F22 F2X BMW M235i Tail Light Malfunction Repair
ฝัง
- เผยแพร่เมื่อ 23 ส.ค. 2024
- Have you gotten the famed and dreaded taillight malfunction on your F2X 2 Series BMW? This video is for you! I go over the steps and share the part #'s used to fix the issue like OEM. Subscribe for more ► / turboshotincredible
Tail Lamp Assembly w/ ground BMW # : 63217370291
LEFT SIDE Tail Lamp Assembly : amzn.to/3coXGBB
Tail Lamp Harness Repair Kit BMW # : 61122448168
Get 15% off merch to support the build ► teechip.com/st...
Get 25% off your auto accessories here & support the build ► gearpiston.com...
The BEST Shop lights for under $50 ► amzn.to/356m4zS
Our Amazon Store ► www.amazon.com...
►Facebook: turboshotincredible
►Instagram: turboshotincredible
►Twitter : tsilovesspeed
The 500hp Budget Build : Project Runway Racer?
www.youtube.co....
The 500hp Budget Build : Part 6 - NEW BOTTOM END PARTS
www.youtube.co....
FIRST IMPRESSIONS AFTER TUNE |6.0 Trans Am Build EP:15
www.youtube.co....
ALUMINUM VS IRON - LS Engine Weight Comparison
www.youtube.co....
YOU NEED THIS IF YOU'RE BUILDING AN LS ENGINE ON A BUDGET
www.youtube.co....
Subscribe for more great automotive videos!
/ turboshotin. .
Made the mistake of trying lights before putting the bulb holder back in place !!! took me 10 mins to realise it earths onto terminals inside the lamp!! Never seen this before LOL Thank you for the vid pal 😂😂
Thanks mate, made changing the bulb a breeze. It’s a 10mm fur whoever’s wondering
Thanks! So I swapped the right side, but the brake lights are dim, and the parking lights do not work. Any ideas?
I use rubber gloves to pull it out, it saves it from chippings etc.
Did the same mistake with the battery screw on the connector, now I can’t tight up my negative connector in the battery
All in all this was a fairly straightforward and simple repair. What other types on content would you all like to see with this car?
Great video. Looks like you're the only one who has made one about this harness. I'm confused as to were the 2 brown wires where connected. I know 1 was on the plug. Where is the other attached?
Thank you! One side goes to the plug, and the other goes to the updated taillight assembly. There's an added spot there for it. It was hard to film since I needed both hands and didn't have a tripod with me
Thanks for the part number!
The European version looks nothing like this. From the outside, yes, but it's equipped with LEDs, not old-scool bulbs and you can NOT take it apart. It's glued together on top of the 8-10 screws. You might get away with heating it in an oven to make the goo-glue soft, but I opted not to. As you may understand, the EU/LED version has the same issue (indicator lights).
That would be the late model LCI version for us in the states
I recently performed this repair on a 2016 228i. The hardest part was removing the bulb assembly, and snapping the new one back in place which was very tight. After it was completed, the reverse function did not work. Back to the drawing board, and thanks for the great post!
Totally agree, that part was definitely difficult, which is why it wasn't recorded, needed both hands. Sorry to hear about your reverse light. Maybe another wire came loose?
@@TurboShotIncredible Hopefully. I’m guessing I’ll have to remove the reverse wire only and reinstall it. Does it make a difference if the pin connector is upside down? And I’m having trouble locating a wire schematic for the reverse wire only
I would think so, yes. Definitely want everything facing the way it was from factory
@@keithp115 Did you get it find out why the reverse light wasn’t working? I did the same procedure and now reverse light not working!
@@ashinmathew99 I haven’t as of yet. Been recovering from back surgery. I believe Turbo Shot is correct. Once recovered, I will reverse the pin and see if that corrects the issue.
Thanks for the help! Greetings from upstate NY.
Thanks this is helpful. My 2019 M2 started giving me rear lamp error. Unfortunately my warranty is done. Bmw should do a recall on this. Everyone I know that has a m2 has this light issue. I search the wiring part number and it says it’s for a n55 M2. Mine has the S55. Need to check if I have the update already?
Check your vin / manufacturer date to see if your car is LCI. It should be. If it is, it'll require slightly different harness and repair procedure.
@@TurboShotIncredible yes mine is the LCI. How do I find the repair schedule and updated part for my car?
Check out this post :
www.2addicts.com/forums/showpost.php?p=26633395
Same on m240i. The led lights don't seem to have a repair kit, unless anyone can correct me on that.
Did you buy just the holder or the holder and tail light repair kit?
Hi, thanks for the video. Do you have a link for the crimping tool?
Thanks dawg, this helped a lot
No matter how much I tried, the connector would not come off. The white tab was at the highest top position. Is there some trick here? Without that connector off, I am unable to figure out if its is a harness issue or a corroded connector issue..
Great video! Thanks pal
Thank you!
how you crimp the pins, I haven't seen a video of anyone describing the crimping procedures
Since I was on my phone with no tripod at the time, wasn't able to effectively film that part since I needed both hands. Very crucial part, it is simple though. Right above the part where you break the terminal off its supporting bracket, there is a section that looks like [___] that then leads into the terminal end. You are simply crimping or folding that flat part into itself, to lock the wire in place. It should look like the center of an open book once crimped together. I can't post photos here but, hope that helps! @0:11 you can see the folded part Im talking about right about the green rubber gromet.
Put some tape on the lense and use it to tug light out
Thank you 🙏
You're welcome, and thank you!
How much did this whole assembly cost you including parts.
I’m being quoted 500 to replace it because it’s cracked(glass shield) and the bulbs are fine but it’s all in one.
Trying to see if it’ll come out cheaper to purchase the part and DIY
When I looked for the complete assembly, it was around $300 for the part alone. If you add in general dealership labor of 150/hour, plus tax, I can see how they got you a quote $500. There are links in the description of the video with prices for the parts used here.
Nice video
Thank you!
Where does that ground extra wire come from?
The wiring kit. Links in description
Do you have the link for the assembly ?
I have one for the left side amzn.to/3coXGBB
how this happen?
Manufacturer design flaw
Same Happend to m3 yesterday, my 116 is 10 years old. So is this problem normal ?
Yea, it's a known bmw issue with the f chassis
will replacing the whole tail light fix this issue? sorry guys don't know much about it.
No! It's an issue with the wiring harness it self.
what do you do with the extra brown ground cable?
It is not extra, that is a secondary ground from the lamp assembly that goes back to the connecting harness.
You splice into the existing ground to create 2 ground points.
@@TurboShotIncredible good to explain since you didn't show that splice in the video and can't seem to find the procedure anywhere. Ground is Brown, Right? I have a 2016 m235xi with 26k km, and the right tail light just blew. Gonna get both sides parts just in case they get discontinued.
Ground is brown, correct. I didn't show that part as i was filming on my phone with no mount/ tripod and needed both hands