Does this come with a screen protector pre-installed. I just got mine and it looks like it has it on it, but I'm afraid to mess with it. If it's on it from the factory, then it's so perfect it's hard to tell.
@@WTFRCCars Thanks man, it was so hard to tell if it was pre-install. I peeled off the sticker and was like... hmmm. I guess it's just that perfectly on there, well done Flysky.
Yes that would be a good video, i have seen somewhere that the new transmitter NB4 Pro+ is about 500 to 600 USDollars, then the cheaper NB4+ will be my choice if i can choose
I am struggeling with the decision top. I want to go racing indoor and outdoor and need a new transmitter. I don‘t need many Channels for my RCs but the set up changing by pressing one Button is really interesting. Does the nb4+ for this Feature? And where do you get the skins for the transmitter?
Man you're channel is what single handedly made me choose the nb4+ a couple months ago and I absolutely love it. I have a question though ive got the ibus2 gyro rx with the ibus2 extender to run all the telemetry sensors i wanted to have. Ive also got a few of the older sensors as well that can be daisy chained together. Am i able to read both the ibus2 and the non ibus2 sensors or is it one or the other? Since ive got the other sensors i figured I'd try them for reading bulkhead temps in hopes of somewhat monitoring differential temps. I couldn't seem to get the signal from the non ibus2 sensors though and im still new at this.
The none ibus 2 sensors will need to be connected to a socket set to ibus not ibus 2 for you to be able to read them but I'm not sure if you can set both ibus in one socket and ibus 2 on another at the same time as this would be a lot of work for a receiver to do and keep low latency but try it and see if you can get both
@@WTFRCCarsdang thanks for the lightning fast reply. I kinda figured that was the case but also knew who to ask lol. One thing I'd like to get the word out on too is that if you have any ibus1 temp sensors and damage a ibus2 temp sensor like i did you can solder the actual thermal sensor end of the old style to the new style and so far it seems to work fine after about 20 packs run through it. Probably not ideal but i tried it in a pinch and so far its been dead on to what my infrared gun reads.
As always very indepth and to the point. What impressed me was the new colorful display compared to other models and the PL18. Is this maybe an OLED screen or is the firmware revamped for this new look? If so do you have 'inside' information if the PL18 will get a look like that in the next fw update? Or any of the others? Or perhaps the IPS LCD screen can't handle that?
As far as I know it's just a brighter back light and re design of the screen colours and layout, as for the PL18 and EV I'd love to see them get software to match but haven't seen any plans for this from flysly
@@WTFRCCars Thanks for the reply. Ditto. But first I would like them to fix the timer bug in the PL18 FW. The throttle, i.e. J3, used as timer trigger setting won't be saved at shutdown and needs to be set again every time on restarts. Have you noticed that also?
@klausmewes3622 yeh just had time to check it out and it definitely does not work after a re start until you select J3 throttle again I will get a vid done and get flysky on it :)
Hi. So what’s the difference between the Noble Pro and Noble Pro+ except the colour? I watched 1/2 of the video but so far the same as the Noble Pro. I got that charger for my pro… Any chance there is a firmware update for the pro to get the logic switches?
Main difference is brighter screen, higher resolution throttle, usb c base, trainer mode and the logic switch set up, as for the pro I don't see it getting new features in firmware now the + is out and it's no longer in production
Bro, please make a video on how to connect rhe lighy system to nb5 pro.. I have a rgt rescuer and it has light system which iwould like to map to nb4 pro..
Hello, Just switched from Futaba to Flysky and would like to know which receivers should I buy for my 1/8 bashers, 1 crawler and one 1/10 basher. I sometimes also race, but only with friends. I was looking at FGr4D, FGr4B and the one with a Gyro, the INr4-GYB.
Bashers I'd run the inr4-gyb cos the SVC is fantastic, crawlers the new waterproof 8ch is a good choice FBR8, anything racing fgr4d is great but just run whatever makes sense in that RC :)
What receiver would you suggest that will work 100% with this NB4 Pro+ for say a Traxxas X-Maxx, XRT and or Kraton 6S? Wondering if you have a goto Receiver for this and your other Flysky NB4s’?
Really depends if you want SVC or not, for me I'm not really bothered about SVC on a basher so if you looking for 100% waterproof then the Fbr8 is a good choice, the Fgr8b works great too, if your after SVC the inr4-gyb is the one you want :)
@@WTFRCCars also if I get the gyro model inr4 you can turn off the svc via transmitter easily anyhow correct? Kinda like option of gyro on the 1/5th bashers…
Hey Craig, quick question. I just recently ordered the NB4+ hand wheel for my NB4 and was wondering: what is really the size difference between the L and the normal hand wheel? I kinda want to try a larger hand wheel but don’t want to order it if there’s not that significant of a size. I’m willing to give Sour Sky a chance after they’d screwed me on my shipping but I don’t want it to be the same terrible experience.
The large wheels is alloy part is roughly the same size as the normal wheel including the foam so when it's like adding another foam on top of the stock size wheel doesn't sound much but definitely feels a good bit bigger
Do you have direct contact with Flysky? The link for the following firmware is wrong "STD Firmware v1.0.6(EN version)", you get a version 1.0.7 for the NB+ not Pro+. I sent them a mail, but no reaction.
Yeh loads of telemetry options and it can record data to so you can check after the run but also set alarms to you don't run too hot or battery too low
How on earth do k set my NB4 + engine kill switch up? Iv tried everything Iv read, watched etc…I have a 1T hilantronics kill switch and got this radio gear as was told it’s the cream of the crop….I can’t assign the kill switch for the life of me, never had this issue with anything before, even th e cheapest of cheap radios has been more user friendly than this regarding kill switch setup. It just won’t work. Any help would be awesome before this nb4 + goes against the wall 😝
It's easy, assign a button to ch3, set it to toggle so it makes the channel go 100 to -100 then connect your kill switch to ch3, if it doesn't work it's because your kill switch is slow and can't keep up with the transmitter so goto servo frequency and turn it to custom and lower it to 333hz :)
@@WTFRCCars thanks for your reply. Iv done all this already though after watching your stuff on your channel. It genuinely doesn’t work for me, tried it all. Iv assigned it to whatever the button is called on the right side of the steering wheel, made sure it operates as a switch rather than momentarily, it’s on channel 3 in my receiver and assigned to channel 3…tried digital, analogue, changed the frequency several times to different values, still won’t do anything mate. Losing the will to love with it haha
@GazYT1285 Try setting to 60hz some really slow kill switches need it that low but also have you tried a servo on ch3 to make sure it's going full in both directions?
@@WTFRCCarshi mate, still no joy with it. I’m starting to think the 1T Hilantronics kill switch isn’t compatible as it just won’t work. Iv watch all of your videos to do with the nb4 range, it just won’t have it
Was just about to buy nb4+ as tired of waiting and saw the pro + on ali, came straight here after 🤭❤ Wonder how long before uk has stock 🤔 back to waiting 🙄😂
…i would never ever never in this updated open source modern times…buy a rc radio of any kind…thats restricted and locked into a branded protocol…as this flysky radio…i own lots of open source updated elrs protocol multi module 4 in 1 rc radio transmitters…although wish for a radiomaster mt12 with a turnable steering wheel…this will probably never happend…i will have to diy disect and cut up and reshape one of my mt12…to make this happend…wish me luck…
I know exactly what ya mean, but try being into motorbike and ebikes too lol think it will be around the £400 to £450 ish I know the CN version in AliExpress is £399
Does this come with a screen protector pre-installed. I just got mine and it looks like it has it on it, but I'm afraid to mess with it. If it's on it from the factory, then it's so perfect it's hard to tell.
Yeh all the nb4 + and pro have one on :)
@@WTFRCCars Thanks man, it was so hard to tell if it was pre-install. I peeled off the sticker and was like... hmmm. I guess it's just that perfectly on there, well done Flysky.
Can you do a comparison with the nb4+ and the nb4+pro
Yep will definitely be doing one in the future
Yes that would be a good video, i have seen somewhere that the new transmitter NB4 Pro+ is about 500 to 600 USDollars, then the cheaper NB4+ will be my choice if i can choose
@kenblockx2010 yeh really depends if you need the extra features of the pro+ or not. The nb4+ is all most people need :)
I am struggeling with the decision top. I want to go racing indoor and outdoor and need a new transmitter. I don‘t need many Channels for my RCs but the set up changing by pressing one Button is really interesting. Does the nb4+ for this Feature?
And where do you get the skins for the transmitter?
@Valadur83 skins are from soarsky, and the condition setting is only on the pro and pro +
Thanks for a great video!! Question.....how can I make SW2 and SW3 as momentary hooked up to Ch3 for winch control?
Same as on the pro th-cam.com/video/Ty4GsVE7wJs/w-d-xo.html
Thank you!
I have a receiver that does not recognize ch2 servo ive got it set as ch3 4 wheel steer to get it going have you had this before? Thanks
Nope all mine work fine and I have over 30 receivers, have you updated the firmware on the receiver?
Man you're channel is what single handedly made me choose the nb4+ a couple months ago and I absolutely love it. I have a question though ive got the ibus2 gyro rx with the ibus2 extender to run all the telemetry sensors i wanted to have. Ive also got a few of the older sensors as well that can be daisy chained together. Am i able to read both the ibus2 and the non ibus2 sensors or is it one or the other? Since ive got the other sensors i figured I'd try them for reading bulkhead temps in hopes of somewhat monitoring differential temps. I couldn't seem to get the signal from the non ibus2 sensors though and im still new at this.
The none ibus 2 sensors will need to be connected to a socket set to ibus not ibus 2 for you to be able to read them but I'm not sure if you can set both ibus in one socket and ibus 2 on another at the same time as this would be a lot of work for a receiver to do and keep low latency but try it and see if you can get both
@@WTFRCCarsdang thanks for the lightning fast reply. I kinda figured that was the case but also knew who to ask lol. One thing I'd like to get the word out on too is that if you have any ibus1 temp sensors and damage a ibus2 temp sensor like i did you can solder the actual thermal sensor end of the old style to the new style and so far it seems to work fine after about 20 packs run through it. Probably not ideal but i tried it in a pinch and so far its been dead on to what my infrared gun reads.
@scottstalmack146 yeh most temp sensors use the same component on the end to measure the actual temp :)
Thanks for your videos! Purchased the nb4+. So far so good. Just wish it had wireless charging.
Any chance of getting the wireless battery?
Yeh soarsky sell them just get the one for the pro+ clips right on the nb4+
As always very indepth and to the point. What impressed me was the new colorful display compared to other models and the PL18. Is this maybe an OLED screen or is the firmware revamped for this new look? If so do you have 'inside' information if the PL18 will get a look like that in the next fw update? Or any of the others? Or perhaps the IPS LCD screen can't handle that?
As far as I know it's just a brighter back light and re design of the screen colours and layout, as for the PL18 and EV I'd love to see them get software to match but haven't seen any plans for this from flysly
@@WTFRCCars Thanks for the reply. Ditto. But first I would like them to fix the timer bug in the PL18 FW. The throttle, i.e. J3, used as timer trigger setting won't be saved at shutdown and needs to be set again every time on restarts. Have you noticed that also?
@klausmewes3622 yeh just had time to check it out and it definitely does not work after a re start until you select J3 throttle again I will get a vid done and get flysky on it :)
Can you buy the bigger wheel to fit on the nb4+ ? If so where at ?
soarskyrc.com/collections/noble-diy-kit/products/flysky-nb4-pro-l-size-steering-wheel
Hi. So what’s the difference between the Noble Pro and Noble Pro+ except the colour? I watched 1/2 of the video but so far the same as the Noble Pro. I got that charger for my pro… Any chance there is a firmware update for the pro to get the logic switches?
Main difference is brighter screen, higher resolution throttle, usb c base, trainer mode and the logic switch set up, as for the pro I don't see it getting new features in firmware now the + is out and it's no longer in production
@@WTFRCCars Ok, thanks! I run 1.01 firmware on my noble pro, worth updating to 1.07? What’s your opinion?
@scalebuilder_sweden yes always worth updating
What is the head tracker? And how does that work?
It's for the fpv headsets you can set the RC to follow instructions from the headset
@@WTFRCCars this can be any head tracking unit on the market?
@Crixman I've not had chance to check yet and I don't have any headsets
Bro, please make a video on how to connect rhe lighy system to nb5 pro.. I have a rgt rescuer and it has light system which iwould like to map to nb4 pro..
Light systems are easy with so many channels :)
Do you know if the FGr4S receivers are compatible with the NB4 Pro+ transmitter?
Yep work fine with it :)
Hello, Just switched from Futaba to Flysky and would like to know which receivers should I buy for my 1/8 bashers, 1 crawler and one 1/10 basher. I sometimes also race, but only with friends. I was looking at FGr4D, FGr4B and the one with a Gyro, the INr4-GYB.
Bashers I'd run the inr4-gyb cos the SVC is fantastic, crawlers the new waterproof 8ch is a good choice FBR8, anything racing fgr4d is great but just run whatever makes sense in that RC :)
@@WTFRCCars Thanks for the ultra fast response, really appreciate it :)
Will they ever sell the phone mount separately!?
Think soarsky may get them
What receiver would you suggest that will work 100% with this NB4 Pro+ for say a Traxxas X-Maxx, XRT and or Kraton 6S? Wondering if you have a goto Receiver for this and your other Flysky NB4s’?
Really depends if you want SVC or not, for me I'm not really bothered about SVC on a basher so if you looking for 100% waterproof then the Fbr8 is a good choice, the Fgr8b works great too, if your after SVC the inr4-gyb is the one you want :)
@@WTFRCCars appreciate that. Now last Q how about on your race buggy’s for track, what’s your goto Flysky RX there?
@@WTFRCCars also if I get the gyro model inr4 you can turn off the svc via transmitter easily anyhow correct? Kinda like option of gyro on the 1/5th bashers…
@shawnscott9704 yes the gyro/SVC is fully programmed from the transmitter so on/off or any of the settings can be changed :)
@shawnscott9704 fgr4d :)
Hey Craig, quick question. I just recently ordered the NB4+ hand wheel for my NB4 and was wondering: what is really the size difference between the L and the normal hand wheel? I kinda want to try a larger hand wheel but don’t want to order it if there’s not that significant of a size.
I’m willing to give Sour Sky a chance after they’d screwed me on my shipping but I don’t want it to be the same terrible experience.
The large wheels is alloy part is roughly the same size as the normal wheel including the foam so when it's like adding another foam on top of the stock size wheel doesn't sound much but definitely feels a good bit bigger
Do you have direct contact with Flysky? The link for the following firmware is wrong "STD Firmware v1.0.6(EN version)", you get a version 1.0.7 for the NB+ not Pro+. I sent them a mail, but no reaction.
Where you getting the link ?
@@WTFRCCars direct from the flysky homepage under downloads&upgrade für the pro+
Cool I didn't see any page for the nb4 pro + yet
@@WTFRCCars one which page you are looking?
I just updated from assistant v3 and works fine 1.0.6
Would like to know telemetry. Temp, rx volts, i use in my 5T 2.0
Rpm and future info
Yeh loads of telemetry options and it can record data to so you can check after the run but also set alarms to you don't run too hot or battery too low
You should do video on telemetry,
@Losi5t20 if ya look through the playlists I've done lots of em :)
How on earth do k set my NB4 + engine kill switch up? Iv tried everything Iv read, watched etc…I have a 1T hilantronics kill switch and got this radio gear as was told it’s the cream of the crop….I can’t assign the kill switch for the life of me, never had this issue with anything before, even th e cheapest of cheap radios has been more user friendly than this regarding kill switch setup. It just won’t work. Any help would be awesome before this nb4 + goes against the wall 😝
It's easy, assign a button to ch3, set it to toggle so it makes the channel go 100 to -100 then connect your kill switch to ch3, if it doesn't work it's because your kill switch is slow and can't keep up with the transmitter so goto servo frequency and turn it to custom and lower it to 333hz :)
@@WTFRCCars thanks for your reply. Iv done all this already though after watching your stuff on your channel. It genuinely doesn’t work for me, tried it all. Iv assigned it to whatever the button is called on the right side of the steering wheel, made sure it operates as a switch rather than momentarily, it’s on channel 3 in my receiver and assigned to channel 3…tried digital, analogue, changed the frequency several times to different values, still won’t do anything mate. Losing the will to love with it haha
@GazYT1285 Try setting to 60hz some really slow kill switches need it that low but also have you tried a servo on ch3 to make sure it's going full in both directions?
@@WTFRCCars thanks again for that info. Top man. Let me give that a go at some point tomorrow and I’ll come back to you. Cheers mate
@@WTFRCCarshi mate, still no joy with it. I’m starting to think the 1T Hilantronics kill switch isn’t compatible as it just won’t work. Iv watch all of your videos to do with the nb4 range, it just won’t have it
Was just about to buy nb4+ as tired of waiting and saw the pro + on ali, came straight here after 🤭❤
Wonder how long before uk has stock 🤔 back to waiting 🙄😂
Shouldn't be too long
@@WTFRCCars apparently only a few weeks wait 😮, ordered the pro+ from UK earlier today ❤🥳
As ever your have the best Channel for Flysky Reviews :-) I also use the noble pro from day zero and will buy the new pro+
Thanks 👍 and you will love the new pro +
@@WTFRCCars any idea when the EU Version is coming ?
@milan-racing the version I have is EU :)
I really learned a lot from your videos, thank you very much
Glad ya liked em :)
The text wtf rc cars?😢. Shame that that is on.
It's not it's only on mine cos flysky have them engraved for my TH-cam channel 😂
AWESOME VIDEO MAN THANK YOU FOR DOING IT 👍 CAN'T WAIT UNTIL I GET MINE!!! GOD BLESS YOU BROTHER ✝️ SINCERELY CLAY B.
No worries bro :) you will love it.
…i would never ever never in this updated open source modern times…buy a rc radio of any kind…thats restricted and locked into a branded protocol…as this flysky radio…i own lots of open source updated elrs protocol multi module 4 in 1 rc radio transmitters…although wish for a radiomaster mt12 with a turnable steering wheel…this will probably never happend…i will have to diy disect and cut up and reshape one of my mt12…to make this happend…wish me luck…
How about edge tx on the nb4 ;)
wow this hobby sucks it’s like a crack habit every time something gets released i need it more than food
any idea on rrp uk price
I know exactly what ya mean, but try being into motorbike and ebikes too lol think it will be around the £400 to £450 ish I know the CN version in AliExpress is £399
@@WTFRCCars i know mate mk1 golf gti robs me blind every chance it gets if that don’t rc cars will and don’t get me started on daughter lol
@renbarturbo yeh it's a hard life you us hobbyists lol