Mano, eu atualizei meu taranis qx7 pro open tx, a penúltima versão, e atualizei meu xm+ pra última verão também, mas não consegui bindar de jeito nenhum, pode tentar me ajudar?
boas tems a certeza que tems os dois em fcc outra pergunta afastaste o radio do receiver se tiver bem perto a luz verde não acende o edrone pediu me para vir aqui porque ele na fala portugues
I just got an aircraft that had the XM+ in it. WOULD NOT BIND. I ended up flashing the firmware to make it compatible with my QX7. THEN with the help of this vid, I finally got it all to work. Thank you for this vid !
Thanks for the video. I also have a XM+ and X7. Lights stayed red/green, flashing new version (2.0.2) did not help. But an older firmware version did work! (XM+170313) On the receiver it reads: "XM Plus V4.1 20151009". Maybe this info helps someone else.
Hey Edrone i put in a brand new xm+ receiver into my taranis qx7 for my HGLRS Arrow3 4s and the green light and the red light come on but while holding the bind button and when i repower the quad i get only red lights on my xm+ reciever?It will not arm and the receiver will not respond? Can you tell me why this is happening?
wracam jak tylko zapomnę - wytłumaczone wolno i dobrze - jak krowie na rozdrożu ,trzeba by być krową żeby tego nie pojąć ....I come back as soon as I forget - explained slowly and well - as we use to say: like a cow at a crossroads, you'd have to be a cow not to understand ...
I bought this reciever for my first build. It never lit up when powered. Went to check and see if it was getting power with ohm meter and accidentally touched the 5v connection to the ground. All lights on the fc went off instantly. Now fc will work when powered by usb but nothing when connected to battery. I guess maybe fried whatever regulates the power on the fc. Anyways, ordered new fc and receiver. Can i solder the new reciever to the new fc and power it with usb and bind it before connecting it to a battery or does the reciever need to be powered by a battery?
Depends on the flight controller and your PC USB port some will pass enough voltage to power receiver, and some wont I would say try it with USB first and if your receiver does not show activity in the receiver tab then you will need to use lipo to power up the receiver
I think it's bound but now but I've got a flashing a green light on the transmitter but can't arm it. I'll hit you up later in the week. Thank you so much brother!!!👍
Hey man I got my xm+ to bind but when I first power on I get the flashing red to green lights then it will randomly switch from solid green to solid red and back to solid green. I also get no response from the tx in betaflight. Any suggestions?
Norcorider209 you may need to flash the receiver with different firmware the tara taranis is capable of doing this you have to hook up your taranis to your PC load the firmware to your taranis FCC in the USA CE everywhere else then you hook your taranis to your receiver and flash firmware you will need to make a cable though to connect to your receiver and to your transmitter
edrone this is actually the 2nd receiver I’ve tried I had solid red and green on the first one. Set up a servo cable for the smart port to flash it but I would get a bottom pin no response error. The new one bound no problem but does that funky shit. I’ve had a rooster built for 3 weeks that I can’t get into the air. I have been extremely discouraged by it. I guess I have a cool paper weight though.
edrone from left to right on the smart port gnd 5v s. I flashed it with 170313 rssi 16 a little bit ago and everything seems to work good now! Solid green light and no more switching to red. My computer crashed on me a few days ago and all my buddy’s with betaflight are out of town until tomorrow so I’ll have to wait on that.Thanks man I appreciate it.
Hello, If you done this got it to bind and it turned green and everything,but you go to set up arming in betaflight but its not recognizing the qx7. What could that be. My buddy got a qx7 and xm plus from my other buddy and its doing this.The only thing i can think is maybe he didnt set up a completely new model on the qx7 and hes trying to use the model that was already on it when he got it. Any info would be greatly appreciated.
Though if he is trying to use an existing model that was on the qx7 when he got it and creating a new model with his quad/fc could this be or cause problems?
My bind was successful. But when I plug into betaflight the receiver tab isn't picking up stick inputs? Someone help please. This is my first drone. Thanks
Try unplugging power couple times while the receiver tab is open also do you have the correct uart enabled for your serial rx in the ports tab plus make sure to select serial based receiver and sbus in the configuration tab
for some reason on the drone it has a green light but the controller has no indication if biend connected and when i plug it in to betaflight it says nothings connected but the light is still green pls help
Doesn't work for me. :( When I start the quad regularly it flashes red and when I push the button on the transmitter while powering it up it light green and red up without flashing and so it doesn't bind to my QX7. Anyone help?
What firmware does it have? And where are you located? You want to make sure you have the correct version of firmware for your location example eu for outside United States or fcc for United States
ITS NOT WORKING IVE TRIED FOR SO LONG ON GETTING MY RECEIVER TO TURN GREEN HOW DO I DO IT. NOW IT FLASHES GREEN WHEN I TRY TO BIND IT. WHY!!!!!!!!!!!!!!!!!
Sorry my friend you are having trouble you have to make sure the bind button is pushed down all the way while you power it up sometimes it may feel like its depressed but it may not be you may want to get someone to help you out as it's very difficult by yourself
If you have access protocol you need to register the receiver by holding down on the bind button and clicking on register on your transmitter once you do that you will then power cycle then will click bind on your radio And then power up your receiver And complete the buying process by pushing OK on the transmitter
@@edrone_ that's what I am doing. I put it on Mode: Accst D16 ch.Range CH1-8 but the red and green light keep being solid they don't blind or give any sign that its binding.
Can anyone help with my issue? I have a taranis qx7 and my receiver is a FrSky xm plus. They are bound, the light is green, but it does not move anything. It is on a lumenier lux v2 fc. When I move the sticks, nothing happens on the motors or in Betaflight. Any ideas on what I am doing wrong? I have set my inputs and mixers also.
What do you have your receiver set to in the configuration tab? Also what uart is your receiver soldered to? Is that the same in betaflight you have to set the correct uart for your serial receiver
I have my Receiver set to Serial-based receiver and SBUS for Serial Receiver Provider. I have my receiver soldered to uart 4 which I have now enabled the Serial Rx under ports. I have not set peripherals to anything. It's on disabled and Auto. After all of this, I still cannot get a response with the Taranis. @@edrone_
Make sure you the bind button is clicking when you push and hold it down. It is very easy to think the button is pressed when it's actually not. Also depending on which firmware and protocol you are using on your radio can make a difference also. If you have a frsky receiver with access protocol firmware and your radio is not set to access it won't work either.
Skyler Ogden yes this was a video in which I was still learning editing obviously it drug out in the beginning watch my newer videos I have improved I think lol
![30 ชั่วโมงคนเดียว บนรถไฟชั้น 3 โซเวียต [Around The World Ep. 2]](http://i.ytimg.com/vi/MlE9boAVqDA/mqdefault.jpg)
![[Full] 4 ต่อ 4 Celebrity EP.920 | 3 พ.ย. 67 | one31](http://i.ytimg.com/vi/KwiW2M_kAg4/mqdefault.jpg)
Mano, eu atualizei meu taranis qx7 pro open tx, a penúltima versão, e atualizei meu xm+ pra última verão também, mas não consegui bindar de jeito nenhum, pode tentar me ajudar?
boas tems a certeza que tems os dois em fcc outra pergunta afastaste o radio do receiver se tiver bem perto a luz verde não acende o edrone pediu me para vir aqui porque ele na fala portugues
@@badugafpv76 meu qx7 é versão internacional FCC, e meu receptor baixei a última versão disponível na frsky, e o meu qx7 é accst
@@badugafpv76 e sim, eu deixo o controle afastado do receptor, 25-50cm
@@fpvislife6450 eu no meu tive que flashar a versão mais antiga
@@fpvislife6450 que luzes tems no xm + quando fazes o bind ?
Thanks! Awesome video. Manage to bind the Xm+ and Taranis Qx7 now for the first time, on my first build. :)
AirBuzz One no problem please like share and subscribe thanks for watching
I just got an aircraft that had the XM+ in it. WOULD NOT BIND. I ended up flashing the firmware to make it compatible with my QX7. THEN with the help of this vid, I finally got it all to work.
Thank you for this vid !
Thanks for your support glad you got straightened out!
Mind tossing me the link that you used? I can't seem to find any tutorials specifically for this radio.
Thanks for the video. I also have a XM+ and X7. Lights stayed red/green, flashing new version (2.0.2) did not help. But an older firmware version did work! (XM+170313) On the receiver it reads: "XM Plus V4.1 20151009". Maybe this info helps someone else.
Dude!! you saved my life.. Thank you very much, I've been trying to get it working for almost 24 hours! Thank you again
@@xLowYx Thats great! Took me a lot of time to figure it out, glad to hear it helped someone :). Have fun!
Hey Edrone i put in a brand new xm+ receiver into my taranis qx7 for my HGLRS Arrow3 4s and the green light and the red light come on but while holding the bind button and when i repower the quad i get only red lights on my xm+ reciever?It will not arm and the receiver will not respond? Can you tell me why this is happening?
wracam jak tylko zapomnę - wytłumaczone wolno i dobrze - jak krowie na rozdrożu ,trzeba by być krową żeby tego nie pojąć ....I come back as soon as I forget - explained slowly and well - as we use to say: like a cow at a crossroads, you'd have to be a cow not to understand ...
Great vid, thanks for sharing this.
build is looking good friend. I've already flown my alien a couple times.
Where did U connect the cables not Gnd and 5v talking about the sbus cable !myn the light just turn red and green and it didn’t blink! It stay solid !
th-cam.com/video/ZZty_fW3j9s/w-d-xo.html
I bought this reciever for my first build. It never lit up when powered. Went to check and see if it was getting power with ohm meter and accidentally touched the 5v connection to the ground. All lights on the fc went off instantly. Now fc will work when powered by usb but nothing when connected to battery. I guess maybe fried whatever regulates the power on the fc. Anyways, ordered new fc and receiver. Can i solder the new reciever to the new fc and power it with usb and bind it before connecting it to a battery or does the reciever need to be powered by a battery?
Depends on the flight controller and your PC USB port some will pass enough voltage to power receiver, and some wont I would say try it with USB first and if your receiver does not show activity in the receiver tab then you will need to use lipo to power up the receiver
Very helpful video.
I have done all this and my light is green but my drone will still not work. Any tips ?
Did you set up switches?
Thanks man I continue to use these videos vs memory!!! Cheers
I have this receiver for my Vortex 180. How hard was it to solder the three pin connector? Looks pretty small.
DRONE POOL not hard at all check out my xmplus install video
Very nice, mate. Do we need to flash the receiver before bind? Thanks 🙏🙏🍻🤟
It definitely does not hurt
@@edrone_ hehe thank you 🙏🍻🤟
Thanks Bud, think i need to update the version of FRSKY on the Furibee x215 Pro?! Lol
Damn think i've been pushing the wrong button maybe? The transmitter is sealed up.
I'LL BEE DRONED! If you can't get it email me and I'll give you my cell my email is emarvel09@gmail.com
I think it's bound but now but I've got a flashing a green light on the transmitter but can't arm it. I'll hit you up later in the week. Thank you so much brother!!!👍
Let's start with 2:00
Definitely learned alot since this video lol
Hey man I got my xm+ to bind but when I first power on I get the flashing red to green lights then it will randomly switch from solid green to solid red and back to solid green. I also get no response from the tx in betaflight. Any suggestions?
Norcorider209 you may need to flash the receiver with different firmware the tara taranis is capable of doing this you have to hook up your taranis to your PC load the firmware to your taranis FCC in the USA CE everywhere else then you hook your taranis to your receiver and flash firmware you will need to make a cable though to connect to your receiver and to your transmitter
edrone this is actually the 2nd receiver I’ve tried I had solid red and green on the first one. Set up a servo cable for the smart port to flash it but I would get a bottom pin no response error. The new one bound no problem but does that funky shit. I’ve had a rooster built for 3 weeks that I can’t get into the air. I have been extremely discouraged by it. I guess I have a cool paper weight though.
Norcorider209 where on the qx7 did you plug in your servo cable and when did you get the taranis qx7 transmitter?
edrone from left to right on the smart port gnd 5v s. I flashed it with 170313 rssi 16 a little bit ago and everything seems to work good now! Solid green light and no more switching to red. My computer crashed on me a few days ago and all my buddy’s with betaflight are out of town until tomorrow so I’ll have to wait on that.Thanks man I appreciate it.
Norcorider209 no problem glad to help please like share and subscribe thanks
Hello, If you done this got it to bind and it turned green and everything,but you go to set up arming in betaflight but its not recognizing the qx7. What could that be. My buddy got a qx7 and xm plus from my other buddy and its doing this.The only thing i can think is maybe he didnt set up a completely new model on the qx7 and hes trying to use the model that was already on it when he got it. Any info would be greatly appreciated.
Loyd Howard You could try updating the firmware on the XM plus receiver sometimes this will help
edrone Ok that's a great idea. Thank you very much.
Though if he is trying to use an existing model that was on the qx7 when he got it and creating a new model with his quad/fc could this be or cause problems?
Loyd Howard No problem please subscribe thank you
nice review
wich firmware did you have on the taranis and on the XM plus?
Im sure its on my playlist check it out!!
oops dont see it (thx🙃)
My bind was successful. But when I plug into betaflight the receiver tab isn't picking up stick inputs?
Someone help please. This is my first drone.
Thanks
Try unplugging power couple times while the receiver tab is open also do you have the correct uart enabled for your serial rx in the ports tab plus make sure to select serial based receiver and sbus in the configuration tab
Wich Firmware did i have to flash on the taranis and on the xm plus?
Depends on where your located
I live in germany
@@qurox9169 You will want the EU firmware for the xm plus
But i dont know where i can find it 😭
@@qurox9169 You will have to go to the frsky website and download from your computer on to your taranis and then flash using your qx7
for some reason on the drone it has a green light but the controller has no indication if biend connected and when i plug it in to betaflight it says nothings connected but the light is still green pls help
Check your ports tab and make sure the correct uart is selected for your receiver.
How would I do that?( I’m kind of new to the hobby)
@@explosionfpv did you build drone or did you buy it built?
I baught it built it’s the emax buzz
@@explosionfpv ok just need to see what number pad you used for your receiver for your signal wire
Whats the "buzzer" for?
Help locate model if lost and to alert when battery voltage is low
Doesn't work for me. :(
When I start the quad regularly it flashes red and when I push the button on the transmitter while powering it up it light green and red up without flashing and so it doesn't bind to my QX7.
Anyone help?
What firmware does it have? And where are you located? You want to make sure you have the correct version of firmware for your location example eu for outside United States or fcc for United States
you must hook up your reciver to you radio,and chanche the firmware!!,i go look on bardwel site he explane it good and simple!!good luck.
Had a friend help me install my receiver and he was able to bind it but no input from controls 😩 can anyone help me out xm+ on taranis qx7
Are you using sbus for receiver?
Yes used SBUS
Also tried other uarts and nothing, I did get crossfire nano to bind and get the quad flying but it just want with the Xm plus
Won’t *
Thanks.. You sound like you live near Philly lol
Delaware close lol
I'm in Delaware County.. I always recognize a local lol
thanks man
ITS NOT WORKING IVE TRIED FOR SO LONG ON GETTING MY RECEIVER TO TURN GREEN HOW DO I DO IT. NOW IT FLASHES GREEN WHEN I TRY TO BIND IT. WHY!!!!!!!!!!!!!!!!!
Sorry my friend you are having trouble you have to make sure the bind button is pushed down all the way while you power it up sometimes it may feel like its depressed but it may not be you may want to get someone to help you out as it's very difficult by yourself
instead of pressing the button can i invoke this via betaflight
As of now no, only some of the whoops that have the all in one boards can be put into binding mode via betaflight
Does this go the same if i have the taranis Qx7 access?
If you have access protocol you need to register the receiver by holding down on the bind button and clicking on register on your transmitter once you do that you will then power cycle then will click bind on your radio And then power up your receiver And complete the buying process by pushing OK on the transmitter
@@edrone_ that's what I am doing. I put it on Mode: Accst D16
ch.Range CH1-8
but the red and green light keep being solid
they don't blind or give any sign that its binding.
@@jousiff91 accst is not access
@@edrone_ The transmitter is Access but I put the mode on Accst D16. I have two options for the model mode: Access or Accst D16
@@jousiff91 what kind of receiver are you using
thx man+
Can anyone help with my issue? I have a taranis qx7 and my receiver is a
FrSky xm plus. They are bound, the light is green, but it does not move
anything. It is on a lumenier lux v2 fc. When I move the sticks,
nothing happens on the motors or in Betaflight. Any ideas on what I am
doing wrong? I have set my inputs and mixers also.
What do you have your receiver set to in the configuration tab? Also what uart is your receiver soldered to? Is that the same in betaflight you have to set the correct uart for your serial receiver
Thanks for the quick response. Later today I'll be able to check on the setup again. I'll have some answers later today. @@edrone_
@@mariomendoza9764 ok sounds good also to set your receiver up on the correct uart check the peripherals tab in betaflight
I have my Receiver set to Serial-based receiver and SBUS for Serial Receiver Provider. I have my receiver soldered to uart 4 which I have now enabled the Serial Rx under ports. I have not set peripherals to anything. It's on disabled and Auto. After all of this, I still cannot get a response with the Taranis. @@edrone_
@@mariomendoza9764 send me a close up pic of all the wires soldered up to your fc please send to my email emarvel09@gmail.com
Omg
What?
I don`t understand why is not working for me...
Make sure you the bind button is clicking when you push and hold it down. It is very easy to think the button is pressed when it's actually not. Also depending on which firmware and protocol you are using on your radio can make a difference also. If you have a frsky receiver with access protocol firmware and your radio is not set to access it won't work either.
Holy cow. Trim the first minute of this video. Wow.
Skyler Ogden yes this was a video in which I was still learning editing obviously it drug out in the beginning watch my newer videos I have improved I think lol
@@edrone_ what a dik
I did these steps 4 times and never worked for me
Make sure you have the correct firmware for your region fcc for USA and ce for anywhere else