Dismount Sam module Mercedes Viano

[@yllsonmici6610]

Hello Rick! I have fixed a new SAM on my van and I need to know if the sam does need programming. Thanks

[@rickstevens2941]

If Everything Works Fine It Is Not necessary but if There are Troubles then I would program It If I were you just try and see 🙂

[@maxramirez2582]

Tengo un 97 bravada no le prende las luces adelantera que debo hacer

[@marcomarco6819]

Hello Rick, If I want to facelift to Bi Xenon I just change this SAM and Xenon light units ? Do I have to purchase new harness?

[@rickstevens2941]

I don't know, the dealer can tell you that instandly. Have a nice day greetings From Holland 👍🏻😎👍🏻

[@MrAngi84]

Hallo Rick,
Ik zit met een verlichtingsprobleem bij mijn Vito W639. Het linkse dimlicht werkt niet meer. Krijgt geen voeding. Rechtse kant werkt perfect. Wat denk jij? De Sam-Module vervangen?
Grtz Angelo

[@rickstevens2941]

Kan ik zo niet zeggen,
Ik weet ook niet precies hoe het schema loopt maar als ik het ontworpen zou hebben zo denk ik dan meestal maar dan zou ik dat via twee relais laten lopen en dan moet je dus gewoon de stuur draad vanaf de Sam Module nalopen.
Als rechts een massa krijgt en links niet, zou je tijdelijk de stuur draad van het dimlicht links bij aan de rechter kunnen knopen, gaat dan links ook branden dan is de Sam inderdaad de oorzaak...

[@deanraffie1745]

I have n problem with my left side indicator it stays on outside van bt blinks in vito its 115 cdi 2007 Dean South Africa what is the cause of indicator light staying on thanks Dean South Africa

[@rickstevens2941]

Hi Dean: replace the part and your problem will 99% sure be fixed 😉 and be Blessed 👍🏻
( in this case the high side driver is shorted )

[@deanraffie1745]

@@rickstevens2941 I thank u what part must I replace Dean

[@deanraffie1745]

Hi I would like to knw where is the 10N relay thanks Dean South Africa

[@rickstevens2941]

Sorry For My late response.

[@mregory]

Hey thanks for the video, do you know if this Sam module controls the turn signals?

[@rickstevens2941]

Sorry For My late response depends on Which Turn Signal

[@mregory]

@@rickstevens2941 thanks very much for the reply. It is the left turn signal. The green left arrow flashes quickly on dashboard indicating that there is a fault and none of the left turn signal lights flash on the exterior of the van. Thanks again for your help 🙏

[@rickstevens2941]

Yes than there is a hi side Driver in de Sam module Broken see mij other clip on youtube th-cam.com/video/h8yobIZ2AWo/w-d-xo.html
This is Sound of the same Problem but it's not a Vito

[@rickstevens2941]

I think this Will leed you in the right Direction: th-cam.com/video/h8yobIZ2AWo/w-d-xo.html

[@mregory]

@@rickstevens2941 Thank you very much for your reply. I just watched the other video you suggested. I think this is just for the turn signal at the front of the van? The problem with my Vito van is. that all of the turn signal lights are currently dead on the left side (back, side and front) of the van. Will this component solve this issue? Also does this component plug in to the SAM module? Sorry for all of these questions, I really am very grateful for your help.

[@istvanszakal9813]

Hello. I have an error code u0423. Which module could be at fault? it will scramble all the sensor circuits on the engine.

[@rickstevens2941]

Sorry i don't know,
First thing to do is: check The Car with Star diagnostics..
That's the best entry to go.
Good Luck. 👍🏻

[@istvanszakal9813]

@@rickstevens2941
U0423
Invalid Data Received From Instrument Panel
Control Module
ha ezt jól értelmezem akkor a motorvezérlőtől nem kap a műszerfal megfelelő adatokat. Vagy a müszerfal nem jó és nem tudja feldolgozni az információt.

[@istvanszakal9813]

U0423
Invalid Data Received From Instrument Panel
Control Module
if I understand this correctly, the dashboard does not receive the correct data from the engine controller. Or the dashboard is not good and cannot process the information.

[@erikjoesaar2506]

Hi Rick
I cant get my rear window heatong working, the yellow light on the button does not come on.
When I use my delphi diagnostic tool to engage relay it clicks like its is suposed to. When I measure voltage from the fuse terminal, there is no voltage there and when I put + side directly to fuse terminal nothing changes.
Do you have any ideas?
Best wishes
Erik

[@erikjoesaar2506]

Adding to that, when I am diagnosing the sam module with diagnostic tool, the light on button works, butnitnstill doesnt engage the relay

[@rickstevens2941]

Hi Erik, i cant tell sorry.

[@TheDerekeder]

Thank you for your video. Next time please skip the music!

[@th8583]

Hi
Did You get the SAM out?

[@rickstevens2941]

I'm Lucky I don't have to do this all day,😉
But yes I always keep them Up 👍🏻😎👍🏻

[@deanraffie1745]

Hi Rick what part must replace. The problem is I connected n trailerlast Weekend n left side indicator was blinking fast in vechicle n outside bt then it stopt blinking outside stays on permanently bt blink fast inside What part must I replace Dean thanks South Africa