Thanks for the vid really helped my understanding in the next vid could you possibly show the gear need to write to the chip and some data logging if possible I gave you a sub bro nice vid ✊🏾
So dumb question I haven’t downloaded the program yet so it bolted on anything, so I’m running stock engine as can be My question is in the videos I’ve seen it looks like I can adjust the injectors and put a launch control, is there any benefit for my f22b1? I plan to put in a bigger fuel pump and change the injectors to about 400cc or so I just didn’t know if it’s advisable I wanna push it as far as it can go without cracking the block or anything
@@DIYKAI that’s fair I can see that I plan a tear down and want to build it back up, but from what I’m seeing finding parts that are budget friendly and finding things compatible are hard For the most part stock parts like timing and gaskets are easy but I do want to find forged pistons heads and rods maybe bore it out a bit but I don’t see it adding much hp I see kits for springs and plan to send my camshaft and rockers to delta cams to make it a stage 2 Eventually it’ll get there but first I want it to pop
@@DIYKAI well I thought about hollowing it out and spacing the 02 sensor to prevent a code but that’s a no no and I don’t recommend anyone doing that 😉 But mines a 97 so I’ll still need emissions but I’m definitely leaning towards bigger injectors and replacing fuel lines and pump since it is a 20+ year old vehicle
Your welcome. So alot can happen from not starting to running lean to rich.....get a wideband if you start messing with anything you need to watch AFR stock is 14.7
I can't get my car to start.. the check engine light goes on only when I step on the gas and goes away when I let off to try and start it when it cranks.. but I noticed I can't calibrate my tps sensor only let's me check the box to set a custom tps value.. I set my decapped ls injectors at 450cc and deadtimes to rc750cc 12ohms and took out my resistor box.. its what huntertuned told me to set them at
@@DIYKAI stock motor stock f23a block with stock f22a head. Obd1 chipped p06 non vector ecu, using honda tuning suites. Just installed turbo, hunter tuned decapped ls injectors, quantum 255lph fuel pump, stock fuel pressure. I set the com ports to com4 and com3 and I am able to connect the data logger now and the tps is able to calibrate also but still no start but my battery died so ill have to wait to try again..
@@righty-tightybuilt548 yes fully charge the battery and leave it hooked up until started and running.....as far as everything else pull the plugs you may have to adjust the fuel tip in at start-up.....also make sure you calibrate the TPS otherwise things can be off then get your base timing dialed in
Sir could you make a video about p29 ecu launch control and popcorn setup.Thanks a lot .l need help so could you give me your email adresss for ask something p29 ecu remap????
@@DIYKAI l make a p29 basemap with honda tuning suite software But l cant make setup low high cam settings injector iggination setups.just Hts' p29 stock rom basemap enough for car or we must setup fuel and iggnation settings?
@@DIYKAI I was referring to HTS... I've tried to get familiar with it but the windows aren't showing everything... For example on the settings window where you choose the units displayed for the various tables/ graphs it only show half of what's written... I can't enlarge any of the windows.... I've tried the cursor on every corner and nothing happened... I've looked for a solution online bit it seems that it's just me who can't make them bigger.... I've tried 3 versions of HTS without luck....
You would not believe how much this has already helped me, thanks!
Your welcome!
Glad there are people like you 🙂
Thanks! Knowledge is only good if you share it!!
Smoothing map its very helpful understanding hts colums and good settings.Thanks so much Brudasssss.
Your welcome I'm doing some more repair videos if you haven't already subscribed please do
@@DIYKAI l am gonna follow you :)
Really informative step by step video bud look forward to the next
Thank you! The next one will be actual chip burning and what devices I use.
@@DIYKAI exactly what i wanna see haha doing a z6 turbo build the next coming months so yourll be helping massively
Great 👍 basemap video and explanations!
Thanks! 👍
Sub to my channel more to come!
Subbed up
Same
Greatly appreciate it! Not many videos on on to use HTS. Thank you! Will you do a video on setting up 2 step?
Yes more videos to follow in order next will be burning a file to chip, then datalogging and so on. Stay tuned! Thank you!
I have a few videos on hts as well if willing to spend the time to watch. One is on popcorn decel
So true, there are not really any in depth tutorials on hts which is surprising.
Thanks for the vid really helped my understanding in the next vid could you possibly show the gear need to write to the chip and some data logging if possible I gave you a sub bro nice vid ✊🏾
Your welcome, yes absolutely the next video will show how to write the file to the chip
I have a old datalogging one I made if you want to check it out. I will make new ones.
So dumb question
I haven’t downloaded the program yet so it bolted on anything, so I’m running stock engine as can be
My question is in the videos I’ve seen it looks like I can adjust the injectors and put a launch control, is there any benefit for my f22b1?
I plan to put in a bigger fuel pump and change the injectors to about 400cc or so
I just didn’t know if it’s advisable
I wanna push it as far as it can go without cracking the block or anything
If your motor is stock then tuning is not required, hard launches will break things lol
@@DIYKAI that’s fair I can see that
I plan a tear down and want to build it back up, but from what I’m seeing finding parts that are budget friendly and finding things compatible are hard
For the most part stock parts like timing and gaskets are easy but I do want to find forged pistons heads and rods maybe bore it out a bit but I don’t see it adding much hp
I see kits for springs and plan to send my camshaft and rockers to delta cams to make it a stage 2
Eventually it’ll get there but first I want it to pop
If you just want the snap crackle pop……make sure you are ready to replace the catalyst if short time unless your running straight pipe then your fine
@@DIYKAI well I thought about hollowing it out and spacing the 02 sensor to prevent a code but that’s a no no and I don’t recommend anyone doing that 😉
But mines a 97 so I’ll still need emissions but I’m definitely leaning towards bigger injectors and replacing fuel lines and pump since it is a 20+ year old vehicle
Thanks for this dude can i ask something? What happened to engine if u dont know how to tuned?
Your welcome. So alot can happen from not starting to running lean to rich.....get a wideband if you start messing with anything you need to watch AFR stock is 14.7
With that serious damage can occur from bent rods to broke ring lands or pistons.
Thanks for this bro i watching ur videos right now without skipping ads thankyousomuch broooo! ☝️💥
@@MarkRensoSoriano your welcome let me know if you have any other questions
well this video has aged but i have a d16y7 what engine should i select in the basemap creator or am i not supported?
You can use z6 map and turn off vtec and adjust from there
@@DIYKAI sweet thanks man. abought to lock vtech in my engine so im gona need to
tune
Your welcome make sure your have a wideband o2 to monitor everything
If you would be using a chip burner how do you burn chip?
th-cam.com/video/aV81fQRNohw/w-d-xo.html
th-cam.com/video/YjV16J9FU48/w-d-xo.html
Can i use Honda tuning suite on a demon2
I think so
I can't get my car to start.. the check engine light goes on only when I step on the gas and goes away when I let off to try and start it when it cranks.. but I noticed I can't calibrate my tps sensor only let's me check the box to set a custom tps value.. I set my decapped ls injectors at 450cc and deadtimes to rc750cc 12ohms and took out my resistor box.. its what huntertuned told me to set them at
So many variables…motor set up? Ecu type? Stock TPS and map? Built motor? Turbo?
@@DIYKAI stock motor stock f23a block with stock f22a head. Obd1 chipped p06 non vector ecu, using honda tuning suites. Just installed turbo, hunter tuned decapped ls injectors, quantum 255lph fuel pump, stock fuel pressure. I set the com ports to com4 and com3 and I am able to connect the data logger now and the tps is able to calibrate also but still no start but my battery died so ill have to wait to try again..
@@righty-tightybuilt548 yes fully charge the battery and leave it hooked up until started and running.....as far as everything else pull the plugs you may have to adjust the fuel tip in at start-up.....also make sure you calibrate the TPS otherwise things can be off then get your base timing dialed in
Will this work to honda fi motorcycles?
I am not sure sorry
As long as you using one of the listed ECUs it should
hello, where I can get the software to download?
What country are you in?
@@DIYKAI phlippines
If you can Google HTS
@@DIYKAI thanks
Sir could you make a video about p29 ecu launch control and popcorn setup.Thanks a lot .l need help so could you give me your email adresss for ask something p29 ecu remap????
Hello I do not have a p29 but can make a similar one on a p28.
To make a basemap you just find the ecu code the closest in your case p28
@@DIYKAI l make a p29 basemap with honda tuning suite software But l cant make setup low high cam settings injector iggination setups.just Hts' p29 stock rom basemap enough for car or we must setup fuel and iggnation settings?
@@meditationlife9337 it's enough to start the car but you need a wideband o2 to tune it and datalogging
Am I the only one who can't enlarge the windows and can only read half of what's written inside????
Not sure when I do I can? What device are you watching on?
@@DIYKAI I was referring to HTS... I've tried to get familiar with it but the windows aren't showing everything... For example on the settings window where you choose the units displayed for the various tables/ graphs it only show half of what's written...
I can't enlarge any of the windows.... I've tried the cursor on every corner and nothing happened... I've looked for a solution online bit it seems that it's just me who can't make them bigger....
I've tried 3 versions of HTS without luck....
@@goncalofonseca5935 never experienced this🤔 and you cant enlarge by dragging at the center of the window line?
@@DIYKAI I just tryed the corners... I'll try dragging on the center as you suggested.... Thank you for the tip...
@@goncalofonseca5935 cool lmk if it dont work I can try to help some more