It would be better if you didn't claim absurd numbers. 3800W out of 12V is 316 amps. Not only your thin red&black wire would instantly bust into fumes, but even the transistors wouldn't stand it. The 2SC5200 is max 15A, i.e.max 180W with your schematic. Also you wired the jack in reverse polarity, and your two resistors are connected in parallel. And based on the wire size it looks like what you connected the transistors to was in fact the 220V primary, and the speaker is connected to the 12V secondary. This is a UPS transformer designed to work as a full bridge. There's not necessarily anything wrong with the final assembly as long as it does the job for you (i.e. make lots of noise), but you wrote a lot of errors and are inducing your readers into making errors.
Jika terjadi short pada transistor, akan menyebabkan HP anda mati. Karena input audio tanpa melewati kapasitor kopling . Respect untuk kreatifitas anda,
The circuit does not work. You cannot make the speaker swing in both directions with two pairs of NPN 2SC5200 output transistors without a phaseinverter. The real amplifier is inside the batterybox. The only point with these videos is to get clicks and earn money.
And fun fact is can see the output and input terminals of that transformer?!!! why 220V wires need to that thicker and 12 0 12v wires is literally way more slimmer as equal to nothing.
Aparentemente tem ligações erradas e/ou valores fakes tanto no falante como no transformador. mas existe essa possibilidade de usar transformadores nas saídas dos AMPs. mas não com essa ligação. mas tem que testar para ver se funciona. Valeu por compartilhar.
Ele basicamente fez um amplificador tipo booster, nos anos 90 esse tipo de amplificador era o padrão no mercado de baixo custo, tinha tojo ab200, stetsom cl500, aquarius by faitron (hoje banda)
Chyba raczej na głośniki się obniża napięcie, żeby uzyskać większe natężenie prądu. Przy zasilaniu 12 V, w tym podłączeniu transformatora, licząc straty, idzie na głośnik około 200.v. Nie będę tego próbował zrobić, ale wątpię czy to zagra.
Tradus ai!!! entra 12v DC e sai a frequencia mais 12 AC que é normal para esses amplificadores antigos classe A. Dai so falta o pre-amplificador para filtragens, ampliar o som, definir a qualidade,limite de volume !!!
Greetings from Bosnia-Herzegovina 🙋♂️🤝...Don't worry, it won't burn unless you burn it, I tried it successfully, it was very satisfactory after I added a volume regulator and replaced the battery to adjustable 12v adapter👍🌟🌟🌟🌟⏯️...
Circuit shown will not work. Audio In is connected with ground( ie :- transistor base is grounded).. Also why 2 nos 10k resistors given parallel from same trace..?
Now that's a cool class-A amp, can you make a high quality, 1,000 watt RMS Class-D mono-block, and a separate 2 channel, 2,000 watt RMS (1,000 watts each channel) Class-D amplifiers????
@@Zilongofficial5678 is it capable of the 1ohm load,it'll fry your amp if not...does it get hot to the touch,or dam that's hot,after long..just wondering
Да ты тролль ))) А ничего что обезьяна, даже не читала Datasheet? И пара транзюков, естественно комплементарная ))) Да они скорее всего, уже пробитые. Учитывая что выковыряла обезьяна их, из старого БП.
Very nice. But please install one Bluetooth on it, then it would be fantastic. But be careful, you are sending direct power to speaker, it will burn out, on hi volume.
I do not believe the speaker is connected to a 220 volt winding. If the transformer is as labeled, the secondary 12-0-12 would be thicker than the 220 primary. It is the opposite. The primary winding labeled 220 has excessively thick copper leads. The label on the transformer is not correct.
1) Трансформатор не рассчитан на 3800W 2) 2SC5200 по документам выдерживает максимум 150W 3) Для получения большой мощности от 12В необходим преобразователь напряжения 4) Нет усилителя напряжения 5) Схема вообще не должна заработать. Это чистый развод! Если начертить схему этого "чуда", то вообще смешно становится. Например чтобы получить нормальных 25W с TDA2050 нужно запитать ее двухполяркой 20V.
I built this but then added a 36-pin Centronics parallel cable, then connected that to a flux capacitor then into my old Commodore pc10 II and when I switched it on, Kelly Lebrock appeared out of a puff of smoke! Too bad it was the current Kelly Lebrock instead of the 1980's one. 🤔 Maybe I should have used vintage age resistors. Oh well, got to go. It's time to turn Chet into a Jabba the hut look alike. 😅
Có chuyển bluotube đc ko và tăng giảm âm lượng chổ nào ko thấy giới thiệu ? Cổng kết nối USB chổ nào ? Cổng dùng điện thế 220V được ko ? Nhiều thắc mắc khác nửa .
Pls describe what type of amp is this..looks like an attempt to turn 12 dc to 240vac stepup voltage booster into an audio amp which is ridiculous ,it simply doesn't have the current to push large 8ohm speaker well
Better to connect 240 volt directly to the sub woofer and trying to connect with your phone. Surely you will feel the dance bar with fog and louder music😋😋😋😋
MUY INTEREZANTE ESTE PROYECTO Y MUY SENCILLO YO TENGO VARIOS MOSFET 38N30 Y QUISIERA FABRICAR UN AMPLIFICADOR CON ELLOS PERO NO EH PODIDO ENCONTRAR UN MODELO PARA YO REALIZARLO SI USTED ME PUEDE AYUDAR LE ESTARE MUY AGRADECIDO
El vídeo es falso la mayoría son falsos 8:46 ah se puede ver cómo tiene el Bluetooth activado el amplificador es la batería si quiere hacer un amplificador con mofets busque el diagrama por internet no crea en estos video gracias
This would work better if the speaker was connected across the 2 12v windings instead of the 220v one...and just leave the 220v unconnected, connecting to the 220v side is loading the amp down way too much and you are losing power. Doing this and running into 1 ohm you could get up to 200 watts RMS with a 12 volt supply (assuming the transistors can take the current)
POR FAVOR SRES DE BRICOLAJE TECNICO; YO HICE UN CIRCUITO IGUAL A ESTE DE 3800 W PERO LE PUSE EL AUDIO Y NO SUENA NO HAY SALIDA DE AUDIO: SI ME INFORMAN QUE PUEDO HACER PARA SACAR LA SALIDA DE AUDIO SE LOS AGRADECERÍA GRACIAS
Nggak usah,kejebol nantinya,..rakitan itu sangat merbahaya pda hape jika anda tidak menggunakan tipe c adaptor seperti divideo kerna kabel phone audionya disambung terus pda sumber daya baterinya...It's Very risky on your mobile phone🔥AWAS!!!💥...
Sebenarnya. Banyak perangkat yang di buat China. Hampir semua kit. Ada. Sudah bagus murah dan mudah. Merakitnya. Hasil ok punya cuy.. Saya dulu sering buat. Sekarang sudah bosan. Banyak toko elektronik menyediakan. Kit. Yang cakep dan ok. Punya. Murah meriah dan jossss
Cara isso não é um alto falante de 2500 watts nunca, primeiro pelo tamanho do conjunto magnético, e segundo todos os vídeos que você faz, você nunca deixa o adesivo original do alto falante, sempre tira as informações do alto falante, e vem e escreve a mão a quantidade de watts que quiser no alto falante e quarto , podem reparar é sempre o mesmo alto falante velho e sujo, nunca é um bom alto falante cone seco ou borrachudo.
*New idea:* th-cam.com/video/X7L1Z_QAK9M/w-d-xo.htmlsi=CiVIgMm3IGbQHzq5
It would be better if you didn't claim absurd numbers. 3800W out of 12V is 316 amps. Not only your thin red&black wire would instantly bust into fumes, but even the transistors wouldn't stand it. The 2SC5200 is max 15A, i.e.max 180W with your schematic. Also you wired the jack in reverse polarity, and your two resistors are connected in parallel. And based on the wire size it looks like what you connected the transistors to was in fact the 220V primary, and the speaker is connected to the 12V secondary. This is a UPS transformer designed to work as a full bridge. There's not necessarily anything wrong with the final assembly as long as it does the job for you (i.e. make lots of noise), but you wrote a lot of errors and are inducing your readers into making errors.
Jika terjadi short pada transistor, akan menyebabkan HP anda mati.
Karena input audio tanpa melewati kapasitor kopling .
Respect untuk kreatifitas anda,
Mksdnya hp mati hp nya bakal rusak?
it will damage the type C headset wire first and the phone will not be damaged
Inputnya ganti blutut bang,, JD aman 🙊🙊🤪🤪
The circuit does not work. You cannot make the speaker swing in both directions with two pairs of NPN 2SC5200 output transistors without a phaseinverter. The real amplifier is inside the batterybox. The only point with these videos is to get clicks and earn money.
Hi Brother
@All Digital Craft
Are you sure that there's a real amplifier exists?? 🤣🤣
@@jawadranjha6083 yes :)
You right Man 👍💯
And fun fact is can see the output and input terminals of that transformer?!!! why 220V wires need to that thicker and 12 0 12v wires is literally way more slimmer as equal to nothing.
Walang siraan..kapwa kayo pilipino..Ang ibang lahi bumati pa Ng congratulation..Pinoy talaga kahit saan mapanira sa kapwa Pinoy..
🎉Оддий усулда моно усилитель 🎉🎉 ажойиб видео учун катта рахмат Гафур бобо 🎉🎉🎉🎉🎉🎉
Aparentemente tem ligações erradas e/ou valores fakes tanto no falante como no transformador. mas existe essa possibilidade de usar transformadores nas saídas dos AMPs. mas não com essa ligação. mas tem que testar para ver se funciona. Valeu por compartilhar.
Ele basicamente fez um amplificador tipo booster, nos anos 90 esse tipo de amplificador era o padrão no mercado de baixo custo, tinha tojo ab200, stetsom cl500, aquarius by faitron (hoje banda)
2sc5200 is the best transistor
Wahh keren pingin buat dechh. 😂😂😂
Veri naic your teknic you geat brother I'm madan raj Indian
cool greetings from Brazil
Man that 2500w speaker is hilarious af 😂🤣😂😆
Fery good,superbass amplifier from trafo ups👍
Yes, this transformer from APC UPS
Thank you master this is amazing and awesome projeck👍👍👍
Chyba raczej na głośniki się obniża napięcie, żeby uzyskać większe natężenie prądu. Przy zasilaniu 12 V, w tym podłączeniu transformatora, licząc straty, idzie na głośnik około 200.v. Nie będę tego próbował zrobić, ale wątpię czy to zagra.
Tradus ai!!! entra 12v DC e sai a frequencia mais 12 AC que é normal para esses amplificadores antigos classe A. Dai so falta o pre-amplificador para filtragens, ampliar o som, definir a qualidade,limite de volume !!!
Greetings from Bosnia-Herzegovina 🙋♂️🤝...Don't worry, it won't burn unless you burn it, I tried it successfully, it was very satisfactory after I added a volume regulator and replaced the battery to adjustable 12v adapter👍🌟🌟🌟🌟⏯️...
Waw. Keren. Ultra. Baas. Ini. Suara. Nya. Nyaring. Mantul. Mantap❤❤❤
Circuit shown will not work. Audio In is connected with ground( ie :- transistor base is grounded).. Also why 2 nos 10k resistors given parallel from same trace..?
resistors connected in parallel to double the power
Yah he soldered the input hot wore to the negative
Excellent bro 👌👌💞💞💞💞💞
Thank you
Seperti rangkaian radio2 jaman dulu yang masih menggunakan travo primer dan sekunder
Now that's a cool class-A amp, can you make a high quality, 1,000 watt RMS Class-D mono-block, and a separate 2 channel, 2,000 watt RMS (1,000 watts each channel) Class-D amplifiers????
yes I gave one thumb up, very creative
It,s a output not 2500w buts a 200w 👍👍👍👍👍
i actually tried it with 2500 watts speaker and it works fine
It,s watt a speaker 2500w 1ohm yes
2500 is the pmpo while 200 is the rms
@@broccolixxx - Correct.
@@Zilongofficial5678 is it capable of the 1ohm load,it'll fry your amp if not...does it get hot to the touch,or dam that's hot,after long..just wondering
Wow..Music thai..Red Rose🎉🎉
Mantap bagus .dari indonesia terima kasih vidionya.
Pernah coba??? Nyala???
Одну канале усилитель 24 вольт 25. Ват Моно большое спасибо за хорошие видео понравился
thank u
Трансформаторная развязка 🙂 лучшая защита от пробоя транзисторов. Прекрасный ролик, лайк однозначно.
интересно будет такой усилитель работать модулятором для кв передатчика на транзисторах ?
Да ты тролль ))) А ничего что обезьяна, даже не читала Datasheet? И пара транзюков, естественно комплементарная ))) Да они скорее всего, уже пробитые. Учитывая что выковыряла обезьяна их, из старого БП.
@@колек-т6б всё можно. если хочется. но работать не будет
У этих транзисторов третяя ножка эмиттер , а первая база . Это даже как мультивибратор работать не будет .
Very nice. But please install one Bluetooth on it, then it would be fantastic. But be careful, you are sending direct power to speaker, it will burn out, on hi volume.
yep, I will improve in the next videos
I do not believe the speaker is connected to a 220 volt winding.
If the transformer is as labeled, the secondary 12-0-12 would be thicker than the 220 primary.
It is the opposite. The primary winding labeled 220 has excessively thick copper leads.
The label on the transformer is not correct.
1 ohm at secondar is a short .
@@saouga53 This device works. And it's inventive. This is what it looks like
The handwritten powerrating on the back of the speaker is also a lie. He does it on more videos.
He just welding details randomly on each video) slow down, it's not working, he is just a fat troll)
i don't believe usb charger plug has changed to a sound jack 😅😅
Luar biasa kreen sangat jenius kreativitas tinggi ,,,
audio input wires left right connecting to negative wire ??
Ang galing naman more power po
1) Трансформатор не рассчитан на 3800W 2) 2SC5200 по документам выдерживает максимум 150W 3) Для получения большой мощности от 12В необходим преобразователь напряжения 4) Нет усилителя напряжения 5) Схема вообще не должна заработать. Это чистый развод! Если начертить схему этого "чуда", то вообще смешно становится. Например чтобы получить нормальных 25W с TDA2050 нужно запитать ее двухполяркой 20V.
I built this but then added a 36-pin Centronics parallel cable, then connected that to a flux capacitor then into my old Commodore pc10 II and when I switched it on, Kelly Lebrock appeared out of a puff of smoke! Too bad it was the current Kelly Lebrock instead of the 1980's one. 🤔 Maybe I should have used vintage age resistors. Oh well, got to go. It's time to turn Chet into a Jabba the hut look alike. 😅
Very good 👍👍👍👍👍👍
saludos desde EL SALVADOR buen video.
Cara,
Voce é bom demais.
Parabéns
What did you record the final music with !. Thumping bass in the open air with no baffle
LOL, was wondering the same thing....
Very nice and good. Good luck
thanks
You dont short circuit with the 2 way audio in, like show in your vídeo. Risk of damage to áudio equipament linked to your "amplifier"
Aí sim valeu Agora Tem bastante potência 👍👍👍
It's barely 11PM and TH-cam already took me to the Twilight Zone
Dude, this was nauseating to watch, but amusing nonetheless :D
Exelente.... pero me confundí...es AC?????…gracias por su respuesta... Saludos.
AC
very smart. look at pain hand. 👍
i wish i was smart as you ..... i don't know how you do it ..... teach me .... i'll fly to china or vietnam to learn
a power transformer for the output ? whats the ohms coming out of that load
Inside of the the battery is the main amp.. and the audio is connected with Bluetooth😂
Estas cerca, observa bien el video y verás una corneta bluetooh amplificada en un trípode colocada del lado izquierdo del video
Có chuyển bluotube đc ko và tăng giảm âm lượng chổ nào ko thấy giới thiệu ? Cổng kết nối USB chổ nào ? Cổng dùng điện thế 220V được ko ? Nhiều thắc mắc khác nửa .
Thinks for this video
Pls describe what type of amp is this..looks like an attempt to turn 12 dc to 240vac stepup voltage booster into an audio amp which is ridiculous ,it simply doesn't have the current to push large 8ohm speaker well
Good luck friend
Thank friend
Please sharing diagram skema
Hey bro, this system doesn't burn the speaker?? Because from what I understand the transformer is playing 220v on the speaker, isn't that dangerous??
Better to connect 240 volt directly to the sub woofer and trying to connect with your phone. Surely you will feel the dance bar with fog and louder music😋😋😋😋
Trong như clip của anh thợ điện....nhận định từ bàn tay và móng cắt sát...
Thì là kênh của nó chứ ai
Very very nice . Bro
If you put some hot glue between transistors and radiator, you get up to 45Kw
Good ide perfect God Bless
Tem que usa toda potência do Alto falante por ele pra pular até queimar kkkkkkkkk aí sim e brabo , mas fico toop brabo esse trabalho da hora
Wow galing naman po
Super top demais parabéns 👏👏👏
Si funciona comprobado, la onda se amplia, a eso nos referimos a la frecuencia.
Better use mosfet transistors for transformer type boosters
Thanks for sharing this video,your creations are good,but there's No volume control.♥️👍
yep, I will improve in the next videos
Good
Booster sir lang yan
An AMAZING work 😊👍
💯 Excellent 💥
Tá tudo errado este capacitor não é de 2.5 micro......é de 2.2 micro o de 2.5 tá escrito nele 255..
good and simple amplifier circuit. but without any form of crossover or tone control, it will be fullrange, not a bass amp.
Just add a Bass equalizer and it becomes an ultra bass amplifier
The input signal is where you choose that.
Brigadier. J g vincule :-) URI yo Ojeda TFT y
booster type amplifier
He was controlling the volume through his mobile.
MUY INTEREZANTE ESTE PROYECTO Y MUY SENCILLO YO TENGO VARIOS MOSFET 38N30 Y QUISIERA FABRICAR UN AMPLIFICADOR CON ELLOS PERO NO EH PODIDO ENCONTRAR UN MODELO PARA YO REALIZARLO SI USTED ME PUEDE AYUDAR LE ESTARE MUY AGRADECIDO
El vídeo es falso la mayoría son falsos 8:46 ah se puede ver cómo tiene el Bluetooth activado el amplificador es la batería si quiere hacer un amplificador con mofets busque el diagrama por internet no crea en estos video gracias
This would work better if the speaker was connected across the 2 12v windings instead of the 220v one...and just leave the 220v unconnected, connecting to the 220v side is loading the amp down way too much and you are losing power. Doing this and running into 1 ohm you could get up to 200 watts RMS with a 12 volt supply (assuming the transistors can take the current)
Can you make a demo for it, really need it to enhance my TV audio tnx much.
And assuming you have a Power Supply capable of supplying ~16 Amps! which lets face it, most wont!
The thing is he made a booster amplifier instead a normal amplifier that's why he use transformer awesome..
Min, can I use a 12 volt adapter to play?
Yes. You can use 12v from adapter
رائع ممكن تستخدم محولات عدد 2 وسماعات عدد 2 لصنع الستريو
Untuk amplifier TOA masjid cocok banget itu..."
Bisa di tiru brooo
perlu di coba nih.....
yan ang gusto ko sa nag di diy di gaaya ng iba fake ang mga gawa.
mas aku warai lebih detailnya mas,suwun ,salam dr jepara
Giá bao nhieu tien 1 bộ vậy shop?
this is a brilliant idea
Waow the best brow i like
blue wire - 12v?
without any rectification?
So good my brother
Ok, onde tá o ultra Bass 3800w?.
Nem se for 3800watt de pico, e se é ultra Bass pq tem tanta voz?. Te desafio à fazer um vídeo real!
POR FAVOR SRES DE BRICOLAJE TECNICO; YO HICE UN CIRCUITO IGUAL A ESTE DE 3800 W PERO LE PUSE EL AUDIO Y NO SUENA NO HAY SALIDA DE AUDIO: SI ME INFORMAN QUE PUEDO HACER PARA SACAR LA SALIDA DE AUDIO SE LOS AGRADECERÍA GRACIAS
Los grigos ai artriba dicen q ese circuito es mentira, no funciona.
Mantep bos ngebas banget ya
KEREN 👍 KELUAR MURNI PMPO BERAPA WATT? APAKAH INPUT DC 12 V BISA PAKAI POWER SUPLAY 12 V DC ?
12/12 is AC or DC power
thank you
AC alternating -12 0 +12.
Transformer coupled amplifier, it is better if there is schematic diagram
Mantap abang,,
sy ingin belajar rakit
Nggak usah,kejebol nantinya,..rakitan itu sangat merbahaya pda hape jika anda tidak menggunakan tipe c adaptor seperti divideo kerna kabel phone audionya disambung terus pda sumber daya baterinya...It's Very risky on your mobile phone🔥AWAS!!!💥...
Mantap power nya jos👍
Có lan can huyền thoại mới nhận ra anh thợ điện
haha anh thợ điện nhiều kênh lắm. có khi xem bác xem video của em nhiều rồi nhưng không biết là em làm đấy
The cool my friend.. Cool.
Mantap 👍
Salam kenal
Sebenarnya. Banyak perangkat yang di buat China. Hampir semua kit. Ada. Sudah bagus murah dan mudah. Merakitnya. Hasil ok punya cuy.. Saya dulu sering buat. Sekarang sudah bosan. Banyak toko elektronik menyediakan. Kit. Yang cakep dan ok. Punya. Murah meriah dan jossss
Good instrumental music..who is name band playing music instrumental
10 Gostei bem simples mas eficiente!
Bom dia o transistor esquenta muito
Eii mano esse sistema aii não queima o auto falante?? Pq pelo q eu entendi o transformador tá jogando 220 v no alto falante isso não é perigoso??
Se fosse simples assim transformar 12v em 220v não existiria inversor.
Cara isso não é um alto falante de 2500 watts nunca, primeiro pelo tamanho do conjunto magnético, e segundo todos os vídeos que você faz, você nunca deixa o adesivo original do alto falante, sempre tira as informações do alto falante, e vem e escreve a mão a quantidade de watts que quiser no alto falante e quarto , podem reparar é sempre o mesmo alto falante velho e sujo, nunca é um bom alto falante cone seco ou borrachudo.
Are you sure the 2sc5200 is a Mosfet I looked and it says it is a BJT do you have a link to the datasheet
Fine Video
Mantap bang
Reandy kah bang
Itu spekear nya berapa inci bang
Sy speker aktif jikalau volumex n bas juga d fullin sekitar setengah jam da bunyi grek gitu boss,tapi basx d tutup bunyi grekx gak lagi
Its a booster not audio amplifier False theory