Jaw Crusher Hammer crush plant Machine Bearing Replacement processes || with limited tools

Jaw Crusher Hammer crush plant Machine has Broken the Old bearings ||new bearings installed it place
#bearings earings
#crushplantmachine
#jawcrusher
#hammer
#pakistanitrucks
#excavatorworking
#discoveringskills
#amazingskills

[@z400racerr910]

So much sand in the bearings lol, they also took all the grease out and put none in after lighting a fire inside. Dry bearings with sand and no grease? Hmmm

[@maximtem6717]

стерильность рабочего места (как и всего остального)-просто зашкаливает! и при этом, они ещё очень смешно пищат!

[@alro2434]

Nice job. Bearings that big can cope with a minimum amount of dirt, so try a little better to keep it down.

[@dustysherrmann4427]

What a difficult job and they did it.
Good men respect 👍

[@giovannifinievoli8825]

mission impossible! great yob

[@geowallace9758]

Unbelievable even the parts put back are filthy and new bearings battered in with sledge hammers., the mind boggles.

[@Amazingskills838]

Sir i have no equipment next time try to best thanks for appreciating

[@stevenhorne5089]

@@Amazingskills838 You rolled the bearings in the dirt and then didn't even attempt to pack them with grease. How much equipment do you need, to not roll the bearings in the dirt before installing them?

[@user-yo3ri6vc6w]

В не походящих условиях это колосальный труд молодцы ребята👍дай Аллах вам здоровья!

[@johndennis468]

Hard work with little tools needed to grease the bearings check bearings clearances and use a locking ring to keep the WN nut from backing off

[@giggling_boatswain]

5:02 That's why you can't put the wheel on a dry shaft. Use graphite grease and the next repairmen will thank you. I think this is a do-it-yourself repair. I don’t see any special equipment for fast work - so this is not a service. Bearings to heat so it is unacceptable. When heated above 500 degrees, a violation of the structure of the steel occurs and it will no longer be hard and strong (the reverse process of hardening). Bearings should be heated in an oil bath. They shortened the life of the new bearing with their own hands.

[@w203benz]

а где новая смазка? или я что-то пропустил?

[@thinkforyourself2109]

Didn't see them put grease back in the axle cavity. I assume they did though.

[@user-nw4nu8mf1b]

Я сам не работаю с механизмами, но на 10й секунде просмотра осады шкива подумал про домкрат. Наконец и они догадались, но вместо того чтобы двумя домкратами тупо выдавить шкив продолжили колотить его своим пакистанским Грондом... Что сказать, пацаны явно угорели по таранам, своя атмосфера у них)

[@zloi_zapax]

За такой ремонт головы оторвать. Тоесть подшипники можно просто помыть и наждачкой пройтись и можно снова в работу. Столько дрочки чтобы отмыть подшипники и поставить на место

[@luc_xott]

They sound like jawas lmao 🤣

[@juanduarte9723]

Lo que no entiendo.siendo profesionales por qué todo lo hacen al FBI mexicano ( fuerza bruta indígena ) ni una herramienta eléctrica ni neumática mis respetos

[@achijamir3882]

Perfect..

[@mikespain8655]

This will wear you out just watching.

[@ZeeshanYaranaMandokhel]

Nice 👍

[@LongHaulTrucker4Life]

Sanctuary!! Sanctuary!!

[@nandofigueira2005]

I thought they would change the bearings, it's not a good idea to clean them and then mount them, they must have a lot of wear.

[@butong-ongbut457]

Thợ ấn độ chuẩn tay nghề cao

[@tjahyosubekti6519]

Do they replace the new big bearing? How much do we have to pay for the such services? Bravo

[@Amazingskills838]

0nly $500

[@tjahyosubekti6519]

Very good job. Bravo

[@Peter-le3ux]

Sehr fleißig 👏👏👏🇩🇪

[@davidbross6942]

What was the point of the "chipmunk" sounds?

[@brahimhakim5780]

all thing is wrong in desassembling as in assembling (please use the correct tools )

[@yesukumarcbz6099]

Yes You r correct. Lot of Hydraulic Tools r available in market for Disassembling.

[@joedebosco3047]

Much respect to these gents. I have an inquisitive question: They took out buckets of grease from the inside of this behemoth, and as seen in disassembly cleaned off much grease from those huge bearings. Why was it assembled and finished dry?

[@steve4073]

if you look at the last part of the video 22.28 you will see the massive grease nipple that would be used to pump grease inside the middle of the shaft i thought same thing and wondered where the grease nipple was. hardly what you could call a nipple its huge lol.

[@yesukumarcbz6099]

After The Jaw inserting in crusher body applying grease because if grease applied now increases jaw weight and difficult to moving when inserting into crusher body.

[@silyukov]

конеш вдшкой не пшикнули вот и не идет шкив

[@BorisOsipov]

По-прежнему пренебрежение техникой безопасности. По-прежнему низкий уровень материальной культуры. Бедность...

[@user-ix7di1mw6q]

應該將一條長鑼繇將啤令迫入去，而不是用鎚打入去❤太粗瀑

[@meet141]

Which machine are they repairing

[@yesukumarcbz6099]

It is a part Stone Crusher which is called Moving Jaw

[@user-lv3tl4nb9g]

Triller !

[@gustavogaldino3968]

Parece os Minions falando

[@mohammedamanuddin980]

Halla ki kamai. ..

[@mandalh9574]

Villages work not a systematic work

[@josegoulart3756]

Brasil🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷

[@Amazingskills838]

Thanks for appreciating please alway support me

[@user-fn7fq1ui3k]

Странный ремонт!

[@50_k_o_p_e_e_k50]

Колокол !!!!

[@user-je7ck2yo1t]

Mcp4

[@johnwelch461]

WD 40 please someone

[@dudley5658]

Steel toe shoes my a$$.

[@nemovitdonbass9707]

Для чего эта машина предназначена? Это какой-то узел от ещё более огромной машины? Что это?
А вообще, народ - супер! Не боятся никакой работы, делают одними руками и примитивными инструментами невозможные работы. Чего удивляться, что у них есть ядерное оружие. И сделали они его, наверняка, в таких же примитивных условиях. Захотят и через месяц сделают в этих гаражах ракету на Марс. А все будут писать в каментах, что песок в сопло попал, да вторую ступень ракеты не так прогрели, но ракета в это время будет садиться на Марсе. 😂