Hello bro, the Media Converter is basically a device where you connect the SFP module to establish the fiber connection. So you will need both the SFP GPON module (if your ISP deploy GPON) and the Media Converter (to conver the fiber signal to Ethernet - if router router doesn't have a SFP port)
If you ask the question, most likely you will not see any benefit from it,, but in short it permits you to switch the ISP router which usually offer very basic configurations on the user side, for a more advanced router as a PfSense or Ubuiti systeme where you can manage basically everything on your network. Also for big wi-fi coverage, usually the provide box is sub-par in speed and coverage
Mostly for neatness sake, your router would be able to directly connect to the WAN rather than have to go through a modem or your ISP's router. And you wouldn't be bottlenecked by either but that's not why I did, I did for the cosmetics reason
I saw all your videos of this thing, help me a lot for the config of my latinq SFP but now I'm checking really high temps using an hex s What media converter are you using? Do you have some recommendations?
Hi Van. Please just let me know if this SFP module will work in my network environment. It is a 11 building condominium where the ISP working under dark optic fiber providing 4000 Gigabytes that goes to the MDF where the OLT is located, from there spread to each building to a splice, from the splice to each building apartment APC type fiber to a Corning model 7298 SDAN 8 ports from GE01 to GE08, from the Corning to an AP station. Means this is a sharing ISP network. I do have my own network lab rack with the connection straight from GE01 to my server, just unplugged out the AP and turned off, with my own internal static IP. into a ER605 dual Wan low balance controller with a fail-over Cradlepoint 5G CPE as secondary ISP. Well my point is when I disconnect the APC type fiber out the Corning SDAN device and plugged into the HSGQ GPON FSP module to the 2500M network adapter automatically gets GPON Status O5 LOID Status=Initial Status with non configurations needed, the R6S NanoPi gets RX-3900Pkts/ RT-700Pkts. But connection attempt fail in PPPoE mode or DHCP either way, I'm using the R6S NanoPi with three Ethernet ports from right to left Wan-Lan1/2.5G, Lan2, HDMI, USB-CPD . What is missing here, or this is not possible with this ISP network sharing configuration. I've tried already the WAN option eth2.1 throughout 1000, mean not Vlan's works from 1 to 1000. Thanks for your answers in advance
It is different. HSGQ/ODI GPON/EPON/XPON modules are from the same company HSGQ. You can change most of the GPON parameters such as GPON Serial Number, PLOAM Password, MAC address, SW/HW ver, etc
Hi I just got edgerouter 4, and i wanted use it as a replacement of onu i got, so where i can finde it I search on Amazon, and I couldn't finde it or other sfp you using in your tutorial I live in the middle east can you help me please
IGMP là một giao thức chạy trên bộ định tuyến, switch, v.v. SFP này chỉ đơn thuần là chuyển đổi tín hiệu quang thành điện nên bản thân nó sẽ không hỗ trợ IGMP. Nếu nhà mạng/OLT có luồng UDP cho IPTV => bạn sẽ nhận được ở luồng này tại SFP/ONT. Trong kênh mình có 1 video nói về IPTV trên OpenWrt, bạn có thể tham khảo qua.
I've got the exact sfp stick like yours. Plugged it in my Archer BE800 and there's no way I can access the sfp stick to set it up. Is there any chance to get through, mate?
I have no idea, you need to find a Media Converter, or use a router that support firewall rule, such as Mikrotik or OpenWrt. In this video I use OpenWrt
Hello Van Tech, i hope u can help me. i ditched my ISP ONU, and im currently using a VSOL ONT with a openwrt router. My ISP provides internet and telephone via voip, and everytime bridge ONU reboots openwrt router get a ip from VOIP range (10.XXX.X.XX), and because of this i have to restart wan interface to get a internet IP. is there anyway to fix this on openwrt?
You might want to check VLAN settings, assuming the ISP uses different VLANs for Internet/VoIP/IPTV, just contact a technician or look on your local forums
I believe your firmware is out of date. I have model DFP-34X-2C2 Firmware Version which is V1.2.2-221209. It's has IP6 and a menu of options across the top, you need to maybe speak to someone to update as I found I had to do this when I got my unit, the sellers sent me the file. They are quality devices. And great value.
para Telmex utiliza el (ubiquiti ufiber loco) a si yo quite el router de Telmex. la ont y el router lo tengo por separado. también tienes que tener el usuario y contraseña pppoe
@@rolandomota7474 clonar el número de serie y la mac de router qué te instaló telmex en ubiquiti ufiber loco. Con el programa ufiber configurator. Este canal tiene un video de como hacerlo
@@abrahamgarcia1051 dónde compras el ufiber loco, al parecer están descontinuados, yo conseguí un Nokia G-010S-A , pero tienes que entrar por su webpage para cambiar las cosas o por SSH y con línea de comando. Ese me lo regalaron básicamente , pero si no puedo conseguirle un unifiber loco. Usado
Not really, if you compare the price. I also reviewed the LXT-010S-H on the channel. 2 of them, the HSGQ SFP and LEOX SFP are still working fine until today.
isp ont is a default device, it’s convenient but there are case when your device is better. For instance, when use isp ont then dms traffic is manipulated with isp (mit) but with my own router I can use doh, dot for better control.
![[#2024MAMA] ROSÉ (로제), Bruno Mars - APT. | Mnet 241122 방송](http://i.ytimg.com/vi/dgGqD28J6aQ/mqdefault.jpg)
halo bro saya dari indonesia mau bertanya apakah semua Media Converter SFP supord dengan gpon sfp modul ?
Hello bro, the Media Converter is basically a device where you connect the SFP module to establish the fiber connection. So you will need both the SFP GPON module (if your ISP deploy GPON) and the Media Converter (to conver the fiber signal to Ethernet - if router router doesn't have a SFP port)
Boy-oh-boy. In 2018 internet in Danang was dial-up level. I'm moving back!
Yeah, I pretty much forgot what the rest of the video was about at 12:10. 🤤
Nice video! Do you have any 10G or 2.5G XGS-PON SFP stick to recommend?
So far no, because I don't have a chance to test the XGS-PON for now. If there is any update, I will let you guys know.
Is there any available xpon onu 10G?
is there any good reason to replace the one from ISP provided one with our SFP module?
If you ask the question, most likely you will not see any benefit from it,, but in short it permits you to switch the ISP router which usually offer very basic configurations on the user side, for a more advanced router as a PfSense or Ubuiti systeme where you can manage basically everything on your network. Also for big wi-fi coverage, usually the provide box is sub-par in speed and coverage
Mostly for neatness sake, your router would be able to directly connect to the WAN rather than have to go through a modem or your ISP's router. And you wouldn't be bottlenecked by either but that's not why I did, I did for the cosmetics reason
Do I need the media converter to access the SFP via its IP or can I put this to any other router/switch (e.g. Cisco switch) and connect to it?
I saw all your videos of this thing, help me a lot for the config of my latinq SFP but now I'm checking really high temps using an hex s
What media converter are you using? Do you have some recommendations?
is this compatible with my isp which uses huawei ont and olt?
Hi Van. Please just let me know if this SFP module will work in my network environment. It is a 11 building condominium where the ISP working under dark optic fiber providing 4000 Gigabytes that goes to the MDF where the OLT is located, from there spread to each building to a splice, from the splice to each building apartment APC type fiber to a Corning model 7298 SDAN 8 ports from GE01 to GE08, from the Corning to an AP station. Means this is a sharing ISP network.
I do have my own network lab rack with the connection straight from GE01 to my server, just unplugged out the AP and turned off, with my own internal static IP. into a ER605 dual Wan low balance controller with a fail-over Cradlepoint 5G CPE as secondary ISP.
Well my point is when I disconnect the APC type fiber out the Corning SDAN device and plugged into the HSGQ GPON FSP module to the 2500M network adapter automatically gets GPON Status O5 LOID Status=Initial Status with non configurations needed, the R6S NanoPi gets RX-3900Pkts/ RT-700Pkts. But connection attempt fail in PPPoE mode or DHCP either way, I'm using the R6S NanoPi with three Ethernet ports from right to left Wan-Lan1/2.5G, Lan2, HDMI, USB-CPD . What is missing here, or this is not possible with this ISP network sharing configuration. I've tried already the WAN option eth2.1 throughout 1000, mean not Vlan's works from 1 to 1000. Thanks for your answers in advance
Is this Transceiver compatible with 10G sfp+ port in RT-AX89X ASUS router?
hi. that was so great. Where did you get the APC version? which store sell this stick in europe?
Do you know if you have a XGS PON version available ?
Where did you get the APC version ? All HSGQ and ODI around are UPC. Thank you.
May I know which country you are living in and how many pcs you need? I can share some info then
What’s the difference between a normal ONU and and ONU Stick?
MAC Key what is 1.9a is it same for all or where can I get it?
My provider offers internet at a specific VLAN and VOIP over another VLAN, how to configure that?
odi Ram 64M có tốt hơn hsgq ram 32M ko bạn
Сделан так же как Хуавей? так же греется сильно? Он имеет свой личный SN-GPON?
It is different. HSGQ/ODI GPON/EPON/XPON modules are from the same company HSGQ. You can change most of the GPON parameters such as GPON Serial Number, PLOAM Password, MAC address, SW/HW ver, etc
Dear Van, I couldn't find HSGQ SFP XPON ONU Stick can you help me to buy it please
Hello, what is the best bang for the buck setup, is it possible to do that someday? great video for begginers!
Hi
I just got edgerouter 4, and i wanted use it as a replacement of onu i got, so where i can finde it
I search on Amazon, and I couldn't finde it or other sfp you using in your tutorial
I live in the middle east
can you help me please
Hey, if you are in the Middle East, you can get a similar module from LEOX. See the LEOX LXT-010S-H, and the contact also available in my video.
Your line network is 1gpbs right ?
Is there an xgs-on stick that is built like this? I need an XGS-pon stick that has this ability because my ISP provider has an XGS-PON network.
So far no, because I don't have a chance to test the XGS-PON for now. If there is any update, I will let you guys know.
How to change ONU ID?
how do i connect voip? the sfp stick nor the media converter does not have rj11 port.
For VOIP, I will suggest using the ONT with RJ45/RJ11 port instead.
Con này có hỗ trợ IGMP cho luồng ip tivi không bạn ?
IGMP là một giao thức chạy trên bộ định tuyến, switch, v.v. SFP này chỉ đơn thuần là chuyển đổi tín hiệu quang thành điện nên bản thân nó sẽ không hỗ trợ IGMP. Nếu nhà mạng/OLT có luồng UDP cho IPTV => bạn sẽ nhận được ở luồng này tại SFP/ONT. Trong kênh mình có 1 video nói về IPTV trên OpenWrt, bạn có thể tham khảo qua.
Hi! Can you try Anime9000 firmware?
I've got the exact sfp stick like yours. Plugged it in my Archer BE800 and there's no way I can access the sfp stick to set it up. Is there any chance to get through, mate?
I have no idea, you need to find a Media Converter, or use a router that support firewall rule, such as Mikrotik or OpenWrt. In this video I use OpenWrt
@@VanTechCornerhi Van. Exactly. A media converter works like a charm . Thanks, mate
can i have link to buy 2.5G media converter with cheapest price in vietnam?
Hi, you can get it from here shope.ee/20URLhVscZ
Disclaimer: This is not my store. All the support and warranty should be provided by the seller.
Mạng FPT thì clone S/N và MAC Address thôi đúng ko bạn?
một số nơi, còn chẳng cần đổi gì, cứ gắn vào chạy.
Hello Van Tech, i hope u can help me. i ditched my ISP ONU, and im currently using a VSOL ONT with a openwrt router. My ISP provides internet and telephone via voip, and everytime bridge ONU reboots openwrt router get a ip from VOIP range (10.XXX.X.XX), and because of this i have to restart wan interface to get a internet IP. is there anyway to fix this on openwrt?
You might want to check VLAN settings, assuming the ISP uses different VLANs for Internet/VoIP/IPTV, just contact a technician or look on your local forums
Can I use SFP+ 10G module? Does it support? Or might become incompatible with the OLT?
Hi NafJanT, did you test with 10g module?
@@cheloeskeici no bro. Not yet.
will this work with XGS pon ?
Hi, this module will not work with XGS PON. There are SFP modules supporting XGS PON, but I haven't got any so far.
HSGQ is not being detected by intel x520-d2, any way to solve this? Tried forcing the stick to 1g also
Hey, did you try to contact the seller and get the newest version.
Yes, I'm on V1.1.8-240408
Know a vendor who will ship the DFP-34X-2C2 to India?
Tanks for this video ,need help I have O5 but LOID STATUS WRONG ,INFO SAME SFP XPON HSGQ with edge router x stp solution please
I believe your firmware is out of date. I have model DFP-34X-2C2 Firmware Version which is V1.2.2-221209. It's has IP6 and a menu of options across the top, you need to maybe speak to someone to update as I found I had to do this when I got my unit, the sellers sent me the file. They are quality devices. And great value.
can you please send me the new V1.2.2-221209 firmware
@michaeljarcher Yup you are correct. I haven't update the stick when making this video.
Updating to 221209 version crippled my Internet. I had to downgrade it to the same firmware as Van's
Does this work for mexico telmex, their integrated ont router sukkk big time! , i got a mikrotik hex with sfp cage
para Telmex utiliza el (ubiquiti ufiber loco) a si yo quite el router de Telmex. la ont y el router lo tengo por separado. también tienes que tener el usuario y contraseña pppoe
@@abrahamgarcia1051 tienes que clonar todo vdd, número de serie del router de Telmex , conseguí un ont sfp nokia
@@rolandomota7474 clonar el número de serie y la mac de router qué te instaló telmex en ubiquiti ufiber loco. Con el programa ufiber configurator. Este canal tiene un video de como hacerlo
@@abrahamgarcia1051 dónde compras el ufiber loco, al parecer están descontinuados, yo conseguí un Nokia G-010S-A , pero tienes que entrar por su webpage para cambiar las cosas o por SSH y con línea de comando. Ese me lo regalaron básicamente , pero si no puedo conseguirle un unifiber loco. Usado
Where did you buy this SFP? I am living in Hanoi and I want to buy this SFP to explore.
Hi, you can get it from here shope.ee/20URLhVscZ
Disclaimer: This is not my store. All the support and warranty should be provided by the seller.
@@VanTechCorner Thank you very much! Your channel extremely useful and easy to understand.
Can you tell me which model support 10gbe?
LEOX is better, what are think?
Not really, if you compare the price. I also reviewed the LXT-010S-H on the channel. 2 of them, the HSGQ SFP and LEOX SFP are still working fine until today.
giọng ông này nghe giống ông bên youtube cytron ghê :v
Nó đó bạn ơi :D
Where can I buy this SFP module?
Hi, may I know which country you from? You should be able to get it from aliexpress or taobao.
@@VanTechCornerZimbabwe
@scholes2693 Hi, my friend. I do have this SFP for sale in 168$ the piece let me know if you are still interested. Thnx
Hello everyone, where can I buy this model HSGQ-XPON-Stick(APC), the one that appears in the first seconds of the video.
Hi, did you buy it. There are plently of it on AliExpress, Taobao and eBay (slightly expensive).
@@VanTechCorner Hi friend, the APC model is not available, I already searched for it
Can you simplify why you need to replace your isp ONT?
For flexibility. of course, default ONT from ISP work fine.. but fine tuning can't be done with standard ont.
You can’t replace ont won’t work with isp hardware
isp ont is a default device, it’s convenient but there are case when your device is better. For instance, when use isp ont then dms traffic is manipulated with isp (mit) but with my own router I can use doh, dot for better control.
is this singlish i hear?
Nope, this is Vietnamese-English, mixed with little bit Malaysian-Chinese English since I worked in Malaysia for some years.
Bác người Việt Nam ạ
Đúng rồi bác. Mình là người Việt Nam nha.
This Gpon cant support QinQ vlan and PVID
I guess you are talking about the ODI, not the HSGQ (newer model). Also, make sure you got the latest firmware from factory where it should work.
Hay không ấy mình làm kênh tiếng việt được không bạn?
made in china
ofc lol
Does it really important? iPhone, Google Pixel, most of the computer mainboards and electronic stuffs are also made in China.
@@VanTechCornerexactly.
Don't buy HSGQ olt
Hanging problem
This product can be connected to mikrotik 5009
Yes it is. It had been tested working fine.
Will this work if I put it into the sfp wan port on my UniFi dream machine se?
It should work.
I have a USG PRO4 and it the HSGQ SFP module works fine.