Whirlpool Top Load Washer Replace Shift Actuator
ฝัง
- เผยแพร่เมื่อ 5 ก.ย. 2024
- This video provides step-by-step repair instructions for replacing the shift actuator on a Whirlpool washer. The most common reason for replacing the shift actuator is if the washer isn’t cycling properly.
Buy part #W10597177:
www.repairclini...
Learn how to troubleshoot your washing machine:
www.repairclini...
This shift actuator replacement video is applicable to the following brands:
Whirlpool, Amana, Crosley, Inglis, Kenmore, Maytag, Roper
Tools needed: 5/16th inch socket or nut driver, Phillips-head screwdriver
Connect With Us!
plus.google.co...
/ repairclinic
/ repairclinic
/ repairclinic
Join our VIP email list for discounts and money-saving tips: tinyurl.com/pnn...
Check out our blog: www.DIY.RepairC...
Don't forget to like and comment on this video, and subscribe to our channel!
After changing the part - is there some calibration or anything needed to be done? Or just replace and go?
Dont take my word for it but in the manual it doesnt say calibration is needed if this is the only part you replaced.
I have a Whirlpool Washing Machine Model WTW4815EW1, top loader. During the agitation cycle I could hear a rhythmic clicking noise. I researched and found that the splutch may be the problem. I ordered the kit and did the job this morning. As I got the washer out of it's spce and laid it over I found a piece of place broken. As I looked closely at the mechanism it became obvious that the shift actuator arm had broken off of the actuator. I replaced the splutch kit assembly because I already had it on hand. I ordered the new actuator and it will arrive in a couple of days. Neither part is overly expensive and replacing them is mildly mechanical. I bet my wife will notice that the clothes are cleaner once they now get agitated through their cycle.
Yeah, yeah... I know. If I had bypassed the lid lock I would have readily noticed that the agitator wasn't agitating. So no need to pile on super-techs.
what about calibration?
I have to replace actuator twice. Why does the shift actuator plastic arm keeps breaking?
Is there a way to bypass the lid lock on the newer washers? I tried a few possibilities with no luck. It seems that the brain box needs to see the lid cycled open and closed before it will start.
So i bought two shift actuators now from amazon. the first one lasted for 5 cleans then the second lasted 1. i made sure the lever it has to turn isnt jammed up and moves nice and easy. waiting on the third one now but do you think im receiving junk actuators or whats going on here? Why does it keep going thru them? any ideas id appeciate. Hate to have to buy a whole new washer now over a 30 dollar part
almost as if by design...
Thanks a lot I learnt it this is Avery good technical school even though it's not a school but thanks again
You're welcome!
We are always happy to help. If you would like to give us a review on Google, we would much appreciate it: g.page/r/CcVUrahZNozMEBM/review
We hope that you have a great day!
Thank you for the repair tutorial!
I change 3 dam parts and it still show sensing error, even whit water on it wont pump the water in
You should do a diagnostic test in your washer so that you can get the exact code of what parts you need to change or repair. Read the manual it's in there.
The manual for running diagnostics is taped to the inside of the front of the washer. You need to lift the top to get at it.
Its the shift actuador bad & need to change?
My washer shift actuator keeps going out, replace it twice after a week it goes out again.....any idea what could be causing it. I have a Whirlpool WTW4816FW2.
I just did this and found oil around the belt guard. What could cause this? We just changed every piece of equipment. What could cause the motor to leak?
Usually a bad gear case
Should the shift motor have resistance? My new part doesn't read any similar to the old part. Wondering if I received a bad part.
What happens if your machine actuator moves and machine cycles very slow
How do I know for sure this is what I need? My washer won’t agitate or wash. It just makes a noise every other second during those cycles and then drains, rinses, and spins out.
I bet you its exactly what it needed. Mine is broken now and I'm waiting for the part to come in. Did you get yours fixed?
Same question, did this fix you up?
Is there a master reset that can be done?
I have kenmore 500 series and maytag centennial they both stop on rinse,rinse light flashing what will cause of that? Needs help pls...do you think I have a bad shift actuator too?
Good job
What does an actuator cost
Must be nice to have a brand new model to show this with. In reality that guard is covered in rubber pieces
My 15kg whirlpool washing machine only full but not going to self wash. What is the problem
LId stuck, light blinking, washer will not engage anything. Green light in control, all lights function on front of top. Turn washer on set at normal, push the start on the Cabrio and red light flashing but no noise for the interlock. New interlock and catch installed. What now? Is it the actuator or what?
Same problem, same process: replaced lid lock system, replaced the capacitor. Still not working. Called repairman, he gave me all kinds of "assumptions" even replaced a actuator he had in his bag, still not working. He even could not put the back panel back (wonder why he took the panel off in the first place). He still asked for the initial visit charge. I refused. The only thing I learned is that this is not an actuator problem. Now what? Need help.
@@tatianefernandes800 I got replies that it was the control board from techs. Now, why does it work in automatic test and manual test but not when i push the start button on NORMAL wash? Or any of the wash cycles normally? I know the lid light blinks and will not engage the "lock" because it will not start at all. I think something in the sensing circuit is to blame as it requires knowledge from the start button to send a message to the motor and to the water inlet valves to fill up. Once filled up the washer lid should lock and start to agitate but if it will not even start to fill in normal mode then why does it work in all the test modes? Where is the culprit in the circuit? i cannot get a find on the circuit board showing a trace route from the start button engaging the circuit route to make the other parts interact. If i had a color diagram of the sequence of events from starting then i could isolate the part that is not communicating with the rest of the circuit. I am not sure if anyone can do this in America.
sounds like a board, usually the last thing you wanna go for but sometimes when there's no other reasonable explanation, it's a faulty board
@@tatianefernandes800now pay the guy haha jk
Fix Whirlpool machine spring
If Whirlpool wouldn't build their machines out of junk plastic, this would not happen so often.
but then they wouldn't sell so many machines