Dyson Blue Light Blinking / Flashing [How to Fix this?!]

WATCH PART 2 HERE: • FIXING DYSON BLUE LIGH... (I made a new video about fixing a Dyson with a blue light, because this video previous doesn't cover all the different Dyson models!).
If the blue light blinks while vacuuming, there may be a problem with your Dyson vacuum cleaner. I’ve researched all the possible reasons why the blue Dyson light is blinking and how you can quickly solve this problem in this video.
View new Dyson filters at Amazon: www.vacuumtester.com/go/dyson...
Read more: www.vacuumtester.com/dyson-bl...
Subscribe here to my channel: / vacuumtester
See more at vacuumtester.com and follow me on social media:
Website: www.vacuumtester.com
Facebook: / vacuumtester
Twitter: / vacuumtester
Instagram: / vacuumtestercom

[@Vacuumtester]

Hey everyone! I made a new video about fixing a Dyson with a blue light, because this video previous doesn't cover all the different Dyson models!🙂
WATCH PART 2 HERE: th-cam.com/video/wHo_ooitfYk/w-d-xo.html and don't forget to subscribe to my channel! ❤

[@jochemvroom589]

Thanks!

[@SeekinSerene]

I didn’t know there was a red light to begin with (mine is blinking blue, not turning on), and I watched a video on an older model and thought I was going to have to carefully take a screwdriver to open and inspect the larger filter on mine too, so all of this is very much appreciated.
I like that you got straight to the point, too.

[@kevinprivet5942]

'pet dander', what the duck are you dribbling about?

[@songbirdhomestaging534]

Thx

[@philipocarroll]

I found a Dyson battery in the recycle bin with a blue light flashing. Basically if you push the button the blue light flashes ten times then off. I pulled it apart to see its charge state and voltage. I found it was 24v which is full charge but it won't deliver any power so this is a charge board fault.

[@samfish6938]

you can wash the blue filter with warm water then let it dry then install

[@Ecksterphono]

Blue light also indicates temperature issue and constantly run on max mode with powerbrush running. This should only be temporarily used. Use max mode only with the wand removed and use with the non motorized attachments when your doing cleanups like the couch ( pretty much dust buster mode) or using the crevice tool. Don't vacuum a floor on constant max suction. Whether carpet or hardwood. Max suction only increases by 5cfm and just turns the direct drive powerbrush a bit faster. To reset this issue. Set the max mode switch to normal. Push the trigger for only 2 seconds then place it on the charger so you have a solid blue light. While on the charger hold the trigger for 15 seconds and let go. Then allow the charger to fully charge the battery. Once the light goes out, you can use the vacuum. Beware though, heavy use and also not servicing the cyclone canister from time to time, dirty contacts and shorts or grounds in the powerbrush wiring through the wand and corrosion or moisture from humidity on the contacts due to slight wet vacuuming with the vacuum will cause these issues to pop up. Every so often disassemble the cyclone separator chamber, separate the gaskets and wash the cyclone components ( minus the foam gaskets in soapy water). Use compressed canned air on the gaskets. To properly clean the cyclone separator canister, it has to be taken apart to clean the caked dust crevices. If you shake the canister and you here rattling, chances are wet pet dander or slightly wet pet dander that hardened is suck in the cones with small hairs. This will also throw codes and cause a lot of resistance in the system on high settings.

[@bhaktilata]

Wow, so helpful, thanks

[@jamesdennis6274]

Thank you so much for this information. It proved to be very helpful! It's greatly appreciated 👍

[@Seren2010kinder]

Thanks that just fixed mine as was turning off after 30 seconds. Thank you

[@lozl1548]

Thank you I was ready to chuck mine thinking it was broke. I didnt know this and fixed it ! Your comment more helpful than video. Thank you for your time explaining. Saved me cost of a new one 👍💗

[@Melimoments]

How to clean Dyson filter

[@yoramweizman3716]

Dayson V11 3 years old+. its dose not show any sign that the battery is low. it just stoped. the lcd is not showing nothing he is black, and the battery is not blinking at all. I tried all the tricks to hold the trigger 10 sec and nothing helps. now it is dead?

[@menalippe]

Experiencing the same right now. Were you able to get it resolved?

[@Demosophist]

The blue light isn't "flashing". It just comes on briefly when I plug in the charger and then goes off.

[@Vacuumtester]

That's a good signal! Means the batteries are charging.

[@andrear5491]

Yes but only charges for 2 mins then it goes off. My machine isn’t even that old so the battery can’t need replacing this quickly

[@pmlam32]

u basically said nothing

[@boxa87]

LOLOL! Glad i wasn’t the only one who thought that

[@skagnatti3415]

My sentiments exactly.

[@Vacuumtester]

@pmlam32 looking back at the Video you have a point; in my early video's the English and the format/filming was my main concern. Getting better at it now though!
If you really want to solve your problem however (8 months late :P ) be sure to check out this article, it gives you all the solutions out there: www.vacuumtester.com/dyson-blinking-blue-light/

[@HeadEnterprise]

Said alot to say a little lol

[@TC-dk6do]

Usless

[@StripedLime]

The blue light is not blinking while charging! What should I do? It is a new unit, not even 6 months old.

[@HMSD11]

I’m having the same problem

[@StripedLime]

@@HMSD11 check the charger
..

[@HMSD11]

@@StripedLime I’ve replaced the charger and Dyson sent me a new body. Replaced that and it still isn’t working. They are now going to send me a new battery. The damn thing is only 5 months old. So incredibly annoying.

[@StripedLime]

@@HMSD11 for a brand; they might as well... do let us know of the outcome. 🤞

[@eboni257]

Me too! $700+ piece of junk!!!