APC SRT 5KVA 02000 Inverter Hardware Ckt repaired
ฝัง
- เผยแพร่เมื่อ 28 ม.ค. 2024
- #apc #ups #upsrepairing
Apc Srt 5 Kva Ups Inverter Repair | Apc Ups Inverter Hardware Ckt | How to repair 02000 for Apc Ups
NOTE:
English subtitles are available for this video. The video language is urdu/hindi. If you don't understand this, then you can turn on the subtitles
Your searches
apc srt ups repair
how to repair ups
repair apc ups
online ups repair
ups repair
apc ups 02000 error
aps surt 5000xli
apc inverter hardware ckt
apc inverter repair
apc inverter fault 02000
apc inverter repairing
ups inverter repair
Power sys error 02000 contact customer support
APC UPS Inverter Repair and Troubleshooting
APC Inverter Repair Complete Guide
APC SRT 5KVA UPS Inverter drives repair
Fixing APC Inverter Faults
Troubleshoot and Repair Your APC Inverter error code 02000
APC Inverter Repair
APC UPS SRT Inverter error code 02000
inverter repairing
Inverter output fault
EEPROM Software Link 5KVA SRT and 6KVA SRT UPS
bit.ly/499WGZZ
#apc #apcups #ups #upsrepairing #inverter - วิทยาศาสตร์และเทคโนโลยี
This man is an amazing master in his job. With his help, through online consultation, we repaired two 5KV UPS controller board. . Only after describing the problem, he immediately showed us the damaged part... Now both of UPS working like a new. Lots of thanks and recommendations from me.
thank you very helpful video
Thanks
In your case was there any physically visible sign of fault with the driver sub-board? Was it a broken resistor or diode? If so I could probably check the driver boards more quickly, and not needing to make a signal frequency. Thank you for your in depth video. Subscribed and liked.
No
There is nothing physically damaged any diode or resistor. But I have done it for knowledge sharing. I think this is easy way to understand drive board.
@@AKElectroTech Hello! Did you simply swap the whole small board out?
You mean control card.
hello sir
is it normal to have flash arc from the back of the ups SRT10kva while doing ups test from the settings ?
No
I've tried this on two UPS now - SRT6K and SRT5K - with 02000 Event code 107 - in both cases all of the outputs read 17.xx volts when triggered with the 3VDC button cell. Do you think there is anywhere else worth checking?
One of them seems slow to raise to 17.xx VDC. I am thinking to swap that and see.
@@upstrader
Don't apply 3VDC directly on optocouplers input. Use 100 Ohm resistance in series with 3v cell.
This is what I am sharing is not SOP OF APC but my shortcut to reduce time. Otherwise you will use signal generator, power supply and oscilloscope to check optocouplers.
replace weak Optocoupler.
@@AKElectroTech OK I will repeat with the 100 Ohm resistor in series with the button battery.
I love your signal generation setup. I will make a short video and send to you via whatsapp
@@upstrader waiting at 00923215717132 wattsapp
Sir optocoplor 3121 out put se igbt ke gate tak ka complet circuit par tapsil se bat kare
Ok pl wait
Sir, what frequency must we use for the oscillator..? The level is clear.! Thank´s a lot
You can use 30k to 50k for checking purpose.
Thank´s a lot ! Greetings from Argentina..@@AKElectroTech
Wellcome
Thank you for this .. love from Nigeria... Please do more videos for us on apc .. my notifications bell is on
Ok brother
Thanks
Can you provide a drawing of where the 24v feed and triggering the gate driver?, or tell how trigger?
Brother
Pl see full video. At the end of the video you can see drawing of video and circuit to apply 24V and triggering with full detail on page.
Sir mere pass PCB 4G 3KVA PINTO TOWER UPS ON NAHI HO RAHA TOTALLY
Abbas Khan
As per your statement your UPS is dead and no response when switching on UPS.
There are various conditions.
Battery fuse F1 may be open.
Resistors R212, R245, R246 and R247 all having 4.7ohm resistance connected in parrallel may be open.
Q40 chopper switching transistor may be faulty.
R71, R194 and R195 having 1ohm value may be open.
IC12 UC3843 may be faulty.
Q45 used to switching ON UPS may be faulty.
Or
Check "ON button". With ribbon cable.
I hope you will find any solution regarding your fault for 4G 3KVA Pinto Tower UPS.
Sir i have sa ups apc srt10va that is showing 02000 with an error log Output relay weld code 164. ..what is the possibility fault and how to repair it?
Output relay weld event code is 165 for SRT10kva ups.
Now coming to Output relay weld.
Output relay may be fault or drive of relay is misbehaving.
Traic across relay may be short or drive of traic.
This fault is it on the inverter board or the pfc board ?
Inverter output relay located on inverter board
Sir apc srt5kxli error p13 event log inverter hardware ckt event code 107, how did repair
Pl see video carefully.
Same fault with "Inverter Hardware Ckt Event code 107"
First check IGBT and drives as shown in video. If problem remain then refresh EEPROm.
I hope you will find solution
I found that a line was broken due to corrosion, I have repaired it but the error is still the same
@@dimanaaja1910 pl wash your board to clear corrosion on board.
Assalamu'alaikum,Sir,Is there another solution, if we can't trigger pin number 2.4 on IC TC 4427? because I don't have a circuit board to trigger it,
Can we make a simple circuit to produce high frequencies?
WAS
Yes of course
But your oscillating level would be between 0v to 15v
Sir pl share ur No and ur workshop Location. I have APC ONLINE USP SURT 10000XLI. SHOWS BYPASS RELAY FAULT.
04235778236
00923215717132 wattsapp
Lahore
Thanks sir for reply. I saved ur No. Thanks a lot
Wellcome