วีดีโอ

Where can we find the STL file for the nose piece? Thanks in advance!

What brand hull is that I bought the exact one but missing the top cowling cover

Hello bro. 1 doubt regarding flex shaft. My nitro engine rotates in CCW direction. Then what type of flexible shaft should I select. 1)Left/Positive Or 2)Right/Negative

Where can I buy that motor and pipe new?

Excited to be joining the zippkits community!!

update?

can you make a video on how to install the killswitch? not fail safe, the killswitch on that same engine

How do you like the radio link transmitter and receivers. I have been wondering about them compared to Spectrum transmitters cuz my hobby shop does have radio link what is your take on it

Picked up a super clean XLB with Pro-Line Racing 1075-00 Masher 3.2" All Terrain Tires for $70. Threw in a new hi torque steering servo and a red cat racing head button and pull start. Cant wait to unlessh this beast

JJ which is the link for the discord group?

😂

HEY!!! when you gonna run this boat??? I want this boat...lol

I run ethanol pump gas which will damage the carb diaphram. so I start the engine and pinch the fuel line to get all the fuel out of the system.

What I do is run WD-40 through the gas line inlet going through the carburetor and into the motor and I've done that with great success as well also what size fuel bag are you using. I also use the electric spray to spray down my motor as well cleans it up really good and quick degreases it

Reprentin the brands. Thank you sir.❤

JJ my man!

In the past I ran a clutch with a square drive. Now I’m looking at adding. Clutch with a round Collett. So it’s my understanding, on square drives, the boat is pushed from the strut/ stinger. On a round collett, the boat is pushed against the collet, whether it’s on the motor or in this case a clutch. Is that right?

Hello I’m redoing a vee hull that has a stinger, first boat with a stinger. when I removed it I noticed the hole was drilled a few mm to the right, I read this was to help with prop walk. So my question is, if the stinger is offset and square on the transom, engine is centered in the rails, wouldn’t that mean my stuffing tube will have to be curved and have a slight S bend to meet the stinger?

Are used magnetic switches there is a few different brands

3 weeks and nothing? I guess chuck n chat is dead.

Im stuck with this error. What to do? Any idea? Avrdude FAILED stk500_getsync():not in sync:resp=0x00

Looks fun

You mentioned in one of your videos that you'd love to find a skiff kit. RCB kits out of the Netherlands has them, I think they are around 229 for the full kit. I bought from them before and it wasn't bad, slightly higher for the shipping. I bought the fooling racer flat bottom short kit from them.

I just do not likew electric. Thiem to run is short even with brushless. I have nitrro and gas engines in the boats , trucks and planes. IT is 5 to 7 min for electric or 15 to 30 min for nitro and gas. No brainer for me lol.

I have what I think is an old design 3.5 I also have one with a carb butterfly , however this is just a carb wide open design and then a plate that slides in and out at the exhaust port. THis is how it regulates rpm. DO you know of these and where to find more on them? So far have not had much luck finding this one. Thanks

Flat calm water SUCKS for a flat bottom! Need a little chop. Grew up racing flat bottom real boats... lol. Outboards tho... Love them, but always wanted to deck ride in a skiff

What type of remote starter are you using ? Great Video !

Great vid mate sweat boat, love ya lake, ya lucky bugger ,when is the invite for a BBQ 😂

Good Chuck & Chat Brother. Keep the dry side up..

D*** JJ you're lake is so sweet And right behind your house.What could be better for someone that likes boats

Are all the zenoah engines thr same where the collet will attach to the motor? Ive seen a few different things on the market, but every video i see the collet is attached to the motor shaft. Ive seen clutches, ones with a belt pulley. And ones with just the collet. Whsts the best approach? Im not sure i want to use a clutch.

Boy did this video bail me out. In particular was the part about flooded engine. Purposely flood engine and did exactly what you showed and now have confidence clearing out the engine. Putting in the plug 1/3 of the way was surprising. Thanks again my friend!

I have an Ez VEE I could never get right. I used this set up and changed the prop and the boat took off. My granddaughter uses this boat and has a ball with it. She will be racing next season. Thanks for the video. 😅

Thanks so much for this video. I now have fail safe on all my boats and I know how to use it thanks to you. Great video!! You’re the MAN!

JJ what is your discord link?

I learned you absolutely can over clamp a boat and distort the chines. no bueno.

Are the engine mounting holes pre drilled on these kits?

What a dick..your a bad example of a rc hobbyist.

I need the back story to what and how they set off jj 😅😅🤣🤣

What I'd ken and Matt don't get sarcasm 🤣🤣🫡

I want the go ped. Lol

Hahaha 😂😂😂

Sweet mother of Mary JJ.....No worries i responded

Something got you all WOUND UP or BENT OUT OF SHAPE with Ken and Matt. I’m dying laughing here. My question is “What Ya On?” That’s what I want to know. LOL.

did you call us all fuck sticks??? wtf will never watch you again

You hit the nail on the head with those 2 fuckers!!!

Bro that's sweet!! Did you dip it?

Sweet ride!!

Nice Rack!