PRECIOUS TIP : when you put back the panel, BEFORE closing the door, TEST the door handle and lock are both working properly. If you close the door and realize a handle doesn't work because the cable inside is stuck or not correctly attached, it will be too LATE - you won't be able to open the door to remove the panel. Ask me how I know. I brought a car to a shop who didn't attach the lock knob and put the panel back and closed the door. Oops
I did fix my 2005 S60 change door opening mechanism, it had as You said "nonreusable" door clips. I took them out by using nylon thread and didn't damage any. If You have brains they are reusable.😂 Hope this helps someone!
One of my rear doors clicks constantly when the car is in motion. I traced the noise to the top of the door card where it meets the inside window seal. I hope that when I take off the door card I find something loose that I can fix to stop the clicking.
Thank you so much. I have a 2007 XC70 and as you mention it appears to have the cheaper clips with no push-pin. I would appreciate if you could give guidance as to how to remove these clips that do not have a push-pin? Should I slide my trim pry tool under the head of the clip? Or should I slide my trim pry tool under the edge of the door panel? I appreciate your attention to detail, all the other instructions do not recognize that the 2004-and-up push-pins do not have the centre pin. Fellow Canuck here by the way, in Sudbury.
All years have clips with a center pin that must be pushed in. Your year has a thinner center pin - watch closely in the center to see it - and you need to push it all the way in until it falls inside the door, then the clip comes out and just pry the panel off the door frame. Watch at 6:30 You will probably not retrieve the center pins so get in advance replacement clips
@@Peppermint1 I just finished removing and reinstalling the front door panel n my 2007 XC70. In my case I did not lose the pins inside the door. The receptacle part of the clip is a closed sheath. So when I pushed the center pin all the way out of the clip, it was retained within the sheath. The entire assembly(sheath, clip, pin) then pulls out of the door panel, and you can pull the clip out of the sheath and retrieve the pin. I was able to reuse all my clips.
rattle from inside door? if the original speaker has been removed, it may cause rattle, the window glass may also be a little loose inside. suggest asking here www.matthewsvolvosite.com/forums/viewforum.php?f=26&sid=0fb2b71af28ff6e8dad6eff7f7956a18
Hello, hopefully u respond because I accidentally broke the door lock thing when removing the door panel. So I’m jus wondering if u could give me a link to that part so I could buy a new one. Or just some example that fixes the problem
Hi! My driver's door pull handle on my 2004 XC70 needs to be replaced. Do I have to remove the entire door panel to attach the new door pull handle? The pull handle snapped off and left the part connected to the door panel in place, so the door pull handle is in 2 halves. I ordered a replacement pull handle but I'm worried about removing the door panel without breaking something. Is there an easy way to fix without removing the door panel? Thank you!!
Do you mean the exterior handle ? You need to remove the interior door panel then the plastic insulant to have access, and replacing the handle may not be easy. If you rather meant the inner door handle, this is how to fix it th-cam.com/video/Jd7JNhUrD1g/w-d-xo.html
People like to place a piece of metal shaped like a 'C' over the two plastic tabs that secure the handle cable. Some glued this piece of metal in place which should be a permanent fix - the downside is it won't be possible to remove the door panel again in the future if needed. On mine I just placed such metal piece tight, without glue. Here's a forum where this is discussed www.matthewsvolvosite.com/forums/viewtopic.php?t=20732
Thanks Again MAESTRO... YOUR ACCENT,...RUSSIA?...BUT I NOTICED A CANUCK FLAG IN THE BACKGROUND OF ONE OF YOUR BUTTER KNIFE EXPEDITIONS... SPEAKING OF BUTTER KNIVES... YOU(WE) SHOULD ETCH VOLVO ON THE BLADES OF BUTTER KNIVES FROM: GOODWILL, THE STARVATION ARMY OR THE DOLLAR STORE AND SELL EM FOR 49.95$ EACH..... AS A VOLVO SPECIALTY TOOL?
Volvo would have no problem asking $50 for a butter knife for sure. Just the stamp would be $48. The accent is a mix of Romanian, Quebec French and Quebec English
PRECIOUS TIP : when you put back the panel, BEFORE closing the door, TEST the door handle and lock are both working properly. If you close the door and realize a handle doesn't work because the cable inside is stuck or not correctly attached, it will be too LATE - you won't be able to open the door to remove the panel. Ask me how I know. I brought a car to a shop who didn't attach the lock knob and put the panel back and closed the door. Oops
You have saved my 2002 V70 more than once - thank you for making these videos.
Most welcome
Sir- thank you so much for this... I repaired my handle without spending 100s at the dealership - well done sir... Well done!
Faleminderit shumë, Video e juaj më ka ndihmuar shumë!👍
Welcome
Great video, great job showing and explaining everything
I did fix my 2005 S60 change door opening mechanism, it had as You said "nonreusable" door clips. I took them out by using nylon thread and didn't damage any. If You have brains they are reusable.😂 Hope this helps someone!
Thanks for sharing the tip
Thank you for this! Exactly what I needed to know!
chers
Thankyou sir for the video
My 2004 xc70 has those type of door panel clips.
One of my rear doors clicks constantly when the car is in motion. I traced the noise to the top of the door card where it meets the inside window seal. I hope that when I take off the door card I find something loose that I can fix to stop the clicking.
I just bought 2004 Volvo door panels(all 4).Can I use them to replace those on my 2002 Volvo?Its the same model s60
Please aswer the last question below if you can. No center pin on my XC70 2006..how to remove panel then?
Thank you so much. I have a 2007 XC70 and as you mention it appears to have the cheaper clips with no push-pin. I would appreciate if you could give guidance as to how to remove these clips that do not have a push-pin? Should I slide my trim pry tool under the head of the clip? Or should I slide my trim pry tool under the edge of the door panel?
I appreciate your attention to detail, all the other instructions do not recognize that the 2004-and-up push-pins do not have the centre pin. Fellow Canuck here by the way, in Sudbury.
All years have clips with a center pin that must be pushed in. Your year has a thinner center pin - watch closely in the center to see it - and you need to push it all the way in until it falls inside the door, then the clip comes out and just pry the panel off the door frame. Watch at 6:30 You will probably not retrieve the center pins so get in advance replacement clips
@@Peppermint1 Thanks again!
@@Peppermint1 I just finished removing and reinstalling the front door panel n my 2007 XC70. In my case I did not lose the pins inside the door. The receptacle part of the clip is a closed sheath. So when I pushed the center pin all the way out of the clip, it was retained within the sheath. The entire assembly(sheath, clip, pin) then pulls out of the door panel, and you can pull the clip out of the sheath and retrieve the pin. I was able to reuse all my clips.
Hi peppermint y have an s60 2011 and have some problem with Ind noise on Doors do You know how to silve IT pls It Drive me crazy
rattle from inside door? if the original speaker has been removed, it may cause rattle, the window glass may also be a little loose inside. suggest asking here www.matthewsvolvosite.com/forums/viewforum.php?f=26&sid=0fb2b71af28ff6e8dad6eff7f7956a18
Mersi frumos
Thank you! Very helpful!
Hello, hopefully u respond because I accidentally broke the door lock thing when removing the door panel. So I’m jus wondering if u could give me a link to that part so I could buy a new one. Or just some example that fixes the problem
Look in the description of this video th-cam.com/video/Jd7JNhUrD1g/w-d-xo.html
Hi! My driver's door pull handle on my 2004 XC70 needs to be replaced. Do I have to remove the entire door panel to attach the new door pull handle? The pull handle snapped off and left the part connected to the door panel in place, so the door pull handle is in 2 halves. I ordered a replacement pull handle but I'm worried about removing the door panel without breaking something. Is there an easy way to fix without removing the door panel? Thank you!!
Do you mean the exterior handle ? You need to remove the interior door panel then the plastic insulant to have access, and replacing the handle may not be easy. If you rather meant the inner door handle, this is how to fix it th-cam.com/video/Jd7JNhUrD1g/w-d-xo.html
super hlelpful thanks!
👍
The interior door opening lever always break from the terrible plastic inside. Do you have a more permanent solution?
People like to place a piece of metal shaped like a 'C' over the two plastic tabs that secure the handle cable. Some glued this piece of metal in place which should be a permanent fix - the downside is it won't be possible to remove the door panel again in the future if needed. On mine I just placed such metal piece tight, without glue. Here's a forum where this is discussed www.matthewsvolvosite.com/forums/viewtopic.php?t=20732
@@Peppermint1 Thanx for the tip : )
@@legambaz Welcome
do u know if a 04 door panel would be work with a 06?
Thanks!
God bless
Thanks Again MAESTRO...
YOUR ACCENT,...RUSSIA?...BUT I NOTICED A CANUCK FLAG IN THE BACKGROUND OF ONE OF YOUR BUTTER KNIFE EXPEDITIONS...
SPEAKING OF BUTTER KNIVES... YOU(WE) SHOULD ETCH VOLVO ON THE BLADES OF BUTTER KNIVES FROM: GOODWILL, THE STARVATION ARMY OR THE DOLLAR STORE AND SELL EM FOR 49.95$ EACH..... AS A VOLVO SPECIALTY TOOL?
Volvo would have no problem asking $50 for a butter knife for sure. Just the stamp would be $48. The accent is a mix of Romanian, Quebec French and Quebec English
The door panel isn't the same on my '08 XC70.
The 2008 XC70 and V70 are P3 platforms, only the S60 was made to 2009 as P2 platform (as in the video)
Because the 2008 is a smaller v70 xc model.