Hot Tub FLO Error Code / Hot Tub Not Heating / Hot Tub Error Message
ฝัง
- เผยแพร่เมื่อ 2 ต.ค. 2024
- Hot Tub FLO Error Code / Hot Tub Not Heating
A hot tub not heating or just not heating up to temperature will sometimes show an error code
on the hot tub topside panel. Finding the hot tub Flo error code and where the problem is can be frustrating. Follow this video and others on our channel and you will find the hot tub flow issue fast.
❤ SUBSCRIBE - www.youtube.co...
🎁TIP JAR - PAYPAL: info@vippools.ca
Legal Notice: Any electrical connected to your hot tub or swimming pool should be worked on by a licensed electrician or service technician. Please call your local pool/hot tub Technician for a service call before doing any work yourself.
-------------PAID LINKS BELOW-----------------------------------
✔ Hot Tub Test Kit:
amzn.to/3xGeKvo CANADA
amzn.to/2LOl2nb (small kit)
amzn.to/3rO71W3 (large kit)
✔ Hot Tub Pump Capacitor Tester:
amzn.to/3JYgfaO CANADA
amzn.to/3uPw0wu USA
✔ Hot Tub Volt Tester:
amzn.to/36odwJY CANADA
amzn.to/36v17Ek USA
✔ Volts and Amps Tester
amzn.to/37qsKyA CANADA
amzn.to/3Mej4Gl USA
❤ FACEBOOK - / vippoolandspa
😎 Join this channel to get access to perks:
/ @vippoolsandspas
#hottub #hottuberrorcode #spaerrormessage #hottuberrors #hottubmessages
![[Full Episode] The Restaurant War Thailand ศึกพ่อค้าซ่าแม่ค้าแซ่บ Episode 2 | 29 ก.ย. 67](http://i.ytimg.com/vi/r3lfLNH6Ke4/mqdefault.jpg)
Simple way of finding the problem.
You said if their air comes out of that when you remove it. Obviously there’s gonna be water that’s going to come out, so should we listen for air bubbles or just air? Because obviously there’s gonna water that comes out of it. So should we listen for air and water to come out?
Hi, wonder if you can help? We have a vita joli spa. The heater is not working, and hence get a flow indication on the panel. There are two jet settings on the control panel, and have noticed that when jet1 (which has low and high settings) that the first low setting has no flow. The high setting seems to work fine as does jet2 and the blowers? Any help much appreciated
Can you send a picture of your pump too info@vippools.ca. and the control box.
Great video. Thank you. I have a FLO error on my spa running a Gecko Xe Spa Pack. Tub is new(ish) manufactured in 2017 and cleaned religiously. I’ve reset the breaker, changed filters, checked for air lock, etc. FLO keeps appearing after an hour or two. Filter cycle still runs, and the tub has great water flow and heat. Just locks out the console with FLO. I’ve taken the heater out to check for debris/hair on the flow sensor, but it’s shiny clean inside (no rust). I don’t think the heater has a flow/pressure sensor that can be removed (HEAT.WAV.XE-4-240-2INC-IF-T). Do I need to replace the entire heater? Troubleshooting guide states that at this point I need to replace the Spa Pack, but that seems insane overkill and unnecessary expense. Any ideas would be greatly appreciated at this point. Nobody wants to service spa’s a that moment due to COVID-19. I’m handy, and comfortable with any suggestions. Thanks!
Unfortunately, you cant change the heater element or any of the sensors. That heat tube is all one piece. Need a new tube. GK 9920 101435. That's the 4kw. Sorry it wasn't easier. That's just one of those packs out there.
Another thing for you. Keep the old heat tube. You can use the old element when the new one goes. Not sure why Gecko doesnt sell parts for that. There just isnt item codes for parts,, so that's even harder, even if there out there.
VIP Pools and Spas Thank you for your help. So the recommendation is to replace the heat tube assembly, and not the entire spa pack?
Yes. Just the heat tube.
So.......did you find out what the issue was?
Any idea on a dynasty Nassau-ll-xt, it displays 291 and then r3 and then LL3 and then --- ^ ; the arrow is pointing at the filter symbol and then it recycles through all the same display on and on. At the end of the cycle I can hear a mechanical or electrical click near the heating control panel thing. If I turn on the jets using the timer on the wall, I hear a loud pump running but no jets or anything turn on. I tried taking filters off and shutting the power off and turning back on again. Nothing seems to fix it, it doesn't heat up or anything. Thanks!
Is pump one working? When you say loud, what does that mean. See my other videos on pump bearing repairs. I do have a few if them that make a loud noise. Sounds to me it's the spa pack
Hi, I have ACC system and when the system should heat the water I receive a massage PSOC and the heater is not working, do you know what can be the problem? all the pumps are working ans I don't have an air lock. Thanks
It may be the pressure switch or some other flow issue. Jumpering the switch to see if that's the pro problem. If heat turns back on.....change the switch. NOTE...DO NOT leave the pressure switch jumpered, replace the switch.
@@VIPPoolsandSpas Thanks
hi have you any idea what the problem is with this ...
the spa hadnt been used for a while, when I switched on it said flo, i turned it off then on a few times and all seemed well, however the light wasnt working nor was the temp adjustment on the topside panel, the jet button worked fine, the tub heated up but only to 37º warm but not hot ... i assumed there may be a bad connection on the control panel so i unplugged it and checked cable, it looked fine so i plugged it back in .. unfortunately i hadnt lined the pins up with the control panel connection, they ended up one hole to the left so one pin exposed on the right and one hole exposed on the left ... when i switched on i now get this, flickering ... it starts up with jets and flickers what looks like 700 then the tub after 30 seconds jets shut off and it flickers 00 ... non of the buttons now function... i tried an new control panel, but its just the same :/ it has a CTI board and controller mini max digital spa pak DWG-#4-30-1806D-3 strong spa cyprus ... th-cam.com/video/ifZqQ6DudCI/w-d-xo.html
I have an older aegean hot tub lps 220 model and it comes up flashing SnS and dr and DrY .The temp is reading normal but when I go to heat it up the numbers fly up the water only warms up a little bit probably 2 or 3 degrees and all the error codes go away when the jets are on. Everything else works fine just the temp .Any way to resolve this ?
Edit: on economy mode it seems to read a reasonable temp with no codes , as soon as I put it into standard it flahes with SnS and then DrY after a few minutes
SNS is a sensor. BUT. sounds like a flow issue when you also get DR or DRY. pull filter? is the flow good (pump that pushes water thru the heater tube)
I have a flow code coming on after draining it to were heater don't kick on, does it matter which union on left or right to loosen to try and get the air out and do u need the jets on while trying to get air out, thanks
If you can get to the front of the pump that pushes water thru the heat tube, I would try and loosen that one first. I sometimes turn the pump on high speed. You can hear the air coming out and when it speeds up, I tighten the union back up.
Thanks I'm gonna give it a try, I have a thermospas hot tub that's only like 3 years old, I ordered a new heat pump and have it but wanna make sure it's just not a air problem 1st, thank you and I will post after I try it and let u know what happens
My hot tub states heater too hot, then shuts off, then states press button to reset. I do this and it works for a day or too, but then the same error code comes on. What could this be? Please help? My local pool store states the THINK it's the circuit board and want to charge me 880$ for a new one..............
Not sure the spa pack you have but, replace the high limit sensor
My no 2 motor pulsates up and down is that a sign the motor is going it's off and on as of now come and goes and my thermostat I set at 95 and 2 days later its 101 and will get hotter what is it I have the parts but dont want to be chasing it
low water, something in the pump or heat tube. Hard to say what it is without seeing and hearing it. Did you do anything to the tub? Repair anything, filter, clean tub out? Try removing the filter and see if that makes a diff.
We had a recent brown out issue where our electrical power was spiking up and down at the house. After the electrical utility fixed that issue we then had a problem with our Jacuzzi hot tub where we have a 'FLO' error that won't go away. Typically what would be the first thing to check after power issues like that (pump? heater?)?
When you get a power surge coming into your house this can do damage to any hot tub. If you have a FLO issue after a surge or a brown out, it could still be your pressure switch. Make sure your circ pump is working and test all fuses in the pak. If all good try these things also... 1) pull filter and check that. 2) open spa pak and check for burn Mark's on the board. 3) test or replace pressure switch. 4) if you hit this point......replace the board.
Hot tub is not heating. I have great flow on my jets. I am getting dr and dry codes. My temperature gauge goes from 90 to 104 like you are counting and then kicks off. I thought my circulartion pump was going out. I removed my circulation pump and checked the impeller and no blockage but pump is running. Any ideas? Could my circulation pump be working but just not pumping enough? Thank you in advance for any help.
Additionally, it may be labeled as a jet pump. It's a 2 cycle 12/4.4 amp. I am getting no flow from the warm water return at any time. My tub is a 3 zone and the jet pump only turns in when I have a certain zone on. Otherwise, it is not spinning. Should it be spinning 24/7? And even at that time, no water is flowing from the warm water return.
Depends on what style spa pack you have (the box everything plugs into). If its a Balboa, might be a sensor issue or High Limit issue. Can you tell me the name of the spa pack?
@@VIPPoolsandSpas It is a 2008 master spas legends series. I've bled all the lines and replaced filters.
@@24csturner need to know what type of pack is running everything.
@@VIPPoolsandSpas it looks like a Balboa model number MS5000
Tenho um alarme 1 o que é esse alarme
Thank you it was vary useful
Hi. Thanks for the video. How can I be sure that the problem is with this switch and that I need to change it?
Thank you.
Just replace the pressure switch if you feel that is it. Not an expensive part.
Great info - sort of a odd question for you. Do you have the power shut off to the tub when you work on the pressure switch?
have power on ONLY to turn the pressure switch. dont touch the wires or the board when doing this. your just listening for the relay "click". that means, the relay turned the heater on and your 3 lights should be gone.
turn power off power when changing that pressure switch.
I have a hot spring hot tub is this video for any tub?
doesnt matter the name of the hot tub. if its a balboa spa pack it doesnt have a pressure switch.
And idea for a circuit box being fried??
depends how bad. You can get a computer repair guy or electronics guy to look at it. They might be able to help you out.
K thanks 🤙🏽
getting a FLO error and pump 1 wont come on for circulation. I bled the air to make sure I don't have an airlock, but pump one wont come on. I recently replaced pump one (2 speed pump), and confirmed the proper wiring, and still no joy from pump 1. Pump 2 runs, even with the flo error, but only half the jets are working. Any advice?
Sorry. Your message didn't clear my comment section for some reason. FLO error comes on because of pump 1 not turning on. Check filters and flow. Check pump fuse also. Pump 1 is the problem. Let me know. Sorry again about the delay.
will this fix when you have . DRY error code?
If you have a Balboa spa park then it's a sensor issue.
@@roberthaley5448 will changing the sensor correct the issue?
What error code do you have? If a FLO or DRY error code is on the top side, try removing the filter first. If you just drained it and refilled it and these codes come up.........then it's an air lock.
Also what does error pr mean
It's not an error code, it's just telling you it's purging. Normally you see that when you turn the power off and back on again. It will go thru it's programming, showing PR and sometimes other letters or numbers. It will go away when it done. No biggy
My tub is throwing a Cc code and will not let me push the temp button to raise it up or down, any thoughts?
Can you send a picture of that code too info@vippools.ca
Whats the name of the hot tub? Was anything changed on the hot tub or New to the hot tub?
@@VIPPoolsandSpas not that I know of, and it is a GL spas
I sent an email. Just need some more info. Balboa still looking into it. What I could find is. "CC - Clean up Cycle Duration (some systems only) When set to CC0, clean up cycles are disabled. When set to CC1 through CC4, the number indicates how many hours each clean up cycle will run."
But you said that you have no control...UP or DOWN on the Temp? Right?
@@VIPPoolsandSpas correct when I push the button that typically would change the temperature nothing happens. Also thank you so much for looking into this!
Doesn't show us how to change it?
Sorry. Its easy. if changing the pressure switch, drain tub, take off both wires and unscrew counter clockwise. when putting new switch back in, make sure you dont cross thred it, its only plastic. and only hand tight.
VIP Pools to late, i changed it with the water in it, shut the breaker off, stuck my finger on the hole to stop the flow from coming out, screwed the new one in, blow dried what got wet and turned the breaker back on
Boom back in business
;)