As DIY spray pump they are very good I've got the 250r and have put at least 1000 litres through it in roughly 4 years and it still sprays absolutely fine but I do look after it I clean it properly after every use I cycle the pump with warm soapy water until it runs clear then cold flush put pump armour in it and strip the gun down for what they cost which isn't a lot in comparison to other units what mine has done is quite amazing really considering oh and just a tip for anyone who buys one of these units before every use take the suction tube off and put a few drops of piston lube in and push the red ball release button a few times and let it sit for 10 minutes if you do that the little pump will work it knackers off all day with no issues at all
You say piston lube in the suction hose. Do you mean once removed put few drops directly into the machine via the suction hose port? Also the pump armour. You add that to the machine once its fully clean i.e prime the machine with it and atore it away.Any help would appreciate it 👍
@Imran Khan yes turn the unit upside down put a few drops of piston lube in and let it sit do this every time you use it before you do anything else hope this helps
Followed your instructions to prep, spray, and clean, and I gotta say everything went so smoothly. The way you clearly described the methods and steps is so helpful. Got 4 large rooms done today using the 350M with no problems. Even cleaning was quite easy. Thanks again
Hello, I have now tested three different colors. The paint manufacturers recommends a maximum of 10 percent water. I only get a good picture if I dilute more than 20 percent with water. does anyone else have the same problem?
Hi, I need some advise please, I am a painter but have never used a sprayer before. I purchased the 150 m but found it ran out of paint to quickly and the cleaning was a bit of a drag. I have returned it and looking to get another one. I do mostly residential work ( living rooms, hall stairs and landings) and ideally would like not to thin the emulation down, i would be using it for doing mist coats quite a lot. should I get the 250 m or 350 m or Maybe a different brand maybe Graco.
I am struggling to change the filter... can you explain... I am trying to unscrew filter housing unscrew so it is in two from the middle it just won't budge.
Great video. Ive had the 350 skid for a few years doing small to medium diy jobs. A highly recommended bit of jit I would also recommend cleaning the gun filter out every time.
The only thing that was said was that jobs never take just one day. So do you need to clean this at the day of each day. Or can the paint stay in the hose over night ready to continue the next day?
Hi guys would really appreciate some help I’ve recently bought a 250m airless paint pro sprayer assembly was fine I’ve the 517 tip and I’m having serious trouble with the tip clogging , I can only get 5seconds out of gun before tip gets clogged I’ve tried every method I could find online , cleaning it all out, back spraying , using setting powers from 1-5 but it keep happening I’m using brand new exterior weather shield wall paint as I’m painting my garden wall , can someone please help me with this matter as I’ve paid over €550 for the machine and it’s infuriating that I’m having this problem from the get go , would really appreciate any help
I bought is 11 march and used it today what a crap. The gun trigger is not pressed in and the paint still coming out and it loses its pressure while spraying primer latex 15% with water. I always spray that same product with graco totally bo problems
Can you buy a small nozzle,for the 250M to spray Dulux satinwood diamond white water based(high viscosity) ,for woodwork that gives a 4" spray without having to overthin the paint.Any ideas??
A graco FFLP 208 tip will do for the satinwood you need to get a rac x tip guard they only fit the tips they atomise at about 900psi and are best for woodwork pit a red gun filter in otherwise you will get stoppages all the time use the tip seat that comes with the tip and let the paint down about 15% and you should be good to go hope this helps
@@johnthemod71 Ah good, thanks for confirming. I'm a carpenter so want it to spray up skirting, architraves, etc however it would be really useful painting walls of extensions etc. Sounds like the machine for the job.
@@kevocos absolutely but remember cleaning it out properly is just as important as using it and always always thin and strain your paint first for it to atomise and spray nicely
I have the 350 but is really giving me problems..it never spray airless ..when I spray it the edges are very thick and makes a line…I have tried everything..is there way way u can help me solve this problem?
As DIY spray pump they are very good I've got the 250r and have put at least 1000 litres through it in roughly 4 years and it still sprays absolutely fine but I do look after it I clean it properly after every use I cycle the pump with warm soapy water until it runs clear then cold flush put pump armour in it and strip the gun down for what they cost which isn't a lot in comparison to other units what mine has done is quite amazing really considering oh and just a tip for anyone who buys one of these units before every use take the suction tube off and put a few drops of piston lube in and push the red ball release button a few times and let it sit for 10 minutes if you do that the little pump will work it knackers off all day with no issues at all
You say piston lube in the suction hose. Do you mean once removed put few drops directly into the machine via the suction hose port? Also the pump armour. You add that to the machine once its fully clean i.e prime the machine with it and atore it away.Any help would appreciate it 👍
@Imran Khan yes turn the unit upside down put a few drops of piston lube in and let it sit do this every time you use it before you do anything else hope this helps
ImranKhan-K11A17
Followed your instructions to prep, spray, and clean, and I gotta say everything went so smoothly.
The way you clearly described the methods and steps is so helpful.
Got 4 large rooms done today using the 350M with no problems. Even cleaning was quite easy.
Thanks again
Excellent and clear instructions how to clean the paint
Do you have to water down your paint at all please x
Thanks for a good video. Can you use the 350m outdoors? For ex. Panting the walls on a house? I only got that you mention indoor use.
Are they both good for a house with round about 750 square meters of walls and cieling?
Would you be able to to spray masonry paint with the 350m ?
Thank you !
Thank you. Great video
Thanks for a great video. Which is better? The 250 M or the Graco 16w120. Thanks
Hello, I have now tested three different colors. The paint manufacturers recommends a maximum of 10 percent water. I only get a good picture if I dilute more than 20 percent with water. does anyone else have the same problem?
Hi, I need some advise please, I am a painter but have never used a sprayer before. I purchased the 150 m but found it ran out of paint to quickly and the cleaning was a bit of a drag. I have returned it and looking to get another one. I do mostly residential work ( living rooms, hall stairs and landings) and ideally would like not to thin the emulation down, i would be using it for doing mist coats quite a lot. should I get the 250 m or 350 m or Maybe a different brand maybe Graco.
I am struggling to change the filter... can you explain... I am trying to unscrew filter housing unscrew so it is in two from the middle it just won't budge.
Great video. Ive had the 350 skid for a few years doing small to medium diy jobs. A highly recommended bit of jit
I would also recommend cleaning the gun filter out every time.
The only thing that was said was that jobs never take just one day. So do you need to clean this at the day of each day. Or can the paint stay in the hose over night ready to continue the next day?
This is all well and good if you’re whitewashing everything, but what if you want to apply a dark wall colour and white ceilings.
What's the difference between the M' and the R' models? I can't seem to find any difference betwween the 250M and the 250 R etc. TYIA
The M(etal) has a metal frame around the pump unit whereas the R(esin) uses plastic. Just a durability difference
Welcome back old friend
Hi guys would really appreciate some help I’ve recently bought a 250m airless paint pro sprayer assembly was fine I’ve the 517 tip and I’m having serious trouble with the tip clogging , I can only get 5seconds out of gun before tip gets clogged I’ve tried every method I could find online , cleaning it all out, back spraying , using setting powers from 1-5 but it keep happening I’m using brand new exterior weather shield wall paint as I’m painting my garden wall , can someone please help me with this matter as I’ve paid over €550 for the machine and it’s infuriating that I’m having this problem from the get go , would really appreciate any help
Did you manage to sort this issue? I’m having the same problem with my 350R now
I bought is 11 march and used it today what a crap. The gun trigger is not pressed in and the paint still coming out and it loses its pressure while spraying primer latex 15% with water. I always spray that same product with graco totally bo problems
Can you buy a small nozzle,for the 250M to spray Dulux satinwood diamond white water based(high viscosity) ,for woodwork that gives a 4" spray without having to overthin the paint.Any ideas??
A graco FFLP 208 tip will do for the satinwood you need to get a rac x tip guard they only fit the tips they atomise at about 900psi and are best for woodwork pit a red gun filter in otherwise you will get stoppages all the time use the tip seat that comes with the tip and let the paint down about 15% and you should be good to go hope this helps
@@johnthemod71 so it sounds like these wagners are suitable for painting woodwork then? I'm struggling to find a confirmed answer to this.
@@kevocos yes they are absolutely fine for spraying woodwork I have used mine for it
@@johnthemod71 Ah good, thanks for confirming.
I'm a carpenter so want it to spray up skirting, architraves, etc however it would be really useful painting walls of extensions etc.
Sounds like the machine for the job.
@@kevocos absolutely but remember cleaning it out properly is just as important as using it and always always thin and strain your paint first for it to atomise and spray nicely
I have the 350 but is really giving me problems..it never spray airless ..when I spray it the edges are very thick and makes a line…I have tried everything..is there way way u can help me solve this problem?
I read a comment on another video that you need to increase the pressure
And dilute your paint with water a bit more
Why do companies put on videos and then ignore all comments.
In many cases you are ignoring customers, madness