Your videos helping me very much so far since I got my gx 2018 last Oct. Thank you Bob. Just 1 thing is remote control can't open automatic when I am outside around the car!!
If you have the 2014 and up, your car should be able to open up automatically once you pull on the door handles. It only works if you pull on the door handles and doesn't open if you're just in the perimeter of the car.
Right behind your front tires runs a thick black steel cross beam that runs side to side that attaches your left and right side frame beams. I normally use that intersection.
I saw this video a couple of years ago. I want to ask you why you don't include the spare tire in your rotation. Or do you? I haven't put the spare in rotation but should I?
When I bought the truck, all 4 tires were brand new. The spare was worn. I can not put the spare tire into the rotation because of this. Your truck will veer to one Side while driving. Another reason is because I replace my tires in pairs of I get a flat. If the front driver side goes flat then I replace both driver and passenger regardless if the passenger is still good. I want even wear per axle.
@@GXBOB Do you think I should just keep my spare and not put it in rotation? My GX was new when bought, it now has 20k miles. It seems like a PIA to keep changing spare every 5k miles lol
I was literally planning on asking to do a video on how to lift the car properly and where to position the jack stands. This is very helpful...btw, how many ton are you using for the floor jack.
Sorry to say but its a 2 ton and was originally purchased for my Honda Civic daily driver. I will be purchasing the low profile aluminum 3 ton from harbor freight very soon.
if i change out all 4 then usually i skip the wheel alignment but most folks recommend it to get the full life use of your treads. I typically get a set of tires on the same axle removed and replaced at the same time so yeah i get an alignment for scenarios like that. 4 = no, less than 4 = yes
Hi bob! Thanks for you vids. Prado here. Gonna do this rotation when changing rear pads and discs. Also do you considering getting 12.3 inch android multimedia upgrade for your gx? I ordered same multimedia that looks like 2022 multimedia from gx 460 but for my 2015 prado. It also changes climate control vents position like in newer models.
I haven't switched out my head unit because i haven't found anything i'm willing to spend that kind of money for, especially if its coming from Alibaba or something. I would totally test one out if a company threw me a head unit my direction.
@@GXBOB Yeah prices for head units on gx 460 versions are almost doubled compared to prado considering these units have same specs and harware. I paid 550$ for 128gb 6gb ram model with almost everything they had except 360 camera version that i dont need. I will update on its quality when i get in hands and installed.
My best assumption , yes. As there ate no other instructions out there from the dealer or manufacturer that states otherwise. I have not heard from Amy forum that this is even an issue
nope, its a 2 ton originally purchased to work on my honda civic. It's time to replace it with something else. I've had it for a long time now. Here is the link to the floor jack i currently have. 2 ton low profile rapid pump. th-cam.com/video/tdC-aswR2hk/w-d-xo.html
@@GXBOB good to know, I currently have a 2 ton low profile still in very good shape. I guess i can keep using it on the GX until it brakes. What kind of jack are you getting next?
@@bb5op585 I’m looking for any floor jacks that have quick pump features. Because our trucks are so high up in the air as it is, i don’t want a lot of pumps just so my foot jack hits the vehicle frames. Also I’m mostly likely consider long reach one too. I believe harbor has both those options in one for jack model. www.harborfreight.com/3-ton-long-reach-low-profile-professional-rapid-pump-floor-jack-black-64781.html
I wouldn't. My driveway also has a slope, but it's also wide enough for me to park sideways near the top where it's more flat & level so I can safely jack up my vehicle. If you can't do that I would strongly advise bringing it down to street level and doing it there.
depends on how much of an incline that slope is. Mine is very minimal. I put mine on jackstands all the time with parking blocks and e-brakes on. It works as long as the slope is slight.
Duuuuuude. WTF. Your impact gun is used to drive your nuts into the wheel at a medium pace. Then the torque wrench takes over. My question is are you sure all 5 lugnuts are identical? If they're not OEM, then you may have a mixture of deep and shallow lug nuts (cars vs suv wheels). Second, how is that possible if you drove all your lug nuts in at the same time slowly so they all seat equally? Third, are you sure the holes in the wheel is centered with the stud? I would take them back out and VISUALLY recenter the wheel without relying on tightening my lug nuts to align my wheels on. Good luck man. I'm sure there is a simple fix to what you just did.
@@GXBOB I didn't just do it. And it has been repeated more than once by other people (besides myself). Maybe it is a different lug nut? I don't think so, but I'll figure it out......
@@GXBOB I get rotations/balances at Discount Tire Company. I do 'other stuff' by myself, which includes removing tires for different jobs. The tech at Discount Tire gave me the wrong lug nut and they replaced it. Freaked me out - I though that I did it somehow. Problem solved!!! I forgot to update you......
3 ton would be very small for this truck, you can probably put on the rear under the diff, but I would definitely recommend 6 ton jack stand or probably long reach 3 ton might work if you can find one!
at 76ft lbs, your wheels will wobble all the way to walmart for a new set of tires. www.sparkyexpress.ca/blogs/autoverse/lexus-wheel-lug-nut-torque-chart
Couldnt figure out if I had to remove the skid in order to jackup the truck using that center point. Once again you came through, thx Bob
I always enjoy your videos Bob. The entertainment value and your sense of humor keeps me watching/liking. Thank you sir!!
Sorry to disappoint but my later videos are not as retarded.
Your videos helping me very much so far since I got my gx 2018 last Oct. Thank you Bob. Just 1 thing is remote control can't open automatic when I am outside around the car!!
If you have the 2014 and up, your car should be able to open up automatically once you pull on the door handles. It only works if you pull on the door handles and doesn't open if you're just in the perimeter of the car.
@@GXBOB oh that's why. Unlike sedan Lexus es350. Thank you so much wish u and family a warm holiday season Bob.
Love your videos. Funny too. I tried to find the jack point for the front on my 2013 but it is covered by a skid plate.
Right behind your front tires runs a thick black steel cross beam that runs side to side that attaches your left and right side frame beams. I normally use that intersection.
I saw this video a couple of years ago. I want to ask you why you don't include the spare tire in your rotation. Or do you? I haven't put the spare in rotation but should I?
When I bought the truck, all 4 tires were brand new. The spare was worn. I can not put the spare tire into the rotation because of this. Your truck will veer to one Side while driving. Another reason is because I replace my tires in pairs of I get a flat. If the front driver side goes flat then I replace both driver and passenger regardless if the passenger is still good. I want even wear per axle.
@@GXBOB Do you think I should just keep my spare and not put it in rotation? My GX was new when bought, it now has 20k miles. It seems like a PIA to keep changing spare every 5k miles lol
I was literally planning on asking to do a video on how to lift the car properly and where to position the jack stands. This is very helpful...btw, how many ton are you using for the floor jack.
Sorry to say but its a 2 ton and was originally purchased for my Honda Civic daily driver. I will be purchasing the low profile aluminum 3 ton from harbor freight very soon.
@@GXBOB ok nice, I was debating if I should get the 3 ton or 4 ton but sounds like the 3 ton should be sufficient
@@voicecall26 3 ton works just fine....
Chu Hai, make sure those harbor freight jack stands aint the recall ones.
They've been holding up fairly well. I think i checked them back when the recall came out and my stands are not part of them. Thanks Henrayyyyyyy (=
Hi GXBob, when you get new tires, do you recommend a wheel alignment as well, or is that just overkill recommendations?!? Thanks, Chris
if i change out all 4 then usually i skip the wheel alignment but most folks recommend it to get the full life use of your treads. I typically get a set of tires on the same axle removed and replaced at the same time so yeah i get an alignment for scenarios like that. 4 = no, less than 4 = yes
@@GXBOBThanks, I’ve heard mixed messages, but that sounds good to me. Happy New Year too! 🎉
Hi bob! Thanks for you vids. Prado here. Gonna do this rotation when changing rear pads and discs. Also do you considering getting 12.3 inch android multimedia upgrade for your gx? I ordered same multimedia that looks like 2022 multimedia from gx 460 but for my 2015 prado. It also changes climate control vents position like in newer models.
I haven't switched out my head unit because i haven't found anything i'm willing to spend that kind of money for, especially if its coming from Alibaba or something. I would totally test one out if a company threw me a head unit my direction.
@@GXBOB Yeah prices for head units on gx 460 versions are almost doubled compared to prado considering these units have same specs and harware. I paid 550$ for 128gb 6gb ram model with almost everything they had except 360 camera version that i dont need. I will update on its quality when i get in hands and installed.
so the computer will learn itself that you moved them tires around, so that the TMPS displays correct position?
My best assumption , yes. As there ate no other instructions out there from the dealer or manufacturer that states otherwise. I have not heard from Amy forum that this is even an issue
U the best bro
thanks a lot Eder!
Bob, is that a 3 Ton floor jack? I am looking at harbor freight daytona 3 ton wondering if it will be good enough height wise.
nope, its a 2 ton originally purchased to work on my honda civic. It's time to replace it with something else. I've had it for a long time now. Here is the link to the floor jack i currently have. 2 ton low profile rapid pump.
th-cam.com/video/tdC-aswR2hk/w-d-xo.html
@@GXBOB good to know, I currently have a 2 ton low profile still in very good shape. I guess i can keep using it on the GX until it brakes. What kind of jack are you getting next?
@@bb5op585 I’m looking for any floor jacks that have quick pump features. Because our trucks are so high up in the air as it is, i don’t want a lot of pumps just so my foot jack hits the vehicle frames. Also I’m mostly likely consider long reach one too. I believe harbor has both those options in one for jack model.
www.harborfreight.com/3-ton-long-reach-low-profile-professional-rapid-pump-floor-jack-black-64781.html
Sounds like turkey hunting..lol. Thanks.
Lived in the city my entire life. Turkey hunting is something i had to google.
My driveway is not level. Is it safe to put jack stand on a slope?
I wouldn't.
My driveway also has a slope, but it's also wide enough for me to park sideways near the top where it's more flat & level so I can safely jack up my vehicle.
If you can't do that I would strongly advise bringing it down to street level and doing it there.
@@e5toro7008 Thanks for your suggestion!
depends on how much of an incline that slope is. Mine is very minimal. I put mine on jackstands all the time with parking blocks and e-brakes on. It works as long as the slope is slight.
If one of my standard lug nuts sets deeper than the others, does that mean that I broke it when I used my impact wrench? Or what?
Duuuuuude. WTF. Your impact gun is used to drive your nuts into the wheel at a medium pace. Then the torque wrench takes over. My question is are you sure all 5 lugnuts are identical? If they're not OEM, then you may have a mixture of deep and shallow lug nuts (cars vs suv wheels). Second, how is that possible if you drove all your lug nuts in at the same time slowly so they all seat equally? Third, are you sure the holes in the wheel is centered with the stud? I would take them back out and VISUALLY recenter the wheel without relying on tightening my lug nuts to align my wheels on. Good luck man. I'm sure there is a simple fix to what you just did.
@@GXBOB I didn't just do it. And it has been repeated more than once by other people (besides myself). Maybe it is a different lug nut? I don't think so, but I'll figure it out......
@@GXBOB I get rotations/balances at Discount Tire Company. I do 'other stuff' by myself, which includes removing tires for different jobs. The tech at Discount Tire gave me the wrong lug nut and they replaced it. Freaked me out - I though that I did it somehow. Problem solved!!! I forgot to update you......
I wonder if instead of using 6 ton jack stands, would 3 ton jack stands be ok?
I chose mine for the height reach. It was specifically for trucks
3 ton would be very small for this truck, you can probably put on the rear under the diff, but I would definitely recommend 6 ton jack stand or probably long reach 3 ton might work if you can find one!
Your book said 85 po/ft? My book said it should be 76 po/ft.
at 76ft lbs, your wheels will wobble all the way to walmart for a new set of tires.
www.sparkyexpress.ca/blogs/autoverse/lexus-wheel-lug-nut-torque-chart