Overall, this is a highly informative and enjoyable video for anyone interested in engineering. It showcases your talent and expertise while providing valuable insights and inspiration to fellow enthusiasts. Keep up the great work, and I look forward to watching more of your content in the future 👍👍👍
Not the best in the world at all, no quality, no safety every thing is covered in dirt most things are put together with a hammer nothing is clean, people work on the floor. Cheap and nasty.
@@panza. I doubt that guy at the welder would get fired. You can see he is young and inexperienced. He actually came in shop in leather shoe! That's big no, no in Pakistan. We all know that main PPE piece of every good Pakistani worker are slippers! He even dared to wear real welding gloves. That minimalist cardboard mask would not help him. Very unpleasant conversation with the boss awaits him. 🤣🤣🤣
Цилиндр с мощным поршнем, двухстороннего действия, если будет работать на выталкивание под нагрузкой, проблем не будет, но если под нагрузкой втягивать шток, тогда может оторвать по сварке, ибо шов с наружи, фаски не сняты, был опыт, с ремонта получали, сами потом снимали фаски насквозняк и проваривали. А так ребята молодцы 👍.
Amazing stuff! Like me, I'm sure when you think of where hydraulic cylinders are made, you envision a big huge spotless facility where most everything is done by robots. But here we see it all done with pride by hand. Would I purchase one these handmade cylinders if they were available in the US? Without a doubt! Thank for showing us. Great vid!
These things will kill someone. He destroyed the heat treatment on that rod with the torch. That entire Cylinder is compromised simply because of that but I see many other issues that are absolutely life-threatening. Imagine that cylinder is holding up several tons and the rod snaps in half because the carefully heat treated steel has been softened with a blow torch to god knows what strength. Or the seals blow and you suddenly lose pressure and your excavator arm comes crashing down because they used a rusty pipe full of dirt instead of a honed precision pipe. Or that weld breaks on the end cap shooting it across the room with 5000 psi. (5000 psi x 5sqin = 25000 lbs of force or roughly as much as a 50 BMG bullet).
@@excitedbox5705 se fosse nos EUA seria difícil ver alguém fabricando mesmo tendo bastante recurso agora eu duvido alguém ser tão criativo igual os países de 3 mundo onde se cria homens fortes
@@excitedbox5705 And you should not damage the rod by rolling it against steel and ground or put it in lathe chuck without aluminium covering rod. Worst was when using lathe as a milling machine, he fasten rod with screw. Now there is screw mark on the rod. It doesn't take much to break that surface and then leaky leak. When doing thread in lathe, you should use some kind of a lubrication. Your tool will last longer. We have different standards.
When l worked in a manufacturing shop just after high school, the last 20-30 mins of each day was spent cleaning up - everything. The owner/ boss said 'let your workplace be the mark of your professionalism - if the workshop looks like a dog's breakfast, customers will think your work is as well'. Sound advice l carried throughout my career. First thing l noticed was the state of this workshop - eek!
Luke, your boss used clichés and you are taking that literally for a place in a third-world country where labor is super cheap and these men worked their asses off to produce a product equal to or better than what your boss produced at a much higher cost per unit. Go take your clean shop somewhere else!!!
Man , cuelga un vídeo tuyo , ahí se ve la diferencia , ellos le dan valor agregado a la materia prima i así se aprende , yo pienso sus hijos lo realizarán en otro nivel
I know the title says "hydraulic cylinder" but they clearly meant "Pneumatic" The tube wall thickness and the welds are not for a hydraulic cylinder. Also, note the cushion on the piston and the thin wall tube.
youre a complete idiot, these are absolutely hydraulic cylinders. The wall thickness is very typical for cylinders in excavators and farm machinery. As for the welds, arc welding has better penetration than mig or tig in most cases and is fine in this application. If anything welding on a pneumatic cylinder has to be better than on a hydraulic cylinder due to having to seal gas leaks rather than thick hydraulic oil. Don't comment when you don't know what youre talking about.
@@kitramshaw5447 I was not refiring to the method of welding but the lack of preparation, no bevels all butt welds and they have a cushion on both ends, something not typically seen on hydraulic cylinders. I may not be as smart as you are but I am respectful at least.
@@thepubliceye Typically what would be the walk thickness for a pneumatic tube? I work with seals but not so much the cylinder itself. I noticed the piston u-cups seemed to urethane which would seem a little aggressive for a pneumatic application. This is a sincere question.
@@thepubliceye I give them kudos for the fairly quick turnaround in making a cylinder but, just from I know that it doesn't look like it would last very long. The surface finish would rip those seals apart.
Great video, but the safety standards here don’t exist unfortunately. No eye wear, no gloves, no boots, sleeves are over the spinning head. Wish you well.
I stop at minute 11:26. Definitely a remarkable expierience at the technical level of project execution. But I must say that the way they execute it is frightening. Ignore the most mundane safety measures... You can't work on a parallel lathe or milling machine with those garments... then so wide it's just scary! My question is, if they work with that philosophy, what will the finished product look like? With what safety do they work? I think it will be a disposable hydraulic cylinder. Working with those principles, they cannot guarantee a quality product. (Only an approximate product).
![How to make a hydraulic cylinder [ DIY ] * Subtitles *](http://i.ytimg.com/vi/T_36mR8bN5M/mqdefault.jpg)
Overall, this is a highly informative and enjoyable video for anyone interested in engineering. It showcases your talent and expertise while providing valuable insights and inspiration to fellow enthusiasts. Keep up the great work, and I look forward to watching more of your content in the future 👍👍👍
Su trabajo en equipo me encanto, un aplauso!!!
Ты сам крут, и сварщик у тебя профи! 👍
Пацан норм варит!!!! Тоже железом занимаюсь, респект!!!
Токарь очень грамотный и опытный, из токарного станка сделал фрезерный! Работает четко быстро, ни одного лишнего движения
What a team work. Excellent process and well presented. Pakistani technicians are the best in the world.
Not the best in the world at all, no quality, no safety every thing is covered in dirt most things are put together with a hammer nothing is clean, people work on the floor. Cheap and nasty.
I doubt that.
@@panza. I doubt that guy at the welder would get fired. You can see he is young and inexperienced. He actually came in shop in leather shoe! That's big no, no in Pakistan. We all know that main PPE piece of every good Pakistani worker are slippers! He even dared to wear real welding gloves. That minimalist cardboard mask would not help him. Very unpleasant conversation with the boss awaits him. 🤣🤣🤣
Vcs são um gênio,,Deus os abençoe com muito mais sabedoria...
Amazing hans at work. Would i be wrong to say father and son?
african are proud of you guys looking forward one day you guys will build a car for global market . keep it up guys
Cars are easy, we are trying to get to space.
Parabens estou aprensendo mais com voces ; sou torneiro ferranebreiro aqui brazil !
Amazing works dear guyzz
Merci beaucoup mon ami 💐 merci pour le partage de cette belle vidéo intéressant, très bon travaille, bravo bon courage et bonne chance 🙏🙋💐🙏
Цилиндр с мощным поршнем, двухстороннего действия, если будет работать на выталкивание под нагрузкой, проблем не будет, но если под нагрузкой втягивать шток, тогда может оторвать по сварке, ибо шов с наружи, фаски не сняты, был опыт, с ремонта получали, сами потом снимали фаски насквозняк и проваривали. А так ребята молодцы 👍.
Team yang sangat profisional, semoga sehat.
Mis respetos saludos desde Jalisco México
these guys can make an industry of hydraulic cylinders
Thank you for this interesting video. The know how is remarkable.
удивительно что его не разматало с его рукавами
Top show parabéns pelo seu trabalho 👏🤝💖🇧🇷🇧🇷🇧🇷🇨🇮👍
its so cool, and amazing work,
Thank you very much ❤
Parabéns. Serviço de primeira
Amazing stuff! Like me, I'm sure when you think of where hydraulic cylinders are made, you envision a big huge spotless facility where most everything is done by robots. But here we see it all done with pride by hand. Would I purchase one these handmade cylinders if they were available in the US? Without a doubt! Thank for showing us. Great vid!
you want to kill yourself?
These things will kill someone. He destroyed the heat treatment on that rod with the torch. That entire Cylinder is compromised simply because of that but I see many other issues that are absolutely life-threatening. Imagine that cylinder is holding up several tons and the rod snaps in half because the carefully heat treated steel has been softened with a blow torch to god knows what strength. Or the seals blow and you suddenly lose pressure and your excavator arm comes crashing down because they used a rusty pipe full of dirt instead of a honed precision pipe. Or that weld breaks on the end cap shooting it across the room with 5000 psi. (5000 psi x 5sqin = 25000 lbs of force or roughly as much as a 50 BMG bullet).
@@excitedbox5705 se fosse nos EUA seria difícil ver alguém fabricando mesmo tendo bastante recurso agora eu duvido alguém ser tão criativo igual os países de 3 mundo onde se cria homens fortes
@@excitedbox5705 And you should not damage the rod by rolling it against steel and ground or put it in lathe chuck without aluminium covering rod. Worst was when using lathe as a milling machine, he fasten rod with screw. Now there is screw mark on the rod. It doesn't take much to break that surface and then leaky leak.
When doing thread in lathe, you should use some kind of a lubrication. Your tool will last longer. We have different standards.
@@excitedbox5705why’d he use that torch anyway?
Excellent job
Well done 👍
You guys are very good in what you doing
ماشاءاللہ بہت خوب اور بہت عمدہ طبیعت خوش ہو گئی۔
آپکا پتہ کیا ہے۔
Good . I liked and subscribed .
Молодцы, класс!!!
excellent lathe and drill work without safety goggles.
Наше Сколково будет догонять их по нано ещё лет 10
Да если вообще догонят😂😂😂.
Gerçekten uzun ve zor bi süreç
Kolaylıklar diliyorum
Nice job!
ฝีมือน่าทึ่งมากๆ
Good to see that he still has vision, operating a lathe without safety goggles for example...
7:34 Pra que destemperar o aço ??🤔🤔
It probably normalized for easier cutting. The rest is harden so it would not bend.
Very nice 👍
first class work gentleman,and great skills.well done.
no
So dumb
@@onetiretom 👍👌
yep, that's how proper DIY should be done!
😂👍
Excellent job, you guys do great work...
На токаре всё производство держится.
Where are you from? I´m Brazilian
Dzień dobry .jak szlifijecie cylinder bo nie było pokazane .pozdrawiam z PL.
Qual material é esse que você está fazendo a haste do cilindro
When l worked in a manufacturing shop just after high school, the last 20-30 mins of each day was spent cleaning up - everything. The owner/ boss said 'let your workplace be the mark of your professionalism - if the workshop looks like a dog's breakfast, customers will think your work is as well'. Sound advice l carried throughout my career. First thing l noticed was the state of this workshop - eek!
Luke, your boss used clichés and you are taking that literally for a place in a third-world country where labor is super cheap and these men worked their asses off to produce a product equal to or better than what your boss produced at a much higher cost per unit. Go take your clean shop somewhere else!!!
My shop in America doesn't look much better 😂 I keep my stuff clean and organized but no one else does
@@nabman5619 8w 8e 3di on q83g di 3angkat gk qd
@@nabman5619 3t g delete 1
d830qa
One can get Arc-Eye jus from watching this video 😵💫😎
تمام قسم کی جیک سیل کٹ کہاں سے ملیں گی
Через столько минут сотрутся уплотнительные кольца и манжеты об внутренности водопроводной трубы?
Может, как-то обработана была?
Впрочем зеркалу тоже хана.
Там саму трубу быстрее давлением порвет
Personal safety equipment on verry high level 😅 ! Otherwise good skils.
Pl tell me name of lathe opprater
No entiendo cómo estas personas no le dan más importancia al orden y a la limpieza. Yo sería incapaz de trabajar en ese ambiente.
Man , cuelga un vídeo tuyo , ahí se ve la diferencia , ellos le dan valor agregado a la materia prima i así se aprende , yo pienso sus hijos lo realizarán en otro nivel
Give the guy in the orange a pay raise!
I know the title says "hydraulic cylinder" but they clearly meant "Pneumatic" The tube wall thickness and the welds are not for a hydraulic cylinder. Also, note the cushion on the piston and the thin wall tube.
youre a complete idiot, these are absolutely hydraulic cylinders. The wall thickness is very typical for cylinders in excavators and farm machinery. As for the welds, arc welding has better penetration than mig or tig in most cases and is fine in this application. If anything welding on a pneumatic cylinder has to be better than on a hydraulic cylinder due to having to seal gas leaks rather than thick hydraulic oil. Don't comment when you don't know what youre talking about.
@@kitramshaw5447 I was not refiring to the method of welding but the lack of preparation, no bevels all butt welds and they have a cushion on both ends, something not typically seen on hydraulic cylinders. I may not be as smart as you are but I am respectful at least.
@@thepubliceye Typically what would be the walk thickness for a pneumatic tube? I work with seals but not so much the cylinder itself. I noticed the piston u-cups seemed to urethane which would seem a little aggressive for a pneumatic application. This is a sincere question.
@@RetroGamingJebus I agree you are correct, so it looks as though they used what they could get, I guess it's a very poor hydraulic cylinder.
@@thepubliceye I give them kudos for the fairly quick turnaround in making a cylinder but, just from I know that it doesn't look like it would last very long. The surface finish would rip those seals apart.
Real Ironman...
Why is necessary warm one of sides of piston ?
So that it can be machined, otherwise the metal is too hard.
the smartest guy is the one who welds,,,, shoes glasses and gloves
You make América Honduras
what is the price of hydraulics cc 3 tons and 2 tons
Asallam o alikum
Weldon the power steering cylinder construction I like it but without sefety both
Mashallah bhai
ما شاءالله تبارك الرحمان
Can someone tell me which welding rod use in 17:35
Сварщик не индус! Сварочные краги, обувь закрытая и маска на шарнире.
Токарь тоже штангенциркулем пользуется!!!
Читеры))
я тоже обратил внимание обычно они в шлепках работают,даже акумуляторы
Perooo hay faltaba probar el funcionamiento yo nose si el vástago sale y vuelve ha entrar YO VI TOOODO EL PROCESO PERO NO VI QUE FUNCIONARA IGUALMENTE
من الجزائر
أهم شئ انه لم يملس جوف الأسطوانة
كيف ستنجح؟
bom trabalho 👏👏
❤❤❤❤😊😊😊Ок
Nice job n nice video...tq done like n subscribe
I built hydraulic cylinders if our shop looked like that you’d be laughed out of the industry!
Your location ??
2:40 Legend
Realy good and hard work pr ise test bhi kriye bnne k baad
Na test Na control Na contact. Ta k gaaan Na wajjan
Ah, that's where Harbor freight gets it's cylinders
I Can Ask how much money for have Factory liké this
Great video, but the safety standards here don’t exist unfortunately. No eye wear, no gloves, no boots, sleeves are over the spinning head. Wish you well.
Если скажут что у меня на рабочем месте бардак, то я покажу им этот видос.
Круто!
Але умови потребують кращого.
He has some hours in the lathe!!
wow amazing 😮
Hmmm. Red nuts to check the thread. Is that in some way related to blue balls? !ol
also, mention contact details for acquiring services of repairing etc plz
Very skilful mechanic, don’t see any safety protection for him, at least a pair safety glass.
👌👌👌👌👌👌👌
todo a mano
Good job big work
no
15 টন হাইড্রলিক কত দাম
I stop at minute 11:26. Definitely a remarkable expierience at the technical level of project execution. But I must say that the way they execute it is frightening. Ignore the most mundane safety measures... You can't work on a parallel lathe or milling machine with those garments... then so wide it's just scary!
My question is, if they work with that philosophy, what will the finished product look like? With what safety do they work? I think it will be a disposable hydraulic cylinder. Working with those principles, they cannot guarantee a quality product.
(Only an approximate product).
Покажите как работает.
No importa como esté el taller si ellos saben lo que están asiendo en ese país no asen falta robots ellos reciclan todo o lo reparan.
Esse cara de camisa vermelha e bone tem muita cara de ser BR kkkkk
INGENIOUS
no it isn`t
@@imtheeastgermanguy5431 sure is
@@rand0mGT no its all wrong and dangerous
Лайк.
1 meter long hydraulic body
Impressive
👍👍👍👍👍👍👏👏👏👏👏
Reporté del Pdv12 pozos activos y sin novedades
Не дай Бог такой гидроцилиндр попадётся
А какой? тебеж какой втюхают, такой и поставишь.
Super 👍👍👍👍👍👍👍 😻😻😻😻😻😻😻 💯💯💯👏👏👏👏👏
Неге барі жұмысты отырып жасайды
Меня этот вопрос постоянно мучает, это же такая нагрузка .
Joe much ton capacity