Could you please tell me how you manage to slide the right side fairing back into place? I've been trying for 2 hours with my bike and have had no luck. I cannot get the 2 tabs at the front of the mid fairing to slide into place. Thanks.
I really liked your video to disassemble the bike and be able to put on the circuit fairing, thank you very much, Regards Realmente me ha venido genial tu video para desmontar la moto y poder poner el carenado de circuito , muchas gracias , Saludos desde España .
I’ve noticed even with all screws removed it’s like it still does not want to come off. It looked like when you pulled it made a pop. I fully understand the top front part but is there something in the rear area that is fastened by some kind of friction post that pops out?? I was only partly disassembling mine due to the previous owner not having the front tabs in right and was able to fix it without fully removing the whole piece. Just looking for info for future reference. My R1 fairings are so much easier.
Just bought a 2007 R1 (same plastic as a 2008) and this thing is a PITA! I have some Allen/Zeus bolts, plastic push-pins, and regular Allen bolts. For plastic, both red and black side panels, the upper black cowl plastic above the fender, the lower "V" , then of course the other side (rh) if you need to drain or fill coolant. Not to mention the red bottom cowl if you want most of it out of the way. This still is not counting the side panels near the ram-air ducts if you ever need to get under them! I think it's a beautiful bike, but maybe should have bought an old FZ1 instead! What year is your R1 that is so easy to work on?
Could you please tell me how you manage to slide the right side fairing back into place? I've been trying for 2 hours with my bike and have had no luck. I cannot get the 2 tabs at the front of the mid fairing to slide into place. Thanks.
We miss you already Iron!!!!!
smh, lol
just want to say thank you, this vid helped me tremendously !
finally i waited for this moment ha!!! lol #nosleep
Hey bro mind share how do you install those mid/lower fairings ? I found its hard i had to remove the ram air manifold instead 😆
😱 the 883 is still there this is older then the last video lol
NightOwl yes it is going down memory lane 😍😢
Are you planning on doing an exhaust video?
Yup! Recorded and scheduled, should be out next week :)
Does the duct fit under or above the rubber sheet that is laid below the tank...?
We’re those OEM fairings? I’m looking for that matte black/grey look for my r6. Any aftermarket recommendations?
Cheers mate, i'd be helpful if u would tell me the l paint code of this grey matte?
what frame sliders do you have? i want the exact same ones. we have the same bike to the tee.
Very good explanation. Thank you
I really liked your video to disassemble the bike and be able to put on the circuit fairing, thank you very much, Regards Realmente me ha venido genial tu video para desmontar la moto y poder poner el carenado de circuito , muchas gracias , Saludos desde España .
Thanks for the vid! Still trying to build the confident to take my fairing off 😂 I'll break some shit
Have been thinking about wrapping my fairings as well, out of curiosity how much did it cost you?
"HEY YOU DONT SAY THAT" lol
Thanks man 🤙🏽
videos on Yamaha R6 OBD2 code diagnosis info fault reset
I’ve noticed even with all screws removed it’s like it still does not want to come off. It looked like when you pulled it made a pop. I fully understand the top front part but is there something in the rear area that is fastened by some kind of friction post that pops out?? I was only partly disassembling mine due to the previous owner not having the front tabs in right and was able to fix it without fully removing the whole piece. Just looking for info for future reference. My R1 fairings are so much easier.
Just bought a 2007 R1 (same plastic as a 2008) and this thing is a PITA! I have some Allen/Zeus bolts, plastic push-pins, and regular Allen bolts. For plastic, both red and black side panels, the upper black cowl plastic above the fender, the lower "V" , then of course the other side (rh) if you need to drain or fill coolant. Not to mention the red bottom cowl if you want most of it out of the way. This still is not counting the side panels near the ram-air ducts if you ever need to get under them! I think it's a beautiful bike, but maybe should have bought an old FZ1 instead!
What year is your R1 that is so easy to work on?
do you wear your helmet when you do tutorials?
rSANTOSx00 it's better to be protected
No way, it'd be hot as hell in the garage with a helmet, haha. I've got my GoPro and a mouth mount - amzn.to/2uiRJMm
just kidding, great video.
Poor lil iron. . Little did it know that after this it would be stripped of its upgrades and pimped out lol.
The only thing it was stripped of was it's seat and swingarm bag, lol. Whoever bought it got everything else.
Every piece that came off popped and I thought you broke it. Always scares me when I work on these plastic parts.
Thanks for not blasting your face on the whole video.
That’ll piss a lot of people off 😂. Nice video! Very detailed.
I hadn't noticed the front turn signals before... dem schitts ugly.
Dem schitts gone! :D
R6 2016?
I really thought you said "***k heads". Haha
I tend to break tabs and anything that’s plastic which means I’ve got to pay someone to take my fairings out ugh 😢
1st
Shits weak B-rye!
Jon FZ09 1 way or another i had to be 1st now im fucked bcuz im tired af to chill in disney today
reaching for content now lol
Really? Far from it. I DIY / make a "How To" videos out of pretty much anything I do to the bikes, doesn't matter which bike. See the playlists.