I shared this video with my mechanic who initially suggested I replace the entire transfer case. He replaced the $100 chain and my ML350 runs great. Thank you for posting.
I have the same problem with my 2011 ml 350 4matic I went to the dealer they told me I need to replace the whole thing cost over 4 grands. Thank God I came across this video. I might be good replacing only the belt.
Wow! You made that look so easy! My 2014 ML350 Bluetec just started skipping-- 117K miles-- I replaced the motor mounts and transmission mount about 3 months ago. They were a pain! Took me two days. Really enjoyed your professional quality audio and video! Thank you!
My GL is at 130K miles now and still not skipping but I can't help think perhaps I ought to change this chain anyway to pre-empt any issues which might cause wear on the sprockets. The transfer case has had two oil changes since I bought it at 38K miles so I hope I've staved-off any wear so far. Thing is, the GL has high/low range and I believe the chain is different which I'm struggling to find here in the UK. If anyone has a part No, I'd be grateful. Thanks, and thanks for the video. This was extremely helpful. My only fear is working underneath the car. I have monstrous axle stands (6 tons each) and a 3 ton trolley jack but when I changed the airbag springs, I still couldn't bring myself to get under it. It's a bit of an irrational phobia I guess.
My factory MB manual gives their "two-step" torque technique for the driveshaft bolts, torquing to an initial value in phase 1, then turning an additional 90 degrees in phase 2. The values differ for front and rear. In the front at the transfer case, it is 40 Nm, plus 90 degrees, in the rear at the diff it is 60 Nm, plus 90 degrees. In US measure (conversion factor is 1.356) that is 29 foot pounds plus 90 degrees in front at the case, and 44 foot pounds plus 90 degrees in the rear at the diff.
Well she told me it was clicking but kept driving it so she was very lucky. I actually did the repair a year ago but just now got it edited and uploaded. Soon I'll get my cherokee build uploaded.
@shawnmrfixitlee6478 this is my 03 WJ build, bigger rad, deleted the hydraulic fan, lifted, winch bumper, lockers, and soon the h.o. engine with headers. I use it to pull my stump grinder for the tree service.
@shawnmrfixitlee6478 ha ha guess what I have some prius videos coming up lol I bought one to run back and forth to my ranch when fuel was sky high. The f250 w the 7.3 only gets 10mpg so got the prius so I can run out there and feed the animals and water the giant garden.
I absolutely luv watching your videos! I have this same vehicle but wldnt dare attempt to take apart like you just did but very fun to watch. Tks for sharing.
Thanks! Ahhh it wasn't that bad just took some time. I've been building transmissions and transfer cases since I was a kid building 4x4 lifted trucks. And have several awd vehicles myself, and guess who has to do all the repairs lol
I just changed the fluid in my transfer case in a W251 -07 chassi after 70k miles, and the transfer case inside was metal clean, the oil was little bit dark red, how come this one was so dirty and full of sludge? How many miles your car had?
Thanks for your video,i was able to get it done but now the car won’t start 😢😢. Have power but it won’t crank. Any idea what can be the issue?? The air suspension compressor too is dead
Great video! Thank you. Could not remove my driveshaft from transfer case though, all bolts out, soaked with rust blaster and still won’t budge. Had to do complete chain chain out with section still attached to driveshaft. any hint on how to separate both? Thank you. Rick
2 or 3 days because I was filming and the owner ordered in the fluid so I had to wait on that, along with filming. But this can easily be done in a day.
Hi Cody, You have agreed to do collab with us and took the product from us and never created a video and posted on your social media channel. Can you please tell me any ETA when you can post? Product was sent to you in August 2023!
![Gl ML R clicking knocking pinging fix under acceleration [chain replacement] (easy)](/img/n.gif)
Check out Www.snacksforme.com for some of the best snacks!!
Hey buddy, just saved me 4k repair !! 🙏🏽 can you please share the part number for the transfer case chain? I have Mercedes ML 350 2011 w164. Thanks
I shared this video with my mechanic who initially suggested I replace the entire transfer case. He replaced the $100 chain and my ML350 runs great. Thank you for posting.
I have the same problem with my 2011 ml 350 4matic I went to the dealer they told me I need to replace the whole thing cost over 4 grands. Thank God I came across this video. I might be good replacing only the belt.
Wow! You made that look so easy!
My 2014 ML350 Bluetec just started skipping-- 117K miles--
I replaced the motor mounts and transmission mount about 3 months ago. They were a pain! Took me two days.
Really enjoyed your professional quality audio and video!
Thank you!
Thanks I try to make the videos as best I can while showing the best way to get it done.
My GL is at 130K miles now and still not skipping but I can't help think perhaps I ought to change this chain anyway to pre-empt any issues which might cause wear on the sprockets. The transfer case has had two oil changes since I bought it at 38K miles so I hope I've staved-off any wear so far.
Thing is, the GL has high/low range and I believe the chain is different which I'm struggling to find here in the UK. If anyone has a part No, I'd be grateful. Thanks, and thanks for the video. This was extremely helpful. My only fear is working underneath the car. I have monstrous axle stands (6 tons each) and a 3 ton trolley jack but when I changed the airbag springs, I still couldn't bring myself to get under it. It's a bit of an irrational phobia I guess.
My factory MB manual gives their "two-step" torque technique for the driveshaft bolts, torquing to an initial value in phase 1, then turning an additional 90 degrees in phase 2. The values differ for front and rear. In the front at the transfer case, it is 40 Nm, plus 90 degrees, in the rear at the diff it is 60 Nm, plus 90 degrees. In US measure (conversion factor is 1.356) that is 29 foot pounds plus 90 degrees in front at the case, and 44 foot pounds plus 90 degrees in the rear at the diff.
Great work Cody .. it was time to do that before it tore up the case and bearings .. You saved her a ton of $$...
Well she told me it was clicking but kept driving it so she was very lucky. I actually did the repair a year ago but just now got it edited and uploaded. Soon I'll get my cherokee build uploaded.
@@CodytheCarGuy yes.. Jeep guy here !
@shawnmrfixitlee6478 this is my 03 WJ build, bigger rad, deleted the hydraulic fan, lifted, winch bumper, lockers, and soon the h.o. engine with headers. I use it to pull my stump grinder for the tree service.
@@CodytheCarGuy SWEET ! keep the jeep burn the EV'S .. 0IIIIIII0
@shawnmrfixitlee6478 ha ha guess what I have some prius videos coming up lol I bought one to run back and forth to my ranch when fuel was sky high. The f250 w the 7.3 only gets 10mpg so got the prius so I can run out there and feed the animals and water the giant garden.
Question about filling that with fluid. How do you get the fluid in that hole? And how much do you put in there?
I absolutely luv watching your videos! I have this same vehicle but wldnt dare attempt to take apart like you just did but very fun to watch. Tks for sharing.
Thanks! Ahhh it wasn't that bad just took some time. I've been building transmissions and transfer cases since I was a kid building 4x4 lifted trucks. And have several awd vehicles myself, and guess who has to do all the repairs lol
Nice work!
Thanks! Editing the video almost took as long as doing the repair.
I just changed the fluid in my transfer case in a W251 -07 chassi after 70k miles, and the transfer case inside was metal clean, the oil was little bit dark red, how come this one was so dirty and full of sludge? How many miles your car had?
Made that look too easy lol. Where are you located? Must be the south because I heard a rooster in the background in the beginning of the video.
Thanks for your video,i was able to get it done but now the car won’t start 😢😢. Have power but it won’t crank. Any idea what can be the issue?? The air suspension compressor too is dead
did u get car started?
Great video! Thank you. Could not remove my driveshaft from transfer case though, all bolts out, soaked with rust blaster and still won’t budge. Had to do complete chain chain out with section still attached to driveshaft. any hint on how to separate both? Thank you. Rick
You just have to hammer it
While fitting the case comer be careful not to rub off the RTV if not you will have a leak after
What is a good brand for the chain ?
Mine skipping only under heavy load in first gear but ill replace it
Whats the torx for the bolts on the rear drive shaft?
how much would this job cost roughly at service shop??
On my 2011 ML350 Bluetec I found the driveshaft bolts were T55 rather than T50
How long did it take you to complete the work on this.
2 or 3 days because I was filming and the owner ordered in the fluid so I had to wait on that, along with filming. But this can easily be done in a day.
Hi Cody, You have agreed to do collab with us and took the product from us and never created a video and posted on your social media channel. Can you please tell me any ETA when you can post? Product was sent to you in August 2023!
You never put the foot punds for the drive shaft.
where are you located?
@@JeromeCooke-w9p Mississippi
@@CodytheCarGuy what part of MS, I’m in Mississippi too and I have a ML350 I’d like to have you take a look at if possible.
Not that easy for 2008 e350 4matic