the bottom of the mirror or either on the top?
If the mirror is vertical, you have to do two holes on the top and two on the bottom. There’s a cardboard guide that comes with the mirror that will help. I don’t remember specifically where the holes go for horizontal but the directions would say
@@Jaybeccaofficial thanks💖💖
Hey, thanks for the video, do you think the drill is necessary to screw the nails to the wall or I can do it by hand?? I don't have a drill
The drill isn’t necessary
Thank you, that was really helpful!
You’re welcome!
thank you 🥰 this help me soo good ❤️
You're welcome!
Wow this is so useful - thank you! Would you mind linking to the nail/cap/hook combo?
You’re welcome! The cap and hook came with the mirror. I don’t have a link for the nails bc we found nails that were laying around in the toolbox 😕 I think any nail that is 2.5 inches or longer would work for this
This was so helpful!!!! Thank you!
You’re welcome!
I was wondering if it was possible to use command strips or hooks etc to hang this mirror up? Only because I’m a student and can’t use nails!
Command strips will definitely get the job done. This mirror is very light. Just make sure you get the right ones bc some of them can only hold a certain amount of pounds. I’d recommend ones that can hold 15lbs or more.
I bought this mirror but want to screw it onto my wardrobe sliding doors instead but not too sure if it will hold but they are quite thick doors. Any advice?
The mirror is pretty light. I’m pretty sure your wardrobe can handle it. You might be able to install it the same way we did in the video too. If not I’d recommend some strong command strips
@@Jaybeccaofficial thank you
Did u have to stub-finder?
Question; is it best to use plugs in a regular wall or should only screws do?
The mirror is pretty light. I think screws alone would be fine
If your screw is going into a 2x4 on the other side of the drywall then you don’t need plugs. Plugs are more for when you want to hang something where your screw won’t catch a “stud” (2x4).
Please tell me the number that i should look for buying the nails. There are so many similar ones
I think anything above 1 inch screws should do the trick
Thank u we was struggling lol
Thank you so much for your help .
You’re welcome!
Thank you so much 😊
You’re welcome!
Really helpful, thanks
You’re welcome 😊
Bruh. I wish I knew they didn’t come with screws before I went home 🤦♂️
IKEA is notorious for that 😂
Hahaha cute 👻 I love my job 😊
😂😂😂
Thanks so much. I couldn't understand the manual provided.
You’re welcome!
I want to purchase this, does it leave a hole on wall ?
Yes it does if you follow the directions. You can probably use command strips instead if you want to avoid holes in your wall
How tf y’all get the mountain clips out? Lmao I cannot get them out for the life of me they’re like stuck in the plastic
Honestlyyyy you gotta find a way 😂 we just pushed it out with force. Knowing Ikea, there are probably some that just wont come out 😬
Thanks for sharing 💪🏻
Thanks for that guys
You’re welcome!
I couldn’t get the round grey thing out from the plastic holder
Yea it’s super hard to get out. Maybe try running it under hot water or putting some sort of lubricant inside of it to make it slip out
We messaged ikea and they sent them sepereated
Thank you!
Yw!
I came here because I didn't understand the "no drilling" drawing in the instructions lol
😂😂 I hope this helped
is it 48x120?
No it’s 18 7/8x47 1/4” those measurements are from the site
Whts the height Nd width?
The website says 18 7/8x 47 1/4
Im so pissed, the store guy advised me to get this because its glued on, now i have to find a screw
What I want to know is the relationship between the two of you? Siblings? Lovers? 😅
Those are screws, not nails, and the instructions say not to use that type of head type.
It worked for me 🤷🏾♀️
thank you
You’re welcome!
Price update the mirror is $18 dollars
Thank you!
Thanks! The manual sucks
You’re welcome!
Хороший зад
Thank you!