Understanding Router LEDs | Tips & Tricks

Blinking LEDs provide lots of information about your device status from a glimpse. In this video we will introduce you to LED codes for Teltonika Networks devices!
More about RUTX11 - teltonika-networks.com/produc...
Timestamps:
0:00 Introduction
0:17 General LEDs information
1:17 Troubleshooting sequences
1:43 Outro
Subscribe to @TeltonikaNetworks: / @teltonikanetworks
Website - teltonika-networks.com
Wiki - wiki.teltonika-networks.com/
Crowd-Support Forum - community.teltonika-networks....
CONNECT WITH US:
Subscribe to Our Newsletter - teltonika-networks.com/subscr...
Linkedin - / teltonika-networks
Facebook - / teltonikanetworks
Instagram - / teltonikanetworksofficial
Twitter - / teltonikanet

[@TRACEROOTGPS]

Good Information ✅

[@TeltonikaNetworks]

Thank you.

[@RobertoBonettoik1zyq]

I have a RUTX09, what does it mean if the 5 signal LEDs flash constantly?
The network seems to be working but the LEDs are flashing, thanks for your possible response

[@TeltonikaNetworks]

Thank you for your question. Signal LEDs usually flash when the router is booting up or during device reset procedure. If your device’s LEDs flash constantly, I would recommend trying to reflash the firmware through bootloader. More information on the procedure could be found here: wiki.teltonika-networks.com/view/RUTX09_Device_Recovery_Options#Bootloader_menu
If this suggestion does not help, feel free to contact us through your sales manager or write to us on our Crowd support forum.

[@c4manke]

I had a couple that would not power on straight from factory, diving deeper I found a burned copper ribbon imbedded in the board, I jumpered the capacitor it was going to, to the power in and it seems to work. Any reason they would fail straight from factory?

[@TeltonikaNetworks]

We are sorry to hear about this. If you have received a defective device, please contact your supplier so that we can either fix it for you or replace it with a new one.

[@albertkomar]

👍👍👍

[@TeltonikaNetworks]

👍

[@Neosense]

We have the RUTX11 in use and what I am really missing is a possibility to determine, what WAN is actually used. At the moment, if the router has an LTE Connection and the WAN port is connected, both led light up, but you can't determine, which of the two is being used. Would be really nice, if the active/used one would for example blink slowly

[@TeltonikaNetworks]

Thank you for the suggestion. Currently we do not have such functionality/indicators that would allow you to determine which type of WAN is being used on the device. However, that is possible via the WebUI in the Network -> Interfaces section.
Network interfaces RUTX11: wiki.teltonika-networks.com/view/RUTX11_Interfaces
Note: Priority is top to bottom

[@meyer-venter]

Hi, I have the RUTX11 in my van and after a view days leaving the rougher unplugged, it won’t start up. Only the ä PWR LED is on, everything else stays off and the router isn’t starting at all ☹️
What can I do to get it back up and running?

[@TeltonikaNetworks]

Hello. That is very unusual behavior. You could try using the recovery options wiki.teltonika-networks.com/view/RUTX11_Device_Recovery_Options
If that will not help. You should contact the device reseller.

[@martinliebermann1889]

Hi. If my signal strength leds are not lit does that mean the tower is not talking to the router?

[@TeltonikaNetworks]

Hey. If no signal-strength LEDs are lit, that means the signal is very weak. You can find more information about Signal strength LEDs on this page: wiki.teltonika-networks.com/view/RUT950_LEDs#Signal_strength_LEDs

[@Fadlan356]

Hello , would like to know ... what normally LTE router use for ?
because what i know the router is using cable not using LTE

[@TeltonikaNetworks]

Greetings. For various different use-cases that involve remote locations, or LTE connectivity as backup connectivity, and many more. You can find all our real-life use-cases at our website: teltonika-networks.com/industries/use-cases/

[@pawelmatyja]

What does the PWR LED flashing every second mean? after updating the software (firmware and modems), the PWR LED flashes every second and no other LEDs. The second device behaves the same. You don't describe this behavior anywhere in the manual...

[@TeltonikaNetworks]

Could you please get in touch with our engineer team at the Community Support Forum. community.teltonika-networks.com/ They would be more than happy to help!

[@gl0omygo0ber]

I hard reset and now both the 3g and 4g are blinking at the same time.

[@TeltonikaNetworks]

You should check your SIM card. If the SIM card is in the device, you need to check if the SIM does not require a PIN code.
If the SIM card requires a PIN code you must enter the SIM PIN in Sim cards settings here: wiki.teltonika-networks.com/view/RUTX11_Mobile#SIM_card_settings