There is just something about a random person on the internet fixing up old nostalgia things that makes you feel calm and collected after a tough week.
I remember doing this heat gun and thermal paste repair job on my PS3 by following a youtube guide back in around 2008. It was something that felt way beyond my capabilities but I had nothing to lose attempting it. I was so damn proud of myself when the PS3 fired as normal. I was always worried about having it running for too long after that, but it kept me going until I got the slim version. The slim eventually developed issues too, usually disc drive related. The PS3 gen had terrible reliability problems.
Using heat isn’t going to bring it back to life fully. It may be temporary but there’s no telling how long it could last. But most likely that issue is going to happen again. There is a diagnostic tool that you could purchase and it reads the syscon chip on the motherboard. Then it gives you error codes and that will tell you the issue. But considering this is a G01 and the temps get very high on this model I’d say that it’s probably the GPU solder bumps since the underfill was ment for lower temps but the PS3 worked the gpu like no tomorrow. The issue was eventually fixed in late 2008 with a higher temperature underfill. The underfill issue caused the solder bumps to crack under thermal stress so it might need a new gpu but it wouldn’t be worth it on this type of model Edit: also when you didn’t fix the thermal pad it made me die inside
YLOD is usually caused by the nictoken capacitors, usually heat brings them back to life but not for long, like you said, there are replacements that are better than the nictokens
@@Cristian121212100 not for these older models. Yes they are the same exact caps between all the phats but the model that are the K01 and below have a bad underfill on the GPU ment for lower temperatures. The early phats usually get very hot too. The RSX usually fails because the solder bumps between the die and the substrate crack due to thermal stress. So yes it could still be the Nec Tokins but there’s no real way of telling unless they do a diagnostic test
Bingo! I sent mine to some gorilla mod place in MN; bought me about 6 months of use then that was it; bought a slim and was happy with it until the pos plastic casing would have some random rattling noise depending upon fan speeds… so after that I said F this, n built my first gaming pc n never looked back!
There’s also thermal paste under the IHS plates (the big metal plates that the thermal paste was on) it’s difficult to remove but replacing that paste would also exponentially help in keeping it even cooler too
I just got a launch PS3 for $30. Aside from the disc drive needing replacing, it works perfectly fine, which for a console from November of 2006 is incredible.
Great video, very nice to watch, however as I'm sure many have told you in comments already - this isn't going to solve the issue. The CPU and GPU are not at fault here, the issue has been mistaken to be the solder balls cracking or overheating for many years, but only a few years ago we discovered the real cause of the issue. The actual culprit was the low profile NEC Tokien capacitors, which are the pairs of black rectangles you see a pair of next to the CPU and GPU on either side. The problem is they slowly stop working over time, causing the YLOD. The reason we never discovered these were causing the fault was because applying heat to the CPU / GPU as you do in this video also heats up the NEC caps, which temporarily makes them work again from the heat - this caused people to misdiagnose the CPU/GPU to be at fault. The real fix is actually relatively easy. :) You heat up or scrape away at one or two of the NEC capacitors to remove them. Personally I recommend using a small knife and a soldering iron to destroy and melt away the capacitors, instead of using a heat gun to desolder them, since there is many tiny capacitors and components located nearby them. Once removed, scratxh away at the board below to reveal the copper, since there is a large grounding plane around them, and then replacing each NEC cap with 4 tantalum capacitors at 470uf (iirc), soldered to the positive the capacitor used, and the revealed grounding plane. After replacing one or all of the NEC caps with 4 tantalum caps, the PS3 will reliably work again :) The best part is that this is a lasting fix, it won't stop working after 10 years or anything
No it depends per every console we can diagnose it by how long does it take to get the light. Heres a vid explaining it th-cam.com/video/UXrPN2mEriM/w-d-xo.html
These systems are so old when you take them apart the thermal paste is always dried up causing cpu gpu to overheat causing solder balls to crack underneath causing ylod sometimes I could be the nec tokin if you reflow the cpu gpu remove the heat spreaders put mx4 your console will be so quiet you will barely hear it
I remember back in 2009 having the YLOD and then Sony not apologising for their poor design for this console overheating. Bringing back nightmares but also nostalgia fixing it up with my dad 😆 needless to say i flogged it on ebay as spare parts and used the money to buy a slim line which i still have to this day! 🥳
This video recalls my memory of my old fat white ps3. It died of the same reason - triple "dood". I still keep it and I really hope I can send it to you for repair. Its just like it happened yesterday. 😢😢😢
First time I’m catching one of these. I’m new here from the candy machine and went down the retrobrighting hole with your videos (as well as some other restorations). Just wanted to say thanks so much for making these high quality, relaxing and informative videos :)
I'm surprised this system is thought of like that an old console to me is a colecovision, Magnavox Odyssey, Atari 2600, 1970s Pong 5 System, Intellivision, RCA Studio I and II, etc.
Just a little word of advice, if you're ever to clean one of these again, I would suggest using a microfiber towel instead of a paintbrush on the top cover. The paintbrush has a high chance of creating normal scratches and micro scratches on the glossy plastic.
Is it silly for me to say that those scratches can be restored? Like wasn’t there some spray and stuff you could buy back then to restore cd scratches?
Even if you do try to "fix" the scratches after they are there, they will never truly go away, you will just repolish the already scratched finished which most times will actually make it more visible. Your not wrong though, sometimes that can work but its not guaranteed.
La de 80GB es semi retrocompatible (compatibilidad limitada con juegos de PS2). El 75% de los juegos funcionan bien. Los demás sufren caídas de framerate, alentamientos, errores gráficos o cuelgues aleatorios. Las únicas 100% retrocompatibles son las de 20 y 60gb hechos en USA y Japón por tener el procesador del PS2 integrado (Emotion Engine)
Great job, I enjoyed it very much. I think I could take this apart but I could NEVER reassemble it. You may want to consider investing in a small air compressor and a small vacuum to blow out and suck up dust and dirt. It would make things so much easier for you. Thanks for the video!
This reminds me of my childhood PS3. After years of love, it suffered the same fate (although instead of refusing to come on, it would just die randomly when in use. You can imagine the frustration). We knew how to fix it but didn't have the means to (and my dad doesn't feel comfortable with soldering anymore since his eyesight is bad at times), so whenever it got so bad we couldn't stand it, my dad and I would take it apart and put the motherboard in the oven. Not the most glamorous fix, but it worked for a while and we got some extra time out of it. We still have it somewhere and I've always hoped I'd be able to have the means to fix it c:
This technique is common, but YLOD recurs quickly. I also got several PS3s from discarded items at a hotel run by an acquaintance, so I repaired them many times, but in the end YLOD recurred. After all, once YLOD occurs, the PS3's CPU and GPU contact surface tear is not easily cured.
Ylod was diagnosed wrong for all these years, maybe because of the 360 RROD (and that was diagnosed wrong too, it was not for a break connection between motherboard and GPU, but a break inside the GPU itself). The problem it’s not the gpu or cpu chips but probably one of the NEC capacitors gone bad. With reflow you just force this component to work, but the issue will appear again. And when it will happen, check for a short in these capacitors.
It still under testing, I bought 470uf / 6.3V Tantalum Capacitors, and I will replace the NEC capacitors if the issue (YLOD )will appear again again, Thanks for the tip!❤️
Big mistake ... There is also a paste under the RSX plate that needs to be replaced .... That's why the ps3 gets hot ..... You have to cut the plate and replace the paste there, it is the main cause of overheating
That was my dream as a 13 years old young boy! But my family could't give me one at the time of financial crysis, thought. And when i was having my money, it long gone the era of it. Nice to see a restouration like this. I'll buy one for honor one day if i found one in good condition.
I heared there was drama with a refurb seller in canada not even opening up their devices. so I wanted to know what comes with refurbishing. so many great channels that do amazing work
Yo tenía la misma, llegué a desmontarla lo menos 15 veces, haciendo lo que tu haces, pero me duraba 20 días a lo sumo. Al final la vendí y compre la slim.
Si o si hay que va cambiar el estaño debajo de los microprosedores, utilizar estaño con plomo que es más resistente a los cambios constantes de temperatura
I did this twice to my 60gb PS3 years ago (reflowed). It's a temp fix, it won't last. The NEC Tokin capacitors are the main culprits. They need to be replaced for better quality, tantalum capacitors. Paste under the IHS also needs replaced. Both not an easy task. That's why my ps3 currently sits in a cupboard lol.
This. Reflowing should not be recommended as the first step anymore this is been proven a few years back. Reflowing doesn't "fix" them the majority of the time. It just temporarily rejuvenates the NEC capacitors. The real permanent fix is to just replace the capacitors and not to reflow the chips unless absolutely necessary.
@@jeffescortlx ya try telling that to the people who think it's a cracked solder joint that needs reflowed 😂 they're gonna die on that hill. they think that since reflowing it "works" that it must be one of the bga joints and couldn't possibly be anything else. I've got an A01 delidded with LM applied to the dies and am waiting til I need to replace a cap to replace a cap.
@@cheeryos116 your not kidding. In my own video I have people commenting that it's only failed caps like 2% of the time and that it's a myth that the NEC's fail commonly. In a video where I literally only replace the Caps without a reflow and it fixed YLOD.
I have read that the heat is just a temporal fix for a condemned PS3... The real problem is inside the dye of the processor and to fix it you need a lot of heat, which destroy the components and can be done only during the manufacturing process.
Muito Bom, porém faltou um detalhe até aonde prestei bastante atenção, só faltou ele colocar a bateria da bios no lugar, mas fora isso deu certo! Parabéns pelo belo trabalho. ^^
Won't last long doing this. Should have Delidded the RSX cover and the other cover, re-apply thermal paste and boom you just gave this ps3 5+ years of life
*Awesome Video Dear Brother Restoration EG... Thanks For Share this Great Job in Repairing PlayStation 3 Fat... Long Life for PS3!!! Good Mini Gameplay of Assassin's Creed...* 😎😁😀😆📱💁🏻♂️📺🎥🎬🎮🕹👨🔧🛠🧤💦📼💿✌👍
Reheating the solder on the CPU and GPU isn't going to help, the real issue is the NEC capacitors (the flat black ones). They become slightly re-conditioned after the heat-gun treatment but the problem is going to come back. You need to replace the NEC capacitors with identical resistance and capacitance.
Didn’t someone discover that the capacitors was just one of the issues? I saw someone on TH-cam reball something and I forget what it was- I don’t know enough about motherboards to remember lol. I’ve wanted to do this type of repair to my YLOD but I keep it for a rainy day when I want to try and fix it
@@mikejonez724 Care to elaborate? I’m not gonna deny there could be other reasons for YLOD like bad solder points (some very early models had bad quality solder), but given the correlated result by replacing the capacitors it’s hard to argue against the methodology so I’m eager to hear the claim.
I’m very glad my PS3 fat is still working perfectly. I have an original and while I don’t use it often, it comforts me in some weird way to know it is okay.
My PS3 60 Gb Fully Backwards Model Still Working Perfectly! My Most Favourite Console PS3 60 Gb Fully Backwards Compatible System In The World For The Lifetime.
9 months late but I think from that this console possibly wasn't used much even with all the scratches and the ylod or it has been taken apart before idk couldn't tell you
I Have PS3 (60 GB) & My Last Game Which I Beat Is Max Payne 3 On That System! What A Masterpiece Console Of Lifetime PS3 (60 GB) Fully Backwards Compatible System.
I was never open a PS3 fat because I never owned one but I've heard there's a lot of issues with the mostly because the motherboard I have a PS3 Slim 160gb I can say for sure that I open that one completely and clean it you have to be very careful when opening it and taking it apart one little mistake can cost you your PS3
Bonito tutorial para que funcione 10 minutos y salte de nuevo la luz amarilla. La unica solución es reballing, te cobran lo que cuesta la Ps3, es resoldar todas las soldaduras del chip y aun asi con el tiempo vuelve a morir por mal diseño de hardware como todas las consolas de Sony.
10 minutos no a mi me dura como dos meses más y vuelve la luz amarilla dewpues tengo que volver a calentar otra vez pero yo meto toda la placa al horno a 250 grados por 4 minutos jajajajajaja ya lo he hecho como dos veces y si funciona por un buen rato de todos modos si no lo haces ya quedaría inservible la consola
Ya no se empeñan en hacer las cosas bien y todavía le ponen que es una restauración por que lavo las piezas de plástico, es una porquería su trabajo, todos las cosas que según el restaura las hace a lo tonto sin saber
Mi consola favorita,tiene un diseño increíble, la mía igual murió por luz amarilla,la mandé con un "técnico" y aparte que no la reparo me rompió el seguro de la tapa de Playstation y se quedó con mi cable de alimentacion.
@@starkiller7057if you’re console has high temperatures or the fan is loud than you have to delid rsx and cell .if you want to reflow a ylod console it is best to heat the chips and then delid it when you delid the chips then you can do the proper rsx reflow (do not reflow the cpu the cpu is good) and then repaste it
É uma boa solução temporária mas em breve pode voltar a dar defeito , A Sony deveria ter colocado a fonte de forma externa e assim não aqueceria tanto , Mesmo com um cooler muito grande ainda deu muito defeito .
True story- my house got broken into a couple of times in a short period of time. I decided that when I went out of town, I would put the ps3 in the oven. Nobody would ever look in there, I thought. Completely forgot about it. Decided to make some brownies and set the oven to preheat. Smelled something burning which of course was plastic from the ps3. I shit you not it was partially melted and still fired up. The fan was exposed somewhat but it still turned on and did it’s job. I took a picture of it and sent it to Sony. Lmao. Never replied back
Working in a bottle depot, back in the day, I identify with each instant I see Restoration EG's fingers protruding through his gloves. I know that effort.
I'm convinced that my first PS3 console eventually gave out because of lack of thermal paste on the CPU. But I didn't know that at the time. Plus I didn't know how to open it up, much less had the resources and/or capabilities to fix it myself so I just ended up calling their consumer service line and traded in that PS3 for another one. It was the super slim model
Always remember having the yellow light of death during a COD game, then we had to open the PS3 up and blow a hair dryer on the main two chips till we got life again, this was a temp thing so I could backup my internal HD to an external HD. Never had any problems with the slim PS3, but my older PS3 with the yellow light was an original one with the backwards compatability.
If you don’t have a pc ps3 is the best way to go to play older titles. I bought one a couple years ago and love it. This looks like an older model it might be backwards compatible. Those are hat pro usually want when getting one
Another good fix. Watched it very close because few days ago my PS3 begun do the ylod After short time Turning on. Your model Is the 40Gb, mine Is 80Gb. Outside all fat models seem the same (except for 60Gb with 4 USB ports) but inside Is another world. Different position of WiFi, the socket of HD and the plate Who cover CPU and GPU with 2 lines. And the silver Power supply different from the black One in the 80Gb model; not to mention the backflip fan in the bottom of console. PS: I was playing that AC chapter too before the the appear of ylod.
There is just something about a random person on the internet fixing up old nostalgia things that makes you feel calm and collected after a tough week.
Same, also the fact that i could have never bought these items when i was a kid (and now they are old and obsolate) gives it a different vibe
Dude your name is literally max Payne get lost scrub
@@nekosanestacado8661 who the fuck is nekosan estacado
Many many thanks
@@nekosanestacado8661 look at your name and think twice
I remember doing this heat gun and thermal paste repair job on my PS3 by following a youtube guide back in around 2008. It was something that felt way beyond my capabilities but I had nothing to lose attempting it. I was so damn proud of myself when the PS3 fired as normal. I was always worried about having it running for too long after that, but it kept me going until I got the slim version. The slim eventually developed issues too, usually disc drive related. The PS3 gen had terrible reliability problems.
My ultra slim has been alright
@@windowstips1430the ultra slim is the best version by far, cause the simplicity of the hardware.
@@fascistalien ya
I guess I was lucky since my PS3 never had issues. Even after a decade, it never acted up.
yea im trying to fix mine cuz of the yellow ring of death
Restoration eg your like one of the few actual legitimate restoration channels nice job
I fixed my PS3 because of your instructions. Thank you Resto! Much love from Indiana.
How long did it go!?
Using heat isn’t going to bring it back to life fully. It may be temporary but there’s no telling how long it could last. But most likely that issue is going to happen again. There is a diagnostic tool that you could purchase and it reads the syscon chip on the motherboard. Then it gives you error codes and that will tell you the issue. But considering this is a G01 and the temps get very high on this model I’d say that it’s probably the GPU solder bumps since the underfill was ment for lower temps but the PS3 worked the gpu like no tomorrow. The issue was eventually fixed in late 2008 with a higher temperature underfill. The underfill issue caused the solder bumps to crack under thermal stress so it might need a new gpu but it wouldn’t be worth it on this type of model
Edit: also when you didn’t fix the thermal pad it made me die inside
I've also heard that the NEC TOKIN chips near CPU and GPU might be responsible for the system's malfunction.
The fact he didn't removed the HDD before anything else, that right there I lost any hope
YLOD is usually caused by the nictoken capacitors, usually heat brings them back to life but not for long, like you said, there are replacements that are better than the nictokens
@@Cristian121212100 not for these older models. Yes they are the same exact caps between all the phats but the model that are the K01 and below have a bad underfill on the GPU ment for lower temperatures. The early phats usually get very hot too. The RSX usually fails because the solder bumps between the die and the substrate crack due to thermal stress. So yes it could still be the Nec Tokins but there’s no real way of telling unless they do a diagnostic test
Bingo! I sent mine to some gorilla mod place in MN; bought me about 6 months of use then that was it; bought a slim and was happy with it until the pos plastic casing would have some random rattling noise depending upon fan speeds… so after that I said F this, n built my first gaming pc n never looked back!
There’s also thermal paste under the IHS plates (the big metal plates that the thermal paste was on) it’s difficult to remove but replacing that paste would also exponentially help in keeping it even cooler too
I remember trying this on my PS3 and it made the temps higher because I think I bent the IHS lmao
I really agree with you, thanks for watching❤️
thanks for watching❤️
It does more harm than good, not worth the effort. See a lot of people do it to these but it’s really not necessary.
@@TKdoh on some older models it is. The gpu is actually pretty easy to do. Just take a flat head and pry up after you use a heat gun on it
I just got a launch PS3 for $30. Aside from the disc drive needing replacing, it works perfectly fine, which for a console from November of 2006 is incredible.
Not for a long time, gpu will fail eventually.
@@---777--- Not if you replace the thermal paste and stuff. Should be fine
Great video, very nice to watch, however as I'm sure many have told you in comments already - this isn't going to solve the issue.
The CPU and GPU are not at fault here, the issue has been mistaken to be the solder balls cracking or overheating for many years, but only a few years ago we discovered the real cause of the issue. The actual culprit was the low profile NEC Tokien capacitors, which are the pairs of black rectangles you see a pair of next to the CPU and GPU on either side. The problem is they slowly stop working over time, causing the YLOD. The reason we never discovered these were causing the fault was because applying heat to the CPU / GPU as you do in this video also heats up the NEC caps, which temporarily makes them work again from the heat - this caused people to misdiagnose the CPU/GPU to be at fault.
The real fix is actually relatively easy. :)
You heat up or scrape away at one or two of the NEC capacitors to remove them. Personally I recommend using a small knife and a soldering iron to destroy and melt away the capacitors, instead of using a heat gun to desolder them, since there is many tiny capacitors and components located nearby them.
Once removed, scratxh away at the board below to reveal the copper, since there is a large grounding plane around them, and then replacing each NEC cap with 4 tantalum capacitors at 470uf (iirc), soldered to the positive the capacitor used, and the revealed grounding plane.
After replacing one or all of the NEC caps with 4 tantalum caps, the PS3 will reliably work again :)
The best part is that this is a lasting fix, it won't stop working after 10 years or anything
T aurait une photo à nous montrer du remplacement des condensateur que tu parle. Sa m intéressé de réparer la mienne de façon sur.
No it depends per every console we can diagnose it by how long does it take to get the light. Heres a vid explaining it th-cam.com/video/UXrPN2mEriM/w-d-xo.html
These systems are so old when you take them apart the thermal paste is always dried up causing cpu gpu to overheat causing solder balls to crack underneath causing ylod sometimes I could be the nec tokin if you reflow the cpu gpu remove the heat spreaders put mx4 your console will be so quiet you will barely hear it
The Thermal Paste is the fault on some consoles like Xbox 360
@@BeinZilex replaced maybe but a reflow does the trick
I remember back in 2009 having the YLOD and then Sony not apologising for their poor design for this console overheating. Bringing back nightmares but also nostalgia fixing it up with my dad 😆 needless to say i flogged it on ebay as spare parts and used the money to buy a slim line which i still have to this day! 🥳
the ylod is caused by several other things, not just overheating
yo m*mma gets animated at night
This video recalls my memory of my old fat white ps3. It died of the same reason - triple "dood". I still keep it and I really hope I can send it to you for repair. Its just like it happened yesterday. 😢😢😢
First time I’m catching one of these. I’m new here from the candy machine and went down the retrobrighting hole with your videos (as well as some other restorations). Just wanted to say thanks so much for making these high quality, relaxing and informative videos :)
Very satisfying watch. Always great when you see these old classic consoles brought back to life. Well done sir.
I'm surprised this system is thought of like that an old console to me is a colecovision, Magnavox Odyssey, Atari 2600, 1970s Pong 5 System, Intellivision, RCA Studio I and II, etc.
I wouldn't say PS3 is a classic quite yet, but it's definitely getting there.
Just a little word of advice, if you're ever to clean one of these again, I would suggest using a microfiber towel instead of a paintbrush on the top cover. The paintbrush has a high chance of creating normal scratches and micro scratches on the glossy plastic.
Agreed, that's exactly what I observed he makes mistake on cleaning it this way especially the plastic
Is it silly for me to say that those scratches can be restored? Like wasn’t there some spray and stuff you could buy back then to restore cd scratches?
Even if you do try to "fix" the scratches after they are there, they will never truly go away, you will just repolish the already scratched finished which most times will actually make it more visible. Your not wrong though, sometimes that can work but its not guaranteed.
This brush seems to be super soft
Wow, I can't believe I watched the whole thing and was extremely satisfied
Todavía uso mi PS3 fat 80 gigas retrocompatible y ya en marzo cumple sus 15 años. Maravillosa consola! Greetings from Mexico City!
¡Me alegra que lo hayas disfrutado! ❤️
Nunca se te dañó?
la PS3 solo es retrocompatible la de 60gigas la de 40 80 y 160 gigas no eran retrocompatible
lavar la tapa no soluciona la luz amarilla para reparar la
La de 80GB es semi retrocompatible (compatibilidad limitada con juegos de PS2). El 75% de los juegos funcionan bien. Los demás sufren caídas de framerate, alentamientos, errores gráficos o cuelgues aleatorios. Las únicas 100% retrocompatibles son las de 20 y 60gb hechos en USA y Japón por tener el procesador del PS2 integrado (Emotion Engine)
This isn't just a random guy fixing nostalgic stuff .. It's THE random guy fixing nostalgic stuff and giving everything a soapy bath..
Great job, I enjoyed it very much. I think I could take this apart but I could NEVER reassemble it. You may want to consider investing in a small air compressor and a small vacuum to blow out and suck up dust and dirt. It would make things so much easier for you. Thanks for the video!
This reminds me of my childhood PS3. After years of love, it suffered the same fate (although instead of refusing to come on, it would just die randomly when in use. You can imagine the frustration). We knew how to fix it but didn't have the means to (and my dad doesn't feel comfortable with soldering anymore since his eyesight is bad at times), so whenever it got so bad we couldn't stand it, my dad and I would take it apart and put the motherboard in the oven. Not the most glamorous fix, but it worked for a while and we got some extra time out of it. We still have it somewhere and I've always hoped I'd be able to have the means to fix it c:
This technique is common, but YLOD recurs quickly.
I also got several PS3s from discarded items at a hotel run by an acquaintance, so I repaired them many times, but in the end YLOD recurred.
After all, once YLOD occurs, the PS3's CPU and GPU contact surface tear is not easily cured.
This has motivated me to pull out my old first gen PS3 Fat to get her back working
Ylod was diagnosed wrong for all these years, maybe because of the 360 RROD (and that was diagnosed wrong too, it was not for a break connection between motherboard and GPU, but a break inside the GPU itself). The problem it’s not the gpu or cpu chips but probably one of the NEC capacitors gone bad. With reflow you just force this component to work, but the issue will appear again. And when it will happen, check for a short in these capacitors.
It still under testing, I bought 470uf / 6.3V Tantalum Capacitors, and I will replace the NEC capacitors if the issue (YLOD )will appear again again, Thanks for the tip!❤️
@@resEG PS3 uses 1200uf / 2.5v capacitors, you could put 4 400uf / 2.5v parallel capacitors
this was debunked tho
@@resEG can you do a video for the replacing I would be happy thanks
I've had my PS3 stopped for years. I was told that the NEC Token capacitors also caused problems. I will try to fix it. Thanks for the tutorial.
thanks for watching❤️
Big mistake ... There is also a paste under the RSX plate that needs to be replaced .... That's why the ps3 gets hot ..... You have to cut the plate and replace the paste there, it is the main cause of overheating
yes
That was my dream as a 13 years old young boy! But my family could't give me one at the time of financial crysis, thought. And when i was having my money, it long gone the era of it. Nice to see a restouration like this. I'll buy one for honor one day if i found one in good condition.
Really like the chanal. Has made me want to restore my old consoles for myself.
Glad you enjoyed it! ❤️
I heared there was drama with a refurb seller in canada not even opening up their devices. so I wanted to know what comes with refurbishing. so many great channels that do amazing work
Awesome job with the fix. Excellent video.😎
Vídeo muito satisfatório, é muito legal ver o aparelho funcionando normalmente
Xander?
Yo tenía la misma, llegué a desmontarla lo menos 15 veces, haciendo lo que tu haces, pero me duraba 20 días a lo sumo. Al final la vendí y compre la slim.
gracias por ver
sad
Lo malo del reflow es que puede durar 2 semanas o 2 años.
Es una lotería, buen video sobre el desmontaje de nuestras gorditas.
Si o si hay que va cambiar el estaño debajo de los microprosedores, utilizar estaño con plomo que es más resistente a los cambios constantes de temperatura
Another top-notch repair of a video game console. Most excellent. 👍
I did this twice to my 60gb PS3 years ago (reflowed). It's a temp fix, it won't last. The NEC Tokin capacitors are the main culprits. They need to be replaced for better quality, tantalum capacitors. Paste under the IHS also needs replaced. Both not an easy task. That's why my ps3 currently sits in a cupboard lol.
¡Me alegra que lo hayas disfrutado! ❤️
This. Reflowing should not be recommended as the first step anymore this is been proven a few years back. Reflowing doesn't "fix" them the majority of the time. It just temporarily rejuvenates the NEC capacitors. The real permanent fix is to just replace the capacitors and not to reflow the chips unless absolutely necessary.
@@jeffescortlx ya try telling that to the people who think it's a cracked solder joint that needs reflowed 😂 they're gonna die on that hill. they think that since reflowing it "works" that it must be one of the bga joints and couldn't possibly be anything else. I've got an A01 delidded with LM applied to the dies and am waiting til I need to replace a cap to replace a cap.
@@cheeryos116 your not kidding. In my own video I have people commenting that it's only failed caps like 2% of the time and that it's a myth that the NEC's fail commonly. In a video where I literally only replace the Caps without a reflow and it fixed YLOD.
@@jeffescortlx Yep, it's 100% the NEC's. Toshiba laptops failed because of them as well.
I have read that the heat is just a temporal fix for a condemned PS3... The real problem is inside the dye of the processor and to fix it you need a lot of heat, which destroy the components and can be done only during the manufacturing process.
Muito Bom, porém faltou um detalhe até aonde prestei bastante atenção, só faltou ele colocar a bateria da bios no lugar, mas fora isso deu certo! Parabéns pelo belo trabalho. ^^
Percebi isto tbem.
Won't last long doing this. Should have Delidded the RSX cover and the other cover, re-apply thermal paste and boom you just gave this ps3 5+ years of life
Your videos are so relaxing and satisfying u.u
*Awesome Video Dear Brother Restoration EG... Thanks For Share this Great Job in Repairing PlayStation 3 Fat... Long Life for PS3!!! Good Mini Gameplay of Assassin's Creed...* 😎😁😀😆📱💁🏻♂️📺🎥🎬🎮🕹👨🔧🛠🧤💦📼💿✌👍
Many many thanks❤️❤️
💕💕fantastic relaxation❤ ASMR
Glad you liked it!!
It was very interesting to watch you! You are like a teacher! thanks!
Glad you enjoyed it! thanks for watching❤️
you're the boss! Amazing video as always man! 😎😎😎
You're the best!, Glad you enjoyed it! ❤️
You Repaired a lot of PlayStations!
Awesome Work!
Yes, thanks, Glad you enjoyed it! ❤️
this is not repair
Reheating the solder on the CPU and GPU isn't going to help, the real issue is the NEC capacitors (the flat black ones). They become slightly re-conditioned after the heat-gun treatment but the problem is going to come back. You need to replace the NEC capacitors with identical resistance and capacitance.
Didn’t someone discover that the capacitors was just one of the issues? I saw someone on TH-cam reball something and I forget what it was- I don’t know enough about motherboards to remember lol. I’ve wanted to do this type of repair to my YLOD but I keep it for a rainy day when I want to try and fix it
3 or 4 470uF tantalum capacitors to be exact for each NEC.
It was just recently determined that those capacitors were not the cause of the YLOD they're totally fine to keep.
@@mikejonez724 Care to elaborate? I’m not gonna deny there could be other reasons for YLOD like bad solder points (some very early models had bad quality solder), but given the correlated result by replacing the capacitors it’s hard to argue against the methodology so I’m eager to hear the claim.
@@mikejonez724 10 to 20% could be NEC TOKINs. The majority is usually the RSX.
I’m very glad my PS3 fat is still working perfectly. I have an original and while I don’t use it often, it comforts me in some weird way to know it is okay.
My PS3 60 Gb Fully Backwards Model Still Working Perfectly! My Most Favourite Console PS3 60 Gb Fully Backwards Compatible System In The World For The Lifetime.
Amo esse console parabéns pelo vídeo e sucesso ao seu canal❤
Theres no world where this works as ASMR because YLOD produces internal screaming
Valeu pela aula... Parabéns pelo bom trabalho...
Muitíssimo obrigado
@@resEG eu que agradeço. Bom dia...
Obrigada pelo video, e pela descrição em português BR! Show de bola o canal!
Now I can make my ps3 work again in the world of the living
Thank you
Que video lindo e satisfatório amigo, parabéns! Farei o mesmo no meu ps3 aqui em breve ! Obrigado
Thank you my ps3
Hvala tebi sto sam pomocu tvajih redosleda popravio svoj plejstejsn 3.
Bros ps3 is not gonna last long
Excelente vídeo. Saludos y bendiciones desde Colombia 👌🏻👍🏻
¡Me alegra que lo hayas disfrutado! ❤️
Great job as always friend, that model apart from being beautiful was backward compatible, it hurts about overheating.
Yes it was, Glad you enjoyed it! ❤️
That’s not PS2 backwards compatible.
It's shocking that the fan didn't had much dust on it despite being such a old console
9 months late but I think from that this console possibly wasn't used much even with all the scratches and the ylod or it has been taken apart before idk couldn't tell you
It’s crazy how old the PS3 is now. I still remember when it was the latest game console.
Ficou top.
Já aproveito e jogou logo um jogo pesado de PS3. Pra testa logo a CPU. Top
mas assassins creed rogue é levinho
@@gemsm7377 e deve ser mais os gráficos tava top
@@gemsm7377 mas é um jogo que 2014 que no ps3 é melhor que no xbox 360 e no pc o jogo fica travando
У моего тёзки была такая же PlayStation 3. Вот точь в точь такая же.
Только Slim.
Exelente trabajo amigo 👏¿ tienes vídeos de reparaciones de los joysticks de controles?
Muitíssimo obrigado ❤️
素晴らしいです。
所持しているPS3(60GB)は2006年に購入して今でも使えていますが、壊れてしまった時はダメ元で参考にさせて頂いて試行錯誤してみたいです。
発売当時は大騒ぎでしたね。
I Have PS3 (60 GB) & My Last Game Which I Beat Is Max Payne 3 On That System! What A Masterpiece Console Of Lifetime PS3 (60 GB) Fully Backwards Compatible System.
I was never open a PS3 fat because I never owned one but I've heard there's a lot of issues with the mostly because the motherboard I have a PS3 Slim 160gb I can say for sure that I open that one completely and clean it you have to be very careful when opening it and taking it apart one little mistake can cost you your PS3
I really agree with you, thanks for watching❤️
MY FAVORITE CONSOLE 🤩🤩🤩 i'm so Happy that i still have ONE 😁
thanks! Glad you enjoyed it! ❤️
who asked tho
Ótimo vídeo ❤❤
Que bom que você gostou! ❤️
That is such an awesome little screwdriver set. I have one too.
Parabéns
Vc conseguiu colocar esse PS3 de volta a vida
Muito obrigado ❤️
BRAVO une PLAYSTATION 3 fat sauvé de la déchèterie 👍👍
جميل ورائع مبدع شكراً لك 👍🏻♥️
شكرا للمشاهدة والرد الجميل
هل صادق
انا لسه ما جربة الطريقه لاكن بس واثق فيك👊👊استمر يا وحش⬆⬆
Bonito tutorial para que funcione 10 minutos y salte de nuevo la luz amarilla. La unica solución es reballing, te cobran lo que cuesta la Ps3, es resoldar todas las soldaduras del chip y aun asi con el tiempo vuelve a morir por mal diseño de hardware como todas las consolas de Sony.
10 minutos no a mi me dura como dos meses más y vuelve la luz amarilla dewpues tengo que volver a calentar otra vez pero yo meto toda la placa al horno a 250 grados por 4 minutos jajajajajaja ya lo he hecho como dos veces y si funciona por un buen rato de todos modos si no lo haces ya quedaría inservible la consola
Ya no se empeñan en hacer las cosas bien y todavía le ponen que es una restauración por que lavo las piezas de plástico, es una porquería su trabajo, todos las cosas que según el restaura las hace a lo tonto sin saber
Awesome job, friend! Congrats!
Все четко красиво.автор молодец.но вряд ли проработает долго
реставрация на один день)
I go way back with assassins creed 3 Fire video
Mi consola favorita,tiene un diseño increíble, la mía igual murió por luz amarilla,la mandé con un "técnico" y aparte que no la reparo me rompió el seguro de la tapa de Playstation y se quedó con mi cable de alimentacion.
Should’ve just bought another one there cheap these days
Original Ps3 looks better than the ps5
Nice video, bro 👏👏👏👏
Glad you liked it
Is it a permanent solution ?
If the nec tokins are problem then no but if the gpu was problem 70% of the time it will work if you do it with flux and a lot of heat
@@Aleksa.09no need for de lidding?
@@starkiller7057if you’re console has high temperatures or the fan is loud than you have to delid rsx and cell .if you want to reflow a ylod console it is best to heat the chips and then delid it when you delid the chips then you can do the proper rsx reflow (do not reflow the cpu the cpu is good) and then repaste it
You have to use heatgun at the front and the back of the RSX
I have the same console, same issue. I saved this video for my future fix
Mano poderia dizer que curso você fez para aprender a desmontar e montar tudo isso véi
Love the videos. Can you explain what it is you wiped along the edges of the processors @9:59 please.
soldering flux, Glad you enjoyed it! ❤️
@@resEG ok thanks.
É uma boa solução temporária mas em breve pode voltar a dar defeito ,
A Sony deveria ter colocado a fonte de forma externa e assim não aqueceria tanto ,
Mesmo com um cooler muito grande ainda deu muito defeito .
Esse defeito é solda fria?
Yep!My favorite repair video:D
Glad to hear it!❤️ thanks!
Esse console é lindo demais 😍
True story- my house got broken into a couple of times in a short period of time. I decided that when I went out of town, I would put the ps3 in the oven. Nobody would ever look in there, I thought. Completely forgot about it. Decided to make some brownies and set the oven to preheat. Smelled something burning which of course was plastic from the ps3. I shit you not it was partially melted and still fired up. The fan was exposed somewhat but it still turned on and did it’s job. I took a picture of it and sent it to Sony. Lmao. Never replied back
Muito bom parabéns
Muitíssimo obrigado
I swear If my console ever get red ring or something is wrong I’ll hit up my plug this man here who can fix anything 💯
Or simply buy another as that’s a cheaper option
Amei ❤️
Muitíssimo ❤️
@@resEG mas sabe que esse reflow não é garantido ? o ideal seria substituir as esferas de solda
Esse canal é BR? Kk
@@makinamara321654 and you will
@@makinamara321654 não
one of the best generation , iknow that time was hard to sony but in the end they succeeded 🙃
Прогрев чипа да временную работу, пустая трата времени, хотя людям контент такой заходит, но по факту эта работа псу под хвост!
That is a fantastic transformation!!
Many many thanks
Assassin's Creed Fan here. I played it all.
Great Video but you forgot the thermal paste under the IHS plates. Also, use a HDMI cable bro :D that gameplay was like 480p
Thanks for the tip!
There is nothing this man cannot fix😎
Thanks I really appreciate you! 🙏
Cleanest ps3 fan ever
Working in a bottle depot, back in the day, I identify with each instant I see Restoration EG's fingers protruding through his gloves. I know that effort.
Glad to hear that! thanks for watching❤️
Great video! What is the screwdriver brand?
I'm convinced that my first PS3 console eventually gave out because of lack of thermal paste on the CPU. But I didn't know that at the time. Plus I didn't know how to open it up, much less had the resources and/or capabilities to fix it myself so I just ended up calling their consumer service line and traded in that PS3 for another one. It was the super slim model
Always remember having the yellow light of death during a COD game, then we had to open the PS3 up and blow a hair dryer on the main two chips till we got life again, this was a temp thing so I could backup my internal HD to an external HD. Never had any problems with the slim PS3, but my older PS3 with the yellow light was an original one with the backwards compatability.
Many many thanks
If you don’t have a pc ps3 is the best way to go to play older titles. I bought one a couple years ago and love it. This looks like an older model it might be backwards compatible. Those are hat pro usually want when getting one
thanks for watching
12:45 : I thought you've put the WHOLE console in the water, I was about to completely freak out lmao
Another good fix. Watched it very close because few days ago my PS3 begun do the ylod After short time Turning on. Your model Is the 40Gb, mine Is 80Gb. Outside all fat models seem the same (except for 60Gb with 4 USB ports) but inside Is another world. Different position of WiFi, the socket of HD and the plate Who cover CPU and GPU with 2 lines. And the silver Power supply different from the black One in the 80Gb model; not to mention the backflip fan in the bottom of console.
PS: I was playing that AC chapter too before the the appear of ylod.
thanks for watching 💕
Awesome video!!! Do you have a link where I could get that screw kit from??
Actually he does in the description
@@TheSubZero187 I’m not seeing one in the description
Great job on the fix.
Beautiful video and beautiful console, i suggest you to install an SSD into the PS3, it becomes much faster, silent and reliable
✌
The joy of fixing things but in asmr