Rope making stick/club
ฝัง
- เผยแพร่เมื่อ 27 ก.ย. 2024
- In this video I show you how to make a rope making stick/club and use it to make rope.
This video was inspired by an instructable by Asemery.
Making rope using this basic tool teaches you how rope is built and how it works. It is a great activity both for learning and passing the knowledge on to your kids.
Enjoy the video!
Мастер - просто ОГОНЬ ! Столяр 2 - го разряда , не более : инструментарий это ещё не всё ...
Very interesting. I've seen old photos of waterfront rope making sheds, now I know how it was done and why the buildings where so long. Thank you
Good comment! Indeed, rope making facilities were made very long. The Chatham ropewalk for example was one of the longest buildings built for a long time. They made 1000 foot rope!
Mark
I lost my mobile.. call me Gary.
I am impressed by the sharpness of that knife and the expertise of the tool user! Fascinating! Do you have knowledge of when and where this tool and technique were used? It seems such a simple tool yet it produces one of the most universally needed and used items, cord or rope. Possibly one of humanity’s first great inventions!
Thank you. That is wonderful to see. I never knew about this method. This is a much more approachable method than many of the others out there. Thanks again!
Thanks! I am going to try this out.
wonderful video 👍🙏
I use a similar method but on a much longer base when I’m teaching this to the scouts. Also, with a longer base, I’m able to fold the twine two or three times to make much heavier ropes. Sometimes I’ll even twist three or four ropes into a cable.
Good video and very interesting
Thank you for the video. I’d like more information on the three and four strand options and the two attachment points. When you using to attachment points do you just attach them and then use the club to spin and then once the Rope is tied combined the strands and remove the second attachment point and then spin counterclockwise?
Wow, very interesting! I guess I would be in trouble if I wanted to end up with a 100’ rope !
Neat video. I have a couple of questions:
1. Would this tool be "one size fits all", for different widths of twine?
2. What is your advice on the number of turns clockwise and counterclockwise? Should they be roughly the same?
Think you i'm firs like in this video 😁👍
He made the spinning device more complicated than it should be. All you is a screw in hole slightly larger than the screw.
Good
Instead of using masking tape, could just tie off the end with whipping with the same twine.. thanks for the vid, now I understand better
genius
Zone
Excelente obrigado 👏🏽👏🏽👏🏽🤝👍
+++
Doubling, twisting and tripling is great, but you should have increased tension in the original cord used.
K is silent
Dude. You have a drill. Attached a metal loop into your drill like a bit, and use that to twist your twine to make the rope. No need for your primitive tool. Sorry.
They probably have a proper rope making machine, too. Your comment speaks of ignorance as this video is about a tool. And this tool needs no power or electricity other than what you provide, that's something most modern drills can not provide. It is also quiet. And there is tremendous beauty in simplicity
@@HaileISela como caca
As mentioned, your comment is rather ignorant. Many people enjoy learning about traditional tools and methods. And yes, beauty in simplicity.
@@TomeOfKnowledge74 hey Tommy-go-figure...your comment is rather naive and uninformed, much more ignorant than any page of "tome" you deem to possess.
@@georgesedeno7891I wasn't belittling you. Ignorance, as in needing education, and as I intended it, is not an insult. I was pointing out that just because you have a tool doesn't make it the best or only method to get a job done. Your open mindedness is also indicated in how you respond to criticism (also not a negative or insult).