How to engrave text in rhino

แชร์
ฝัง
  • เผยแพร่เมื่อ 21 พ.ย. 2024

ความคิดเห็น • 20

  • @davcastroruiz
    @davcastroruiz ปีที่แล้ว

    I just started with 3d painting after so many years, I had a mesh surface when I was trying to extrude, thank you for your video, really solved my problem, I am doing pets tags so this is really helpfull to engrave text in it

  • @danielw8302
    @danielw8302 หลายเดือนก่อน

    Thanks Duterque - Been a while since i've done this so the tutorial was a brilliant reminder :)

  • @YogiPamungkas-rz2yt
    @YogiPamungkas-rz2yt หลายเดือนก่อน

    how to make text in the bottom area (on the other side of this video)?

    • @DuterqueStudio
      @DuterqueStudio  หลายเดือนก่อน

      On the edge you mean? Use the flow on surface like on the video

  • @chenafrita1177
    @chenafrita1177 9 หลายเดือนก่อน

    how did you engrave the drawing ? do you have a video about it ?
    thanks

    • @DuterqueStudio
      @DuterqueStudio  9 หลายเดือนก่อน

      Same way, you just need to have your drawing as closed curves, then you extrude it in the same way you extrude your text

  • @martina5328
    @martina5328 7 หลายเดือนก่อน +1

    Since it is Rhino (i.e. no logic and nothing makes sense, and every move is a trick question), I would like to know the properties of the 3D circle that you start with. Doing the exact same thing with a box will not work. So there is something very specific, some very specific properties that the 3D circle has that you have left out. You cannot simply make a 3D box or 3D circle an repeat the procedure. (That would make too much sense)

    • @DuterqueStudio
      @DuterqueStudio  7 หลายเดือนก่อน

      doing the exact same thing with a box will work, you probably missed a step

    • @martina5328
      @martina5328 7 หลายเดือนก่อน

      @@DuterqueStudio No , the text will fall through the surface if put on top of it. Rhino always places the text at the bottom. I wish you could arrange the order as layers, similar to photoshop.
      And projection gives the error message, - projection missed its target or similar. I did manage to project text on a curved surface following a clip on that - by creating a strip from the curved surface matching its length. Then turning that strip i to a surface. Put text on that surface, and project it back on to the curved surface.
      But I cannot create the same strip from an already flat surface with the same command.
      This software is bloated junk.

  • @taeshunho6530
    @taeshunho6530 2 ปีที่แล้ว

    Do you have to change the colour of the text so that it can be laser cut?

    • @DuterqueStudio
      @DuterqueStudio  2 ปีที่แล้ว

      To laser cut you need to export only the curves that you want the laser to cut in .iges or .dxf depending on the software used by the manufacturer.

  • @Lahloso718
    @Lahloso718 ปีที่แล้ว

    How to remove text from 3D file you have downloaded ?

  • @jeillan212
    @jeillan212 ปีที่แล้ว

    thank you

  • @MM-iu8rp
    @MM-iu8rp ปีที่แล้ว

    I think you are a french native speaker ;)

  • @martina5328
    @martina5328 7 หลายเดือนก่อน +1

    Project does not work. Flow along surface does not work. Hey, here is a suggestion - specify what is special about the surface of the medallion that makes all this work !

    • @DuterqueStudio
      @DuterqueStudio  2 หลายเดือนก่อน

      I think you didn’t try hard enough…

    • @martina5328
      @martina5328 2 หลายเดือนก่อน

      @@DuterqueStudio Honestly, the software is a joke. A bloated mess - just like so many other applications.

  • @martina5328
    @martina5328 7 หลายเดือนก่อน +1

    What a joke...