Hey just want to say thank you I got my arduino yesterday and was able to get 4 esc working again at first I kept getting a message saying check power connections but I changed the order of d2 and d3 and it worked I almost threw these esc out a while ago I'm so glad I didn't
+Dave stints oh awesomeeee!!!!!!! And thank you for reminding l, I have some to work on for a friend loloool that’s awesome brother, glad ya didn’t waste em. Were they by chance dys esc’s??
Just tried this after finding 4 bricked LittleBee 30A-S ESC'S. It worked a treat, I did have to swap TX and RX for it to work but great. A big thank you from across the pond.
Hi, thanks for the knowledge awesome video! Ok I have a couple of questions: 1) I have replaced three STM32 micros on a chinese 4in1 so they are blank and not showing up in BLHeli suite so as there are four pads on the ESC for each of the micros I’m hoping I can use your method to flash them individually. So does the micro boot loader get flashed to the chip by the Arduino or is it just the operational code? 2) Are all ESC pad configurations the same i.e gnd, nc, data, data?
Wow that’s so cool! I found the pads and the ground using your trick (it was unlabelled), I’ll try to set it up with 1-wire interface but if that doesn’t fly, I’ll go with your setup -your soldering looked hard so I wanna try with less soldering using the 1-wire interface if possible… Fingers crossed! Thanks again, this was super helpful!
i did exactly same way i didn't succeed/GND and 2 pads near.(same arduino) esc diferent have no idea what kind... but esc conected to motors and fc. maybe some advice?thank you . P.S/ there is also other pads on esc
Oh man, you just saved me $40!!! Thank you so much!!! BTW, I wasn't able to follow which order the other two wires besides ground went, so I had to try both ways before I got it to work.
Great video. Were you able to do a video for the DYS 4in1 ESC? I can't find the pads to connect to on the 4in1. Can you please tell me where to solder? Thanks
Hello there! I got a 4in1 Mamba ESC and if I connect it to Blheli_32suite the program only reads one esc.. But sometimes a second ecs gets recognized as well, could this be a software problem?
flux is cheap! nice video, I am going to purchase some arduino nanos right now (still watching to see if this is still relevant in 2021, first) I have literally a handful of AOI whoop boards that have 1 or more motors that dont work (all happymodel AIO's)
Hey buddy, i accidentally flash wrong esc type onto my esc. Supposed my esc code is A-H-30 for example, all 4 esc were spinning with jittering like hell, so i purposely flash my esc with other esc code such as A-G-30 (STUPID) for example, (i forgot what code that was) then now i want to revert back to my old stock, can i use this method?
Yes 2 of them were dys the other 2 were Diatone I ordered a replacement 30a esc from Diatone for my Gt2 and the one they sent me had no heat sink and it wouldn't recognize in blheli I sent them like 10 emails about it and they never replied what great customer support needless to say I won't be buying anything from them again
+Primo Cruz fucking a baby. All five are fixed and rocking!!!! After I used the arduino I hooked them all up to a pdb and an omnibus fc to make sure they r good. Wala perfect. They are all set. All u have to do when u use them is get into blheli suite to make sure the directions are right.
Hey I used your Banggood link and it worked fine but they only ship from China but they have another nano board but it says it's an upgrade version of this says it has a better USB chip what ever that means do think it's ok to get that one because it ships from Us warehouse
Hey buddy, I reached out to you about that 4in1 hglrc that was only showing 2 ESC’s ! I was wondering if I could send you mine to fix if you don’t mind I will pay for your service if you want. Great vid by the way!
+SteveO4478 no problem STEVE. I have an hglrc our in the shop actually. Your more than welcome to send it to me and I’ll try to fix it for u. But I’m not taking any money. Next week I am on vacation, so it might be next Thursday before I can get to it. Email me and I’ll send ya my address jasongjamiel@gmail.com
Great Vid! I just bought some DYS XSD 3a ESCs........one of them is giving me trouble. I get no tone out of one of them when i connect my battery....however the led on the esc is on. BLHELi does not see it at all......i will try your method....i hope it works. I hate paying money for something that doesn't fucking work!
Worked like a champ! I did have to swap D2 and D3 comm pads but none the less.....fixed. Hell Yes! Thanks again brother! Now im going to have a glass of whisky like a real man...lol
Hit on everyone ,when I connect to the lipo It says Esc failed I don't get any lights on the esc .I do know that 2 of the 4 esc's are fine I did write to you explaining when I tried to flash it failed and caused the esc not to be found in blheli Just to make sure I connected the first pad to earth, I missed 2 pads soldered signal to the 4th As you say earth first one Miss a pad then d2,d3 that would make it the 4th
try this fix....this worked on 4 impossibly bricked esc's. take your bricked esc open it/them with the Atmel Cleanflight interface then after BLH says its expecting SILabs open the SL interface and then click on Options -->EXPERT MODE then use EXPERT TOOLS--> FLASH ANY FILE . perhaps the bircked esc has the file locked or just not closed right the Atmel interface opens your ecs to read and write sees its not the one it wants and sorta leaves the door open allowing you to flash with the right SILabs interface....?? heres a music suggestion for you "When the work is over" by the Kinks www.google.com/url?sa=t&rct=j&q=&esrc=s&source=web&cd=1&cad=rja&uact=8&ved=0ahUKEwittvabus7ZAhVnr1QKHeSmAY0QyCkILDAA&url=https%3A%2F%2Fwww.youtube.com%2Fwatch%3Fv%3DuIOtTpF9R3I&usg=AOvVaw3l1AGPB_xQZtsbnv86E-Yj
Saweeeet I will try that. I haven’t had any issues with bricked esc’s myself. Seems like it’s always friends that had the issue and it was mostly on dys esc’s oddly. Great trick brother, I’ll try this next time
also just in case heres a link to the usb driver for the ch340 chip in the Geekcreit® ATmega328P Nano V3 Controller Board that you have linked..... arduino-info.wikispaces.com/file/view/CH341SER.EXE/561162321/CH341SER.EXE
Crap....you mean I could have just used my Arduino nano ? Thanks for that. All the other Kwadtubers are saying I need to get an FTDI FT232RL USB to TTL Serial Converter Adapter......so ordered one from Ebay store (supposedly Australian local store) and 4 weeks later still no adapter so ended up biting the bullet and got 4 new esc's. Obviously coming from china.....lots of chinese scammers claiming to be local now on ebay. Turns out that the corruption was coming from my Sirius Airhero F3 FC everytime I plugged it in passthrough mode to BLheli ......BAM!......no more bootloader. Will try to fix my bricked ones tonite using the Arduino nano. Cheers :).
Some people just makes stuff up without fully verifying it, for hobbyists generally working with RC stuffs dont need that plus it makes thing complicated. But the cool part is, arduino nano already comes with a built in FT232 (FTDI) interface, u can see the FT232 IC underneath board. So u buy one and get two or even more :3 besides, being embedded in an arduino makes it easier to install drivers in windows and stuffs. However, its been a year since this comment, we are in the future now! flashing blheli with FC pass-through and stuff. Still, sometimes it may come in handy, just like i needed tp do on a 4in1 blheli 32 couple weeks back; as the bootloader was too jammed up and needed a harder push i guess
I have the DYS 4in1 30A ... would you know which pins I connect to? Would really appreciate your help
is this through BLHeli suite also possible for BLS esc or only BL32 esc?
I was wondering if you could get a Hobby wing 200 Amp v4 ESC to work like this
Hey just want to say thank you I got my arduino yesterday and was able to get 4 esc working again at first I kept getting a message saying check power connections but I changed the order of d2 and d3 and it worked I almost threw these esc out a while ago I'm so glad I didn't
+Dave stints oh awesomeeee!!!!!!! And thank you for reminding l, I have some to work on for a friend loloool that’s awesome brother, glad ya didn’t waste em. Were they by chance dys esc’s??
Just tried this after finding 4 bricked LittleBee 30A-S ESC'S. It worked a treat, I did have to swap TX and RX for it to work but great. A big thank you from across the pond.
Bammmmm awesome!!!!!! I’m glad it worked for u
Hi, thanks for the knowledge awesome video! Ok I have a couple of questions: 1) I have replaced three STM32 micros on a chinese 4in1 so they are blank and not showing up in BLHeli suite so as there are four pads on the ESC for each of the micros I’m hoping I can use your method to flash them individually. So does the micro boot loader get flashed to the chip by the Arduino or is it just the operational code?
2) Are all ESC pad configurations the same i.e gnd, nc, data, data?
Wow that’s so cool! I found the pads and the ground using your trick (it was unlabelled), I’ll try to set it up with 1-wire interface but if that doesn’t fly, I’ll go with your setup -your soldering looked hard so I wanna try with less soldering using the 1-wire interface if possible… Fingers crossed! Thanks again, this was super helpful!
any danger in mixing d2 and d3?
Dos this work on an aio whoop type board such as a darwin tiny ape aio board?
Hey man, I have a T motor F45a v1, ESC 2 is fucked. Any idea how I can go about doing this?
i did exactly same way i didn't succeed/GND and 2 pads near.(same arduino) esc diferent have no idea what kind... but esc conected to motors and fc. maybe some advice?thank you .
P.S/
there is also other pads on esc
Any ideas on how to unbrick Lumeniere 12A SimonK AutoShot N-FET.
Oh man, you just saved me $40!!! Thank you so much!!!
BTW, I wasn't able to follow which order the other two wires besides ground went, so I had to try both ways before I got it to work.
+Gulzaar FPV awesome!!! But u got it working yes??
JJRotoGeek yeah, it's working on the Bench. Gonna take it out tomorrow.
+Gulzaar FPV awesome. Keep me posted
Im stuck with this error. What to do? Any idea? Avrdude FAILED stk500_getsync():not in sync:resp=0x00
Hi can you explain the procedure for 4 in 1 esc? I can't figure out what pads to solder to the bottom of the board. I have DYS 30a 4n1. Thx
+BnP Productions sure brother. Shoot me the link to the exact one u have
you ever get a fix for that 30A DYS ESC?
Great video. Were you able to do a video for the DYS 4in1 ESC? I can't find the pads to connect to on the 4in1. Can you please tell me where to solder? Thanks
Hey brother. No I haven’t. I avoid dys lol. Email me a pic of the bottom of the esc and I’ll see if I can work it out for ya
Thanks for your response. Can you please give me your email address? Thanks
Yes sir. Jjrotogeek@patriot-blades.com
I have the dys 4in1 30a ... which pins do I connect to?
Hello there! I got a 4in1 Mamba ESC and if I connect it to Blheli_32suite the program only reads one esc.. But sometimes a second ecs gets recognized as well, could this be a software problem?
Woaw, still good, thank you very much for this great tuto, you save my esc !!
Yayay!!!! That’s awesome
Great video man!!
Just wondering, can I do this on an esc that's not working after a crash?
+rumi geiger hmmmmm. If it was a crash it is probably a hardware problem. Does it beep when ya pug it in??
flux is cheap! nice video, I am going to purchase some arduino nanos right now (still watching to see if this is still relevant in 2021, first) I have literally a handful of AOI whoop boards that have 1 or more motors that dont work (all happymodel AIO's)
Hey buddy, i accidentally flash wrong esc type onto my esc. Supposed my esc code is A-H-30 for example, all 4 esc were spinning with jittering like hell, so i purposely flash my esc with other esc code such as A-G-30 (STUPID) for example, (i forgot what code that was) then now i want to revert back to my old stock, can i use this method?
+AFIQ aFaT yes u can. But really u should be able to just flash them back normally through blheli suite. Are they not showing up?
Still helpful in 2019!
Lol awesome!!!!!
Yes 2 of them were dys the other 2 were Diatone I ordered a replacement 30a esc from Diatone for my Gt2 and the one they sent me had no heat sink and it wouldn't recognize in blheli I sent them like 10 emails about it and they never replied what great customer support needless to say I won't be buying anything from them again
+Dave stints I hear ya. But I have fixed quite a few of these dys 30a for some people. Seems to be an issue
I have been trying this for 2 frigin days ,watching Blue falcon and cant get it to work So tom ,will give this a go
+spooner Graham awesome. Lemme know if ya need a hand
I am having problems sending you mail. Had it back 2 times, Please let me know if you get them Cheers, Gray
+spooner Graham gottem brother. Check ya mail
Thank you! Worked exactly like you said on Tyro79 4 in 1 ESC. Have to switch data cables 1 time but now its fixed and I can fly again! THANK YOU
will this work with blheli_32?
Bam, baby, looks like Xmas. 🤙
+Primo Cruz fucking a baby. All five are fixed and rocking!!!! After I used the arduino I hooked them all up to a pdb and an omnibus fc to make sure they r good. Wala perfect. They are all set. All u have to do when u use them is get into blheli suite to make sure the directions are right.
awesome, you da man
Hey I used your Banggood link and it worked fine but they only ship from China but they have another nano board but it says it's an upgrade version of this says it has a better USB chip what ever that means do think it's ok to get that one because it ships from Us warehouse
+Dave stints if ya can Dave, shoot me the link and I’ll double check it for ya
Hey buddy, I reached out to you about that 4in1 hglrc that was only showing 2 ESC’s ! I was wondering if I could send you mine to fix if you don’t mind I will pay for your service if you want. Great vid by the way!
+SteveO4478 no problem STEVE. I have an hglrc our in the shop actually. Your more than welcome to send it to me and I’ll try to fix it for u. But I’m not taking any money. Next week I am on vacation, so it might be next Thursday before I can get to it. Email me and I’ll send ya my address jasongjamiel@gmail.com
+SteveO4478 hey brother, did u get my email address???
JJRotoGeek no I didn’t.
+SteveO4478 crap. Jasongjamiel@gmail.com. Shoot me an email and I’ll send u my address
JJRotoGeek awesome !
Beautiful
Very useful!
+688755 🤘🤘🤘🤘🤖🤖
Great video thank u
Welcome!!!!
Good luck it’s a pia
Great Vid! I just bought some DYS XSD 3a ESCs........one of them is giving me trouble. I get no tone out of one of them when i connect my battery....however the led on the esc is on. BLHELi does not see it at all......i will try your method....i hope it works. I hate paying money for something that doesn't fucking work!
I hope it works for u to brother. Seems like I have a lot of people asking me for help with the dys esc’s. Seems to be an issue with them
Thanks for the reply!
Awesome!!! And let know how it goes brother
Will do!
Worked like a champ! I did have to swap D2 and D3 comm pads but none the less.....fixed. Hell Yes! Thanks again brother! Now im going to have a glass of whisky like a real man...lol
Hit on everyone ,when I connect to the lipo It says Esc failed I don't get any lights on the esc .I do know that 2 of the 4 esc's are fine I did write to you explaining when I tried to flash it failed and caused the esc not to be found in blheli
Just to make sure I connected the first pad to earth, I missed 2 pads soldered signal to the 4th As you say earth first one Miss a pad then d2,d3 that would make it the 4th
+spooner Graham hey my friend. What model of esc are you playing with? I’ll look into it.
They are the Diatone 302x Off the Tyrant S
+spooner Graham k let me do a little research
+spooner Graham ohhhh those are kiss esc’s??
+spooner Graham could u email me a picture of the back side of the esc so I can see the connections? Jasongjamiel@gmail.com
Getting on this now, fingers crossed it works for me
+spooner Graham 🤞👍👍👍
try this fix....this worked on 4 impossibly bricked esc's.
take your bricked esc open it/them with the Atmel Cleanflight interface
then after BLH says its expecting SILabs open the SL interface
and then click on Options -->EXPERT MODE then use
EXPERT TOOLS--> FLASH ANY FILE .
perhaps the bircked esc has the file locked or just not closed right
the Atmel interface opens your ecs to read and write sees its
not the one it wants and sorta leaves the door open allowing you to flash
with the right SILabs interface....??
heres a music suggestion for you "When the work is over" by the Kinks
www.google.com/url?sa=t&rct=j&q=&esrc=s&source=web&cd=1&cad=rja&uact=8&ved=0ahUKEwittvabus7ZAhVnr1QKHeSmAY0QyCkILDAA&url=https%3A%2F%2Fwww.youtube.com%2Fwatch%3Fv%3DuIOtTpF9R3I&usg=AOvVaw3l1AGPB_xQZtsbnv86E-Yj
Saweeeet I will try that. I haven’t had any issues with bricked esc’s myself. Seems like it’s always friends that had the issue and it was mostly on dys esc’s oddly. Great trick brother, I’ll try this next time
also just in case heres a link to the usb driver for the ch340 chip in the
Geekcreit® ATmega328P Nano V3 Controller Board
that you have linked.....
arduino-info.wikispaces.com/file/view/CH341SER.EXE/561162321/CH341SER.EXE
Bam 🤘🤘🤘thanks bro
Crap....you mean I could have just used my Arduino nano ? Thanks for that. All the other Kwadtubers are saying I need to get an FTDI FT232RL USB to TTL Serial Converter Adapter......so ordered one from Ebay store (supposedly Australian local store) and 4 weeks later still no adapter so ended up biting the bullet and got 4 new esc's. Obviously coming from china.....lots of chinese scammers claiming to be local now on ebay. Turns out that the corruption was coming from my Sirius Airhero F3 FC everytime I plugged it in passthrough mode to BLheli ......BAM!......no more bootloader. Will try to fix my bricked ones tonite using the Arduino nano. Cheers :).
+M.J.McRae Macka awesome!!! I’m sure you can use an ftdi in some way, I have one but opted for the board. Bammm simple. Let me know if u need a hand
Some people just makes stuff up without fully verifying it, for hobbyists generally working with RC stuffs dont need that plus it makes thing complicated. But the cool part is, arduino nano already comes with a built in FT232 (FTDI) interface, u can see the FT232 IC underneath board. So u buy one and get two or even more :3 besides, being embedded in an arduino makes it easier to install drivers in windows and stuffs.
However, its been a year since this comment, we are in the future now! flashing blheli with FC pass-through and stuff. Still, sometimes it may come in handy, just like i needed tp do on a 4in1 blheli 32 couple weeks back; as the bootloader was too jammed up and needed a harder push i guess
Awesome brother let know how it goes!
Don't flash your ESC's with low battery 🙂
suksma from bali
This is firmware. Not a bootloader. Haha...