Hey Guys, I might gave you a misleading information in this video, at least for this oscilloscope, it really applies to other oscilloscopes regarding the size of the USB pen/partition. I tested today (should it have done before the video, but better late than never) and at least for my Kingston 16GB I was able to format it with FAT32 filesystem in one 16GB partition. I had the 4GB problem with other oscilloscopes and since this one requires the FAT32 to work (i tested with a 128GB NTFS USB pen and went nuts, had to reboot it) I assumed that will have also to be max 4GB, it doesn't. Sorry for this misleading information, it will work anyway, just its not a requirement. Well if formated in windows 10 and I tested up to 16GB pen.
Since the method of upgrading 2C10 to 2D15 was released, the firmware release has been stopped on the official homepage. Thank you for providing after-sales service as well as recommending the product.
Hugo, parabéns pelo excelente vídeo. Eu estava aguardando ansiosamente por essas dicas. Vamos ver se agora consigo fazer a atualização do meu DSO 2D10. Obrigado por compartilhar seus conhecimentos conosco.
Olá Sérgio, estive a verificar novamente e aparentemente o Windows 10 permite FAT32 em partições maiores de 4GB, testei e funcionou no osciloscópio. Mantem-se a questão de ser FAT32. Tenho aqui outros que não dá mesmo se não for 4GB max, mas este aparentemente aceita mais. Peço desculpa por esta informação "errada", quer dizer funciona na mesma mas pelo menos até 16GB não é preciso particionar, só formatar a FAT32. Obrigado por assistires! 👍
Maybe you don't know this, but fat 32 is not limited to 4gb partition size. I still make huge fat32 partitions. I used a 120gb ssd in a USB case for the firmware. However I would be limited to 4gb for a single file size.
Hi! Totally right, I messed up with the requirements of the Rigol devices I have here where if you want to mess with them, the USB pen must be formated with FAT16. Anyway, thanks for the heads up and for watching! 👍
Hi, thanks for the clear and comprehensive video, I'm writing to you from Italy, if you can help me I have a Hantek DSO2C10 that starts but then freezes after it has run the hardware check. the commands don't respond and I don't see any traces, only channel 1 remains on, what could have happened? is there a reset maneuver? thanks for your answers. Greetings.
Very very good video, thanks a lot. in the Hantek Website there are a few downloads. The firmware, which you have shown us in this video, the manual, but also a file called "DSO2000 Software", is this for the PC I assume?, do you have it installed in yours?
Hey Carlos! Yes, I did install the PC software, you have a oscilloscope PC terminal and arbitrary wave builder/editor. You can take a look on the PC software in this review video I made ( th-cam.com/video/2xRvbORAahM/w-d-xo.html ), I show there how they work. Thanks for watching! 👍
Excellent video! But I have a doubt. Please, can you check for me if it is possible to measure the phase angle between two sinusoidals with this equipment? That is, what is the phase angle between channels 1 and 2 when both channels have a sine wave, but the frequencies of channels 1 and 2 are different? Does it do this measurement automatically? Thanks.
Hi Roney, personally I never done that. Didn't have that need. But I'm not aware of any special "feature" to do that, if you can do it with cursors, you're safe, other than that can't garantee that you can use it for that kind of measure. Thanks for watching.
Thanks for this video! Have you tested if this upgrade made improvements to the low voltage accuracy issue that you mentioned about this scope in the previous comparison video you made?
Hey Jeff, not yet, I'm preparing a video to check that and also do a speed test using a TDR to measure the rise times and so on. Just need to organize here the time to make it. Will be soon. Thanks for watching. 👍
After an FW upgrade you should do a calibration too: waiting at least 30mins turned on and then proceeding with the calibration, sometimes a probe adjustment may be needed too.
Hello, I don't know why, but he removed the post with all the stuff for DSO2000 from the EEVBlog, maybe people was always asking stuff or Hantek reach him to do that, anyway, it is a pitty. He was doing more support to the DSO2000 that Hantek does. Thanks for watching! 👍
Hello Hugo! Thanks for this video. I am thinking whether to buy this oscilloscope or the owon sds1102. Can you make a video where you verify if the bugs persist or if they were eliminated after the firmware update? Greetings from Argentina.
Hi Agustin, my next video will be about this oscilloscope, it will release in the next days, so stay alert, One of the things that I will test is if the upgrade solves the issues I found in the first review video I made and in the showdown video. Thanls for watching! 👍
Set up my new 2C10 and it didn't work very well. Measurements were incorrect and response was sluggish. I installed the latest firmware update and it worked just fine. I'm wondering if some of these units are programed with a test edition of the firmware and not the final retail version. The firmware update should be the first item in the manual, not on the back pages. Thanks for the video, big help.
Hi James, I was really glad when I read this, is always good when the video helps someone. Glad I could help and thanks a lot for watching the video and your comment! Kudos 👍
Hey David, the first models, I think it was just a software thing, even the bandwidth, I even have the code to "upgrade" the oscilloscope, but talking with Paul from Learn Electronics channel, he told me that the latest units are missing some components that will allow the AWG functions, so I thing this is a "it depends" issue, if you have those components on the board, you'll probably be able to "upgrade" your unit. Thanks for watching. 👍
@@TechCornerTV I just bought a 2c10. The relay and everything appears to be there. I flashed the firmware and added the txt file in root of folder but all it did was update the firmware no awg even though it looks to be populated
Hi, the author of the software and different options removed it from the eevblog, you have on the first sticky post the link for the web archive, where you can download it. Sorry the so late reply, trying to catchup with the comments. Thanks for watching.
I am starting to make up my mind to buy this oscilloscope but after seeing your comparison video I am a bit confused. I mainly will be using this oscilloscope for voltage ripple measurements in mV. Can you please let me know whether it will be able to measure ripples in the range of 20mV-50mV? It will be extremely helpful for so many of us if you can make a video on it too.
Hey there, my next video will be about this oscilloscope, I was not able to recorder yesterday, I gonna try to record during this weekend, and I'll try to cover that voltage ranges in the new tests. Thanks for watching! 👍
@@TechCornerTV Thank you very much, really appreciate it. Voltage ripple test was nowhere to be found on youtube but glad I will finally be able to find proper info through your channel :)
Hello! Sorry for late reply, house move and vacations. Yes, the upgrades solved most of the issues. You can see my latest video on this oscilloscope, it's there. Thanks for watching!
Hi, well, that seems a bit out of the scope of the oscilloscope, if you know in which device the "buzz" is, you might use it or a multimeter to find out which component is doing that, but generally speaking find which device is doing that, I really don't know if that's possible. Sorry. Thanks for watching.
Hola, tengo un 2D15 y he notado una sustancial diferencia en la ganancia de uno y otro canal, condición que empeora a altas frecuencias ( 100/150 mhz, de hasta una división, ambos canales con la misma sonda y seteo, aclaro que antes de las pruebas se corrió el menú de calibración, y que el osciloscopio está actualizado al último firmware disponible a la fecha. No se si habrá algún control interno que pueda corregir el problema, o habrá que esperar nueva actualización.
Hola Marcelo, sorry for writting in english, I can read spanish, but I am unable to create sentences... the DSO2000 seems to have some problems with measurements. While using both channels you'll have only 500MSa/s of sampling rate, not 1 GSa/s, not sure if that will be a reason for what is happening there, shouldn't. Anyway, it might be only a factory problem. Did you try to reach the Hantek support about that problem? Thanks for watching! 👍
@@TechCornerTV Muchas gracias por responder, yo te leo con el traductor de google. Una aclaración más, las pruebas se realizaron habilitando 1 canal por vez, precisamente para mantener 1 GSa/s en cada testeo. Saludos!
Pon en google "dso2d10 firmware" o el modelo que tengas y te aparece como primer resultado la web de hantek. Una vez en la web de hantek, le das click donde dice "DSO2000" lo que inicia la descarga de un archivo ZIP Luego descomprimes ese archivo que resulta ser una carpeta con un archivo ".upk" TOmas ese .upk y lo pones en un pendrive que luego conectas al osciloscopio y sigues los pasos del video en 6:23 (PD: el archivo desde hantek es generico para varios modelos DSO2.... por ende no te preocupes que el sistema automaticamente toma lo que le pertenece a tu modelo)
Hi, the author of the referred scripts and firmware deleted the post from EEVBlog, but I added to a sticky post on the top of the comment of this video, the URL for web archive were you can still find them 😁 thanks for watching!
Recently purchased this scope, and the software is 20210726. I see on the Hantek site it is up to 20211231. When I try to install the new software the scope sets error code 3. Any ideas what may be the problem?
@@TechCornerTV Got it ! It was formatted to FAT already, but reset and was able to update software, Thanks SO much. Now, the next problem, is connecting to PC. Have the app installed, and shows device not connected. Does not show in USB devices when connected, even tried different cord. Any ideas?
@@scrappy7571 Make sure the USB driver is installed, the oscilloscopes need a "special" USB driver that is common to all of them, specially those entry level ones. The driver, I think, is provided with the CD or is on the website, can't remember.
Hi there, I found your video very useful but when I tried to update the firmware on my DSO5102P scope it said it did not recognize the .rar file that I downloaded from the Hantek site. There are no .UPK files there to download. So far I have had no reply from Hantek. The file I downloaded for my scope was: dso5kp_func_dso5102p20210225.rar Any thoughts? Thanks
Hi Julian, this tutorial is for the DSO2000 series but I believe the procedure should be the same. If you look carefully in the video, I did *UNRAR* (unzip) the "rar file" to a directory, you should be able to do it with the 7-Zip a free windows app for that and the .UPK file appears after you unrar/unzip the file you downloaded. Let me know if you have any more issues and I'll try to help. Thanks for watching 👍
@@TechCornerTV Hi again, the same problem. I used a Windows 11 unzip program (7-Zip) and the resulting folder had a file ending in .up and not .upk. I put it on my 3Gb partitioned FAT32 thumb drive and again it said there were no firmware files on it.
![ลองสุ่มไอโฟน 990 โกงมั้ย? [ โกงมั้ยครับ ep.101 ] | DOM](http://i.ytimg.com/vi/bfsWe0j492k/mqdefault.jpg)
Thank you so much for the easy to understand, step-by-step instructions. I just upgraded to 20240326, 1.0.3 firmware in just a few minutes.
Hey Guys, I might gave you a misleading information in this video, at least for this oscilloscope, it really applies to other oscilloscopes regarding the size of the USB pen/partition. I tested today (should it have done before the video, but better late than never) and at least for my Kingston 16GB I was able to format it with FAT32 filesystem in one 16GB partition. I had the 4GB problem with other oscilloscopes and since this one requires the FAT32 to work (i tested with a 128GB NTFS USB pen and went nuts, had to reboot it) I assumed that will have also to be max 4GB, it doesn't. Sorry for this misleading information, it will work anyway, just its not a requirement. Well if formated in windows 10 and I tested up to 16GB pen.
Since the method of upgrading 2C10 to 2D15 was released, the firmware release has been stopped on the official homepage.
Thank you for providing after-sales service as well as recommending the product.
Hi! No problem, my pleasure! Thanks for watching and you nice support comment 😁👍
Hugo, parabéns pelo excelente vídeo. Eu estava aguardando ansiosamente por essas dicas. Vamos ver se agora consigo fazer a atualização do meu DSO 2D10. Obrigado por compartilhar seus conhecimentos conosco.
Olá Sérgio, estive a verificar novamente e aparentemente o Windows 10 permite FAT32 em partições maiores de 4GB, testei e funcionou no osciloscópio. Mantem-se a questão de ser FAT32. Tenho aqui outros que não dá mesmo se não for 4GB max, mas este aparentemente aceita mais. Peço desculpa por esta informação "errada", quer dizer funciona na mesma mas pelo menos até 16GB não é preciso particionar, só formatar a FAT32. Obrigado por assistires! 👍
Thanks for this guide, updated my unit today without issue
Hi Sean, great to hear! Thanks for watching! 👍
I have been wanting to do this, so thx for the tutorial! Do u know what the new firmware changes from the previous?
Hey Jay, sorry but no, unfortunaly I didn't found a change log, I don't even know if they have one. Thanks for watching! 👍
Maybe you don't know this, but fat 32 is not limited to 4gb partition size. I still make huge fat32 partitions. I used a 120gb ssd in a USB case for the firmware. However I would be limited to 4gb for a single file size.
Hi! Totally right, I messed up with the requirements of the Rigol devices I have here where if you want to mess with them, the USB pen must be formated with FAT16. Anyway, thanks for the heads up and for watching! 👍
Hi, thanks for the clear and comprehensive video, I'm writing to you from Italy, if you can help me I have a Hantek DSO2C10 that starts but then freezes after it has run the hardware check. the commands don't respond and I don't see any traces, only channel 1 remains on, what could have happened? is there a reset maneuver? thanks for your answers. Greetings.
Very very good video, thanks a lot. in the Hantek Website there are a few downloads. The firmware, which you have shown us in this video, the manual, but also a file called "DSO2000 Software", is this for the PC I assume?, do you have it installed in yours?
Hey Carlos! Yes, I did install the PC software, you have a oscilloscope PC terminal and arbitrary wave builder/editor. You can take a look on the PC software in this review video I made ( th-cam.com/video/2xRvbORAahM/w-d-xo.html ), I show there how they work. Thanks for watching! 👍
Thanks for the guide. Is the oscilloscope still freezing sometimes?
Hey Rick, latelly no. But to be honest, my main oscilloscope is the Rigol, is where I do most of my tests. Thanks for watching! 👍
Excellent video! But I have a doubt. Please, can you check for me if it is possible to measure the phase angle between two sinusoidals with this equipment? That is, what is the phase angle between channels 1 and 2 when both channels have a sine wave, but the frequencies of channels 1 and 2 are different? Does it do this measurement automatically? Thanks.
Hi Roney, personally I never done that. Didn't have that need. But I'm not aware of any special "feature" to do that, if you can do it with cursors, you're safe, other than that can't garantee that you can use it for that kind of measure. Thanks for watching.
Thanks for this video! Have you tested if this upgrade made improvements to the low voltage accuracy issue that you mentioned about this scope in the previous comparison video you made?
Hey Jeff, not yet, I'm preparing a video to check that and also do a speed test using a TDR to measure the rise times and so on. Just need to organize here the time to make it. Will be soon. Thanks for watching. 👍
Awesome! I look forward to watching it. Thank you.
Thank you for letting me know where to find hantek firmware update file! 23.07.26(수)
Hi, you are welcome and thanks for watching.
After an FW upgrade you should do a calibration too: waiting at least 30mins turned on and then proceeding with the calibration, sometimes a probe adjustment may be needed too.
Hey there, you're totally right.... I did forgot to mention that. I'll take notice to my next video. Thanks! And thanks for watching 👍
David Alfa is from eevblog forum and he not only assembled a lto of stuff, bit he also developed some of the tools.
Hello, I don't know why, but he removed the post with all the stuff for DSO2000 from the EEVBlog, maybe people was always asking stuff or Hantek reach him to do that, anyway, it is a pitty. He was doing more support to the DSO2000 that Hantek does. Thanks for watching! 👍
Hello Hugo! Thanks for this video. I am thinking whether to buy this oscilloscope or the owon sds1102. Can you make a video where you verify if the bugs persist or if they were eliminated after the firmware update? Greetings from Argentina.
Hi Agustin, my next video will be about this oscilloscope, it will release in the next days, so stay alert, One of the things that I will test is if the upgrade solves the issues I found in the first review video I made and in the showdown video. Thanls for watching! 👍
Set up my new 2C10 and it didn't work very well. Measurements were incorrect and response was sluggish. I installed the latest firmware update and it worked just fine. I'm wondering if some of these units are programed with a test edition of the firmware and not the final retail version. The firmware update should be the first item in the manual, not on the back pages. Thanks for the video, big help.
Hi James, I was really glad when I read this, is always good when the video helps someone. Glad I could help and thanks a lot for watching the video and your comment! Kudos 👍
Hi, I have only one question I have the Hantek 150Mhz without the AWG can you initialize AWG which looks like it is software enabled.
Hey David, the first models, I think it was just a software thing, even the bandwidth, I even have the code to "upgrade" the oscilloscope, but talking with Paul from Learn Electronics channel, he told me that the latest units are missing some components that will allow the AWG functions, so I thing this is a "it depends" issue, if you have those components on the board, you'll probably be able to "upgrade" your unit. Thanks for watching. 👍
@@TechCornerTV I just bought a 2c10. The relay and everything appears to be there. I flashed the firmware and added the txt file in root of folder but all it did was update the firmware no awg even though it looks to be populated
ham radio hack Hi, curious if you've had any success getting that AWG function? I've just ordered a 2C10 in the hopes. Thanks
@@derekec yes
@@derekec Hi Derek I have not tried as yet no quite brave enough to give it a go.😄
Hi please, is this scope good for serial decode? I decide to buy one... thanks :)
Hi Maros, yes it is. If you decide to buy, please use the affiliate link, will help a lot. Thanks for watching 👍
Thanks! excellent guide.
Hey Tron, glad you liked it! Thanks for watching 😁
I see no links to that firmware that work. Can you put a working link in here? Thanks
Hi, the author of the software and different options removed it from the eevblog, you have on the first sticky post the link for the web archive, where you can download it. Sorry the so late reply, trying to catchup with the comments. Thanks for watching.
I am starting to make up my mind to buy this oscilloscope but after seeing your comparison video I am a bit confused. I mainly will be using this oscilloscope for voltage ripple measurements in mV. Can you please let me know whether it will be able to measure ripples in the range of 20mV-50mV? It will be extremely helpful for so many of us if you can make a video on it too.
Hey there, my next video will be about this oscilloscope, I was not able to recorder yesterday, I gonna try to record during this weekend, and I'll try to cover that voltage ranges in the new tests. Thanks for watching! 👍
@@TechCornerTV Thank you very much, really appreciate it. Voltage ripple test was nowhere to be found on youtube but glad I will finally be able to find proper info through your channel :)
Does this upgrade solve the v/division freeze issue?
Hello! Sorry for late reply, house move and vacations. Yes, the upgrades solved most of the issues. You can see my latest video on this oscilloscope, it's there. Thanks for watching!
Hello,
There is a high pitched frequency noise in my home. I believe it is a "mosquito" device. What can I use to find it? Thank you!!
Hi, well, that seems a bit out of the scope of the oscilloscope, if you know in which device the "buzz" is, you might use it or a multimeter to find out which component is doing that, but generally speaking find which device is doing that, I really don't know if that's possible. Sorry. Thanks for watching.
@@TechCornerTV What about a scope and a directional microphone?
Thank you very much.
Hi, You are welcome! Thanks for watching 👍
Hola, tengo un 2D15 y he notado una sustancial diferencia en la ganancia de uno y otro canal, condición que empeora a altas frecuencias ( 100/150 mhz, de hasta una división, ambos canales con la misma sonda y seteo, aclaro que antes de las pruebas se corrió el menú de calibración, y que el osciloscopio está actualizado al último firmware disponible a la fecha. No se si habrá algún control interno que pueda corregir el problema, o habrá que esperar nueva actualización.
Hola Marcelo, sorry for writting in english, I can read spanish, but I am unable to create sentences... the DSO2000 seems to have some problems with measurements. While using both channels you'll have only 500MSa/s of sampling rate, not 1 GSa/s, not sure if that will be a reason for what is happening there, shouldn't. Anyway, it might be only a factory problem. Did you try to reach the Hantek support about that problem? Thanks for watching! 👍
@@TechCornerTV Muchas gracias por responder, yo te leo con el traductor de google. Una aclaración más, las pruebas se realizaron habilitando 1 canal por vez, precisamente para mantener 1 GSa/s en cada testeo. Saludos!
Thanks a lot!!!
Hi. You're welcome! Thanks for watching.
Hola no consigo descargar el archivo de drivers, podrias resubirlo
Hola! Sorry, can read spanish, but can't write. Take a look in the Hantek website, support and downloads. Is there for download. Thanks for watching.
ok
@@TechCornerTV
gracias
Pon en google "dso2d10 firmware" o el modelo que tengas y te aparece como primer resultado la web de hantek.
Una vez en la web de hantek, le das click donde dice "DSO2000" lo que inicia la descarga de un archivo ZIP
Luego descomprimes ese archivo que resulta ser una carpeta con un archivo ".upk"
TOmas ese .upk y lo pones en un pendrive que luego conectas al osciloscopio y sigues los pasos del video en 6:23
(PD: el archivo desde hantek es generico para varios modelos DSO2.... por ende no te preocupes que el sistema automaticamente toma lo que le pertenece a tu modelo)
You are king!
Hi! Thank you so much for you kind comment and for watching! 👍
Hi, what is the size of the .upk file you downloaded? Mine is showing as 1,866kb which seems a little small? Thanks.
Hey Dave, yeap, thats it. I upgraded my unit on tuesday with success. Thanks for watching! 👍
@@TechCornerTV Great, thank you 👍
the link to the firmwares is not working
Hi, the author of the referred scripts and firmware deleted the post from EEVBlog, but I added to a sticky post on the top of the comment of this video, the URL for web archive were you can still find them 😁 thanks for watching!
@@TechCornerTV ok I'll check it out and let you know. Thanks for sharing
👍👍👍👍👍👍👍👍👍👍
Hi Paulo, thanks for watching! 👍
Recently purchased this scope, and the software is 20210726. I see on the Hantek site it is up to 20211231. When I try to install the new software the scope sets error code 3. Any ideas what may be the problem?
Hello Scrappy, did you formated the pen to FAT32? Not, FTFS or exFAT. Thats the only thing I see that might be problematic. Thanks for watching. 👍
@@TechCornerTV Got it ! It was formatted to FAT already, but reset and was able to update software, Thanks SO much. Now, the next problem, is connecting to PC. Have the app installed, and shows device not connected. Does not show in USB devices when connected, even tried different cord. Any ideas?
@@scrappy7571 Make sure the USB driver is installed, the oscilloscopes need a "special" USB driver that is common to all of them, specially those entry level ones. The driver, I think, is provided with the CD or is on the website, can't remember.
@@TechCornerTV Yes, the driver is installed, or at least I think it is. Def missing something. WOW they sure don't make this plug and play...
@@TechCornerTV Keysight app re-installed, and does not show any equipment connected. At a loss here, any ideas? Thanks.
Hi there,
I found your video very useful but when I tried to update the firmware on my DSO5102P scope it said it did not recognize the .rar file that I downloaded from the Hantek site. There are no .UPK files there to download. So far I have had no reply from Hantek. The file I downloaded for my scope was: dso5kp_func_dso5102p20210225.rar Any thoughts? Thanks
Hi Julian, this tutorial is for the DSO2000 series but I believe the procedure should be the same. If you look carefully in the video, I did *UNRAR* (unzip) the "rar file" to a directory, you should be able to do it with the 7-Zip a free windows app for that and the .UPK file appears after you unrar/unzip the file you downloaded. Let me know if you have any more issues and I'll try to help. Thanks for watching 👍
@@TechCornerTV Thanks. I used Apple Macs unzip and it produced another .rar file with an extra extension. I will try and find ‘Unzip’ or ‘Unrar’.
@@TechCornerTV Hi again, the same problem. I used a Windows 11 unzip program (7-Zip) and the resulting folder had a file ending in .up and not .upk. I put it on my 3Gb partitioned FAT32 thumb drive and again it said there were no firmware files on it.