I did all of this without takin out ball joints and everything. Took the tire off and disconnected the suspension. Then used a jack to compress the suspension and slept the block into place. Took about an hr without all the extra the have you do
Good because looking at this video was kinda painful when I was thinking all you would need to do is jack up/compresse the shock and the spacer would fit one shot 😅
I'm betting he already had this disassembled then put back together then filmed the video. Those nasty rusty bolts don't come out that easily the first time.
I’ve owned 4 trucks in about two years. Each one I had installed a leveling kit and every time I watched this video just to make sure I was doing it right. I’m pretty sure I’m getting the hang of it. Thank you so much for an easy to follow install.
Loved the video and the leveling kit. It doesn't fully level it out but God it does look so much better. Only thing is that it doesn't take 2 taps for that upper ball joint to come out lol. But it is a very simple install. Torque specs would have been nice for the video
I have this EXACT leveling kit on my 2017 Silverado. It's just enough to take the ugly factory rake out of play. My only comment is that this "leveling kit" doesn't actually level your truck and it still has about a 1" rake to it. Great value for the money though and a no-brainer to improve the look of your truck.
I didn't do most of that. I loosened the sway bar link all the way, but left it connected. Then I took the top three nuts off with a ratchet and extensions from the top. Then I took the two bolts out of the bottom and it came right out.
Worthy of note: 5:33 the stock strut bolts are 15mm, not 17, at least on my 1500, but the new ones are 17 mm. Also 7:25 my upper control arm was the opposite of what's shown here, you needed to pry up in this video but I had to pry DOWN a good ways, tough mechanics of prying it down and lifting the floppy control arm assembly upward! Jack stands are DEFINITELY your friend to hold the control arm when disconnecting the ball joint and tie rod!
12/22- My leveling kit for the 2018 (1500) came with strut preload spacers along with the lower strut extensions that you installed in this video. Looks like I’ll need to borrow someone’s strut compressor!
please take note of the "get an alignment" comment at the very end. doing this will cause your front to tow in. not a big deal but if you don't get it realigned pretty soon after you can ruin a good set of tires!
How come on your site you only offer these type of spacers with leveling kits, but with front & rear lift kits you only have the round top-strut spacers for the front?
In the video, it states up to 33" tires can be installed with this lift kit. But in the description, it says 32". Any clarification? Thanks for the information, by the way.
Use a tape measure to measure the middle of your front & rear wheel well edges to the ground. On mine, factory, the rear is about 3.25" higher than the front. This will tell you what you need to be completely level. Keep in mind your truck will squat if you put any weight in the rear if it's level.
Could I install a regular suspension lift (6") after this is installed or should I uninstall the leveling kit before I install a lift kit? Only use one or the other not both?
A large prybar under the strut and against the lower control arm will allow you to remove a strut... but not allow enough room for the spacer. You have to pop the upper ball joint.
This type of plastic has a compressive strength comparable to all the other components of the suspension. Also doesn’t corrode so i’ll take the plastic any day.
@@jaredleclerc4434 that’s poly or nylon, he said pure hardened plastic, I agree with you if it’s those 2 things, but think about potentially trusting your life on that plastic. I will choose safety over price.
I measured mine and by those numbers I would need a 3" level but I've been reading anything over 2" puts some suspension components in bad positions and angles but I do not wanna replace or upgrade anything else right now so I ordered the 2".
I know this question is old. But I just got this kit today. And if anyone else is wondering why the bolt needs to be flipped around it is because the bolts will hit your front axles. So they need to be placed from top down with the nut on the bottom.
Bullshit never in my life did I have an upper control arm stick like I did on my 2016 w/30k miles. I bent a full ball joint separator like a banana. Bent the upper then destroyed the joint.
Shop this Rough Country Leveling Kit: amtrucks.at/2QpGsJf
Subscribe for Daily Truck Videos: bit.ly/atcgrsubscribe
I did all of this without takin out ball joints and everything. Took the tire off and disconnected the suspension. Then used a jack to compress the suspension and slept the block into place. Took about an hr without all the extra the have you do
Good because looking at this video was kinda painful when I was thinking all you would need to do is jack up/compresse the shock and the spacer would fit one shot 😅
Yeah it really seemed like these guys on both of their videos went overboard.
You make popping that ball joint out so easy. Mine took a ball joint fork and a lot of friggin beating. 2 hour job turned into about 6
How did you get it out?
Same
Sounds about right
I’m running into that issue right now.
I'm betting he already had this disassembled then put back together then filmed the video. Those nasty rusty bolts don't come out that easily the first time.
Install this today on my 2017 Silverado using this vid as a guide. Took me about 2 hours at the base auto hoby shop. Thank you for the vid!
Thanks a bunch for watching, Adam! Make sure to subscribe if you want to see more! -Zach
I’ve owned 4 trucks in about two years. Each one I had installed a leveling kit and every time I watched this video just to make sure I was doing it right. I’m pretty sure I’m getting the hang of it. Thank you so much for an easy to follow install.
Thanks for watching and I'm glad our videos are helping you out! -Zach
Loved the video and the leveling kit. It doesn't fully level it out but God it does look so much better. Only thing is that it doesn't take 2 taps for that upper ball joint to come out lol. But it is a very simple install. Torque specs would have been nice for the video
Great video! I like the fact that it's a vehicle with some use and not one that's all new and shiny. More what I actually see when doing this myself.
Thanks for watching!! -Zach
Living in he south is so awesome, trucks have to be like 30 years old and sat in someone’s back yard for 5-10 years to get that rusty
Welcome to PA where this happens to new trucks just by sitting in our parking lots! -Zach
I have this EXACT leveling kit on my 2017 Silverado. It's just enough to take the ugly factory rake out of play. My only comment is that this "leveling kit" doesn't actually level your truck and it still has about a 1" rake to it. Great value for the money though and a no-brainer to improve the look of your truck.
Just put more air in the front tires than the back.
@@shanesubashe787 😂😂😂😂
you want some rake if you ever tow anything.
Or put some weight in the bed. Kinda counterproductive if you're wanting to sit higher than stock but it'll take that 1" rake out of the equation
I didn't do most of that. I loosened the sway bar link all the way, but left it connected. Then I took the top three nuts off with a ratchet and extensions from the top. Then I took the two bolts out of the bottom and it came right out.
Worthy of note: 5:33 the stock strut bolts are 15mm, not 17, at least on my 1500, but the new ones are 17 mm. Also 7:25 my upper control arm was the opposite of what's shown here, you needed to pry up in this video but I had to pry DOWN a good ways, tough mechanics of prying it down and lifting the floppy control arm assembly upward! Jack stands are DEFINITELY your friend to hold the control arm when disconnecting the ball joint and tie rod!
12/22- My leveling kit for the 2018 (1500) came with strut preload spacers along with the lower strut extensions that you installed in this video. Looks like I’ll need to borrow someone’s strut compressor!
To be honest he didn't need to undo all of that. Was able to do the CV Axles by just removing the coilover.
please take note of the "get an alignment"
comment at the very end. doing this will cause your front to tow in. not a big deal but if you don't get it realigned pretty soon after you can ruin a good set of tires!
I see this in my near future! Thanks for the video
Thanks for watching! -Zach
PS, I used a 5ft bar to maneuver the blocks and struts to get the bolts in. The large bar enabled me to do the job alone very easily
Damn. That truck is Rusted out to be so new
Man, I always thought 2 inches was great! Its been good for me and it’s okay not having the big ass 6 inches
A 2 inch lift is plenty for most people! Add some all-terrain tires with it and you'll completed change the look of your truck. -Zach
"Thought 2 inches was great" 😂😂😂😂 That's NOT what she said!😅
Love these videos. Fun to watch and very informative.
How come on your site you only offer these type of spacers with leveling kits, but with front & rear lift kits you only have the round top-strut spacers for the front?
I have a question for you. Could it be done just by removing the tire then shock then putting it all back together?
NO torque wrench required? Especially on the ball joints?
🤣
Can anyone tell what size those aftermarket wheels are? They look to be 16’s but I was under the impression 16’s wouldn’t fit, am I mistaken?
What inch level kit would be best for the front and back to be completely level
That angle for that ball joint though… new UCAs necessary?
Not if you like burning through ball joints
In the video, it states up to 33" tires can be installed with this lift kit. But in the description, it says 32". Any clarification? Thanks for the information, by the way.
im fitting 32's rn so gotta fit 33's
Thanks for the video.
Thanks for watching, Shane! Make sure to subscribe if you want to see more! -Zach
I was gonna say just unbolt strut compress strut slip in and slid bolts in maximum 1hr
Very informative video, big thanks pal, but Do you think 2.5 would be 100% leveled with the rear?
Use a tape measure to measure the middle of your front & rear wheel well edges to the ground. On mine, factory, the rear is about 3.25" higher than the front. This will tell you what you need to be completely level. Keep in mind your truck will squat if you put any weight in the rear if it's level.
Ya put the sway link bushing on backwards
How long after the kit should I get an alignment? Would I be good for 100/150 miles?
I would recommend getting one done as soon as possible after installing. -Zach
Are the durable enough. They look cheap.
What are the wheels/tires that you added?
Could I install a regular suspension lift (6") after this is installed or should I uninstall the leveling kit before I install a lift kit? Only use one or the other not both?
We recommend one or the other.
Have u tried it
Looks like the inner c/v shaft joint pop out..
Can I still add this 2’ level on my lifted Silverado which have a 5’ kit on it?
Did you ever try? I have a 6 inch and thinking I'm going to try this up coming week
Do they make it for the 2004 Silverado?
What brand are the wheels and tires
Is this kit safe to install with the stamped steel upper control arms?
What are they made of? Metal or a plastic of some sort? I just ordered mine and it seems like plastic of some sort?
@BAPPOELCHAPO yes I did and corrected myself haha did you even see it above this question haha
Why did you turn bolt downward and not pushing it up like the previous one
so it doesnt hit the axle
Do you need a wheel alignment if you
Install this kit? Thanks
I would highly recommend it after installing a kit like this! -Zach
Why cant you just lift it up and take the shock bolts out instead of taking everything apart?
A large prybar under the strut and against the lower control arm will allow you to remove a strut... but not allow enough room for the spacer. You have to pop the upper ball joint.
Do you have to do a alignment after putting this leveling kit?
Yes you should
You should, but doesn’t mean you have to, if you install and it drives fine and is sitting normal still (angle of tire) , I wouldn’t worry.
I’d be more worried about him saying this is 100% plastic
This type of plastic has a compressive strength comparable to all the other components of the suspension. Also doesn’t corrode so i’ll take the plastic any day.
@@jaredleclerc4434 that’s poly or nylon, he said pure hardened plastic, I agree with you if it’s those 2 things, but think about potentially trusting your life on that plastic. I will choose safety over price.
Is it safe to have the upper leveling frm the top of the strut and the bottom at the same time?
Can you fit 33x12.5x20 ?
Yes you can very easily
does anyone know the wheels in this video?
How high would have to go to get rid of the rake completely ? 2.5 ?
I’m wondering the same thing did you find out?
I measured mine and by those numbers I would need a 3" level but I've been reading anything over 2" puts some suspension components in bad positions and angles but I do not wanna replace or upgrade anything else right now so I ordered the 2".
@@Firechief100 That is my question as well.
Did they buy this truck after katrina flood
Just a Pennsylvania truck, sadly. 😅 Thanks for watching! -Zach
They still run for decades with rust. I’m an IA/MN example.
I’m just trying to find out if I bought this kit, if I need to replace he upper control arms!
Why do the bolts have to go down instead of up like facrory bolts
They can go any way your heart desires, he did them down so he can use his impact on the nut.
I know this question is old. But I just got this kit today. And if anyone else is wondering why the bolt needs to be flipped around it is because the bolts will hit your front axles. So they need to be placed from top down with the nut on the bottom.
Bullshit never in my life did I have an upper control arm stick like I did on my 2016 w/30k miles. I bent a full ball joint separator like a banana. Bent the upper then destroyed the joint.
Dont get this product. Its not really a 2" its a 1". Just installed it on my 08 silverado. And sure enough NOT A FULL 2"
He literally says that in the video
Maybe you gotta let the spring settle and it will "adjust to a 2" lift lol
@@B_HarTz I think he meant the block itself is only 1” but that’s bc the geometry of the suspension will move it 2” for every 1” 😂
Lol I needed a 2.5 i wanted it leveled
Bruhhhhh all u need to do is unbolt the strut and lift it with a jack and bam 😂
Exactly what I was thinking.
Talk about rust...😮😳😦😮😲
Couldn't get the red block? HAHA
Will this work on a 4x4
@a l hahah, I swear people are idiots sometimes . It's like saying "will this work on my Silverado if I have the same one?"
😭😭😭😭
@a l not on a silver one
Just saw it on the video it’s plastic haha
Sorry bro but real mechanics dont use gloves
Okay. 🤷♂️ Thanks for watching! -Zach
This is worse then doing surgery on a human
Does this put any added strain on the drivetrain or anything?
The change is so minor that it doesn't take anything out of angle too much. I have this exact level on my 2017 Silverado and it's the perfect look.
@@Adman-p4j thanks!
@AdmanToronto 2 years later, how many mile have you put on? Any issues with cv joints since?