Thanks very much for your video I had just damaged my DT830B by setting DCV and connecting to AC voltage. I was going to throw it away when I disassembled and saw these tiny SMD components. How to find the faulty one??? The I saw your video orienting to check the resistor and identifying the faulty one!! I did the same and found a similar sign on one of the resistors, when checked it was faulty! It was a 900 ohms. I then removed it and replaced it with a 102 (very close) also SMD The multimeter is back in business! (It measures AC 10% higher though) Thanks a lot my friend Best regards
@@AmanKhan-ec6lg Most certainly, my friend I have looked for the resistor with signs of damage according to the orientation in this Vídeo. The resistor I found to be defective was the 9000 (900 ohms) I replaced it with another one that was available of 1000 ohms. The result was good, because it started again to measure voltage, although with an increase of 10% in the read value. So I bought the right resistor (900 ohms) and replaced and now it is ok. U can try to identify with a magnifier or u can measure with some other multimeter. Best luck for u Regards Salu from Rio de Janeiro
i have some resistor show the lower value than the actual number showing on SMD when i remove the smd n measure it the result is normal then i put back on the resistor my multitester going erratically no short circuit just after i change the new buzzer to the louder one then the problem happen
My brother "Anees Ahmed" thank for your support ,,, I make 93 videos ,,,, Hope that you may like also,,,,, Many many thanks my brother & have a nice day.
Good, BUT I cannot understand how you converted SMD code into Ohm? What I know it is 1200 M Ohm because: 128, a Three Digit Code, follows: = 12 x (10 x 8) OR 12E8 = 1200000000 Ohm = 1200000K Ohm = 1200M Ohm OR 1200 Meg Ohm Please correct me if I am wrong Neither of your tested resistors gave accurate readings, the big 470 Ohm resistor you checked gave > 580 Ohm, why is that?
Sir, I have one DMM (HAOYUE DT830D). Problems are as follows: (1) Installed new battery 9 volts, the broblem is that inspite of fulled battery, in mode there is no display only dot is displayed ( Like (.) and on bugger/continue mode only (-1) minus one is displayed and slowly it disappeared. will you kindly give solution to what shall i check on PCB of DMM and why such problems are arised whether due to the fixed I.C.(Black) any bad components like Registors/diat/capacitors/bugger attachments. Pl slove the prblems Sir.Thanks.
Your video is very interesting bro. . My multimeter DT-830D. By mistake I checked AC current when the red probe was inserted to 10A-DC. Now the multimeter display is there, but it is not reading AC or DC voltage or the continuity. Checked for any burnt SMD or other part, but could not find any damaged component. Can you pls advise me how to repair this multimeter Thank you.
Excuse me sir do you have the schematic for the exact same model? I'm trying to figure out the value of each smd capacitor especially the one that is located near the top left corner next to the big green mylar capacitor.
Nice video......keep it up........I have MECO 27 auto multi meter in it 230 AC voltage is showing 0 and some time it shows 70 volt not shows exact voltage so what's the issue please suggest........!!! What to do if this issue is inthis yellow Meter.....?????
My brother "Nicks Torc" first thing thank you for comment me . My brother this type of clamp meter is used to detect the induction current flows in wire so don't worry about smd burned . Only you can use cotton & little amount of petrol and then just smoothly wipe the whole ckt and also clean the rotor ckt connection then fit tightly & correctly. In my thought this type of problems persist when the rotor contact is loose through the ckt. Thank you my brother & have a nice day.
My brother " Huevo peiscas " thank you again comment me. My brother please wright your problem in "English Language". Thank you my brother & Have a nice day.
Hi Nihar.. I watched all ur videos, Nice work. I have two multimeter One is from Orpat and other is from Mastech both have same problem. Showing auto reading even if not used and always shows 1 in DC voltage. Sometimes shows reading. Please help
My brother "Zubair Shaikh" first thing thank you for comment me. Main cause of this problem is due to weak smd resistor or burn smd resistor.My brother can you give all number printed number on smd resistor ,,like R16=103 etc ,, so I give you all resistor with appropriate color code. Thank you my brother & have a nice day.
@@kcdash9638 hi, i have same issue with my dt830d multimeter shows auto reading without probe, in buzzer range non stop buzzing. Help me to fix this. Thanks in advance
Bro I need a help to repair my digital multimeter DT830D Model.. Unfortunately DC High voltage entered in to it...it was not working.. i.e..No Display...I can't find anything burnt.. everything seens like good...what can I do...?
One of the display bar is always on in my multymeter The top of the third digit is always on When i measuew 1 vold in 20 section it shows 7 And 4 shows some odd But it is not display problem. When i keep the knob on buzzer it disappears. Please help Please
hi brother, i dammaged my multimeter by plugging 12v dc while it was set to 200uf capacitor position anw now it only displays "1" in all positions, can it be fixed ? thanks
My brother "nacer nait" No problem brother. Can you send me all smd resistor number printed on back side. Like 103 1037 like this.every meter has different smd resistor. Then I convert all resistor to big resistor with appropriate color code. Thank you my brother have a nice day.
My brother "Abdul Kasim"first thing thank you for comment me. My brother every meter have different smd restore but sometimes it may be work with few meter. I use two 1 meg resistant colour code is. Brown black green gold.
Hi my bro. My multimeter DC voltage 20v I connect battery 3.7 multimeter (20v) show 0.12 volt. Please how to repair DC voltage my multimeter? Please help my
My brother " Ramdayal Das " first thing thank you for comment me. My brother SMD 1000 Convert into big resistor it is a ,,,,,100 ohms Brown Black Brown Gold. For any thing more you can comment me. Thank you my brother & have a nice day.
A/C and D/C not working not correct reading. When D/C reading is taken lastly "1" is showing and A/C taken not show and come again "000".Please give solution which and No. and value of code in ohams or "K" to be changed. Thanks.
My brother "Sham phadnis" first thing thak you for comment me. My brother is your multimeter same to same like my meter ????? If not first i have uploade 4 meter repair videos first you see all videos ,,look care fully all videos ,,,,,After watching my all videos ......then comment me which one is matches with your meter . Then i give you appropriate Resistors with color code.
@@kcdash9638 You informed you have upload 4 meter repair videoed and sugested to see first, but will you please let me know how can see your first 4 videoes where to see at your Chanel or some other places. Thank.
My brother "Sham phadnis "thank you again comment me. Open youtube type nihar dash then click my photo you able to see all my videos.If problem then comment me. Thank you & Have nice day.
@@kcdash9638 Further to guidance and informed me to see your 4meters videoes. Seen the videos carefully. My DMM model is HAOYUE DT830D. The smd registers of this meter are shown below:- R1-514 R2-514 R3-1302 R4-3009 R5-224 R6-1000 R7-224 R8-1001 R9-514 R10-1000 R11-105 R12-2002 R13-1000 R14-1002 R-15-132 R16-1006 R17-9002 R18-9R00 R19-3523 R20-R990 R21-5483 R22-224 R23-224 and RY1-64R9. Please see the register numbers if anyone is wrong place change it. Please also give me code colour numbers. The problem is wrong readings are shown in LCD, A/C,D/C .I am sorry to trouble you, as I am senior citizen and I am very interesting in electronic repairs. Other request is that I have one other DMM DT830D UNITY model. In problem is full charged battery is connected but there is no display on LCD screen pl give your valuable guidance. Once again lot thanks.
I am a Newley appointed electronic engineering candidate. This little initiative of defective meter repair accomplished by me. Respected senior citizen sir,,,,, "Sham phadnis" the list of resistor with color code as per your concern. R1&R2=514 = 550K Green Green yellow gold. R3=1302=Brown Orange Orange Gold. R4=3009=300G Ohms no need to replace it its thoo high resistor. R5=224=220k Red Red Yellow Gold. R6=1000=100 Ohms Brown Black Brown Gold. R7=224=220k Red Red Yellow Gold. R8=1001=1k Brow Black Red Gold. R9=514=510k Green Brown Yellow Gold. R10=1000=100 Ohms Brown Black Brown Gold. R11=105=Brown Black Green Gold. R12=2002=20k Red Black Orange Gold. R13=1000=100 Ohms Brown Black Brown Gold. R14=1002=10k Brown Bkack Orange Gold. R15=132=1.3k Brown Orange Red Gold. R16=1006=100M Ohms No need to Replace. R17=9002=90k White Black Orange Gold. R18=9R00=9 Ohms use 10 Ohms Brown Black Black Gold. R19=3523=352k use 350k Orange Green Yellow Gold. R20=R990=990M Ohms.no need to replace high value . R21=5483=548k use 550k Green Green Yellow Gold. R22=224=220k Red Red Yellow Gold. R23=224=220k Red Red Yellow Gold. RY1-64R9=64k Blue yellow Orange Gold. Meter repair is time taken job just do it as a practical ,,,,,, My point of view if the display is work the meter is alwright. Try to find rare resistors/ohms in your old Tv & Radio Ckt. Thank you sir & Have a nice day.
My brother "Lahpati Parsu"first thing thank you for comment me. Mere bahi bo 10mega ohm ka tha ,,,Yun to ye kharb nahi hota par shayad moisture ya kisi Karn bas ye galat reading dikha Raha he to mere pas itne high ka nahi tha to Maine isme 1 meg ka 2 resistance Laga diya . Aur koi sawal hai to mujhe comment Kare. My brother have a nice day.
My brother " Chetan Sharma " thank you again comment me. If bad reading shows to aap apna R2 we Lekar R7 tak check karna hoga agar koi jala hua hai ya dry solder hua hai R2 jaise ki ye sirf serial number hai aasli number smd me upar likha hua hai to aap jise nikale uske upar Jo number likha hua hai ise mujhe R2 se lekar R8 tak jitne hain uske upar Jo number likha hua hai mujhe comment karna jaise ki R2=499 R3=559 Ise tarah we mujhe bheejo ....uske bad mein aap ko resistor color code ke sath bhejoonga....Thank you & have a nice day....
My brother first thing thank you for comment me. The problem is bad reading in Ohms reading & kilo resistor problem in multimeter. Thank you my brother & have a nice day.
Sir mujhase ek bhul ho gai jisase mera multimeter kharab ho gya resistivity mode pe rakhne ke bad ac bolt check karne se kharab ho gya please thik karne upay bataye
Chal raha hai aur ac volt shayd show karta hai aur diode mode par sound bhi de raha hai par resister anad dc volt check nahi ho raha hai dc volt mode par pahle se 3 4 6 volt show hote hai
My brother "Chetan Sharma " first thing thank you for comment me. Aagar aap ka SMD jal jaye to iske upar jo chota sa number hai isse aap convert kar ke aap big resistor with appropriate color code ke saath Laga sakte hain. Thank you my brother & have a nice day.
My brother "Er.Kumar" aagar voltage galat de ra ha hai to Aap r6ki jagah par 22ohms ki laga kar dekhe. Color code -- Red Red Black Gold. Thank you my brother & have a nice day.
My brother " Huevo peiscas " first thing thank you for comment me. I don't know your language but ,,,, I try your language pattern. Que tipo de resistance is 2×1meg - colour code ,,, Brown Black Green Gold. Thank you my brother & have a nice day.
My brother "VIRENDRA KUSHAWAH" first thing thank you for comment me. Kya hua hai aap ke display ko kya koi bhi letter nahi aaraha hai ya galat reading dikha raha hai ya aadha aadhoora aa raha hai Mujhe batao mere bahi .......... Thank you for comment me & have a nice day........
Thanks very much for your video
I had just damaged my DT830B by setting DCV and connecting to AC voltage.
I was going to throw it away when I disassembled and saw these tiny SMD components.
How to find the faulty one???
The I saw your video orienting to check the resistor and identifying the faulty one!!
I did the same and found a similar sign on one of the resistors, when checked it was faulty!
It was a 900 ohms.
I then removed it and replaced it with a 102 (very close) also SMD
The multimeter is back in business!
(It measures AC 10% higher though)
Thanks a lot my friend
Best regards
Bro which resistor u changed.. Can u help me.. My multimeter also ahows -1 problem..
@@AmanKhan-ec6lg Most certainly, my friend
I have looked for the resistor with signs of damage according to the orientation in this Vídeo. The resistor I found to be defective was the 9000 (900 ohms) I replaced it with another one that was available of 1000 ohms.
The result was good, because it started again to measure voltage, although with an increase of 10% in the read value. So I bought the right resistor (900 ohms) and replaced and now it is ok.
U can try to identify with a magnifier or u can measure with some other multimeter.
Best luck for u
Regards
Salu from Rio de Janeiro
i have some resistor show the lower value than the actual number showing on SMD
when i remove the smd n measure it the result is normal then i put back on the resistor
my multitester going erratically
no short circuit just after i change the new buzzer to the louder one then the problem happen
_BRAVO. SUPER._
I like this guy pure,silence but sure :-)
Patience is your victory very useful thank you bro
My brother "Anees Ahmed" thank for your support ,,, I make 93 videos ,,,, Hope that you may like also,,,,,
Many many thanks my brother & have a nice day.
Good luck sir
U R The Best
Good, BUT I cannot understand how you converted SMD code into Ohm? What I know it is 1200 M Ohm because:
128, a Three Digit Code, follows:
= 12 x (10 x 8) OR 12E8
= 1200000000 Ohm
= 1200000K Ohm
= 1200M Ohm OR 1200 Meg Ohm
Please correct me if I am wrong
Neither of your tested resistors gave accurate readings, the big 470 Ohm resistor you checked gave > 580 Ohm, why is that?
It's 1.2Gohm. u r right
Sir,
I have one DMM (HAOYUE DT830D).
Problems are as follows:
(1) Installed new battery
9 volts, the broblem is that inspite of fulled battery, in mode there is no display only dot is displayed ( Like (.) and on bugger/continue mode only (-1) minus one is displayed and slowly it disappeared. will you kindly give solution to what shall i check on PCB of DMM and why such problems are arised whether due to the fixed I.C.(Black) any bad components like Registors/diat/capacitors/bugger attachments.
Pl slove the prblems Sir.Thanks.
Your video is very interesting bro. . My multimeter DT-830D. By mistake I checked AC current when the red probe was inserted to 10A-DC. Now the multimeter display is there, but it is not reading AC or DC voltage or the continuity. Checked for any burnt SMD or other part, but could not find any damaged component. Can you pls advise me how to repair this multimeter Thank you.
very helpful. Thank you
Useful tips - thanks. It would be more attractive if audio is incorporated in the video.
আমি DT830D use করছি আমার ডিজিটাল মিটার মিলিআম্পিয়ার সেকশন নিলে অটোমেটিক রিডিং বাড়তে ba কমতে থাকে বাকি সব ঠিক আছে
কি সমস্যা হতে পারে একটু বলবেন !
Excuse me sir do you have the schematic for the exact same model? I'm trying to figure out the value of each smd capacitor especially the one that is located near the top left corner next to the big green mylar capacitor.
Nice video......keep it up........I have MECO 27 auto multi meter in it 230 AC voltage is showing 0 and some time it shows 70 volt not shows exact voltage so what's the issue please suggest........!!! What to do if this issue is inthis yellow Meter.....?????
My brother "Nicks Torc" first thing thank you for comment me .
My brother this type of clamp meter is used to detect the induction current flows in wire so don't worry about smd burned .
Only you can use cotton & little amount of petrol and then just smoothly wipe the whole ckt and also clean the rotor ckt connection then fit tightly & correctly.
In my thought this type of problems persist when the rotor contact is loose through the ckt.
Thank you my brother & have a nice day.
Display problem in my multimeter plz 1 video in display
Me parece bien tu trabajo
My brother " Huevo peiscas " thank you again comment me.
My brother please wright your problem in "English Language".
Thank you my brother & Have a nice day.
Hi Nihar.. I watched all ur videos, Nice work. I have two multimeter One is from Orpat and other is from Mastech both have same problem. Showing auto reading even if not used and always shows 1 in DC voltage. Sometimes shows reading. Please help
My brother "Zubair Shaikh" first thing thank you for comment me.
Main cause of this problem is due to weak smd resistor or burn smd resistor.My brother can you give all number printed number on smd resistor ,,like R16=103 etc ,, so I give you all resistor with appropriate color code.
Thank you my brother & have a nice day.
@@kcdash9638 hi, i have same issue with my dt830d multimeter shows auto reading without probe, in buzzer range non stop buzzing. Help me to fix this. Thanks in advance
Sir Please Send The Ma Value Of Capacitor.
SHYD 104 hai lakin ap phir b bta den?
Bro I need a help to repair my digital multimeter DT830D Model.. Unfortunately DC High voltage entered in to it...it was not working.. i.e..No Display...I can't find anything burnt.. everything seens like good...what can I do...?
Please check all the resistors with another multimeter and replace
Sometimes it is not possible to identify visually the faulty component
Thank u bro...thank you so much
One of the display bar is always on in my multymeter
The top of the third digit is always on
When i measuew 1 vold in 20 section it shows 7
And 4 shows some odd
But it is not display problem.
When i keep the knob on buzzer it disappears.
Please help
Please
hi brother, i dammaged my multimeter by plugging 12v dc while it was set to 200uf capacitor position anw now it only displays "1" in all positions, can it be fixed ? thanks
My brother "nacer nait" No problem brother.
Can you send me all smd resistor number printed on back side.
Like 103 1037 like this.every meter has different smd resistor.
Then I convert all resistor to big resistor with appropriate color code.
Thank you my brother have a nice day.
@@kcdash9638 bro mene multimeter se mosquito racket check to multimeter me problem ho gayi display nhi dikh raha kuch kaise thik kru.,
अगर साथ में बोल भी देते तो और better होता...👌
अगर जादा व्होल्टेज से उड गया हो तो रेपेर कर्नेमे पहिला पॉईंट konsa देखणा चाहीये
Sir Frequency not coming in clamp meter how to fix that problem
You can help repair ladder diodes no burn but no working, no buzz. Thank you.
Mere pas jo multimeter h usme b same problm h..pr jo smd burm ho geya uska number nai dikh raha..usko kaise thk krna h?
जूम करके जो आओ थिनर से साफ किये है,उन 5 रेजिस्टेंस के नंबर कोड क्रम से बताइए नीचे से ऊपर
Nice
200mA fuse blown up again & again,whenever I measure d.c. voltage or continuity.
Sir Voltage Galat Bta Raha Hai Koi Idea???
Can you tell me the value of capacitor. Sir please
My brother "Abdul Kasim"first thing thank you for comment me.
My brother every meter have different smd restore but sometimes it may be work with few meter.
I use two 1 meg resistant colour code is.
Brown black green gold.
Right bro
Bro can u add me in wp 7802043143
I need help about multimeter repairing.. please
Hi my bro.
My multimeter DC voltage 20v I connect battery 3.7 multimeter (20v) show 0.12 volt.
Please how to repair DC voltage my multimeter?
Please help my
I Found SMD resistor number 1000 then what is tha value of replaced resister.
My brother " Ramdayal Das " first thing thank you for comment me.
My brother SMD 1000 Convert into big resistor it is a ,,,,,100 ohms Brown Black Brown Gold.
For any thing more you can comment me.
Thank you my brother & have a nice day.
@@kcdash9638
You understand hindi.
Mere bahi " Ramdayal Das "aap Hindi me likh do aap ka problem aako solution mil jayega.
Thank you my brother & have a nice day.
A/C and D/C not working not correct reading. When D/C reading is taken lastly "1" is showing and A/C taken not show and come again "000".Please give solution which and No. and value of code in ohams or "K" to be changed. Thanks.
My brother "Sham phadnis" first thing thak you for comment me.
My brother is your multimeter same to same like my meter ?????
If not first i have uploade 4 meter repair videos first you see all videos ,,look care fully all videos ,,,,,After watching my all videos
......then comment me which one is matches with your meter .
Then i give you appropriate Resistors with color code.
@@kcdash9638 You informed you have upload 4 meter repair videoed and sugested to see first, but will you please let me know how can see your first 4 videoes where to see at your Chanel or some other places. Thank.
My brother "Sham phadnis "thank you again comment me.
Open youtube type nihar dash then click my photo you able to see all my videos.If problem then comment me.
Thank you
&
Have nice day.
@@kcdash9638 Further to guidance and informed me to see your 4meters videoes. Seen the videos carefully. My DMM model is HAOYUE DT830D. The smd registers of this meter are shown below:-
R1-514
R2-514
R3-1302
R4-3009
R5-224
R6-1000
R7-224
R8-1001
R9-514
R10-1000
R11-105
R12-2002
R13-1000
R14-1002
R-15-132
R16-1006
R17-9002
R18-9R00
R19-3523
R20-R990
R21-5483
R22-224
R23-224 and RY1-64R9.
Please see the register numbers if anyone is wrong place change it. Please also give me code colour numbers. The problem is wrong readings are shown in LCD, A/C,D/C .I am sorry to trouble you, as I am senior citizen and I am very interesting in electronic repairs.
Other request is that I have one other DMM DT830D UNITY model. In problem is full charged battery is connected but there is no display on LCD screen pl give your valuable guidance. Once again lot thanks.
I am a Newley appointed electronic engineering candidate.
This little initiative of defective meter repair accomplished by me.
Respected senior citizen sir,,,,,
"Sham phadnis" the list of resistor with color code as per your concern.
R1&R2=514 = 550K Green Green yellow gold.
R3=1302=Brown Orange Orange Gold.
R4=3009=300G Ohms no need to replace it its thoo high resistor.
R5=224=220k Red Red Yellow Gold.
R6=1000=100 Ohms Brown Black Brown Gold.
R7=224=220k Red Red Yellow Gold.
R8=1001=1k Brow Black Red Gold.
R9=514=510k Green Brown Yellow Gold.
R10=1000=100 Ohms Brown Black Brown Gold.
R11=105=Brown Black Green Gold.
R12=2002=20k Red Black Orange Gold.
R13=1000=100 Ohms Brown Black Brown Gold.
R14=1002=10k Brown Bkack Orange Gold.
R15=132=1.3k Brown Orange Red Gold.
R16=1006=100M Ohms No need to Replace.
R17=9002=90k White Black Orange Gold.
R18=9R00=9 Ohms use 10 Ohms Brown Black Black Gold.
R19=3523=352k use 350k Orange Green Yellow Gold.
R20=R990=990M Ohms.no need to replace high value .
R21=5483=548k use 550k Green Green Yellow Gold.
R22=224=220k Red Red Yellow Gold.
R23=224=220k Red Red Yellow Gold.
RY1-64R9=64k Blue yellow Orange Gold.
Meter repair is time taken job just do it as a practical ,,,,,, My point of view if the display is work the meter is alwright.
Try to find rare resistors/ohms in your old Tv & Radio Ckt.
Thank you sir & Have a nice day.
भाई साहब आप ने ये नहीं बताया की जो कम्पोनेन्ट निकाला वो कितने ओम का था please बताइए ना।
My brother "Lahpati Parsu"first thing thank you for comment me.
Mere bahi bo 10mega ohm ka tha ,,,Yun to ye kharb nahi hota par shayad moisture ya kisi Karn bas ye galat reading dikha Raha he
to mere pas itne high ka nahi tha to Maine isme 1 meg ka 2 resistance Laga diya .
Aur koi sawal hai to mujhe comment Kare.
My brother have a nice day.
sir ye kam karega
128 SMD RESISTER = 1.2GIGAOHMS
Sir R18 diode pr kitna likha h vo fart ho gyi h
Smd 128 2 mega ohm kaise ho geya?
Mene smd chenj kar diya uske bad bi ridding shi nahi dikha rha h uska kya karan h btaye Bhaiya
My brother " Chetan Sharma " thank you again comment me.
If bad reading shows to aap apna R2 we Lekar R7 tak check karna hoga agar koi jala hua hai ya dry solder hua hai
R2 jaise ki ye sirf serial number hai aasli number smd me upar likha hua hai to aap jise nikale uske upar Jo number likha hua hai ise mujhe R2 se lekar R8 tak jitne hain uske upar Jo number likha hua hai mujhe comment karna jaise ki
R2=499
R3=559
Ise tarah we mujhe bheejo ....uske bad mein aap ko resistor color code ke sath bhejoonga....Thank you & have a nice day....
actually what is the problem in multimeter
My brother first thing thank you for comment me.
The problem is bad reading in Ohms reading & kilo resistor problem in multimeter.
Thank you my brother & have a nice day.
Sir mujhase ek bhul ho gai jisase mera multimeter kharab ho gya resistivity mode pe rakhne ke bad ac bolt check karne se kharab ho gya please thik karne upay bataye
My brother " Prakash Gupta" kya aap ka meter ka display chal raha hai ya nahi aap mujhe comment kijiye ...............................
Nihar Dash chal raha hai
Chal raha hai aur ac volt shayd show karta hai aur diode mode par sound bhi de raha hai par resister anad dc volt check nahi ho raha hai dc volt mode par pahle se 3 4 6 volt show hote hai
Kya aap mujhase call karke bat karna chahte hai to mera mo. No. 6264495630 hai aur whatsapp par chatting bhi kar sakte hai
Sir but i am not understand english please talk in english
Multimeter ka smd kharab ho jaye to kya karna chahi ye
My brother "Chetan Sharma " first thing thank you for comment me.
Aagar aap ka SMD jal jaye to iske upar jo chota sa number hai isse aap convert kar ke aap big resistor with appropriate color code ke saath Laga sakte hain.
Thank you my brother & have a nice day.
Camera bhi change sey nahi rakha aour na hi sound h kia yeh gounga h jo awaz nahi aa rahi h.
voltage galt ha. multimeter me
help me
My brother "Er.Kumar" aagar voltage galat de ra ha hai to
Aap r6ki jagah par 22ohms ki laga kar dekhe.
Color code -- Red Red Black Gold.
Thank you my brother & have a nice day.
El A830B como se repara
Que tipo de resistencias
My brother " Huevo peiscas " first thing thank you for comment me.
I don't know your language but ,,,, I try your language pattern.
Que tipo de resistance is 2×1meg - colour code ,,, Brown Black Green Gold.
Thank you my brother & have a nice day.
@@kcdash9638 las resistencias tienen lineas de colores
@@kcdash9638 yo tengo una placa igual tiene tro numero
me kese thik karoo
mere multimeter me display problem hai
My brother "VIRENDRA KUSHAWAH" first thing thank you for comment me.
Kya hua hai aap ke display ko kya koi bhi letter nahi aaraha hai ya galat reading dikha raha hai ya aadha aadhoora aa raha hai
Mujhe batao mere bahi ..........
Thank you for comment me & have a nice day........
Mere multimeter number aa kr kat ja raha h
What a lag vrdio man..
Apna n. Do