Raymond Reach, very slow drive No codes

แชร์
ฝัง
  • เผยแพร่เมื่อ 23 ธ.ค. 2024

ความคิดเห็น • 20

  • @chuckvoss9344
    @chuckvoss9344 6 หลายเดือนก่อน +2

    Now that is some impressive detective work. I never would have thought that could even be a possibility.

  • @DarteyIsaac-z9o
    @DarteyIsaac-z9o 2 หลายเดือนก่อน +1

    Mr Raymond
    Pls Teach me how to diagnosis and troubleshooting of TCM FORKLIFT

  • @rashidabdulkadir8483
    @rashidabdulkadir8483 6 หลายเดือนก่อน

    I enjoy watching ur videos ❤️thanx

  • @masongray9046
    @masongray9046 6 หลายเดือนก่อน

    Great find a lot of head scratching 👍

  • @charliehustle2579
    @charliehustle2579 6 หลายเดือนก่อน +2

    How in the hell did you figure that out? Bravo 👏
    Usually they'll just rebuild those so how does the case get mixed up? Unless you guys ordered a reman one and they sent you one with a close but different casing

  • @Tapia-live
    @Tapia-live 6 หลายเดือนก่อน +2

    Couldn't you just order a sensor for an end rider?

  • @FlynRydeN
    @FlynRydeN 4 หลายเดือนก่อน

    Hello, all your videos inspire to progress in this area, i'm work on this 6 years before and we have so much work, can you recommend any model of picoscope for Gas-LP,Diesel, and electric forklift technician?, i work with Raymond, crown, Yale, Hyster, Toyota, and in some times with others brands in Mexico., can you have any book or fundaments to know to get better on this? thanks for all your videos.

  • @rogerthomas1982
    @rogerthomas1982 6 หลายเดือนก่อน

    Good catch. I wonder if the phase of the sensor signal changes as you rotate the sensor.
    I like this style sensor. So much easier to replace than a sensor bearing.

    • @marcushoffmann9819
      @marcushoffmann9819 6 หลายเดือนก่อน

      Are you working on Linde a lot? 😂😂😂😂 hate those bearings 😂😂

  • @bryanleverett2830
    @bryanleverett2830 4 หลายเดือนก่อน

    If you ever think about moving to the United States, I have a job waiting for you. We make great money working on lifts here. I don’t where your currently located, but your English is fantastic.

    • @forkliftgeek10
      @forkliftgeek10  4 หลายเดือนก่อน +1

      Thank you

    • @luislovo5053
      @luislovo5053 3 หลายเดือนก่อน

      Where?! Can I join I don't think I am making enough as I should

  • @bryanleverett2830
    @bryanleverett2830 4 หลายเดือนก่อน

    Just swap the channel A and channel be wires on the sensor side. Truck stays oem, sensor now works ( with a non-oem wired sensor ). That’s a great catch though. Where the heck in the world are you to see that?

  • @hw4adam173
    @hw4adam173 หลายเดือนก่อน

    I installed the ring gear on the drive unit the other day... it was interesting

  • @panchasnyk8895
    @panchasnyk8895 6 หลายเดือนก่อน +1

    Maestro

  • @estebanhernandez3264
    @estebanhernandez3264 6 หลายเดือนก่อน +1

    Wow thats crazy. Good job comparing to a known good truck.

  • @TheMadJoker87
    @TheMadJoker87 6 หลายเดือนก่อน

    ...i dont get it, those sensors are not supposed to be directional, you should be able to duck tape it in any angle and it should work the same way, there has to be something else going on there

    • @octaviocarrillo5954
      @octaviocarrillo5954 6 หลายเดือนก่อน

      This style of sensor has two sensors in one (phase A and phase B). The computer is watching the sequence of each phase for direction and frequency of each phase for speed. Being that the sensor was 180 deg out, the computer is seeing opposite direction than it’s expecting. If it were a single signal sensor, you’re correct the angle wouldn’t matter.

  • @kslift5334
    @kslift5334 6 หลายเดือนก่อน

    Anyone have toy diesel code 12-4, how often harness issue or always turbo????? Why are these forklifts such crap now. Toyota ran forever in the 7 series days