Replacing The Rear Window Brake Light 2006-2010 Hyundai Sonata

แชร์
ฝัง
  • เผยแพร่เมื่อ 7 ก.พ. 2025
  • Here are some of the tools that jimthecarguy uses
    www.amazon.com...
    In this video I will show you how a simple light bulb job turns into a pain in the rear end because of the so called engineer who designed this car.
    Due to factors beyond the control of jimthecarguy, it cannot guarantee against unauthorized modifications of this information,. jimthecarguy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. jimthecarguy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, chemicals, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of jimthecarguy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not jimthecarguy.

ความคิดเห็น • 202

  • @canyondanhandyman2989
    @canyondanhandyman2989 3 ปีที่แล้ว +14

    Hi Jim! I wanted to take the time to thank you for taking the time to make and post this video. I've put over 100,000 miles on this 07 Sonata, and today is the first time I've had a working center brake light on this car!! That's thanks to you! I have spent whole days in the past trying to replace the bulb through the little square hole in the trunk. I also tried gently prying the light housing from the back seat too...no go. I know there are two bulbs rattling around up in there from past tries. There was some bleeding, and quite a bit of swearing involved with those tries. I came VERY close to pulling out the dye grinder and cutting an access hole right where the Hyundai engineers should have put it! I still have trouble imagining how they could have done worse on this design. It's obvious that it was not designed at all really, just an "after-thought" that makes what should be a very simple job replacing a bulb a nightmare!! I own the car so I had no problem cutting off the stupid 1" long fin on the light socket, and two of the tabs on the light housing that make it even more difficult to remove and re-install the housing on the rear window deck. So, thanks againJim for helping me make my car a little safer!!!!!

  • @ferret2267
    @ferret2267 ปีที่แล้ว +3

    Thanks so much. You saved me a bunch of time and frustration!! For anyone wondering. It is a 921 bulb.

  • @jimchandler6744
    @jimchandler6744 ปีที่แล้ว +2

    Hey, Jim: I just discovered something that might help some others with that stupid third light. After several hours of in and out of the trunk and trying to find those damned screws and then trying to get it back in after installing the new LED bulb, I was ready to re-install the thing and had all sorts of problems getting it back in.
    Three times I had to take the bottom plate off the light housing to retrieve the bulb after it fell off in there. Finally I put it in and added a couple of drops of super glue to the base. No more falling out.
    The next problem was getting the thing back in place. I finally said "Enough!" and grabbed my diagonal cutters and cut that long tail off of the socket. I cut it just short of the round piece. The extra plastic served no purpose as far as I could see so off it came. I put the socket in the housing and the whole mess slid right into place with a little coaxing. Put the two screws back in and done.
    Take a look at that long tail next time you have to do one. Cutting it off makes things a LOT easier. I have to agree with you on the utter stupidity of this thing.

    • @eightiesgod
      @eightiesgod 11 หลายเดือนก่อน

      This is the way to go... Was very simple doing this. I too wondered what was under that tape wrap and this is the DEVINE answer. They just over modified this piece but for no good reason but to fleece you at the stealership and whatnot. Thank you for simplifying this tedious mess.😀

  • @kennya3861
    @kennya3861 4 ปีที่แล้ว +14

    This is why you got to love TH-cam and guys like Jim The Car Guy! Thanks Jim, a BIG help!

  • @greenboy1916
    @greenboy1916 3 ปีที่แล้ว +4

    I took my car to get inspected and the mechanic didn’t know how to take the back light off and that was the only thing holding me back from a clean inspection. Thanks to your video I was able to do in 45 minutes well I’m sure a dealership would’ve taken a day or two to do. Thank you very much I really appreciate the help you’ve provided today have a great day and God bless.

  • @kmath50
    @kmath50 4 ปีที่แล้ว +6

    I followed another procedure where part of the socket is cut off while it is out. This allows the lamp to be re-installed into the housing, with plenty of clearance to put the housing back in.
    That is what I did on mine. Worked well.

    • @kmath50
      @kmath50 7 หลายเดือนก่อน

      I did the same. Made it easier to re-install the lamp into the housing.

  • @RyanCollinsFlyinRyan8
    @RyanCollinsFlyinRyan8 4 วันที่ผ่านมา

    I watched your video before working on my godson's '08 Sonata. Your video was extremely helpful. The only mishap I experienced was the bulb socket dropped down and the bad bulb fell out of the socket. I retrieved both with little effort and got everything buttoned up without further issues. It probably took me 25 mins. after it was all said and done. Thanks!

    • @jimthecarguy
      @jimthecarguy  2 วันที่ผ่านมา +1

      Glad the video was helpful and you got it fixed!

  • @ez2hotwire
    @ez2hotwire ปีที่แล้ว +1

    My man!! The dealership said they’d replace it for $140!!! Thanks to you and this video, I just replaced it, took me 1/2 hour (gotta get around some stereo equipment). Thank you for the perfect instructions!!

    • @brettrossi034
      @brettrossi034 ปีที่แล้ว +1

      LMAO 140$? Isn't that quite a joke that the dealers would charge that for something that should be quick for people who know the cars. Absolutely wild! But at least you took the time to learn and do it yourself save money. I was doing the same as you 👍

    • @SL-pg4dh
      @SL-pg4dh ปีที่แล้ว

      Stealership.

    • @asianstud7
      @asianstud7 ปีที่แล้ว

      LOL. what fucking crooks.

  • @captpat6421
    @captpat6421 5 ปีที่แล้ว +20

    I clipped the long plastic stem off of the light bulb socket so that it can be inserted into the fixture and then the whole fixture snapped into place as a unit. Also, you can see the screw behind the felt at a steep angle through the rectangular hole on the left side. It really helps when putting it back together.

    • @keithcunningham2254
      @keithcunningham2254 3 ปีที่แล้ว +3

      Before reading your comment, I realized the 3/4" tang on the underside of the light bulb socket was the issue making the replacement of the bulb SO difficult.
      I used diagonal pliers to cut that long plastic tail from the bottom of the bulb socket and the whole thing assembled easily from above the rear shelf and (with some gentle urging) slid into place on the shelf.
      I also attached an 18" piece of string to the wire connector coming off the bulb socket to help fish the connector into the laterally displaced opening inside the trunk, where it connects to the matching (powered) connector.
      My thoughts: 1) Long tang on bottom of bulb socket "would" be useful if the bulb socket base could be accessed from WITHIN the trunk.
      2) Hyundai seems to have used a bulb socket from another application (location) which makes its use for the 3rd brakelight extremely difficult to replace.
      And 3) All that WOULD have been needed was for Hyundai to place an adequately-sized access opening directly below the bulb socket. In that case, the long tab would have been very useful in quickly and easily changing a blown 3rd brakelight bulb.
      Anyway - after

  • @lilypurcella1491
    @lilypurcella1491 3 หลายเดือนก่อน

    I can not tell you how much I appreciate this video! The first one I saw told me to take apart my whole back panel. Although difficult, this was so much easier! Thank you!!

  • @acidhairball9625
    @acidhairball9625 3 ปีที่แล้ว +1

    Thank you. This was the only video which showed how to replace the bulb without having to take apart the backseat.

  • @carlosotero934
    @carlosotero934 5 ปีที่แล้ว +5

    Lol I was one of the ppl you were talking about in the beginning of your vid. I went in myself at first thinking no biggie and then was like wtf . Thank for your information and knowledge.

  • @TerranceCulianos
    @TerranceCulianos ปีที่แล้ว

    I failed the NYS inspection due to this. Mechanic said 80 dollars since it’s a pain to replace and would take them roughly 2 hours. With this video, took me 10 minutes and $6. You are great!

    • @asianstud7
      @asianstud7 ปีที่แล้ว

      what bulb model number you had to purchase? thanks

  • @dancollinsandapiano
    @dancollinsandapiano 3 ปีที่แล้ว +1

    Thanks for this. Worked great but was like a game of Operation trying to line the socket with the enclosure on reinstall.

  • @AMC-eq3jr
    @AMC-eq3jr 8 หลายเดือนก่อน

    Did not pass NYS inspection - unfortunately I am pass the 30 days because I was out of state. Just need to pay an extra 37 for another inspection formality. This was weighing on my mind while I was away until you walked me through. Job was completed in 30 hard minutes. Thank you so much, sir.

  • @williamstevens4824
    @williamstevens4824 6 ปีที่แล้ว +9

    Wow ! Yes those Engineers really are brilliant ! They never think about the guy that has to replace the bulb for sure. I came up with a few new cuss words myself changing mine abut 2 years ago on a 2009. I wish I saw this video then. Great job. Have a Happy New Year. I enjoy your videos. Keep them coming. Thanks Jim. Bill😊

  • @Kop05.55
    @Kop05.55 11 หลายเดือนก่อน

    Thank you for this life saving video Jim. I sweared so much at first at Hyundai then after a week calmed down. The job was a nightmare and I was about to throw the towel in until I checked your video out. Wow, Hyundai are a real pain in the butt. My back still aches from changing a single light bulb. Jim, thanks again, great job.

  • @antonjames8405
    @antonjames8405 4 ปีที่แล้ว

    I was the guy at 0.40...thought I would fix it without reading any books or youtube and dived right in ...then WTF .....thanks for sharing your vid, advice and guidance ....appreciation from Canada

  • @Virtue_bound
    @Virtue_bound ปีที่แล้ว

    Hi. I just wanted to say thank you for making this guide. I just replaced mine on a 2006 model. Most difficult part was the screws. After removing those, I just used my fingers to dislodge the bulb after prying the assembly out. After replacing, i just forced the contraption with the bulb in. Ezpz lemon cars.

  • @macrossa02
    @macrossa02 5 ปีที่แล้ว +6

    Thanks I will try to replace the light bulb in my 2007 Sonata. I found this the really best way to replace it. Thank you 👍

    • @jimthecarguy
      @jimthecarguy  5 ปีที่แล้ว +2

      Just remember not to touch the glass part of the bulb. Thanks for watching

  • @Loathello
    @Loathello 5 ปีที่แล้ว +2

    THANKS! I just got finished watching another video where they wanted me to take out the rear seat side cushions, the back ledge(?) cover, and some other crap just to get to the bulb. Your way is MUCH better. Appreciate it.
    Oh and 2:10 "I'm too old for this stuff". You and me both, sir. :)

  • @purduephotog
    @purduephotog 4 ปีที่แล้ว +5

    Thank you for taking the time to stabilize it- very watchable ! And just what I needed today too!

  • @CarsExposed
    @CarsExposed 6 ปีที่แล้ว +3

    I had a 1999 Sonata and still one my favourite vehicle drive wise but What a pain in the back side this brake light bulb to replace 😁 thanks Jim 👍

  • @ttbalog
    @ttbalog 3 ปีที่แล้ว +2

    Thanks for this. My lamp holder was already partially dislodged, so I was able to change the bulb from inside the trunk without removing the reflector case from inside the cabin.

  • @BrittCHelmsSr
    @BrittCHelmsSr 2 ปีที่แล้ว

    I just changed the one in my son's 2008 Hyundai Sonata out for the second time. This time I put in an LED bulb that gives three quick flashes when the break pedal is pressed and then goes solid. What a PITA to change! If I ever have to change it out again, I'm bringing out the 2" metal hole saw and drilling a nice big hole in the metal plate below the bulb location.
    At 59 years old and almost 300 pounds, I could have sold tickets to those who would have never believed that I could have gotten into and out of that trunk.

    • @ryan_hm8193
      @ryan_hm8193 ปีที่แล้ว

      hey do you have the name or link of the bulb that you bought that flashes?

  • @toroon
    @toroon 6 ปีที่แล้ว +1

    My wife told me her Elantra has a burnt out third light. Lucky me.
    Thanx for the heads up. Great Vid!!

  • @AW-fb9hk
    @AW-fb9hk 5 ปีที่แล้ว +3

    Thank you SO MUCH! I got my car inspected today and that break light was out. The auto repair store told me it could take them about 2 hours and charge me $60. I was like .. no. So I googled you and I fixed it all by myself ! But yes. I agree. They were not the smartest engineers thinking about this lol

    • @ShisuiHack
      @ShisuiHack 5 ปีที่แล้ว

      That lightbulb cost 60 to buy. 🤦 I just forget about it because I got taillight/brake lights.

  • @gt93grad
    @gt93grad 11 หลายเดือนก่อน

    Painful, but I'm going to give it a try. Thanks Jim! I never would have found those screws.

  • @ninastacey
    @ninastacey 3 ปีที่แล้ว +1

    thank you so much for the video!! if there’s one thing i’ve learned from taking apart and reassembling parts of my hyundai is that there’s a LOT of dicking around involved in order to get things loose. i’ll never understand why they made this car so difficult to disassemble 🤷‍♀️

  • @heydadchannel
    @heydadchannel 2 ปีที่แล้ว

    Very helpful. I had to stop in the middle today, re-watch, and go find pliers to finish.

  • @tammycoleman4834
    @tammycoleman4834 ปีที่แล้ว

    Unbelievable!!! That is ridiculous!!! 😡 I have to fix mine. 😕😢. Thank you for showing us how difficult this is 😂!

  • @htuesta9131
    @htuesta9131 ปีที่แล้ว

    ¡ Muchas gracias Jim !

  • @fila6243
    @fila6243 5 ปีที่แล้ว +5

    Or you could just cut an access hole in that parcel shelf from in the trunk. No screws. No messing around inside. Reach up and unplug.

  • @jackrabbit2765
    @jackrabbit2765 3 ปีที่แล้ว +1

    Jim I own a 09 sonata, I drilled right thought the metal inside the trunk, right in between, where you unscrewed the two screws, for eazy replacement, about a 3 an half inch size hole..

  • @neogenesisfool
    @neogenesisfool 2 ปีที่แล้ว

    Thank you for making this video. I was able to replace me bulb but I'm never buying a Hyundai again.

  • @joehyundaitech7961
    @joehyundaitech7961 5 ปีที่แล้ว +2

    jim I am a hyundai tech and at the dealership i had a 2010 just now and there is a trick long needle nose pliers to turn counter clock wise from the top and let the bulb drop out from the bottom then the plastic has to be cut to put it back in this is the beast way I know how to describe this its a real pain in the but. there are 2 screws and they are a pain to see from under the trunk its had for me to fit at my size . so u need a lite and a long phillip driver

  • @andrewdutton3831
    @andrewdutton3831 2 ปีที่แล้ว +2

    Holy crap! Just finished this job (sort of) and it was so frustrating overcoming the poor design of this system. (1) the location of the two mounting screws is hard enough, but Hyundai's access to them makes no sense. The left side (as the car drives) access screw isn't too bad. The right side is covered with insulation (the adhesive foam) whose only purpose is to block access to the screw. Then, as if that's not bad enough, the port (hole) in the sheet metal to access that screw is not quite lined up right...the screwdriver has to pivot a little on a slant. The only way to overcome this is to crouch on your back and position yourself inside the trunk at angles that your spine can't handle for long. You have to SEE the screw through the hole in order to access it. No way I was ever going to get it by touch and feel. (2) The gray carpeted panel below the rear window (inside the cabin) is a total cluster*&^% of a design. You see where his right thumb is resting at 07:56 in the video. If that stupid bump wasn't there, you'd have plenty of room to lift up the light assembly to twist left - pull out, or twist right, push in the light bulb. Instead, you have to do what he does and try to finesse the bulb holder into the hole of the light assembly....with hardly any wiggle room. And you HAVE to use needle nose pliers....it aint' happening with your fingers. I tried about 10 times to twist my new bulb in ...no luck. FIVE times, the damn bulb fell inside the assembly itself, and I had to take THAT apart. Finally...I said f*&^ it...it's an older car, and I cut out a 1 inch by 1 inch square hole where his thumb is at 07:56. After doing that, there's plenty of room to pull out the assembly far enough to twist in the bulb, and then put the lighting assembly back into it's place on the rear felt panel. All Hyundai needed to do here was put a plastic access snap panel where I did my cutout. I guess I'll get some grey velcro and cover it up with some custom decorative design.
    He must have had trouble, too, with the re-insertion of the bulb. At 08:19, you can see a cut in the video where I imagine a LOT of time passed for his as well. Looks like the daylight outside has almost turned to night! 😆
    Nice job on this video, sir. You really helped me appreciate the complexity of this system!

  • @AMC-eq3jr
    @AMC-eq3jr 8 หลายเดือนก่อน

    Thanks!

    • @jimthecarguy
      @jimthecarguy  8 หลายเดือนก่อน

      I’m happy to help. Thank you for the $

  • @matthewmccloskysr4260
    @matthewmccloskysr4260 2 ปีที่แล้ว

    Thank you Sir Jim for the informative video. I was able to change the bulb in 15 minutes. Easy peazy with a little patience. Thank you again!

  • @CarsandEspresso
    @CarsandEspresso ปีที่แล้ว

    Thanks for taking the time to show us this!

  • @laurafisher7844
    @laurafisher7844 2 ปีที่แล้ว +1

    Yes, this is similar to the headache of replacing the low-beam/high-beam headlight bulbs on a Sonata.

  • @spdrn011
    @spdrn011 4 ปีที่แล้ว

    Brilliant! And I love your comments!! I've seen people taking half the car apart in other videos to replace it!!

    • @jimthecarguy
      @jimthecarguy  4 ปีที่แล้ว

      Glad it was helpful!

    • @spdrn011
      @spdrn011 4 ปีที่แล้ว

      @@jimthecarguy The shop called me..... yah, it's at least an hour of labor..... $120.00 for a lightbulb! I'm look, no, Hell no! Directed them to your video, got it done for the original estimate, 24.95!!! You rock Jimmy!!

  • @patriciagorman4706
    @patriciagorman4706 5 ปีที่แล้ว +8

    OMG! Thank you for the video. I’m just going to pay someone to do it. 😤

  • @l-trainzero1451
    @l-trainzero1451 3 ปีที่แล้ว +1

    I agree they only think about the assembly not the maintainability. Awesome job

  • @ricknoelle4507
    @ricknoelle4507 2 ปีที่แล้ว

    Thank you very much, Jim. It was very helpful and I appreciate your cheerful personality.

  • @motorbreath7174
    @motorbreath7174 5 ปีที่แล้ว

    Hey folks great video. Let me tell u A GOOD TIP.
    Removal is pretty much how u showed it, long needle nose.
    Installation much easier cut the bottom of the plastic bulb socket off up to where the wires go into it.Gives about an inch more clearance . Your just cutting off a thin tab that was designed to aid removal and installation with your fingertips HAD THE HOLE BEEN CUT IN THE PROPER PLACE IN THE TRUNK. You still have to finesse the housing in a bit but it works. If it was my car I would just take a hole saw underneath it .But, It would never be my car.

  • @Biosynthnut
    @Biosynthnut 5 ปีที่แล้ว +1

    Just had to do this.. I wound up cutting the long part of the socket down to the wires. Turn it into the lens, and you can squeeze the whole thing back into the spot.
    Only thing I couldn't get back in was the screws..
    But the light works.

  • @wademosher
    @wademosher 3 ปีที่แล้ว +1

    Bonus points for not saying 'FUCK'.

  • @krupamic
    @krupamic ปีที่แล้ว

    I think I will give this a try. However, once the bulb socket is removed, I am going to cut the wires and extend them so it is easier to maneuver. I'll also cut that silly tab off too.

  • @amandalittle9397
    @amandalittle9397 3 ปีที่แล้ว

    Thank you so much! Wanted to share my gratitude because I was able to fix this myself with your help!

  • @fjb666
    @fjb666 3 ปีที่แล้ว

    Thank you for making this video. F the engineer who designed that. A couple extra plastic clips on the cover and they wouldn't need the screws, a few more inches of wire and you could pull the whole housing out to twist the bulb.

  • @mikemuday
    @mikemuday 6 ปีที่แล้ว +4

    Wow, this was an incredible help. Thanks for the easy to follow video.

    • @jimthecarguy
      @jimthecarguy  6 ปีที่แล้ว +1

      Thank you for watching . I'm happy to help. Don't forget to subscribe.

  • @stevehilliard1495
    @stevehilliard1495 6 ปีที่แล้ว +1

    You are so professional, not a single cuss word!!

    • @jimthecarguy
      @jimthecarguy  6 ปีที่แล้ว +2

      Hahaha "not a single cuss word" Thank you for editing. Lol Happy New Year.

  • @davidmyers1142
    @davidmyers1142 4 ปีที่แล้ว +2

    I did, in fact, look in to my trunk and say “howdaheck doya even gettadis friggin light bulb?!”

  • @paradaj3
    @paradaj3 10 หลายเดือนก่อน

    Yes this is stupid how much ypu have to go though to change a single light bulb! Thank you for this video!!!!

  • @josephmatos9348
    @josephmatos9348 3 ปีที่แล้ว +1

    I cannot even tell you how frustrating that was! I dropped both bulbs down the freakin thing and will have to take the whole thing apart to get the bulbs and replace the light. Stupid fuckin engineers! How the fuck did u think we can get that! Took me 2hrs and still couldn't do it! A fucking bulb!

  • @scrapmetal100
    @scrapmetal100 6 ปีที่แล้ว +4

    Is a LED available as a replacement?

  • @kimberlymorse1616
    @kimberlymorse1616 4 ปีที่แล้ว +5

    It took 2 people, a lot of cursing, and an hour to accomplish this. It's by far my ONLY disappointment in Hyundai to date - and I have had my car for 12 years with no complaints. She is a beast, and has 200K+ miles on her - but this was total nonsense....what the heck were those engineers thinking!

  • @NathanStrykerYT
    @NathanStrykerYT 5 ปีที่แล้ว +3

    Best fix is 5% tint. Had my car for 8 years, didn't know it had a third brake light until tonight

    • @jimthecarguy
      @jimthecarguy  5 ปีที่แล้ว

      Thanks for watching.I'm happy to help

    • @edgarcastillo219
      @edgarcastillo219 4 ปีที่แล้ว

      Same I have a dark tint and didn't realize that I had a third break light for like 7 years🤣

  • @petemoss9693
    @petemoss9693 6 ปีที่แล้ว +3

    Hi Jim - - - could you of cut the two wires then splice and solder two longer wires together to make much easier to dismantle and pit it all back together - if it was all possible - just a thought - because my son has a Hyundai Sonata and if ever had to do this job like you just did I will personally do what my plan is - thanks for the video . Happy New Year to You and all Your Family

    • @jimthecarguy
      @jimthecarguy  6 ปีที่แล้ว

      Good question.Yes you could but it is really not that bad once you know how. Thanks for watching. Happy New Year.

    • @keithcunningham2254
      @keithcunningham2254 3 ปีที่แล้ว

      Absolutely no need to cut & resplice. Wouldn't make it any easier. The longer (driver side) screw holds the powered connector half into the bottom of the shelf and you can disconnect the bulb socket wire tail from here and completely remove the bulb socket and wire tail from the top side (car interior) of the rear shelf. 18" of string tied onto this wire tail can be fished from above the shelf into the laterally displaced opening inside the trunk where you push together the 2 halves of the existing connector.

  • @zzandal
    @zzandal ปีที่แล้ว

    How do I know what bulb to buy for my 2009 Hyundai rear window brake light?

  • @letsbeout123
    @letsbeout123 2 ปีที่แล้ว

    Thanks soooo much for making this video, it saved me a ton of time and frustration!

  • @PATRICIACornett-x2s
    @PATRICIACornett-x2s 4 หลายเดือนก่อน

    It's a lot easier to do than you were showing. All you have to do is take a long pair of pliers go in the trunk put them up in there and grab a hold of the plastic part of the light and turn it pull it down through the hole change the bulb and put it back.

  • @michaeldelrossi4487
    @michaeldelrossi4487 5 ปีที่แล้ว +1

    If you fold down the back seats you can access the trunk deck screws a little easier to change that bulb, just a thought for next time!

    • @jimthecarguy
      @jimthecarguy  5 ปีที่แล้ว

      I'm happy to help. Watch for the next free tool giveaway coming soon.

  • @jessaRmoney
    @jessaRmoney ปีที่แล้ว

    Thank you! It took me less than 10 min, 👏

  • @theaaronakin
    @theaaronakin 2 ปีที่แล้ว

    This helped thanks

  • @Farehaven
    @Farehaven 3 ปีที่แล้ว +1

    In other videos they are taking side panels off.

  • @mikemcelveen2973
    @mikemcelveen2973 4 ปีที่แล้ว +1

    You held your cool,I know you wanted to break every peice of window glass in that car! Lol. Flat rate in my shop is .2 "small bulb labor" gotta love it. The first time I did one years ago I removed the whole rear deck and seats lol. Thanks for the tip!

  • @Mrcaffinebean
    @Mrcaffinebean 4 ปีที่แล้ว +2

    I have done a lot of work on this car. I have replaced wheel bearings, brake calipers, alternators, gaskets of all kind and I have even done some electrical.
    All the while I thought this car is fairly well designed. Nothing is inordinately difficult to do. Then I changed the third brake light. I have no idea what rookie engineer was in charge of that design because everything is just a fraction of an inch off. Just a few millimeters off the bottom of that light would make it much easier to take out.
    Anyways it done and your video was helpful without it I probably would have ripped it out of the car lol.

  • @SteveRobReviews
    @SteveRobReviews 6 ปีที่แล้ว +1

    You do seem to enjoy doing this for a living eh Jim :) Happy New Year bud and hope you and the family have a great 2019

    • @jimthecarguy
      @jimthecarguy  6 ปีที่แล้ว +2

      Thank you Steve. Happy New Year to you also. I hope all is well.

  • @AG-vq9dy
    @AG-vq9dy 3 ปีที่แล้ว

    Definitely a big help. Thanks for doing this video.

  • @gatorgotme
    @gatorgotme 6 ปีที่แล้ว

    A 25 year old man such as yourself is hardly too old for this! Happy New Year Jim!

    • @jimthecarguy
      @jimthecarguy  6 ปีที่แล้ว

      gatorgotme Thank you for watching and your input. 25 years old , boy do I wish. Happy new year

  • @TheDisgruntledMechanic
    @TheDisgruntledMechanic 6 ปีที่แล้ว +1

    So simple to change! Not. I like saving time! Happy new year Jim.

    • @jimthecarguy
      @jimthecarguy  6 ปีที่แล้ว

      Thank you Mike . Happy New Year.

  • @vidang4258
    @vidang4258 2 ปีที่แล้ว

    Thank you so much for a great video.

  • @BeaverDunker
    @BeaverDunker ปีที่แล้ว

    Does anyone know the bulb part number? I am thinking LED because I am only doing this once

  • @alsmith5714
    @alsmith5714 5 ปีที่แล้ว

    Could you have used long nose pliars to reach up and twist the socket and drop it to install new bulb.?

  • @mikeyrilloraza2493
    @mikeyrilloraza2493 5 ปีที่แล้ว +20

    hyundai made a mistake with that design, they shld have made it maintenance friendly

    • @eastoncolten6666
      @eastoncolten6666 3 ปีที่แล้ว

      i realize Im quite randomly asking but do anyone know of a good site to watch newly released series online ?

    • @grantjesus9703
      @grantjesus9703 3 ปีที่แล้ว

      @Easton Colten Try Flixzone. Just search on google for it :)

    • @brettrossi034
      @brettrossi034 ปีที่แล้ว +1

      I remember changing the headlight assembly too on my Sonata too as well as one time with the bulb change too, huge pain in my you know what to conquer those seemingly simple jobs.

    • @lorimarcus4572
      @lorimarcus4572 ปีที่แล้ว

      L l9l9

  • @blah064
    @blah064 2 ปีที่แล้ว

    Thanks very much. When an expert calls this design stupid and a pain in the rear, it’s as though Hyundai went out of their way to make this difficult. I have an 09 Sonata and it burns out bulbs more than any car I ever had. However, it has 203k miles and runs great. My 2016 Sonata is crap. 35k miles and the white paint is chipping and Hyundai won’t do anything about it. Simple solution, will NEVER buy a Hyundai or Kia ever again. Screw them!!

  • @jimchandler6744
    @jimchandler6744 ปีที่แล้ว

    I just want to know what little Korean rectal orifice designed this mess? My 2010 Sonata has the same problem and the Haynes manual was less than useful. Now that I've seen your video and another I think I can do it. I'm 80 years and too old to be doing this stuff. :-)

  • @Mr.B-Apiary
    @Mr.B-Apiary 2 ปีที่แล้ว

    Thank you never would of figure it out. Use to work on computers and yes engineering was just as frustrating lol. Should be mandatory that they go into the field and have to dismantle what they designed.

  • @alsmith5714
    @alsmith5714 5 ปีที่แล้ว

    Could the shelf be removed for access?

  • @lsquadcreations3175
    @lsquadcreations3175 4 ปีที่แล้ว

    Thank you. I was like how do i put a bulb in . It's crazy how they designed it.🤦‍♀️🤦‍♀️🤦‍♀️

  • @FatNebraskaMom
    @FatNebraskaMom 4 ปีที่แล้ว +1

    Every. Single. Hyundai. Video...a mechanic talking shit about hyundai engineers lol....making me rethink buying another hyundai

    • @jimthecarguy
      @jimthecarguy  4 ปีที่แล้ว

      To be very honest I do like the Hyundai products. I just bought the Santa Fe myself. Thanks for watching.

  • @X5claus
    @X5claus 4 ปีที่แล้ว

    Thank you for showing this, I am a german car tech and di dnot know how to do it, there is another video showing the whole rear deck has to come out, me and my fist would like to meet him.

  • @ActinOut
    @ActinOut 11 หลายเดือนก่อน

    Thank you! Agreed. The level of stupidity of hyundai engineers in designing this is astounding.

  • @blah064
    @blah064 2 ปีที่แล้ว

    Had to replace the rear door handle and that was a nightmare. Of the screw fell into the door skin, would have been ok trouble.

  • @bachle2536
    @bachle2536 5 ปีที่แล้ว +1

    you should put into the description or as a pinned Comment for the size. I think it is 921 bulb, right?

    • @jimthecarguy
      @jimthecarguy  5 ปีที่แล้ว +1

      Thanks for watching .Will do.

    • @ToddTinley
      @ToddTinley 5 ปีที่แล้ว

      T10 LED. So you don't have to do it again for a long long time.

  • @andrewdutton3831
    @andrewdutton3831 2 ปีที่แล้ว

    04:55 to 05:29....put that on a continuous loop....that's me doing this repair job.

  • @descontracao6566
    @descontracao6566 ปีที่แล้ว

    Thanks, buddy.

  • @dustinderrick1480
    @dustinderrick1480 3 ปีที่แล้ว

    Thanks saved me some money!

  • @maxbanuelos1181
    @maxbanuelos1181 5 วันที่ผ่านมา

    thank you! life saver

    • @jimthecarguy
      @jimthecarguy  2 วันที่ผ่านมา

      You're welcome, I'm glad the video was helpful!

  • @dxdn_yt
    @dxdn_yt 2 ปีที่แล้ว

    Thank you!

  • @johnpowell1952
    @johnpowell1952 4 ปีที่แล้ว

    Can someone help me pls. Hyundai i20 third brake light removal to replace bulb. Thank you John

  • @Farehaven
    @Farehaven 3 ปีที่แล้ว

    They should make that easier

  • @XCI-kb5mt
    @XCI-kb5mt 2 ปีที่แล้ว

    Well done sir! You helped us out A LOT! Indeed it was a pain in the ass..and i did lost my temper instead of you! Hahaha! Greetings from Greece!

  • @vitalitybypaul6966
    @vitalitybypaul6966 4 ปีที่แล้ว

    Thanks Jim! Why does it have to be so difficult?!?!

  • @hekthic
    @hekthic 2 ปีที่แล้ว

    unscrew it instead of prying the assembly it comes out a lot easier.

  • @Sam-qg1dy
    @Sam-qg1dy 4 ปีที่แล้ว

    Don't know if this guy is right. I forced the plastic without taking screws off and then realized that it might be possible to take out light from inside trunk. Try that first!!! It's way to hard to put it back otherwise.

  • @OnCall24Seven
    @OnCall24Seven 4 ปีที่แล้ว

    Thank you Jim!!!

  • @jwilkers1
    @jwilkers1 5 ปีที่แล้ว

    Thanks for the insight on this one