Adjusting sprinkler heads is not something I do often enough to recall the nuances of adjusting them. Your video is amazingly detailed on the procedures, as well as going directly to the important points. It was highly educational, easy to follow, and a pleasure to watch. Thank you!
Thank you! Thank you! Thank you! I have been having a devil of a time with our new sprinkler system. The installers didn't explain this much in detail, and I have two heads that are throwing too far onto bushes that are "low water required." It's been killing my bushes. Now I can reduce the throw distance of this 15ft-VAN and save my bushes! I am extremely appreciative for this educational video.
You are most welcome! I am glad our video helped! But remember the tip in the video: its always best to pick a spray nozzle of the correct distance since turning the spray down more than a few feet really messes up its watering efficiency. So if you need to turn your 15van down to 12 feet or less, its probably best to switch out the nozzle with a smaller one. Happy watering!
@@SmartIrrigation1 - Yes! Definitely noted. I measured the distance, and the sprinkler only needs to reach 12.5 feet in that area before hitting the bushes. Then I noticed that a 15ft half-circle was also spraying into the bushes at its farthest left corner. I reduced both of them and all seems to be much better! Hopefully my pittisporum bushes will get relief. I can increase the throw distance once we get to summer and the Texas heat scorches the bushes a bit too much. I'm just glad I know how to do it thanks to your video.
This is perfect! I am a first time home owner and have no idea what I am doing with lawn care. However, this one video probably just helped save my lawn as I am having watering issues. Thank you for taking the time to break this down and explain it very simple.
Finely I have found a video showing the correct RainBird sprinkler head the builder installed. I have an adjustable head that has not been watering an area and the grass has dried up. Installed sod and now for the adjustment. Thanks for this video showing me how to properly adjust. 😊🎉
You make it look so easy. Many of my sprinklers are 28 years old, the tops are not legible, and the grass (St. Augustine) has gotten so thick, that some of them can't even pop up. I need to put risers on? Some of them won't rotate anymore. Two of them broke off from the pipe. Trying to save $ by doing it myself, it's a b___h. It's only going to be 101 today, vs 103 yesterday, I should get going while it's still cool (83). Thanks for sharing, this was a very clear, easy to see video.
Haha thanks. You can put longer nipples on the spray bodies (perhaps we'll make a video on that in the future), or switch to a larger pop-up (like a 6"). And ones that don't rotate anymore will need to wither be cleaned out or replaced. Good luck!!
Thanks for watching! On the adjustable nozzles you can adjust them all the way closed and only a time stream will come out. But to further reduce the water, you can turn the distance adjustment screw clockwise until the stream basically stops (as long as a filter has been installed below the nozzle)
Great video! I have a question though, my stem doesn’t seem to go up much when I turn the system on, so it’s not getting about the grass. Any recommendations? Thank you!
If the spray has a stong flow coming out of it, It would not be a pressure or flow problem. In that case you probably have a head that is two low (deep) in the ground or it is a 2 inch popup or similar but in either case you would need the head, raised and replaced, or replaced if the head is just a short 2 inch.
Quick question I just had a sprinkler system installed a month ago and we have the fixed rain birds up along our house, but unfortunately, when the landscapers put them in, they also tied those to a side yard with grass so if I go lower on the amount of time I run them the grass gets less what I am trying to do is Have less water come out along the fixed ones in front of our house has bushes and rosebushes and other things By turning the screw clockwise, you describe in the video that it takes the pattern smaller is that also having less water come out of them? Thank you, sir
Thanks for watching! The distance adjustment on these sprays doesn't have a well-defined impact on precipitation rate (how much water is put down per minute); ideally you only use the screw to make a small 1-foot adjustment and that would have a negligible impact on the amount of water given. What you want to do is look for different spray nozzles that have different precipitation rates. One example would be to put in rotary nozzles in areas that need less water and keep the spray nozzles in the area that needs more water. Let us know how this works out for you!
Your explanation honestly makes it easy, so I subscribed. But I do have a question: I have no idea what brand of Sprinkler Rotors were put into the 2 zones about 7 years ago, but they do work. Can I use a Rainbird stationary nozzle on a Hunter Rotor shaft pop-up, or a Hunter stationary nozzle on a Rainbird Rotor shaft pop-up? I watched a video that said both Rainbird and Hunter use professional grade female thread pop-ups and nozzles.
Yes , brands of nozzels are interchangable on differing brands heads. This allows us to choose the best nozzel for the area to be covered regardless of brand. Check out our article on nozzel selection at smartirrigation.com if you like for some more info in this.
How about the height? I'd like my grass to be a little higher during the hot summer but my nozzles end up hitting the grass blades closest to the head eliminating spray further out. I can pull them up by hand high enough but they don't stay
Sounds like you have a pressure issue. You shouldn't have to pull them up. Rotators may be a possible solution but I wouln't know without flow and nozzle usage calculations. You may want to contact an irrigation professional in your area. Google reviews can help you find a good one. Or DIY study our information website at smartirrigation.com for design and nozzle selection info.
Yes, we've noticed that sometimes that happens, and there isn't really any great solution other than holding the nozzle tight in one hand and having a good screwdriver in the top and being able to turn it hard enough until it kind of breaks free from its Factory seal, and then they're easier to turn. But if you're looking at turning down your distance much, you might just want to look at a smaller nozzle, you can get them all the way down to four or five feet as the full distance through the nozzle. But good luck with turning that adjustment screw, let us know how it goes!
Yes, it should, the water usage difference is minimal so your system should have sufficient water supply, and the threads are the same, so simply screw off the 5 foot nozzle and screw on an 8-foot nozzle, and then follow the video for setting it!
Why is it that i always have trouble adjusting the distance? It seems the distance screw on my sprinkler heads, including brand new, are often stuck and i can't adjust them. Do you have any advice for that problem? Tks
Yes, we've noticed the same thing too. It might be a side effect of the manufacturing process, we're not sure. But we do find once you get the adjustments crew moving, it's easier to keep it moving. So maybe if you have a brand new nozzle, with it just in your hand, not on a sprinkler body, just hold the nozzle tight with one hand and get a good screwdriver and the adjustment screw on the other hand, and see if you can break loose that Factory seal, and then it should be easier to adjust them in the future.
I cannot figure out what my sprinkler heads are - rain bird, Hunter, there appears to be a mix (25 yr old house we bought). Control panel looks new, Hunter. I thought they were blue ringed rain bird, but the spray is sort of a half circle mover… it is not like I put my thumb over a hose -pattern. It is not like a full rotation head either (imagine our childhood tick tick tick ones). It is unique, it appears like the water in on a conveyer belt that only goes so far. Please help! I want to adjust the “throw” distance but turning that flathead screw did nothing. What type of nozzle heads do I have?
Hmm, it's hard to say without looking at them. You could take I'll look at our nozzle selection article at www.smartirrigation.com where there are a few pictures of different types of heads as well as their names, so that might help you find the right terminology to share with us. Alternatively, some of support levels on our patreon page include custom Solutions to problems where you can upload pictures and things like that and we will give you an individualized solution, if that's something you would like and would find Value in. You can check out our patreon page at www.patreon.com/SmartIrrigation. Good luck!!!
Rainbird sprays have clear and blue filter options. The blue filter is a finer mesh and used for sprays with smaller orifices, typically 10ft and lower or their he-vans. The grey screens are for all hunter sprays. If your buying new sprays, you can just use the filters they came with
Hi, you can certainly change out the fixed-pattern quarter spray nozzle to a different fixed-pattern (or adjustable patter). As per the parts of the spray shown at 1:27 in our video, just unscrew (counterclockwise) the old spray nozzle from the riser/stem, and while still holding up the riser/stem screw on (clockwise) the new spray nozzle
Thanks for watching! With a proper filter installed below the nozzle, you can turn off the spray completely by turning the distance adjustment screw on top clockwise until the water stops flowwing
Raising heads is typically done by replacing the current nipple that connects the spray body to the lateral irrigation line and putting in a longer nipple, but that all depends a bit on how the system is set up. if you would like us to do a video on that let us know in the comments!
The droplets are designed to be fine for proper distribution. They will become larger as you turn down the radius of the spray, but it will impact how even the coverage is
The ratcheting can be avoided by twisting the full sprinkler head body and removing it of the housing it is in without twisting the whole sprinkler out of the hole its in, ratcheting can break the sprinkler.
Thanks for stopping by! The ratcheting is actually part of the spray-head design for rainbird 1800 sprinklers, as is mentioned in Rainbird's own literature (www.rainbird.com/sites/default/files/media/documents/2017-06/man_sprayheads.pdf). Using this method helps with fine tuning the adjustment while the sprinkler is running, which can't be done with the removal method). Turning the body in the ground, though, also works, but can be challenging if the top of the sprinkler cap is overgrown at all.
Great video. Do you have a tip on how to loosen the dial to adjust the arc when it becomes hard to turn? Assume one can mix adjustables and none adjustables in the same zone, correct?
Thanks! Ya those rainbird adjustable nozzles can be a pain once they get tight, especially since closing them (turning counterclockwise since they are left stop) unscrews the nozzle off of the spray riser at the same time. If it's giving you trouble you can try taking it off the spray (be sure to replace with another nozzle or flush cap so you can pull the spray riser back up) and the once it's off working it back and forth multiple times. And if it is still tight, it might be time to just replace the nozzle. And yes, in general, you can mix the rainbird fixed (mpr) nozzles with their adjustable (van and he-van) nozzles since they have similar precipitation rates. But for nozzles that aren't matched precipitation rate, it's always best to check with the manufacturer literature to make sure the precipitation rates are similar Hopefully this helps!
While the correct nozzle is certainly the most important, but using the screw to fine-tune distances when they are in-between nozzle sizes (such as having to water an 11-foot radius, which is inbetween the 10-foot and 12-foot nozzle) can make an important water-saving difference.
Sir, in my opinion it's a huge mistake to "turn the stem" to adjust the pop-up to the correct position for watering. Why? I used to do this but what happens is that you will strip the plastic inside so then when the sprinkler pops-up it doesn't stay in the proper position because it's stripped inside and then tends to travel by itself either too much to the left or right. I have seen it where I'm watering my neighbors lawn and Not mine. I have a better technique: 1) The base part that's in the ground, have slightly loose, meaning turned slightly left so it's not all the way tight. 2) Put the whole top part on: (plastic tube pop-up, spring, thread, head, everything), slightly to the left also. Turn right to tighten then when the thread gets tight, you keep turning so then the BASE bottom part (that's in the ground) is now turning - so now the whole thing is turning, and then just have the head go where you want it to go.
Thanks for watching! On some older style heads (like the Hunter SRS) it used to be an issue of wearing out the ratcheting mechanism, but current rainbird 1800 heads are designed to be adjusted this way according to Rainbirds own literature (www.rainbird.com/sites/default/files/media/documents/2017-06/man_sprayheads.pdf). Turning the base in the ground can work well too though! Thanks for your input!
Thanks for watching! On the adjustable nozzles you can adjust them all the way closed and only a time stream will come out. But to further reduce the water, you can turn the distance adjustment screw clockwise until the stream basically stops (as long as a filter has been installed below the nozzle)
Liked the video? Help us make more at www.patreon.com/SmartIrrigation
Adjusting sprinkler heads is not something I do often enough to recall the nuances of adjusting them. Your video is amazingly detailed on the procedures, as well as going directly to the important points. It was highly educational, easy to follow, and a pleasure to watch. Thank you!
Glad it was helpful! That's for the support!!
Thank you! Thank you! Thank you! I have been having a devil of a time with our new sprinkler system. The installers didn't explain this much in detail, and I have two heads that are throwing too far onto bushes that are "low water required." It's been killing my bushes. Now I can reduce the throw distance of this 15ft-VAN and save my bushes! I am extremely appreciative for this educational video.
You are most welcome! I am glad our video helped! But remember the tip in the video: its always best to pick a spray nozzle of the correct distance since turning the spray down more than a few feet really messes up its watering efficiency. So if you need to turn your 15van down to 12 feet or less, its probably best to switch out the nozzle with a smaller one. Happy watering!
@@SmartIrrigation1 - Yes! Definitely noted. I measured the distance, and the sprinkler only needs to reach 12.5 feet in that area before hitting the bushes. Then I noticed that a 15ft half-circle was also spraying into the bushes at its farthest left corner. I reduced both of them and all seems to be much better! Hopefully my pittisporum bushes will get relief. I can increase the throw distance once we get to summer and the Texas heat scorches the bushes a bit too much. I'm just glad I know how to do it thanks to your video.
I'm glad! Take care and keep us posted!
This is perfect! I am a first time home owner and have no idea what I am doing with lawn care. However, this one video probably just helped save my lawn as I am having watering issues. Thank you for taking the time to break this down and explain it very simple.
Awesome! Thank you! Glad it was helpful!
yes.Nicely made video and simple explanation such that any layman can understand.superb
Very informative, concise and to the point showing how you do the actual and minor adjustments. No BS. Thank you.
Thanks for the kind words. You're very welcome!
@@SmartIrrigation1 Have you, by chance, done a similar review for Rainbird’s rotary sprinklers?
You bet! You can find it here: th-cam.com/video/9Dyv_NomGHw/w-d-xo.html
@@SmartIrrigation1 thank you. Much appreciated. 👍
Great video! With your video, I was able to adjust my sprinkler. Keep up the professional work.
Glad it helped! Thanks for watching!
I love it. I have way more knowledge about my sorinkler heads than i did before. I really appreciate your time. 😊
You're very welcome!!
This was so helpful. Best tutorial out there (and I searched far and wide)!
Wow that's awesome, thanks for the kind words!! Glad they are helpful!
Finely I have found a video showing the correct RainBird sprinkler head the builder installed. I have an adjustable head that has not been watering an area and the grass has dried up. Installed sod and now for the adjustment. Thanks for this video showing me how to properly adjust. 😊🎉
Glad this was helpful! Good luck!
Great video. I never messed around with sprinklers, and this made it very easy. Thank You !
I'm very glad this helped!! Your welcome!
Thanks! Very clear and concise instructions. Too bad Rainbird doesn't put this kind of effort into giving their customers the information they need.
You are very welcome, glad it was helpful!
Just what I was looking for to explain how sprinklers work. Thank you!
You're very welcome!
You make it look so easy. Many of my sprinklers are 28 years old, the tops are not legible, and the grass (St. Augustine) has gotten so thick, that some of them can't even pop up. I need to put risers on? Some of them won't rotate anymore. Two of them broke off from the pipe. Trying to save $ by doing it myself, it's a b___h. It's only going to be 101 today, vs 103 yesterday, I should get going while it's still cool (83). Thanks for sharing, this was a very clear, easy to see video.
Haha thanks. You can put longer nipples on the spray bodies (perhaps we'll make a video on that in the future), or switch to a larger pop-up (like a 6"). And ones that don't rotate anymore will need to wither be cleaned out or replaced. Good luck!!
Great info! The irrigation contractors in this area are overwhelmed and I’m going to tackle several issues with my older system
Thank you
You're welcome! Let us know how it goes and hopefully our videos are a bit of help!
Your videos are always outstanding. Thanks for offering this valuable information!
Wow, thanks for the kind words! Glad our videos are helpful!
You earned a sub. Thanks for explaining this so clearly.
Thanks!! And you are very welcome!!
Thanks for the advice! Preparing to redo my lawn in the fall so need my sprinklers working well, but what grass is this? I love the dark green lawn
Thanks for watching! I believe it is a cold-weather mix of Kentucky Bluegrass and Tall Fescue, likely cared for with a nitrogen rich fertilize.
Thank you for the informational yet concise video !
You bet! Glad you enjoyed it!
Great video. Simple and easy to follow. Thank you so much.
Glad it was helpful! Your welcome!
Very clear and concise. Thanks for taking the time to make this, super helpful.
I'm glad it was helpful! Thanks for watching
Excellent and extremely helpful video. Youve just saved me lots of grief.
I'm very glad! Thanks for watching!
Fabulous video! Easy, step by step tutorial - thank you - I have subscribed.
Thanks for the sub! Glad you enjoyed it!!
This is the best video I’ve seen on this topic!!! Thank you!
Wow thanks for the kind words! Glad it was helpful!
Great video! Is it possible to shut off a nozzle by turning the stem?
Thanks for watching! On the adjustable nozzles you can adjust them all the way closed and only a time stream will come out. But to further reduce the water, you can turn the distance adjustment screw clockwise until the stream basically stops (as long as a filter has been installed below the nozzle)
That is an absolutely crystal clear explanation, thanks for sharing! 👍
Thanks!! I'm glad it was helpful!
Thank you!!!! You are an EXCELLENT teacher!!!
I wish all the so-called "sprinkler repair" in my companies in my area knew this info.!!!!!
Thanks for the awesome comment and we're always glad to help!
Great video, just to the point and well explained! Thanks!
Glad you liked it, thanks!
Great video! I have a question though, my stem doesn’t seem to go up much when I turn the system on, so it’s not getting about the grass. Any recommendations? Thank you!
If the spray has a stong flow coming out of it, It would not be a pressure or flow problem. In that case you probably have a head that is two low (deep) in the ground or it is a 2 inch popup or similar but in either case you would need the head, raised and replaced, or replaced if the head is just a short 2 inch.
@@SmartIrrigation1 Thanks so much, I appreciate your answer!
Quick question I just had a sprinkler system installed a month ago and we have the fixed rain birds up along our house, but unfortunately, when the landscapers put them in, they also tied those to a side yard with grass so if I go lower on the amount of time I run them the grass gets less what I am trying to do is Have less water come out along the fixed ones in front of our house has bushes and rosebushes and other things
By turning the screw clockwise, you describe in the video that it takes the pattern smaller is that also having less water come out of them?
Thank you, sir
Thanks for watching! The distance adjustment on these sprays doesn't have a well-defined impact on precipitation rate (how much water is put down per minute); ideally you only use the screw to make a small 1-foot adjustment and that would have a negligible impact on the amount of water given. What you want to do is look for different spray nozzles that have different precipitation rates. One example would be to put in rotary nozzles in areas that need less water and keep the spray nozzles in the area that needs more water. Let us know how this works out for you!
Perfect. This helped me out, just what I needed.
I'm really glad this helped! Thanks for letting us know!
Thank you so much for the detailed explanation!
You bet!! Thanks!
Thank you for sharing it. Great information.
You bet! Glad it was helpful!
Thanks, extremely clear and concise!
Thank you very much for the kind words!
Liked the video? Help us make more at www.patreon.com/SmartIrrigation
Awesome video! Very detailed and just what I needed.
Thanks for the kind words, I'm glad it helped!
Your explanation honestly makes it easy, so I subscribed. But I do have a question: I have no idea what brand of Sprinkler Rotors were put into the 2 zones about 7 years ago, but they do work. Can I use a Rainbird stationary nozzle on a Hunter Rotor shaft pop-up, or a Hunter stationary nozzle on a Rainbird Rotor shaft pop-up? I watched a video that said both Rainbird and Hunter use professional grade female thread pop-ups and nozzles.
Yes , brands of nozzels are interchangable on differing brands heads. This allows us to choose the best nozzel for the area to be covered regardless of brand. Check out our article on nozzel selection at smartirrigation.com if you like for some more info in this.
Thank you for the quick reply, I'm learning as I go here. Much appreciated!!@@SmartIrrigation1
Excellent video and explanation! Thank you!
Thanks for the kind words, I'm glad you found it helpful!
Good informational video
Thanks! Glad you found it informative!
This is the best explanation, thank you!
You're very welcome!
How about the height? I'd like my grass to be a little higher during the hot summer but my nozzles end up hitting the grass blades closest to the head eliminating spray further out. I can pull them up by hand high enough but they don't stay
Sounds like you have a pressure issue. You shouldn't have to pull them up. Rotators may be a possible solution but I wouln't know without flow and nozzle usage calculations. You may want to contact an irrigation professional in your area. Google reviews can help you find a good one. Or DIY study our information website at smartirrigation.com for design and nozzle selection info.
These videos are the best!! Thank you!
You're so welcome!
Any suggestions for getting the distance screws to turn? Brand new nozzles and none of the screws will turn.
Yes, we've noticed that sometimes that happens, and there isn't really any great solution other than holding the nozzle tight in one hand and having a good screwdriver in the top and being able to turn it hard enough until it kind of breaks free from its Factory seal, and then they're easier to turn. But if you're looking at turning down your distance much, you might just want to look at a smaller nozzle, you can get them all the way down to four or five feet as the full distance through the nozzle. But good luck with turning that adjustment screw, let us know how it goes!
Great video. Thanks it was very helpful.
I'm really glad it was helpful! Thanks!
Thanks. If I change my nozzle from 5 feet to 8 feet will it work on existing sprinkler
Yes, it should, the water usage difference is minimal so your system should have sufficient water supply, and the threads are the same, so simply screw off the 5 foot nozzle and screw on an 8-foot nozzle, and then follow the video for setting it!
Great video , thanks for your information , definitely a helpful video , very well explained 👍👍
Glad it was helpful!
Thank you for this great video, helps me a lot.🌊
Wow thanks for your support!!! I'm very glad it helped you!!
great video, very informative, thank you!
Thanks for the kind words! Glad you like it!
Well done! 👏
Thanks! Glad you liked it!
Wow, very helpful!❤
Glad the video was helpful to you!
Great video!!
Thanks, we hope to do more like this!
Why is it that i always have trouble adjusting the distance? It seems the distance screw on my sprinkler heads, including brand new, are often stuck and i can't adjust them. Do you have any advice for that problem? Tks
Yes, we've noticed the same thing too. It might be a side effect of the manufacturing process, we're not sure. But we do find once you get the adjustments crew moving, it's easier to keep it moving. So maybe if you have a brand new nozzle, with it just in your hand, not on a sprinkler body, just hold the nozzle tight with one hand and get a good screwdriver and the adjustment screw on the other hand, and see if you can break loose that Factory seal, and then it should be easier to adjust them in the future.
@@SmartIrrigation1 Thanks for the advice. I'll try removing the nozzles and adjusting them.
I cannot figure out what my sprinkler heads are - rain bird, Hunter, there appears to be a mix (25 yr old house we bought). Control panel looks new, Hunter. I thought they were blue ringed rain bird, but the spray is sort of a half circle mover… it is not like I put my thumb over a hose -pattern. It is not like a full rotation head either (imagine our childhood tick tick tick ones). It is unique, it appears like the water in on a conveyer belt that only goes so far. Please help! I want to adjust the “throw” distance but turning that flathead screw did nothing. What type of nozzle heads do I have?
Hmm, it's hard to say without looking at them. You could take I'll look at our nozzle selection article at www.smartirrigation.com where there are a few pictures of different types of heads as well as their names, so that might help you find the right terminology to share with us. Alternatively, some of support levels on our patreon page include custom Solutions to problems where you can upload pictures and things like that and we will give you an individualized solution, if that's something you would like and would find Value in. You can check out our patreon page at www.patreon.com/SmartIrrigation. Good luck!!!
How do I know what filter each spray head needs? I’ve seen clear, blue and even grey filters is there a difference ?
Rainbird sprays have clear and blue filter options. The blue filter is a finer mesh and used for sprays with smaller orifices, typically 10ft and lower or their he-vans. The grey screens are for all hunter sprays. If your buying new sprays, you can just use the filters they came with
This video is fantastic!!! Thank you👍😇
Thanks so much! Glad you like it!
Very informative! Thanks.
Glad it was helpful!
Incredible video. Thank you
You are very welcome!
Explained perfectly
Thanks! Glad it helped!!
beautifully shot video
Thanks!!
I have a quarter pattern. Can I just change out the riser for a 360 riser insert?
Hi, you can certainly change out the fixed-pattern quarter spray nozzle to a different fixed-pattern (or adjustable patter). As per the parts of the spray shown at 1:27 in our video, just unscrew (counterclockwise) the old spray nozzle from the riser/stem, and while still holding up the riser/stem screw on (clockwise) the new spray nozzle
Thank you, great vid.
Your welcome! Glad you liked it!
How do I shut off the spray completely?
Thanks for watching! With a proper filter installed below the nozzle, you can turn off the spray completely by turning the distance adjustment screw on top clockwise until the water stops flowwing
Very good video 👍🏻👍🏻👍🏻
Thank you so much 👍
Thank you. Very valuable information.
Glad it was helpful!
Thank you so much! Very very helpful.
You're very welcome!
Thank you for sharing you knowledge
Absolutley!
Fantastic video, thanks!
Glad you liked it! Thanks!!
How do you raise your head ?
Raising heads is typically done by replacing the current nipple that connects the spray body to the lateral irrigation line and putting in a longer nipple, but that all depends a bit on how the system is set up. if you would like us to do a video on that let us know in the comments!
Very helpful - thank you.
Glad it was helpful!
Outstanding videos.
Thank you very much!
Outstanding! Thank you!
You're very welcome!
Thank you sir for you knowledge
You are most welcome! Thanks for watching!
that's some nice grass
Sph you like that you should check out my beautiful crabgrass
😄
Nice video,subbed!
Thanks!!
Very helpful!!
Thanks!
Very professional
Thanks!!!
Thank you very much!
You are most welcome!
Super helpful.
Thanks!!
Why is it leaking under blue colored ring, Is it broken? ( the arc one)
You're right, the leak is not part of any design, it is just the defect any of the spray body or the nozzle that we used. Sorry for the confusion haha
Thank you, Sir!
You are most certainly welcome!
Perfect video
Thanks, glad it helped!
how can i make my droplets heavy and thick instead of so fine ?
The droplets are designed to be fine for proper distribution. They will become larger as you turn down the radius of the spray, but it will impact how even the coverage is
turn down the radius of the spray. What does that mean ? How would I do that ?
If you watch our video, we show you how to do it at 3:12 in the video 😁
Agree. Good video
Thanks!!
The ratcheting can be avoided by twisting the full sprinkler head body and removing it of the housing it is in without twisting the whole sprinkler out of the hole its in, ratcheting can break the sprinkler.
Thanks for stopping by! The ratcheting is actually part of the spray-head design for rainbird 1800 sprinklers, as is mentioned in Rainbird's own literature (www.rainbird.com/sites/default/files/media/documents/2017-06/man_sprayheads.pdf). Using this method helps with fine tuning the adjustment while the sprinkler is running, which can't be done with the removal method). Turning the body in the ground, though, also works, but can be challenging if the top of the sprinkler cap is overgrown at all.
Great video. Do you have a tip on how to loosen the dial to adjust the arc when it becomes hard to turn? Assume one can mix adjustables and none adjustables in the same zone, correct?
Thanks! Ya those rainbird adjustable nozzles can be a pain once they get tight, especially since closing them (turning counterclockwise since they are left stop) unscrews the nozzle off of the spray riser at the same time.
If it's giving you trouble you can try taking it off the spray (be sure to replace with another nozzle or flush cap so you can pull the spray riser back up) and the once it's off working it back and forth multiple times. And if it is still tight, it might be time to just replace the nozzle.
And yes, in general, you can mix the rainbird fixed (mpr) nozzles with their adjustable (van and he-van) nozzles since they have similar precipitation rates. But for nozzles that aren't matched precipitation rate, it's always best to check with the manufacturer literature to make sure the precipitation rates are similar
Hopefully this helps!
Thank you so much.
You are most welcome!!
Awesome....thank you
You are welcome!
Use the screw as on and off only. Use appropriate nozzle.
While the correct nozzle is certainly the most important, but using the screw to fine-tune distances when they are in-between nozzle sizes (such as having to water an 11-foot radius, which is inbetween the 10-foot and 12-foot nozzle) can make an important water-saving difference.
Thanks!
You bet!! Thanks for the support!!
👍
Thanks!
Thank you.
You are most welcome! We hope you enjoy!
thanks!
You're welcome!
Don't they have rotary nozzles too
Yes they do. We have a setting tutorial and article on them also at smartirrigation.com
Sir, in my opinion it's a huge mistake to "turn the stem" to adjust the pop-up to the correct position for watering.
Why?
I used to do this but what happens is that you will strip the plastic inside so then when the sprinkler pops-up it doesn't stay in the proper position because it's stripped inside and then tends to travel by itself either too much to the left or right.
I have seen it where I'm watering my neighbors lawn and Not mine.
I have a better technique:
1) The base part that's in the ground, have slightly loose, meaning turned slightly left so it's not all the way tight.
2) Put the whole top part on: (plastic tube pop-up, spring, thread, head, everything), slightly to the left also. Turn right to tighten then when the thread gets tight, you keep turning so then the BASE bottom part (that's in the ground) is now turning - so now the whole thing is turning, and then just have the head go where you want it to go.
Thanks for watching! On some older style heads (like the Hunter SRS) it used to be an issue of wearing out the ratcheting mechanism, but current rainbird 1800 heads are designed to be adjusted this way according to Rainbirds own literature (www.rainbird.com/sites/default/files/media/documents/2017-06/man_sprayheads.pdf). Turning the base in the ground can work well too though! Thanks for your input!
I found a water bird on my holiday
😁
FBI.
Holland.
Probaby Kelsey Green
of St Petersburg, FL.
#2
? What is this about?
Great video! Is it possible to shut off a nozzle by turning the stem?
Thanks for watching! On the adjustable nozzles you can adjust them all the way closed and only a time stream will come out. But to further reduce the water, you can turn the distance adjustment screw clockwise until the stream basically stops (as long as a filter has been installed below the nozzle)
Thanks!
Wow awesome thanks for the support!!