Electrical Engineer here. You need to isolate the speaker from the 12V line. Remove the inductor (labeled as coil). Now connect the 12V directly to the transistors instead of through the speaker. Put the speaker in parallel with the transistors, one side to the 12V line and the other to ground. Add a large capacitor between the speaker and the 12V rail with (-) side to the speaker. This should isolate the speaker from the 12V, preventing it from damage. It should also make the audio sound a bit cleaner. Improving on this: Calculate a base input voltage offset to keep transistors in active mode and add a resistor from base pins to ground. It'll reduce distortion.
In my opinion, best he can do is to use two of these 13007 as push-pull topology, not as "quasi-darlington" single ended. It present topology it's easier to get transistors fully saturated, which causes distortion. Second thing is that single ended amps (A class) have less efficiency than push-pull amps (AB class). On the other hand, testing bass speaker in "free air" conditions is not a good idea. Even a weaker amp can provide some bass if the speaker cabinet is calculated correctly. Enclosure makes at least half of job in providing bass from the speaker. And the last thing. Wanna see speaker bouncing? Use a real woofer speaker, not noname like this. This magnet looks really tiny, and suspensions of this speaker can be too hard :) Maybe Eminence Lab12?
@@MichaelBeeny said, "This guy is an idiot, you NEVER pass DC through the speaker, but he always does!!" Bit of a harsh way for you to offer your constructive criticism, isn't it Michael?
This is a Common Emitter design with Collector Feedback. The only reason I can see why you would find the need to put the 3 transistors in parallel is to handle larger currents for stable load lines effects (each transistors can handle up to 8 A, 80W, and 400V). Also since these are switching transistors, they are not the best amplifiers. Nice project. I would suggest that you use these transistors in Darlington configuration to get higher hfe values.
I need your knowledge lol... Because i have no idea what your alien language is... And somehow i ended up turning a simple 10 watt computer speaker amplifier into a stable 350 watt setup... Lucky i guess, teach me your ways lol
@jamdvx Increasing the input to too high a level will cause distortion. The standard for input levels to transistor amplifier preamp like this is about 1 Vpp or 1 volt peak to peak.
The comments section is full of self appointed experts. Lads, he's not aiming for hifi here, he's just showing you a fun little circuit with a few old parts.
well if these people want to keep using the titles that they do then make literally the same exact thing so many other youtubers have done using the same bs titles then they can expect the same kind of criticism
@@paulzedx636ninja7 Maybe the project is cool, but when some young person with not so much knowlege try to do it, and burn down its audio source (phone maybe) and speaker (transistor short circuit), that video is becoming a very bad way to learn electronics. This circuit is high ineffective and in some situations its could be even dangerous.
You could literally use the exact same parts and make something that sounds good , if you build it correctly and not just slap stuff in the wrong places. Never put DC through a speaker. Efen just using an inductor in the collector would have worked better, look up inductor class A amps.
This is a class A amplifier, wrongly designed. The transistors work "saturated" so in the loudspeaker constantly passes a voltage equal to (Ucc-0.7) volts, which will lead to its destruction. In order to be functional, a correct polarization of the transistors and an impedance adaptation with a transformer must be made.
FIRST your assembly method are inimaginably artistic ,im pretty impressed by the way you placed all component , you need to be proud of what you make , and you need to be proud to help the future im electronic thechnician and all i can say its , wow thanks , for salvaging component the right way Gratz from quebec Canada
A couple of things... 18W max @12V (1.5A x 8ohm load) With a 4ohm speaker you would double the current and wattage, also if you use a voltage doubler or boost power circuit you can get more wattage. Of course all the components would have to have voltage ratings to support higher voltage and proper thermal heat dissipation as well. When bridging the output of transistors to split the current amongst the transistors, you must send the output of each transistor through a .1ohm resistor to account for the variables in manufacturing of the transistors. Only a positive voltage can be applied to the speaker. This would be considered a push amplifier instead of a push/pull amplifier that can also apply a negative voltage as well. A speaker can push out and also pull in to match the waveform of the music. I am not an electronic engineer but have been repairing electronic, electro/mechanical devices for 40 years and I am certain there would also need to be other support components to create a quality signal output and efficient amplifier.
Sem considerar a eficiência do amplificador classe A, ou seja, 50%. 3.1 / 2 = 1.55W. Without considering the efficiency of class A amplifier, that is, 50%, 3.1 / 2 = 1.55w
Hi: Tengo todos los componentes que se necesitan, pero solamente 2 13007 y 2 BC 548C, puedo utilizar uno para llegar a los tres que solicita el circuito, utilizar los 4 ? que me sugeris. gracias
It's like the first amp I ever built when I was 14. Mine used only a single transistor and a 12V adapter. Your coil is not necessary, unless you want to pass only bass, you should use a much bigger coil. Quick, dirty, and effective, but most certainly not an optimal design (DC goes through the voice coil, raising it's temperature). This is a class A constant current amplifier (no electrical voice-coil damping/control), open loop (no feedback) and direct connected output (no capacitor). Have fun and be safe!
@cleber g pereira Spawn around 1000uF - 2200uF. Note, capacitor value will affect the frequency response. The lower the capacitance, the less bass you will get.
▬ Esse tipo de amplificador é só para iniciantes em eletrônica. Funciona, porém há grande desperdício de energia na forma de calor tanto nos transistores como no alto falante, além de por este em risco, caso opte-se por uma fonte mais potente e os transistores venham a entrar em curto por aquecimento. O resultado será a fonte descarregar toda a sua energia no falante e, caso demore-se a tomar uma atitude, a bobina pode vir a queimar por aquecimento acumulado. Meu conselho é que façam a montagem apenas por didática, testem mas evitem usar no dia a dia, e aprimorem-se num projeto só um pouquinho mais complexo, tipo com mais alguns transistores, que dê maior rendimento e mais potência. Há diversos projetos simples com transistores e/ou circuitos integrados de cinco pinos e poucos componentes externos, dispensando, inclusive, uma placa de circuito impresso.
Hola Muy Bueno tu proyecto amigo, me parece excelente, recuerda colocar el el diagrama de circuito electronico el Potenciometro para que la gente pueda ver el circuito completo. Saludos
Id imagine this is just a small project to show the basics of an amplifier... I can fix them, but I've never built one from scratch like this, interesting to see something so simple work like this... Now to learn how to take this and make it bigger and cleaner lol.
ola meu amigos....montei o circuito com 4 transistores 13007 e coloquei como pré um amplificador de caixa de som de pc com tda2822 e o resultado foi muito....e pode ligar junto aos 12v pois o tda2822 suporta ate 15volts e tbm alimentei todos os circuitos com uma fonte de pc.....show
@@Geek_142 Спаяй конструкцию, послушай. Потом напишешь каково. Вообще можно было не разбирать ИБП, а залезть в цепь ООС (цепь стабилизации выходного напряжения) , и получить полноценный усилитель "D" класса.
also, how would you know that the sound is not clean? the speaker isint even in a box. speakers always sound a lot better once you put them in a good box.
@@adamhosseinei8631 Because we've seen the schematic. This will be distorted. Also will put DCcurrent through your speaker, which means it will lower performance and maybe even damage the speaker over time. Happend to me with similar circuit...
Could I use a 19v 3.4a notebook power supply? Already working with a 12v 1.5a power supply The potentiometer I'm using is the B10k and it didn't get too loud. I am looking for a 100k. Can I add a 12v led to indicate it is on?
Buena broder ya q utilizaste repuestos q estan al alcanse talves no de todos pero esa es la idea de reciclar y mejorar algo q ya tenias felicidades papa y sigue con los videos q yo te seguire y recomendare con amigos! Suerte papa
Bien joué avec si peu de récupération sur une alimentation d'ordinateur ! J'ai vu le commentaire où elle dit 100%fake mais moi je sais que c'est possible !
Doubtful, would be funny to see on on a PC's power supply. He's using an off- the-shelf 100k potentiometer. AliExpress, eBay, Amazon sell working ones.
These are not linear transistors, they're designed to switch rapidly, so the distortion is about 10%. Also "powerful" is not a good description, with a 12V power supply and an 8ohm speaker, you should get about 4V RMS voltage, current will be 0.5A and your power will be 2W at the absolute maximum. Ok, it might be 4W with a 4 ohm speaker. That's not powerful. And since music has drumbeats and similar surges, you wouldn't get more than 1W, really. So, what you have made is a 1W fuzzbox. I suppose if you have an old power supply and nothing to do with it and you're not fussy about all your music sounding crappy ...
I have a problem. I already set up the circuit and it works for a few minutes and the sound input suddenly disconnects and stops playing. What could it be?
en el otro post tuyo de dos 13007, explique que lo hice igual pero no tengo sonido en los parlantes (bocinas). usé estos componentes pero en lugar de 3 13007 puse dos que son los que tengo. alguna sugerencia ??
So many questions... I have very little understanding of componetized electronics... Always wondered how to do a simple amp like this... But why not use a cap and resistor per transistor? Like i said, i have very base line "youtube" knowledge on stuff like this, but it'd be my understanding that the sound wouldve been cleaner with less distortion if each transitor had a cap and it'd change the hertz of the sound range per resistor used? Am i correct to say you should be able to have used as many capacitors on a device like this and it'd just help carry a load without constantly pulling power? As in that it wouldn't effect anything other than it's ability to have power as it needs it withou constantly pulling "fresh power" from the battery or the power plug?
Gostei, se precisar de um mais potente basta aumenta a capacidade em dobro de cada componente, ou tem outa i deia diferente, muito bom e simples bom eu não entendo muito, mais trabalho com computador e jogo essas fontes na sucata fiquei interessado pela ideia valeu, Manaus /AM Brasil
Chris Bourassa the Toriid coil in series is a low pass filter but isn’t calculated for crossover freq., it’s whatever it ends up. that’s a extremely large coupling capacitor I thought he would filter power with it . The pot could be tied to ground or center instead of open. I haven’t ever seen supply voltage to circuit fed thru the speaker before. So I’m with the person making top comment of 100% fake project. never used beyond proof of concept
Dave Zimmerman yea, 1,000 uF? I was thinking smoothing cap for the DC supply for sure, not coupling cap. I would have thought no more than 100 uF at the most. Wouldn't a cap that big lose some of the high frequencies without a smaller cap, like a .1 to 1 uF, in parallel with it? I have lots of circuit diagrams of audio amplifier circuits, one high power one with 9 complimentary pair amps in parallel, in class AB, and it only uses a 1 uF input cap. Granted it has a long tail pair differential amp input stage and two additional amp stages before the 9 comp pair output stage, but still. This amp just seems to have sound quality better than I would have thought it should have for no more than it has to it. Also would 1K bias the transistor bases where they would need to be for a proper quiescent point without cutting off the tops of the loudest waveforms in saturation, or the bottoms below the cutoff point? This looks like a common emitter amp setup, but I would have put a load resistor on the collector to the positive supply, a couple of coupling caps like a 1,000 uF and 1 uF for a small speaker like this, or a 4,700 uF and 1 uF for bigger speaker(s,) on the collectors to the speaker(s,) the speaker(s) to the emitters, a biasing voltage divider on the bases and figured out what values it needed for a good quiescent point, and I might have even considered a low value emitter degeneration resistor and bypass cap to trade a little gain for improved stability and linearity of the amp. Of course I could be wrong, my knowledge of electronics and audio amps is limited to what I've read in books and online, I haven't taken formal classes or anything, it's just a hobby, but this amp though meant to be a piece together from old parts, just seems too good to be true, to me.
The interesting in this project , is that he is recycling the materials from an old PC power supply that's a plus for the enviroment . Good Job VN TECH !
Mano o segredo é o dissipador de calor. Eu acompanho os projetinhos desse cara há 2 anos! E todos que fiz até agora deram certo. Tem uma semana que to curtindo esse projeto no meu subwoofer de 350w rms, e tá só filé! Curto com mais 3cx ligadas em outro amp, separado. Já curti por 2 anos seguidos com outro de 2 transistor. Um dissipador aumenta a vida útil deles. Bom tunts tunts ae! ;)
Muy buen proyecto hermano, pero le falta un componente para que el sonido no se distorsione, lo arme y le puse un capacitor np de 2.2uf 50v sin polaridad y me resulta mejor el sonido
Electrical Engineer here. You need to isolate the speaker from the 12V line. Remove the inductor (labeled as coil). Now connect the 12V directly to the transistors instead of through the speaker. Put the speaker in parallel with the transistors, one side to the 12V line and the other to ground. Add a large capacitor between the speaker and the 12V rail with (-) side to the speaker. This should isolate the speaker from the 12V, preventing it from damage. It should also make the audio sound a bit cleaner. Improving on this: Calculate a base input voltage offset to keep transistors in active mode and add a resistor from base pins to ground. It'll reduce distortion.
How?can you modified that sercuit
In my opinion, best he can do is to use two of these 13007 as push-pull topology, not as "quasi-darlington" single ended. It present topology it's easier to get transistors fully saturated, which causes distortion. Second thing is that single ended amps (A class) have less efficiency than push-pull amps (AB class).
On the other hand, testing bass speaker in "free air" conditions is not a good idea. Even a weaker amp can provide some bass if the speaker cabinet is calculated correctly. Enclosure makes at least half of job in providing bass from the speaker.
And the last thing. Wanna see speaker bouncing? Use a real woofer speaker, not noname like this. This magnet looks really tiny, and suspensions of this speaker can be too hard :) Maybe Eminence Lab12?
This guy is an idiot, you NEVER pass DC through the speaker, but he always does!!
@@MichaelBeeny said, "This guy is an idiot, you NEVER pass DC through the speaker, but he always does!!"
Bit of a harsh way for you to offer your constructive criticism, isn't it Michael?
@@MichaelBeeny will damage speakers
This is a Common Emitter design with Collector Feedback. The only reason I can see why you would find the need to put the 3 transistors in parallel is to handle larger currents for stable load lines effects (each transistors can handle up to 8 A, 80W, and 400V).
Also since these are switching transistors, they are not the best amplifiers. Nice project.
I would suggest that you use these transistors in Darlington configuration to get higher hfe values.
I need your knowledge lol... Because i have no idea what your alien language is... And somehow i ended up turning a simple 10 watt computer speaker amplifier into a stable 350 watt setup... Lucky i guess, teach me your ways lol
@jamdvx Increasing the input to too high a level will cause distortion. The standard for input levels to transistor amplifier preamp like this is about 1 Vpp or 1 volt peak to peak.
The comments section is full of self appointed experts. Lads, he's not aiming for hifi here, he's just showing you a fun little circuit with a few old parts.
well if these people want to keep using the titles that they do then make literally the same exact thing so many other youtubers have done using the same bs titles then they can expect the same kind of criticism
No HiFi but at least proper implementation of low frequency aplifier.
I think it's a cool little project that looks fun to try, but these people are taking it way too serious.😜
@@paulzedx636ninja7 Maybe the project is cool, but when some young person with not so much knowlege try to do it, and burn down its audio source (phone maybe) and speaker (transistor short circuit), that video is becoming a very bad way to learn electronics. This circuit is high ineffective and in some situations its could be even dangerous.
You could literally use the exact same parts and make something that sounds good , if you build it correctly and not just slap stuff in the wrong places. Never put DC through a speaker. Efen just using an inductor in the collector would have worked better, look up inductor class A amps.
That's pretty sweet you were able to build that. The power isn't too impressive but it's definitely cool. I'm a fan bud. Good job
Philmonster K lol I’m a bud fan
This is a class A amplifier, wrongly designed.
The transistors work "saturated" so in the loudspeaker constantly passes a voltage equal to (Ucc-0.7) volts, which will lead to its destruction.
In order to be functional, a correct polarization of the transistors and an impedance adaptation with a transformer must be made.
Hey It looks like you know a lot about amplifiers. I made an amplifier as well so check it out my channel name : DIYkING 9K
Can I use 1500uf 10v ?
FIRST
your assembly method are inimaginably artistic ,im pretty impressed by the way you placed all component ,
you need to be proud of what you make , and you need to be proud to help the future
im electronic thechnician and all i can say its , wow
thanks , for salvaging component the right way
Gratz from quebec Canada
No encuentro uno de los complnentes y es el filtro q es de mil v16 ten uno pero es de 2000 y es de 10v estara vien ese d hay digame gracias
Nice home built mini-amp, how much effect does it provide with that small power-transformer?
How much juice and you use for such small construction?
That's why I like you
Keep it up brother.
Md.Najmus Sakib UN
See quad bass amplifier
@@jesrealpascuapacoy8814 bbmj
A couple of things...
18W max @12V (1.5A x 8ohm load) With a 4ohm speaker you would double the current and wattage, also if you use a voltage doubler or boost power circuit you can get more wattage. Of course all the components would have to have voltage ratings to support higher voltage and proper thermal heat dissipation as well.
When bridging the output of transistors to split the current amongst the transistors, you must send the output of each transistor through a .1ohm resistor to account for the variables in manufacturing of the transistors.
Only a positive voltage can be applied to the speaker. This would be considered a push amplifier instead of a push/pull amplifier that can also apply a negative voltage as well. A speaker can push out and also pull in to match the waveform of the music.
I am not an electronic engineer but have been repairing electronic, electro/mechanical devices for 40 years and I am certain there would also need to be other support components to create a quality signal output and efficient amplifier.
Sem considerar a eficiência do amplificador classe A, ou seja, 50%. 3.1 / 2 = 1.55W. Without considering the efficiency of class A amplifier, that is, 50%, 3.1 / 2 = 1.55w
Now I would Like to see a Audio Spectrum, from the Low, LOW's to the High' HIGH's..
Buen experimento para probar y motivar a los que se inician en electronica. Un aporte amigo.
Hi: Tengo todos los componentes que se necesitan, pero solamente 2 13007 y 2 BC 548C, puedo utilizar uno para llegar a los tres que solicita el circuito, utilizar los 4 ? que me sugeris. gracias
Hola broh pasa pasa por mi canal tengo lo q necesitas hacer.
Nice soldering iron tip
It's like the first amp I ever built when I was 14. Mine used only a single transistor and a 12V adapter. Your coil is not necessary, unless you want to pass only bass, you should use a much bigger coil. Quick, dirty, and effective, but most certainly not an optimal design (DC goes through the voice coil, raising it's temperature).
This is a class A constant current amplifier (no electrical voice-coil damping/control), open loop (no feedback) and direct connected output (no capacitor).
Have fun and be safe!
Replace the coil with a capacitor, and this design would be fine.
@cleber g pereira Spawn around 1000uF - 2200uF. Note, capacitor value will affect the frequency response. The lower the capacitance, the less bass you will get.
puedo usar este amplificador asi en las bocinas de mi carro
Strange how a speaker works with DC voltage....that circuit looks like a simple boost converter, not suitable for audio signal boost...
It doesn't, not for very long, anyway.
Nice
13003
In cfl lamp
Thx. I got this transistor on my old lamp
woah so powerfull the membrane was so scared it didn't move
Lol
How many watts do you think the output is? Do you think adding more transistors would increase the power?
That's not how it works...
@@AstrosElectronicsLab I posted this in 2019
@@oofig I realise that, I was just responding.
Me gustó voy a buscar las piezas para hacer uno así gracias hermano
Te funcionó??
mano el primer transistor que cambiaste es igual que los otros?
▬ Esse tipo de amplificador é só para iniciantes em eletrônica. Funciona, porém há grande desperdício de energia na forma de calor tanto nos transistores como no alto falante, além de por este em risco, caso opte-se por uma fonte mais potente e os transistores venham a entrar em curto por aquecimento. O resultado será a fonte descarregar toda a sua energia no falante e, caso demore-se a tomar uma atitude, a bobina pode vir a queimar por aquecimento acumulado.
Meu conselho é que façam a montagem apenas por didática, testem mas evitem usar no dia a dia, e aprimorem-se num projeto só um pouquinho mais complexo, tipo com mais alguns transistores, que dê maior rendimento e mais potência. Há diversos projetos simples com transistores e/ou circuitos integrados de cinco pinos e poucos componentes externos, dispensando, inclusive, uma placa de circuito impresso.
Kya iss se 10 inch ka speaker 2 baja sakte hai
Hola Muy Bueno tu proyecto amigo, me parece excelente, recuerda colocar el el diagrama de circuito electronico el Potenciometro para que la gente pueda ver el circuito completo. Saludos
mira este video, el circuito es similar: th-cam.com/video/4bJwRG_Hino/w-d-xo.html
Sirve para celular?
good job! Take speaker into bass box reflex for better effect :)
Best technique 😍😍🤩🤩👉👍👍
That's why I love Electronics Engineering
walter Floriano Está faltando no esquema o Potenciometro,,, Incompleto...
hey can i use a 10k potentiometer instead of the 100k one?
Excellent video.
i bet you love that old soldering iron so much.
Lol that's gonna always be look like that no matter we love it or not.
Bro can i know where can i find these transistors for mai basstube i want to make emplifer
Pleese help me bro
You can find it in the PC power supply
Que los 12voltios van al parlante????
Building an amplifier out of nothing.. thats what this is all about.. its not about. how good and how bad the amplifier is.. Think!
Id imagine this is just a small project to show the basics of an amplifier... I can fix them, but I've never built one from scratch like this, interesting to see something so simple work like this... Now to learn how to take this and make it bigger and cleaner lol.
@@dragoon9082 redesign it.
serve pra fone de ouvido ?
Tá faltando o capacitor eletrolítico e o potenciômetro no seu diagrama.
Não ta não.
L
@@geraldinosouza52 สจ
@@pronsakchannel394ছননট্রধট্যঠছ্রধঠচ্রধঠে
🤔
ola meu amigos....montei o circuito com 4 transistores 13007 e coloquei como pré um amplificador de caixa de som de pc com tda2822 e o resultado foi muito....e pode ligar junto aos 12v pois o tda2822 suporta ate 15volts e tbm alimentei todos os circuitos com uma fonte de pc.....show
Pra que serve o potenciômetro? Se eu não vi ele aumentando ou baixando
Acredito que ele deixou na potência máxima já... mas obviamente que o potenciômetro serve para baixar ou aumentar o volume!
Bendiciones, buenos tus videos, pero en ningún video indicas de cuantos watts deben ser las cornetas, por lo demás excelente
🇧🇷🙂👍 Legal Muito BOM 👏👏👏👏👏👍 PARABÉNS
Sigue Asi Hombre Unos De Los Mejores 100% Real Y 100% Calidada No Le Pares a Comentarios Malicioso,
Через динамик проходит постоянный ток, причем не маленький. Что и слышим на видео.
Игрушка только для подбрасывания шарика, Не для музыки.
На мой взгляд для саба само то!
@@Geek_142
Спаяй конструкцию, послушай. Потом напишешь каково.
Вообще можно было не разбирать ИБП, а залезть в цепь ООС (цепь стабилизации выходного напряжения) , и получить полноценный усилитель "D" класса.
@@wolfthegrey5165 скинь схему
@Denny Boys
Диффузор динамика вжат в одну крайность, обмотки греется. Сам ответил на свой ответ.
вы сейчас сами поняли о чем говорите???@@wolfthegrey5165
It's pretty awesome to see a class a amplifier, badly designed and implemented make 3.1 million views on TH-cam.
it may be strong but the sound is not clean
where in the circuit would you put that?
also, how would you know that the sound is not clean? the speaker isint even in a box. speakers always sound a lot better once you put them in a good box.
@@adamhosseinei8631 Because we've seen the schematic. This will be distorted. Also will put DCcurrent through your speaker, which means it will lower performance and maybe even damage the speaker over time. Happend to me with similar circuit...
ভাই এবাজে না তো,
@@adamhosseinei8631100% quaranted the sound is not clear. Too much distortion and noisy. Because it's a very simple amplifier with no filter at all.
Funciona con el D13007??
Powerfull bass?
😂😂
Super👍👌👏😊
я один ждал когда он будет крутить звук на самом уселке?
нет, я тоже ждал, но нихера, думал через резистор будет уменьшать увеличить громкость
@@rifan_92gerych99 до самого конца из-за этого смотрел
бля, повторил эту хуйню, больше половины громкости звук пердит хрипит
по такой схеме другого и не будет)))
Я тоже думал когда же он покажет что звук можно регулировать
Could I use a 19v 3.4a notebook power supply?
Already working with a 12v 1.5a power supply
The potentiometer I'm using is the B10k and it didn't get too loud.
I am looking for a 100k. Can I add a 12v led to indicate it is on?
Vc ta de parabéns!!
it can be done with other transistors or must be 13007?
Woooooou this is more than powerful base
This is just for bass,or can put and high?
A circuit schematic would be most useful... Fair play for recycling electronic components though :-)
Huh? Isn't 6:55 sufficient. And, an up-tick to you for giving him kudos for electronic component recycling. Something more of us should be practicing.
Buena broder ya q utilizaste repuestos q estan al alcanse talves no de todos pero esa es la idea de reciclar y mejorar algo q ya tenias felicidades papa y sigue con los videos q yo te seguire y recomendare con amigos! Suerte papa
what about a BC212L driving two 13007 or BD131 transistors.
to milai
Şımdiye kadar nereden baktıysam olmadı senin sayende yaptım çok teşekkür ederim
Bien joué avec si peu de récupération sur une alimentation d'ordinateur !
J'ai vu le commentaire où elle dit 100%fake mais moi je sais que c'est possible !
Comment cest possible
Can you use this to power a fleshlight?
Hahaha yes i think you can
You got the volume knob from the pc power supply as well?
Doubtful, would be funny to see on on a PC's power supply. He's using an off- the-shelf 100k potentiometer. AliExpress, eBay, Amazon sell working ones.
@@rastanot thank you for replying to me not even your channel appreciate it thank you again
Naw, psu's don't rock buttons. Order the buttons suggested
@@justinmoore8097 You are very welcome.
Where's the potentiometer in your circuit diagram?
look this video at 4:03, the circuit is the same : th-cam.com/video/4bJwRG_Hino/w-d-xo.html
@AKM REVOLTS i think this not functional, because you need more than 12vdc
Is this all possible when done
Increase the supply voltage to 400v and it will improve the bass response although only for a short time 🤔......💣💥🔇⚰😂
haha fireworks on the way
you are asshole? 400v? wtf?
And blow the ass off the transistors 😮
U make complicated things look very easy.. Thanks...
These are not linear transistors, they're designed to switch rapidly, so the distortion is about 10%. Also "powerful" is not a good description, with a 12V power supply and an 8ohm speaker, you should get about 4V RMS voltage, current will be 0.5A and your power will be 2W at the absolute maximum. Ok, it might be 4W with a 4 ohm speaker. That's not powerful. And since music has drumbeats and similar surges, you wouldn't get more than 1W, really. So, what you have made is a 1W fuzzbox.
I suppose if you have an old power supply and nothing to do with it and you're not fussy about all your music sounding crappy ...
dude you're cool with your tips. But his technique works.
@@electromechanik4740 I don't call it working if you really can hardly hear a note.
I have a problem. I already set up the circuit and it works for a few minutes and the sound input suddenly disconnects and stops playing. What could it be?
Ottimo sistema per distruggere l'altoparlante che è sempre attraversato da continua. 6 volt su 8 ohm quasi un amper di corrente sulla povera bobina.
In realtà l'altoparlante si comanda in corrente, vedi un classe A o un classe AB, o semplicemente un collettore comune
en el otro post tuyo de dos 13007, explique que lo hice igual pero no tengo sonido en los parlantes (bocinas). usé estos componentes pero en lugar de 3 13007 puse dos que son los que tengo. alguna sugerencia ??
Real test is to use an old school analog synthesizer with it. Square wave!
So many questions... I have very little understanding of componetized electronics... Always wondered how to do a simple amp like this... But why not use a cap and resistor per transistor? Like i said, i have very base line "youtube" knowledge on stuff like this, but it'd be my understanding that the sound wouldve been cleaner with less distortion if each transitor had a cap and it'd change the hertz of the sound range per resistor used? Am i correct to say you should be able to have used as many capacitors on a device like this and it'd just help carry a load without constantly pulling power? As in that it wouldn't effect anything other than it's ability to have power as it needs it withou constantly pulling "fresh power" from the battery or the power plug?
good build, but you can assemble one of the Soviet transistors such as kt700 series
Rom4ik Gerasimov л
Bueno
Buen dia.
Asta q capacidad d watts d la bocina puede aguantar
Parabéns... ficou top o projeto.
Una pregunta se puede hacer solo con 2 transistores ?
You put DC voltage on your speaker coil.
I assume it's just a simple class A amplifier
Done, it works great. It is fantastic, a bombshell. Congratulations nice project.
De cuanto tiene que ser la bocina
Gostei, se precisar de um mais potente basta aumenta a capacidade em dobro de cada componente, ou tem outa i deia diferente, muito bom e simples bom eu não entendo muito, mais trabalho com computador e jogo essas fontes na sucata fiquei interessado pela ideia valeu, Manaus /AM Brasil
Hey man, very nice. But how do you know what is impedance out? Thanks for now
Three transistors in parallel... only one works, the speaker wouldn't support the continuous current... this circuit won't work!
It's a friking darlington bridge! not "three transistors in parallel"
На долго динамика хватает? Диффузор не греется?
Катушка динамика будет греться-на выходе постоянка. Тупая схема,как и сам автор.
Что бы не грелась, нужно динамик мощнее. А вообще я не физик, но интересно, что из 5 старых деталей, можно усилок сделать.
@@chipsed Схема в принципе неправильная.Думай.Нужна комплементарная пара.
@@chipsed что бы не грелся нужна другая схема ,а не это говно)))я удевлён что кто то заметил это
@@ПавелС-ш8м так оно работает! ))
@@chipsed можно ,но если только для баловства)
I'm inspired of this idea on how we can turn our old electronics devices into something great innovations
1,000% THD ;^)
Veo que usaste los transistores de la Fuente del cpu y este tiene 6 se puede hacer con los 6?? Y tendrá más potencia este?
Full range amplifier. No crossover, can hear full frequency range from the speaker. Bwahahhahahahha
Chris Bourassa the Toriid coil in series is a low pass filter but isn’t calculated for crossover freq., it’s whatever it ends up. that’s a extremely large coupling capacitor I thought he would filter power with it . The pot could be tied to ground or center instead of open.
I haven’t ever seen supply voltage to circuit fed thru the speaker before. So I’m with the person making top comment of 100% fake project. never used beyond proof of concept
Dave Zimmerman yea, 1,000 uF? I was thinking smoothing cap for the DC supply for sure, not coupling cap. I would have thought no more than 100 uF at the most. Wouldn't a cap that big lose some of the high frequencies without a smaller cap, like a .1 to 1 uF, in parallel with it? I have lots of circuit diagrams of audio amplifier circuits, one high power one with 9 complimentary pair amps in parallel, in class AB, and it only uses a 1 uF input cap. Granted it has a long tail pair differential amp input stage and two additional amp stages before the 9 comp pair output stage, but still. This amp just seems to have sound quality better than I would have thought it should have for no more than it has to it. Also would 1K bias the transistor bases where they would need to be for a proper quiescent point without cutting off the tops of the loudest waveforms in saturation, or the bottoms below the cutoff point? This looks like a common emitter amp setup, but I would have put a load resistor on the collector to the positive supply, a couple of coupling caps like a 1,000 uF and 1 uF for a small speaker like this, or a 4,700 uF and 1 uF for bigger speaker(s,) on the collectors to the speaker(s,) the speaker(s) to the emitters, a biasing voltage divider on the bases and figured out what values it needed for a good quiescent point, and I might have even considered a low value emitter degeneration resistor and bypass cap to trade a little gain for improved stability and linearity of the amp. Of course I could be wrong, my knowledge of electronics and audio amps is limited to what I've read in books and online, I haven't taken formal classes or anything, it's just a hobby, but this amp though meant to be a piece together from old parts, just seems too good to be true, to me.
The interesting in this project , is that he is recycling the materials from an old PC power supply that's a plus for the enviroment . Good Job VN TECH !
Hola te consulto ? Si agregas más transistores podes obtener más potencia? Gracias!!!!
👏👏👍Consegui fazer, mas esquenta muito os componentes.!!!
Mano o segredo é o dissipador de calor. Eu acompanho os projetinhos desse cara há 2 anos! E todos que fiz até agora deram certo. Tem uma semana que to curtindo esse projeto no meu subwoofer de 350w rms, e tá só filé! Curto com mais 3cx ligadas em outro amp, separado. Já curti por 2 anos seguidos com outro de 2 transistor. Um dissipador aumenta a vida útil deles. Bom tunts tunts ae! ;)
@@eduardoromulomileo4814 valeu pela dica!
Os transistor que usei foi o D2396, o som ficou muito alto e de boa qualidade muito top! 👍👍
@@eduardoromulomileo4814 pra alimentação so essa fonte de 12 volts 1.5A aguenta?
@@eduardoromulomileo4814 e no circuito o capacitor ta no primeiro transistor enquanto na montagem que ele fez o capacitor ta no meio ????por que isso?
@@10111rodrigos Pra tocar bem, mais forte, precisa de mais amperagem. Com 12v e uns 5a, já ta bom!
Suena súper aparte de q es muy sencillo hacerlo 👍👍 sigue asi
Gostaria de ver mas montagens com explicação em portugues falado ou legendado
Mais o vídeo é gringo
tem videos brasileiros sobre o mesmo assunto,porem nao se usa bobina e se usam 2 transistores
A bobina é pra tirar os ruídos e não deixar o volt ir direto pro alto-falante 🔊
Copper coil size..?
How many watt can it supply to the out put?
keep away from very basic design ampli such as this one,this is very unstable,hi distortion,and will destroy your speakers later.
in this case it won't take too long, given the significant DC on the output!
Poq trocou o primeiro transistor?? Eu fiz tudo igual.. so que o som nao saiu... O auto falando ficou so chiando.. poq sera??
LOL ""Powerful""? With 12V/1,5A power supply? Are you kidding?
Yess this is working
I have also made it
@@karankumargiri1204 me too but i meassure its output wattage it's only 5watts in 4ohm speaker and 3watts in 8ohm speaker
Thanks, constant current through the speaker. Dangerous!
do not use on any speakers especially expensive ones ... could damage speakers easily due to DC across the voice coil
is it possible to use the D718 transistor?
Muy buen proyecto hermano, pero le falta un componente para que el sonido no se distorsione, lo arme y le puse un capacitor np de 2.2uf 50v sin polaridad y me resulta mejor el sonido
Yo intente hacer uno y no se esuchaba las bocimas eran bocinas de tv 😢
Los tres transistores son de 13007??
Una pregunta amigo tengo todos los conponentes pero el transistor que canbiaste x otro estaba malo o los 3 tienen quewer iguales responde gracias
Los 3 son iguales maestro