ไม่สามารถเล่นวิดีโอนี้
ขออภัยในความไม่สะดวก

Crank Bolt Removal on Toyota Sienna. No special tools!

แชร์
ฝัง
  • เผยแพร่เมื่อ 10 ต.ค. 2020
  • Toyota Crankshaft Bolt Removal, 4 different methods tried, with the last one being successful. I did not want to use the starter bump method, because even though you can loosen the bolt, you still have no way to tighten it again to the correct torque!
    (I didn't have a strong impact or an air-driven impact, but this video is aimed at people with somewhat basic tools)
    **If the video was helpful, remember to give it a "thumbs up" and consider subscribing. **
    Disclaimer: Due to factors beyond the control of Pen-Pusher, I cannot guarantee against improper use or unauthorized modifications of this information. This video and all opinions are truthfully my own.
    Pen-Pusher assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk.
    Pen-Pusher recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of Pen-Pusher, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result.
    Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Pen-Pusher.

ความคิดเห็น • 49

  • @jedisentinel1499
    @jedisentinel1499 2 ปีที่แล้ว +2

    I admire your ingenuity! I just replaced a timing cover seal on my 05 Camry. I have a corded harbor freight impact wrench I must have bought for under $40 and their impact sockets, for changing my snow tires. Rattled the bolt right out. Then I have a set of torque sticks I bought from them. I used the 100ft-lbs one to run it back on and called it a day. Saves me time having to charge my compressor for my pneumatic wrench. I’m a former Toyota mechanic by trade so I have Snap-on, Matco, Craftsman tools and I use the cheap tools even more sometimes 😂
    My point being if you’re a DIY’r, harbor freight can be a fantastic resource. It’ll save you SO headache too. 😉

    • @Pen_Pusher
      @Pen_Pusher  2 ปีที่แล้ว +1

      Thanks for the tips! :)

    • @chrispaul1310
      @chrispaul1310 2 ปีที่แล้ว

      111

    • @robertbigler7743
      @robertbigler7743 2 ปีที่แล้ว +1

      Hi Jedi... I tried a Harbor Freight electric impact and a HF air impact. Neither worked. Then I bought HF's "Earthquake" air impact (around 600 ft/lbs)... It zipped the bolt off like it was finger tight!

    • @jedisentinel1499
      @jedisentinel1499 2 ปีที่แล้ว

      @@robertbigler7743 great! Just don’t use it to put it back on. Tighten gently and to the exact torque spec🙃

  • @daveshanton485
    @daveshanton485 2 ปีที่แล้ว +1

    Thank you for the demonstration! I really like how you propped up the end of the breaker bar on a jack!

    • @Pen_Pusher
      @Pen_Pusher  2 ปีที่แล้ว

      Hi Dave, it helps to keep your socket and extension level with the bolt. And it is so easy to get to the right height!

  • @sarahsmith4617
    @sarahsmith4617 ปีที่แล้ว

    Great video, thanks for sharing. It's nice to see other peoples trial and errors as well lol. And you have a wonderful voice!

    • @Pen_Pusher
      @Pen_Pusher  ปีที่แล้ว

      Thanks Sarah. Sometimes it is just a matter of perseverance! :)

  • @juanrivas5250
    @juanrivas5250 3 ปีที่แล้ว +2

    Muy buen video felicidades por tu excelente aporte saludos! Desde México 🇲🇽

  • @jetdr
    @jetdr หลายเดือนก่อน

    In America, we call that a cheater bar, technical term would be a Torque Multiplier!! Have to do what needs done sometimes..

    • @Pen_Pusher
      @Pen_Pusher  หลายเดือนก่อน

      Haha Git er done!

  • @PeterHernandez-lg2eh
    @PeterHernandez-lg2eh หลายเดือนก่อน

    I'm in the same boat. 20p4 Toyota sienna timing belt replacement.

    • @Pen_Pusher
      @Pen_Pusher  หลายเดือนก่อน

      Good luck! I have two videos on that. One features the timing belt & water pump. The other features the cam seals. :)

  • @JockeyCake
    @JockeyCake 2 ปีที่แล้ว +1

    Well done mate

    • @Pen_Pusher
      @Pen_Pusher  2 ปีที่แล้ว

      No worries mate. :)

  • @raffuy9745
    @raffuy9745 ปีที่แล้ว +1

    Use a braker bar and crank up the starter easy peasy.

    • @Pen_Pusher
      @Pen_Pusher  ปีที่แล้ว

      Sure, but how do you torque it at the end?

  • @hlkushwaha1287
    @hlkushwaha1287 5 หลายเดือนก่อน

    Good

  • @dannysautorepair
    @dannysautorepair ปีที่แล้ว

    Great video thanks

    • @Pen_Pusher
      @Pen_Pusher  ปีที่แล้ว

      Thanks for the support Danny! :)

  • @MrAcc45
    @MrAcc45 3 ปีที่แล้ว +1

    So the chain has more grip on the pulley than the belt....

    • @Pen_Pusher
      @Pen_Pusher  3 ปีที่แล้ว +3

      Yes, much more. When I did the cam sprockets I decided to put a piece of old belt between the chain and the metal. It worked perfectly!

  • @roltyd22
    @roltyd22 2 ปีที่แล้ว

    Did you use the vise grips when you reinstalled it?

  • @samcruz9027
    @samcruz9027 7 หลายเดือนก่อน

    What direction to take off? Counter clockwise?

    • @Pen_Pusher
      @Pen_Pusher  7 หลายเดือนก่อน

      Yes!

  • @stephenyoungblood3683
    @stephenyoungblood3683 2 ปีที่แล้ว +1

    How long was your cheater bar?!?

    • @Pen_Pusher
      @Pen_Pusher  2 ปีที่แล้ว +4

      I used a 24 inch breaker bar, with a wider 36 inch pipe slipped over it. :)

  • @joshuacormett7237
    @joshuacormett7237 ปีที่แล้ว

    Did you have to replace the harmonic balancer??

    • @Pen_Pusher
      @Pen_Pusher  ปีที่แล้ว

      No, still using the same one. :)

  • @optimalorlando
    @optimalorlando 7 วันที่ผ่านมา

    They make a tool to remove it

    • @Pen_Pusher
      @Pen_Pusher  7 วันที่ผ่านมา

      Yes, and it is easier if you have the tool!

  • @LK-dm7kx
    @LK-dm7kx 3 ปีที่แล้ว +1

    You damaged the ribs of the pulley with that chain.

    • @Pen_Pusher
      @Pen_Pusher  3 ปีที่แล้ว +5

      The ribs are pretty sturdy. I have done this on two vehicles. No marks on one and two small marks to clean up on the other. I protected the crank pulleys with pieces of old drive belts. It worked perfectly!

  • @charlestailor8218
    @charlestailor8218 2 ปีที่แล้ว

    That's a special tool. Description listed "no special tool"

    • @Pen_Pusher
      @Pen_Pusher  2 ปีที่แล้ว

      Not considered special in any shop. :)

  • @cndvd
    @cndvd 10 หลายเดือนก่อน

    Just buy a battery 1/2 impact , or borrow. Everybody got one.

    • @Pen_Pusher
      @Pen_Pusher  10 หลายเดือนก่อน

      You may be lucky, but many 1/2 inch impacts are not able to loosen that crank bolt. Crank bolts and axle nuts can be vey stubborn!

    • @cndvd
      @cndvd 10 หลายเดือนก่อน

      @@Pen_Pusher Get a good powerful gun. Maybe need an air one. I’ve cranked the starter before on a 4cyl using a breaker bar. That works but seems a bit “scary” lol.

    • @Pen_Pusher
      @Pen_Pusher  10 หลายเดือนก่อน

      @@cndvd Yes, a good air gun will do the job. The problem with using a breaker bar to loosen it is that you still need something to help when you want to tighten it again!

    • @cndvd
      @cndvd 10 หลายเดือนก่อน +1

      @@Pen_Pusher Yes that’s right got to torque it. I’ve jammed a large screwdriver in there to loosen and tighten it, but need to be able to insert it in and lock in in there. The wheel bearing I’ve use a very long pipe over a breaker bar, always broke loose. My Ridgid impact so far worked, but the newer ones are even stronger for the crank bolt. Still surprised it worked.

  • @yakuachbach6083
    @yakuachbach6083 3 ปีที่แล้ว

    you could've just cranked the motor with socket and cheater bar on it,Lol

    • @Pen_Pusher
      @Pen_Pusher  3 ปีที่แล้ว +1

      True, but then how do you fasten it again? Start in reverse?

    • @roltyd22
      @roltyd22 2 ปีที่แล้ว

      @@Pen_Pusher So did you use the vise grips when you re installed it?

    • @Pen_Pusher
      @Pen_Pusher  2 ปีที่แล้ว +3

      @@roltyd22 Yes, that is the advantage of using this method. It works for both taking it off and tightening it again to the proper torque. :)

    • @DaveEppel
      @DaveEppel ปีที่แล้ว +1

      You haven't broken teeth of a flywheel yet by doing the above. Lucky man.

  • @davidwest9817
    @davidwest9817 2 ปีที่แล้ว

    Stop