What an excellent video!!! No music, no intro, just straight to the topic. What a joy. All so clear as a bell. You folks are the BEST!!!! Very grateful, thank you! Subscribed. Tip - if your washer leaks water, and hoses are not the issue, take out the soap dispenser drawer and give it a good wash in hot water. Also take off the top, then look for a soap dispenser thingie that looks like a distributor cap with tubes coming out of it. This also gets clogged with soap every few years. Label the tubes, label the 'distributor cap piece', then take out the piece and wash it well removing soap debris. Connect it back again, and voila, job done! No more leaks.
Thank you for the tip. We are always happy to help. If you would like to give us a review on Google, we would much appreciate it: g.page/r/CcVUrahZNozMEBM/review We hope that you have a great day!
@@engrkarts4861 even when you have the manuals sometimes they are not always clear. I've had that with my car, I have the technical service manuals but once in a while how to remove some clip is inaccurately printed or there's another trick to it seeing video can help you easily overcome.
Thanks so much for this video. While my machine is not precisely the same, it's close enough that I was able to tear it open with only minimal problems last night. My wife had run an old rug through the machine and the rubber backing on it crumbled into a million small pieces, leading to the drain filter being clogged and the drain hose not working correctly. Once I got the machine opened up, we were able to determine that the tub to pump hose was completely impacted with little bits of rubber. What a mess! Anyway, I can now see a reasonably clear path to getting everything working again, which cost me a bit of time but saved me a great deal of cash.
You're welcome! We are always happy to help. If you would like to give us a review on Google, we would much appreciate it: g.page/r/CcVUrahZNozMEBM/review We hope that you have a great day!
This might be long but this video was a great help. I found this video and used it to remove the front panel because the drain attached to the washer door boot at the bottom was clogged. I believe this is a design flaw since it stays clogged with hair and dirt. Don't know what the purpose of this drain is other than aggravate the customer. I have to daily pull hair out the hole and sometimes stick a long tool in there to work more hair up. The tube makes two 90 degree turns, one to the left and then to the right; that's why it's so difficult to clean without having to remove the front panel! I'm going to have to remove the front panel again, clean the tube, of course reverse procedure and this install a filter in that hole! I'm tired of this! I'm thinking of making a video of this myself!
my washer just clogged and turned itself off with some water inside. the small tube in the bottom-left is also clogged (we live in a beach town and the clog feels like 90% sand), and i can't use a tool to unclog it, so i'm glad this video was here to show me how to remove the front panel and fix the clog, as you mentioned!
Dear Repair Clinic Team, Thanks for the video. My LG washing machine 7KG , which I have been using from last 6 years, the hinge holding the glass frame broke, also the glass cover too. The LG technician told me to discard the machine as there was no parts available according to him. I couldn't find a reason to throw away the machine as It was working ok. I manage to get a second hand glass cover and a hinge. But I didn't know how to open the machine to fix it as the nails which holds the hinges were tight and it was difficult to remove them, even with rust remover. Hence, I used the machine with a rope around for few months until I saw your video. Your video showed where to open, how to open the machine safely. I removed the front sheet, took it to a welding shop where they heated the nuts and it was easy to remove them. So finally I fixed it. The machine it now running like a race horse. Thanks to you. you own every bit of the appreciation. You have saved my money to buy a new machine. I spent only $14 (QR 60) and made me feel confident. Thanks to my father for the support. Only one question arises in my mind. Why the company technicians do not support after the warranty period??? Keep up good work! thanks and regards SK
Thanks for posting this video. I got a repair manual and it was very confusing, but this really showed how to take it apart very easily. I would recommend to anyone needing help or parts.
Thank you so much. This video has just helped me get 'the very stuck' detergent drawer out of my machine - I was only able to open the drawer approx 1cm, but by taking the lid off the machine and being able to get to just get to the screws holding in the front control panel I was able to remove it enough to wiggle and get my fingers in to remove the obstruction and free the drawer. Thank you again.
Thanks a lot for doing this. It wasn't just the $200 I saved, I didn't want to wait 7-8 days for the repair service and hope they had the right hose with them or add a few days.
When re-assembling, you forgot to mention to re-install the screws from the front control mounting panel! I know some people might forget and get confused. Just FYI, if nobody has mentioned it. But, other than that, this video has really helped me out. Thank you!
The plate of the digital clock in mine was moved, due to this I couldn’t see how many time it would take to do a cycle. With this video I fixed it 👍🏻 thankyou
Thank you from Brazil! It is the second time that we use your video to change (actually, clean out of sand) the recirculation and draining pumps, that fill with sand (!). We live at the beach and sandy beach clothes and towels seem get a lot of sand into the machine, and it gets into the pumps.
Thank you guys, this video is awesome. It helped me save tones of money and have the pleasure of working on and fixing my washing machine myself with my son. Thank you !!!
You're welcome! We are always happy to help. If you would like to give us a review on Google, we would much appreciate it: g.page/r/CcVUrahZNozMEBM/review We hope that you have a great day!
Thanks for this, I had to take mine apart because it fell off the platform I made and the lower weight broke off. I got everything back together except I forgot to [lug in the door switch, and putting that seal spring back on was the hardest part.
Thanks! That access worked for me, fortunately was one of the four connections of the block-type switches that was slipping lose, and that was it. Will have to plan for bending a locking clip, or replacing both ends, if that doesn't work well.
Very helpful video, thanks. I removed the front panel to remove the front clean out drain hose (Part #5214FR4006G) that had become blocked by grit/sand. It's a pain to clean out the grit/sand but can be done. The measurements of this drain hose is 1/4"ID by 7/16" OD by 15-7/8" long.
"Click", I love that sound in the video where they just easy breasy remove and reinstall the door latch plug. Meanwhile, I'm over here, breaking a sweat trying to turn and contort my body every which way to get the best handle on this thing, as I am trying my darndest to get it to go up and into place. It's difficult to push in there. It's definitely not a cute little "click". 😂 Great video nonetheless! Thank you so much!
You're welcome! We are always happy to help. If you would like to give us a review on Google, we would much appreciate it: g.page/r/CcVUrahZNozMEBM/review We hope that you have a great day!
very sweet... I am having problem with my door hinge (top) for it has corrosion all over it and the door wont' close. This vid will help me get to it. then I can check for other issues as to where the corrsion is coming from....
yOU people are very good to deal with. always great videos too, to help a do it yourself person. i recommend you to all my friends and family. thank you
Thank you so much for posting this video, after watching your video I was able to disassembled my LG front loader and repaired (front power button misalignment) it myself.
My control button to the power acts like it is dirty or has soap in it, I have to push it several times to get it to engage. I will have to take the front off to see if it is possible to clean. This repair video doesn’t show this but it helps to get me there, will just have to wing it. Thank you for the video.
Thank you for this video. The small black drain hose accessible by the plastic front panel was clogged and I had no idea how to get to to it to unclog it.
We unfortunately do not have a video for the drain hose replacement on this exact machine. We do have that replacement on a similar machine though. If you search for part #1268108 on our website, you'll find the part replacement video at the bottom of the page.
That would be your best bet, yes. Listen to the washer when you run a cycle after removing the shipping bolts to make sure that nothing else is damaged.
Very good tutorial on taking apart machine I have just fixed my machine in 2 hrs. and saved myself alot of money! Some days your the bird some days your the windshield yaaah.
Thanks for the great tutorial, my bosch front loader has rust building up under the soap tray and at the bottom left corner, I want to see if I can fix it before it gets worse
You're welcome! We are always happy to help. If you would like to give us a review on Google, we would much appreciate it: g.page/r/CcVUrahZNozMEBM/review We hope that you have a great day!
You're welcome! We are always happy to help. If you would like to give us a review on Google, we would much appreciate it: g.page/r/CcVUrahZNozMEBM/review We hope that you have a great day!
So I did the bearing replacement on a WM0642HW. I'm not a repair guy.. just joe home owner. However, it pissed me off that you can buy these and then 6 short years later need to replace the bearings. Having done this these videos help but guaranteed I'll never buy another LG product.
Everything was explained perfectly except how do you replace the door on to the new panel? I need to do that cause I am putting in a new front panel. I am wondering how do you attach the door to it
You're welcome! We are always happy to help. If you would like to give us a review on Google, we would much appreciate it: g.page/r/CcVUrahZNozMEBM/review We hope that you have a great day!
Hi Repairclinic, your help will be greatly appreciated. My mother forgot to take away the shipping bolts before starting the same LG machine as you have posted in this clip. She washed the clothes twice in this machine. When I visited her, she complained about the washing machine jumping, so I had a look and removed all the shipping bolts. As i did expect the screws were not complete (partially destroyed). Is the best way to get rid of the destroyed pieces is through opening the rare panel?
You're welcome! We are always happy to help. If you would like to give us a review on Google, we would much appreciate it: g.page/r/CcVUrahZNozMEBM/review We hope that you have a great day!
I love the fact you have detailed videos. However, I have one problem that does not include removing the motor on my LG Dryer. I think it's called a relay. My Dryer starts and then suddenly SLAMS to a stop, trying to start again a few seconds later. My question is how do I fix that without pulling all of this apart?
I replaced my door gasket but did not realize that the black "gasket" on the back side of the control panel that seals the detergent dispenser was not sealing. I used silicone gasket maker from Autozone to repair it. If you remove the control panel, check the area that mates up to the detergent dispenser. It could be leaking also.
Has anybody done this *without* one of those spring expansion tools? Needle-nosed pliers were not wide enough and I could not justify buying one of those from Amazon.ca for > $150. Might as well pay somebody to do it!
Hello, very helpful video. Is there a way to access the inside of the control panel? I have difficulties starting a load, hutton seems off, it is an easy fix I just need to access the contact inside.
I have this same washer. It sat in storage for over 1 year. It smells of mildew, and the cleaned clothes do as well. I tried a few cycles of just water and bleach with zero success. I was told to remove the drain filter. How can this be performed if this is the problem? Thanks ahead of time
You're welcome! We are always happy to help. If you would like to give us a review on Google, we would much appreciate it: g.page/r/CcVUrahZNozMEBM/review We hope that you have a great day!
The washer is not pulling the bleach or the softener from dispenser. I removed the tray and made sure the holes were cleaned and open in the dispenser tray and syphoning holes were open but still doesn't pull it out. Even water down softener per LG web site. Any ideas. The vide was very helpful. do I need to replace the dispenser unit?
Water flow from the valve is what starts the siphon. The water valve may not be letting enough water to flow through the dispenser to make the bleach siphon out. You can also check the water lines to the dispenser the make sure they are not plugged up.
Really gr8 n hlpful. Pls let me know the name of part, three in numbers (made of cement/cast iron) bean shaped (really heavy) fixed around Tub of LG front load Direct drive washing machine. One is in front top of tub (just behind front control panel)and two around rear top of tub. I think these are for controlling vibrations & stability of WM. In my machine front one has come out with bolt and machine has become noisey n shaking badly only while spinning. Any help for repairing the same. Thanx
I have bought a new LG fussy logic 10.0kg fixed as per the instructions but wondering why water does not stay in the drum it flows direct to the drain. I have gone through all program to test but water never stays in drum. Any help
This is a great help, I now know how to get in and out safely. My problem is the machine (Same as in this video it seems LG12576FD) stopped cycle sometime through the night. There is NO power! The board does not light when pressing the power switch. I have emptied out the water but I am not getting any power. The wall socket is fine so not circuit breakers. What could be the issue?
+eAGer4 We would look for a defective noise filter with a blown line fuse. The noise filter is circuit board looking part right by where power cord comes into machine.
+RepairClinic.com The repair guy replaced the main PCB at the rear. I am beginning to think these PCB's have a problem with the heat/cool cycle and circuits are lifting from the board over time :-( I have now had the front and rear PCB's replaced on this machine within 3 years
Can you post pics or video of the door gasket drain hose replacement? where does the hose go after it goes under the balance weight ? where does it connect? The LG exploded view diagrams do not show this at all that I can find.
Is there a way to pull apart the control panel? The screen has shaken off on mine and the digital display is now unreadable and was wondering before I started pulling it apart if it was possible to get it all apart and re-glued without destroying it, and also to know how long it may take me
You're welcome! We are always happy to help. If you would like to give us a review on Google, we would much appreciate it: g.page/r/CcVUrahZNozMEBM/review We hope that you have a great day!
If i want to open it ( right or left side only) to remove and clean the rubber pipe which connects to the pump do i have to proceed to all this steps or less?
My machine is holding the control panel onto the frame pretty tightly. I’ve removed the clips, but something in the center behind the big knob won’t let it move. Any ideas? I’ve followed the video up until this point and re-checked each screw
Do you guys have a video that shows you how to replace the drain pump for an LG Front Load Washer Dryer WM3431H*? I would greatly appreciate the link please.
The old "get what you pay for" adage sure doesn't apply to LG. I was considering their french door refrigerator, also rated #1 by Consumer Reports but not now! My washer went out after just 5 years - only 1 week after my extended warranty expired. Yet LG considers the unit "too aged" and won't help. AGED after just 5 years!? Considering both my cheap $300-400 washers were repair free for min of 10 -20 years, I expected paying nearly 4 times would get me something repair free for a lot longer.
What an excellent video!!! No music, no intro, just straight to the topic. What a joy. All so clear as a bell. You folks are the BEST!!!! Very grateful, thank you! Subscribed.
Tip - if your washer leaks water, and hoses are not the issue, take out the soap dispenser drawer and give it a good wash in hot water. Also take off the top, then look for a soap dispenser thingie that looks like a distributor cap with tubes coming out of it. This also gets clogged with soap every few years. Label the tubes, label the 'distributor cap piece', then take out the piece and wash it well removing soap debris. Connect it back again, and voila, job done! No more leaks.
Thank you for the tip.
We are always happy to help. If you would like to give us a review on Google, we would much appreciate it: g.page/r/CcVUrahZNozMEBM/review
We hope that you have a great day!
I can not comprehend how can one do without TH-cam. TH-cam is a god given blessing to human kind. Thanks very much You Tube
it's Neo like the matrix, trinity i need to know how to fly said helicopter, boom, here it is.
There are manuals but yes, TH-cam is the best.
@@engrkarts4861 even when you have the manuals sometimes they are not always clear. I've had that with my car, I have the technical service manuals but once in a while how to remove some clip is inaccurately printed or there's another trick to it seeing video can help you easily overcome.
Thanks so much for this video. While my machine is not precisely the same, it's close enough that I was able to tear it open with only minimal problems last night. My wife had run an old rug through the machine and the rubber backing on it crumbled into a million small pieces, leading to the drain filter being clogged and the drain hose not working correctly. Once I got the machine opened up, we were able to determine that the tub to pump hose was completely impacted with little bits of rubber. What a mess!
Anyway, I can now see a reasonably clear path to getting everything working again, which cost me a bit of time but saved me a great deal of cash.
Still very useful in 2024 ! Not my exact model, but close enough that I could logic my way through my machine's cabinet disassembly. Thank you !
You're welcome!
We are always happy to help. If you would like to give us a review on Google, we would much appreciate it: g.page/r/CcVUrahZNozMEBM/review
We hope that you have a great day!
This might be long but this video was a great help. I found this video and used it to remove the front panel because the drain attached to the washer door boot at the bottom was clogged. I believe this is a design flaw since it stays clogged with hair and dirt. Don't know what the purpose of this drain is other than aggravate the customer. I have to daily pull hair out the hole and sometimes stick a long tool in there to work more hair up. The tube makes two 90 degree turns, one to the left and then to the right; that's why it's so difficult to clean without having to remove the front panel! I'm going to have to remove the front panel again, clean the tube, of course reverse procedure and this install a filter in that hole! I'm tired of this! I'm thinking of making a video of this myself!
my washer just clogged and turned itself off with some water inside. the small tube in the bottom-left is also clogged (we live in a beach town and the clog feels like 90% sand), and i can't use a tool to unclog it, so i'm glad this video was here to show me how to remove the front panel and fix the clog, as you mentioned!
Dear Repair Clinic Team, Thanks for the video. My LG washing machine 7KG , which I have been using from last 6 years, the hinge holding the glass frame broke, also the glass cover too. The LG technician told me to discard the machine as there was no parts available according to him.
I couldn't find a reason to throw away the machine as It was working ok. I manage to get a second hand glass cover and a hinge. But I didn't know how to open the machine to fix it as the nails which holds the hinges were tight and it was difficult to remove them, even with rust remover. Hence, I used the machine with a rope around for few months until I saw your video.
Your video showed where to open, how to open the machine safely. I removed the front sheet, took it to a welding shop where they heated the nuts and it was easy to remove them. So finally I fixed it. The machine it now running like a race horse.
Thanks to you. you own every bit of the appreciation. You have saved my money to buy a new machine. I spent only $14 (QR 60) and made me feel confident. Thanks to my father for the support.
Only one question arises in my mind. Why the company technicians do not support after the warranty period???
Keep up good work!
thanks and regards
SK
Thanks for posting this video. I got a repair manual and it was very confusing, but this really showed how to take it apart very easily. I would recommend to anyone needing help or parts.
Thank you so much. This video has just helped me get 'the very stuck' detergent drawer out of my machine - I was only able to open the drawer approx 1cm, but by taking the lid off the machine and being able to get to just get to the screws holding in the front control panel I was able to remove it enough to wiggle and get my fingers in to remove the obstruction and free the drawer. Thank you again.
THIS VIDEO IS SO HELPFUL!!! Thanks Repair Clinic for showing the most important steps with no BS!
Just used your video to get to a detergent cap that went into the intake, saved me hours and probably hundreds, thanks!
Awesome!
Thanks a lot for doing this. It wasn't just the $200 I saved, I didn't want to wait 7-8 days for the repair service and hope they had the right hose with them or add a few days.
When re-assembling, you forgot to mention to re-install the screws from the front control mounting panel! I know some people might forget and get confused. Just FYI, if nobody has mentioned it. But, other than that, this video has really helped me out. Thank you!
+Arett Zuniga Hmm, we see it being done at 2:55 of the video.
Thank you for showing me!
The plate of the digital clock in mine was moved, due to this I couldn’t see how many time it would take to do a cycle. With this video I fixed it 👍🏻 thankyou
Good job getting those awkward camera angles, like 1:24. That helps a lot!
Thank you from Brazil! It is the second time that we use your video to change (actually, clean out of sand) the recirculation and draining pumps, that fill with sand (!). We live at the beach and sandy beach clothes and towels seem get a lot of sand into the machine, and it gets into the pumps.
Thank you guys, this video is awesome. It helped me save tones of money and have the pleasure of working on and fixing my washing machine myself with my son. Thank you !!!
You're welcome!
We are always happy to help. If you would like to give us a review on Google, we would much appreciate it: g.page/r/CcVUrahZNozMEBM/review
We hope that you have a great day!
Thank you so much. Helped me to find the issue of broken tub weight balance.
Very helpful. I didn't have the spring expander, but made it work anyways. Thanks for posting the video. Exactly what I was looking for.
You're welcome!
If you would like to give us a review, here is our link: g.page/r/CcVUrahZNozMEBM/review
Have a great day!
Thanks for this, I had to take mine apart because it fell off the platform I made and the lower weight broke off.
I got everything back together except I forgot to [lug in the door switch, and putting that seal spring back on was the hardest part.
Thanks! That access worked for me, fortunately was one of the four connections of the block-type switches that was slipping lose, and that was it. Will have to plan for bending a locking clip, or replacing both ends, if that doesn't work well.
Very helpful video, thanks. I removed the front panel to remove the front clean out drain hose (Part #5214FR4006G) that had become blocked by grit/sand. It's a pain to clean out the grit/sand but can be done. The measurements of this drain hose is 1/4"ID by 7/16" OD by 15-7/8" long.
+David Greenaway Thank you for sharing.
I did the same thing too but it was packed with pet hair.
Thank you so much! You saved us a week and a half waiting for our warranty repair man to come out! A+++
Scott Jack Awesome!! Congrats!
I needed some direction on how to remove the front cover plate. This video was perfect. 1:53 Thanks!
You're welcome!
If you would like to give us a review, here is our link: g.page/r/CcVUrahZNozMEBM/review
Have a great day!
"Click", I love that sound in the video where they just easy breasy remove and reinstall the door latch plug. Meanwhile, I'm over here, breaking a sweat trying to turn and contort my body every which way to get the best handle on this thing, as I am trying my darndest to get it to go up and into place. It's difficult to push in there. It's definitely not a cute little "click". 😂 Great video nonetheless! Thank you so much!
You're welcome!
We are always happy to help. If you would like to give us a review on Google, we would much appreciate it: g.page/r/CcVUrahZNozMEBM/review
We hope that you have a great day!
very sweet...
I am having problem with my door hinge (top)
for it has corrosion all over it and the door wont' close.
This vid will help me get to it. then I can check for other issues
as to where the corrsion is coming from....
Very helpful. I need to remove those heavy counter weights so I can lift the washer up stairs. Way to heavy for my old wooden stairs out back!!
Great video. This worked perfectly for my Kenmore Elite. It made taking the machine apart simple.
Vxeeesrvcxreacfulk. Day
Gffdsayvfxdyuvxxddcxxxxxxxxx
That's awesome! We're glad that you were able to get the part in a timely manner and that you had an easy (and impressive!) repair.
This is a reply from 10 years ago...
yOU people are very good to deal with. always great videos too, to help a do it yourself person. i recommend you to all my friends and family. thank you
Thank you so much for posting this video, after watching your video I was able to disassembled my LG front loader and repaired (front power button misalignment) it myself.
I particularly went to this for removing the top of the front loader for access to hose connections. Bummer
Dude me tooooo
My control button to the power acts like it is dirty or has soap in it, I have to push it several times to get it to engage. I will have to take the front off to see if it is possible to clean. This repair video doesn’t show this but it helps to get me there, will just have to wing it. Thank you for the video.
Thank you for this video. The small black drain hose accessible by the plastic front panel was clogged and I had no idea how to get to to it to unclog it.
+oscartmic Good work!
Thank you for making this video and thank you LG for making it so simple
So unbelievably helpful
We unfortunately do not have a video for the drain hose replacement on this exact machine. We do have that replacement on a similar machine though. If you search for part #1268108 on our website, you'll find the part replacement video at the bottom of the page.
It would be helpful if there was a video showing how to take the drum out (all the way) properly.
Thank you very much!
The lid removal was just what I needed. It worked on my 2009 WM2101HW, exactly as you show.
Good on ya!
swanny
Thank you for the video. Very helpful for getting to the thermistor when a "tE" error was indicated.
That would be your best bet, yes. Listen to the washer when you run a cycle after removing the shipping bolts to make sure that nothing else is damaged.
Thanks for this video, it saved me a lot of headache and hundreds of dollars.
Very good tutorial on taking apart machine I have just fixed my machine in 2 hrs. and saved myself alot of money! Some days your the bird some days your the windshield yaaah.
David Alexander We're glad we could help!
I watched this video because I had mice in my washing machine🤣🤣🤣🤣🤣🤣
Thanks for the great tutorial, my bosch front loader has rust building up under the soap tray and at the bottom left corner, I want to see if I can fix it before it gets worse
You're welcome!
We are always happy to help. If you would like to give us a review on Google, we would much appreciate it: g.page/r/CcVUrahZNozMEBM/review
We hope that you have a great day!
Thank you for saving me money! Parts ordered!
You're welcome!
We are always happy to help. If you would like to give us a review on Google, we would much appreciate it: g.page/r/CcVUrahZNozMEBM/review
We hope that you have a great day!
Thanks for posting this video. It was exactly what i needed!
So I did the bearing replacement on a WM0642HW. I'm not a repair guy.. just joe home owner. However, it pissed me off that you can buy these and then 6 short years later need to replace the bearings. Having done this these videos help but guaranteed I'll never buy another LG product.
Excellent video, going through all details. I was able to open my LG washer. Thank you.
Cool thanks!
Everything was explained perfectly except how do you replace the door on to the new panel? I need to do that cause I am putting in a new front panel. I am wondering how do you attach the door to it
Very grateful. Thank you.
You're welcome!
We are always happy to help. If you would like to give us a review on Google, we would much appreciate it: g.page/r/CcVUrahZNozMEBM/review
We hope that you have a great day!
Hi Repairclinic, your help will be greatly appreciated. My mother forgot to take away the shipping bolts before starting the same LG machine as you have posted in this clip. She washed the clothes twice in this machine. When I visited her, she complained about the washing machine jumping, so I had a look and removed all the shipping bolts. As i did expect the screws were not complete (partially destroyed). Is the best way to get rid of the destroyed pieces is through opening the rare panel?
Thank you very much for the video!
You're welcome!
We are always happy to help. If you would like to give us a review on Google, we would much appreciate it: g.page/r/CcVUrahZNozMEBM/review
We hope that you have a great day!
I love the fact you have detailed videos. However, I have one problem that does not include removing the motor on my LG Dryer. I think it's called a relay. My Dryer starts and then suddenly SLAMS to a stop, trying to start again a few seconds later. My question is how do I fix that without pulling all of this apart?
Exactly what I was looking for. THANK YOU !!!
Todd Jandro Thank you.
This video was a life saver
Tremendously helping video. Thank You.
We have a drain filter replacement video for part #1267432. If you go to our website and put that part number in you'll be able to see the video.
Great! We're happy to help.
I replaced my door gasket but did not realize that the black "gasket" on the back side of the control panel that seals the detergent dispenser was not sealing. I used silicone gasket maker from Autozone to repair it. If you remove the control panel, check the area that mates up to the detergent dispenser. It could be leaking also.
***** Thank you for your input.
Awesome! So glad you found it helpful!
Has anybody done this *without* one of those spring expansion tools? Needle-nosed pliers were not wide enough and I could not justify buying one of those from Amazon.ca for > $150. Might as well pay somebody to do it!
Nice demo ☺️
Hope to take a look inside.
Behzad A. We hope it goes well!
sure.
Hello, very helpful video. Is there a way to access the inside of the control panel? I have difficulties starting a load, hutton seems off, it is an easy fix I just need to access the contact inside.
Is this what you're looking for? www.repairclinic.com/PartDetail/Tub-to-Pump-Hose/4738ER1002A/1266823?modelNumber=WM1832CW
Thank you .. that's what I was looking for !!
Thank you very much for the video. Very useful.
John Smith Thanks for watching.
I have this same washer. It sat in storage for over 1 year. It smells of mildew, and the cleaned clothes do as well. I tried a few cycles of just water and bleach with zero success. I was told to remove the drain filter. How can this be performed if this is the problem? Thanks ahead of time
Your drain hose is probably too low. The drain hose has to raise up to at least the height of the top of the washer to perform correctly.
Thanks for saving some money 💸💸😂😂🎉🙏
You're welcome!
We are always happy to help. If you would like to give us a review on Google, we would much appreciate it: g.page/r/CcVUrahZNozMEBM/review
We hope that you have a great day!
Greetings leadership!!
I like your video, are helping
Can you get a screwdriver in there to press the dispenser down?
Very useful information ! Thanks..
Eliusalmo1 You're welcome.
I watched this to see how the washer is constructed. Shocked at the amount of plastic, and plastic in places it shouldn't be.
Can you please send lg pedestal washer repair videos. I want it very much need....
The washer is not pulling the bleach or the softener from dispenser. I removed the tray and made sure the holes were cleaned and open in the dispenser tray and syphoning holes were open but still doesn't pull it out. Even water down softener per LG web site. Any ideas. The vide was very helpful. do I need to replace the dispenser unit?
Water flow from the valve is what starts the siphon. The water valve may not be letting enough water to flow through the dispenser to make the bleach siphon out. You can also check the water lines to the dispenser the make sure they are not plugged up.
What would make the lines clog? I have a water softener but I notice that it gets mold in there
Thank you
Do you have a video that shows how to access a front loading washer from LG and thermistor check/replacement?
Really gr8 n hlpful. Pls let me know the name of part, three in numbers (made of cement/cast iron) bean shaped (really heavy) fixed around Tub of LG front load Direct drive washing machine. One is in front top of tub (just behind front control panel)and two around rear top of tub. I think these are for controlling vibrations & stability of WM. In my machine front one has come out with bolt and machine has become noisey n shaking badly only while spinning. Any help for repairing the same. Thanx
I have bought a new LG fussy logic 10.0kg fixed as per the instructions but wondering why water does not stay in the drum it flows direct to the drain. I have gone through all program to test but water never stays in drum. Any help
This is a great help, I now know how to get in and out safely. My problem is the machine (Same as in this video it seems LG12576FD) stopped cycle sometime through the night. There is NO power! The board does not light when pressing the power switch. I have emptied out the water but I am not getting any power. The wall socket is fine so not circuit breakers. What could be the issue?
+eAGer4 We would look for a defective noise filter with a blown line fuse. The noise filter is circuit board looking part right by where power cord comes into machine.
+RepairClinic.com The repair guy replaced the main PCB at the rear. I am beginning to think these PCB's have a problem with the heat/cool cycle and circuits are lifting from the board over time :-( I have now had the front and rear PCB's replaced on this machine within 3 years
Unfortunately we don't have a thermistor video for LG washers. Sorry about that.
SUBSCRIBED Thanks!
You're welcome!
Can you post pics or video of the door gasket drain hose replacement? where does the hose go after it goes under the balance weight ? where does it connect? The LG exploded view diagrams do not show this at all that I can find.
Can you tell me how to fix the LG front load washer when the problem will do the code word is LE
Is there a way to pull apart the control panel? The screen has shaken off on mine and the digital display is now unreadable and was wondering before I started pulling it apart if it was possible to get it all apart and re-glued without destroying it, and also to know how long it may take me
I lost my rings in this exact same washer. By taking it apart according to the video, will I be able to find them? Where would they most likely be?
Thanks for the video =)
Ty.
You're welcome!
We are always happy to help. If you would like to give us a review on Google, we would much appreciate it: g.page/r/CcVUrahZNozMEBM/review
We hope that you have a great day!
Can we use the washing machine to keep remove the main top?
Any easy way to get the detergent dispenser to release. It is stuck and appears that the softener dispenser is blocking it from opening up freely.
If i want to open it ( right or left side only) to remove and clean the rubber pipe which connects to the pump do i have to proceed to all this steps or less?
What a great help this video is! Thanks :)
How to dismantle the front glass door and replace the door hook?
A great help Thanks!!!
My machine is holding the control panel onto the frame pretty tightly. I’ve removed the clips, but something in the center behind the big knob won’t let it move. Any ideas? I’ve followed the video up until this point and re-checked each screw
Do you guys have a video that shows you how to replace the drain pump for an LG Front Load Washer Dryer WM3431H*? I would greatly appreciate the link please.
Is it possible to remove the inner plastic parts that contain 4 balls, located inside the barrel?
Professional!
The old "get what you pay for" adage sure doesn't apply to LG. I was considering their french door refrigerator, also rated #1 by Consumer Reports but not now! My washer went out after just 5 years - only 1 week after my extended warranty expired. Yet LG considers the unit "too aged" and won't help. AGED after just 5 years!? Considering both my cheap $300-400 washers were repair free for min of 10 -20 years, I expected paying nearly 4 times would get me something repair free for a lot longer.