Hi Mike excellent video and I'm hoping it will be a life saver tomorrow, however when the door icon flashed was your door dead , could it only be opened manually or did it still work with the button or remote control ?
I repaired it. The wire had corroded where it attached to the graphite strip inside the rubber. I cut it open and managed to solder a new wire on to it. I then sealed it back up with superglue. It's still holding today, but the other side is now playing up! 😒
Hi Mike, thanks for the video, I’ve got the same problem and have been searching for a solution. Do you have any photos of your repair where the wires were corroded? Any help will be greatly appreciated. John
@@ogwamike no worries. I cut the rubber door seal quite low down on what looked like a horizontal seam and luckily this was where the wire had parted like yours due to corrosion. It was quite tricky to solder a very short piece of wire but eventually managed. Thanks to your video I knew what to look for and this resolved the problem. I did a few tests opening and closing the door as I found that the wire is quite sensitive to being in the right position in the rubber door seal to stop the automatically opening again as if something was detected. Once happy and door working correctly I super glued the opening I’d made in the door seal. Thanks again for your video 👍
I have a problem when it is cold or after a stop. the door does not want to open, it just opens it and when it is warm, it goes every time mistake 02356
I have this same problem..any idea how I remove the top connection?.. I can't see how I can get to it without removing the whole door!.. I've searched TH-cam, but no luck, any help would be much appreciated, TIA 👍
No, sorry, I've been real lazy. Even though the switch light it illuminated, it seems to work OK most of the time, so haven't got around to looking at it.
Спасибо мужик , что поделился опытом! Миру мир! Из Башкортостана
today I tried with 1220 Ohm and everything works without problems. Very explanatory video and very good. Thank you
Can you please share how you fix it?
Thank you. I had the same issue. Ordered a 1200 ohm resistor. And now we are back in action.
Thanks Mike I've the same issue will try what you have discovered
Did you ever repair the rubber? I have had 2 of these fail now and its getting expensive. Would ideally do you temp fix.
Hi Mike excellent video and I'm hoping it will be a life saver tomorrow, however when the door icon flashed was your door dead , could it only be opened manually or did it still work with the button or remote control ?
Great work mate ❤
Do you have any luck fixing it?
Did you manage to repair it or have you replaced it?
I repaired it. The wire had corroded where it attached to the graphite strip inside the rubber. I cut it open and managed to solder a new wire on to it. I then sealed it back up with superglue. It's still holding today, but the other side is now playing up! 😒
@@ogwamike that's great, I will have to try and give it a go myself. Thank you
Hi Mike, thanks for the video, I’ve got the same problem and have been searching for a solution. Do you have any photos of your repair where the wires were corroded? Any help will be greatly appreciated. John
Sorry, i don't. I'd already completed it before thinking that making this video could help others.
@@ogwamike no worries. I cut the rubber door seal quite low down on what looked like a horizontal seam and luckily this was where the wire had parted like yours due to corrosion. It was quite tricky to solder a very short piece of wire but eventually managed. Thanks to your video I knew what to look for and this resolved the problem. I did a few tests opening and closing the door as I found that the wire is quite sensitive to being in the right position in the rubber door seal to stop the automatically opening again as if something was detected. Once happy and door working correctly I super glued the opening I’d made in the door seal. Thanks again for your video 👍
@@jonip.21 great work! Is certainly was tricky, but think of the saving 😁
I have a problem when it is cold or after a stop. the door does not want to open, it just opens it and when it is warm, it goes every time mistake 02356
Hi as anyone got any photos of where they cut the rubber and photos of what to look for as I have no idea Thanks mark
Hi how many ohms is the sum of the resistors?
I can't remember exactly what I used, but it totalled about 1227 ohm.
Saya suka
I have this same problem..any idea how I remove the top connection?.. I can't see how I can get to it without removing the whole door!.. I've searched TH-cam, but no luck, any help would be much appreciated, TIA 👍
No, sorry, I've been real lazy. Even though the switch light it illuminated, it seems to work OK most of the time, so haven't got around to looking at it.