It worked beautifully. Well done sir. I modded this computer up 4 years ago and hated to get rid of it. It is extremely fast as a result. Now I have it back.
Thank you! Did half of what you showed. Didn't remove the processor/cooling part. Just remover the bios battery and touched the metal parts to earth to remove any static. It worked good. Thank you once again.😊
Thank you for showing this technique. I tried it and the laptop starts up as usual. Prior to doing this, took it to a repair place where they have "geeks" and was told that the hard drive was bad and needed to be replaced. Thanks again!
I honestly did not think this was going to work, but since it was pretty much toast i figured what the heck. I tried it on my Dell Inspiron 5558 laptop. The only thing I did different was covered the entire motherboard in foil instead of leaving a chip exposed. I used the heat gun and put it all back together and it actually works again. Thanks so much for the video.
"The blanket method" is a temporary solution(it does work, I tried it) for emergency back up(if you are a student, boy are you going to need this...) and you can also run diagnostics, so you can localize your exact problem when in doubt. Sometimes it can be faulty ribbon cable of the keyboard(you still get 7 beeps which indicate cpu issue...), so you need to localize your issue BEFORE you get a screwdriver, a heat gun and start playng. ;)
This help for a short time, i recommend to replace a whole main board.The thermal pad is efficient,put your finger to a naked cooper and then thermopad.Thermopad is much warmer.
no son los capacitores del chip si no los que estan en el costado los que van en la salida y entrada del chip, los que hacen y se encargan de que pase la energia por el
Teaching Death Warning: I hate fake repairmen that learn off of TH-cam then offer services to learn through trial and error at the expense of their customer's expensive electronics! No respectable educated repairman would ever use a heat gun made for removing paint from furniture on an electronic to do a reflow it caused serious damage and even if it accidentally works that heat gun will have a 100-degree temperature difference from one outlet to the next and will have a 100-degree temperature difference for every 1/8 of an inch in height above the chip you are trying to reflow 99% of you will pop the solder below the chip or kill the chip along with a lot of other stuff! NOTE: if you do not hit reflow temperature within +/- 1 to 2 Degrees with a profile ramping up with specific time intervals to ensure even consistent temperature you will likely kill or at very least damage nearby components not to mention killing that GPU or crystalizing the solder below the chip so badly that even re-balling is no longer an option!! Did you not at least take a soldering class before making this video or offering services? STUPID ALERT!!!
I have the same device and the same problem, I did the heating and even reballing but after a while, the problem came back, I heard that in some models you can make the motherboard use onboard graphics instead of the chip, in other words, omit the graphics chip of the circuit. is it a possible option for this model?
Just plug it in, turn it on, let it beep and wrap the laptop in a comforter nice and snug and let run for 20 minutes and unplug and let cool down at room temp. About 10 minutes and plug back in. PRESTO!
@@dawidcieslak6488 yes it works. also try pushing and pulling on the right hinge of your laptop while booting. worked for me. it might be different dependong on ur model, but when i put tension on it then i can boot up. i also had to use this method in this video first, then anytime i need to power it off/on, i will put tension on the hinge and it boots without having to ever resort to re-heating or anything else. I've had both 7 and 8 beeps on the laptop and I'm using it to type this now. inspiron 3537
when u take the laptop apart there was no CMOS battery ! this 7beeps is for CMOS < when you put back the board inside the case you just put the battery back !
I have a Dell Inspiron 3162 notebook. The problem is when I press the power button, the Beep sound appears 5 times short and there is no screen display. But when I turn off the power button and then I turn around with about 5 trial times, my notebook returned to normal and no more sound. The next day when I turn on the sound of the sound of 5 times a beep. And I unload my laptop then I cleaned RAM after that I replaced RAM and press the power button, the sound of my laptop increased to 7 times the Beep. Keep experimenting several times I press the power button then I turn off, my laptop returns to normal. Please solution, sir?
I have a similar recurring problem with my Dell Inspiron desktop, black screen on initial start-up, locks up, needs to be unplugged to restart, then fine.
+ranlando This type of damage is usually caused by overheating. Downloand some temperature monitoring software and make sure your laptop isn't overheating. Good luck!
I am getting single continuous long beeps spaced after 3 seconds each when staring laptop. Also display is black. I had by mistake started a .exe for bios update in windows.. screen went blank in the process and thereafter it never booted amd is giving me the beeps and black display. How could i fix this?
This is too complicated. Just wish u can fix my laptop now. 8 beeps and black screen. Dell technicians told it was RAM prob and few told its keyboard prob. Now its been 8hrs at d dell workshop and hope to get goodnews by tomorrow. Hope they will fix and not destroy!
sir I had Acer gateway laptop it is not able to charge new battery plugged in but the taskbar doesn't show the battery charging wat to do and how to fix
You have a problem with the keyboard. You might have a beached key. Test has turn the laptop without the keyboard and see that there is no longer beeps.
hi friend i have hp 625 notebook the screen colour messed up white is blue is there is solution for this matter ? if you can pls tell me. when plug external monitar colour is fine
Teaching Death Warning: I hate fake repairmen that learn off of TH-cam then offer services to learn through trial and error at the expense of their customer's expensive electronics! No respectable educated repairman would ever use a heat gun made for removing paint from furniture on an electronic to do a reflow it caused serious damage and even if it accidentally works that heat gun will have a 100-degree temperature difference from one outlet to the next and will have a 100-degree temperature difference for every 1/8 of an inch in height above the chip you are trying to reflow 99% of you will pop the solder below the chip or kill the chip along with a lot of other stuff! NOTE: if you do not hit reflow temperature within +/- 1 to 2 Degrees with a profile ramping up with specific time intervals to ensure even consistent temperature you will likely kill or at very least damage nearby components not to mention killing that GPU or crystalizing the solder below the chip so badly that even re-balling is no longer an option!! Did you not at least take a soldering class before making this video or offering services? STUPID ALERT!!!
3 ปีที่แล้ว
Same thing as the Xbox 360 red ring of death and ps3 yellow light of death.
![ไปอยู่ไสมา - ช๊อปเปอร์ โตเกียวมิวสิค [ OFFICIAL MUSIC VIDEO ]](http://i.ytimg.com/vi/sWuVNbRTJbc/mqdefault.jpg)
It worked beautifully. Well done sir. I modded this computer up 4 years ago and hated to get rid of it. It is extremely fast as a result. Now I have it back.
Happy days and glad to be of help. Thanks for watching.
What kind of modifications did u do
Thank you! Did half of what you showed. Didn't remove the processor/cooling part. Just remover the bios battery and touched the metal parts to earth to remove any static. It worked good. Thank you once again.😊
Thank you for showing this technique. I tried it and the laptop starts up as usual. Prior to doing this, took it to a repair place where they have "geeks" and was told that the hard drive was bad and needed to be replaced. Thanks again!
+Dragonmann336 Happy days and glad to hear your laptop is back on the road. Thanks for watching.
I honestly did not think this was going to work, but since it was pretty much toast i figured what the heck. I tried it on my Dell Inspiron 5558 laptop. The only thing I did different was covered the entire motherboard in foil instead of leaving a chip exposed. I used the heat gun and put it all back together and it actually works again. Thanks so much for the video.
Congrats on your fix
Nicely done, a lot better than those videos suggesting people wrap their laptops in a blanket.
+5150Joker Thanks for watching.
"The blanket method" is a temporary solution(it does work, I tried it) for emergency back up(if you are a student, boy are you going to need this...) and you can also run diagnostics, so you can localize your exact problem when in doubt. Sometimes it can be faulty ribbon cable of the keyboard(you still get 7 beeps which indicate cpu issue...), so you need to localize your issue BEFORE you get a screwdriver, a heat gun and start playng. ;)
I did exactly what you did and it works now, thanks
if I'd have known the fix was this simple, I would have done it ages ago
This help for a short time, i recommend to replace a whole main board.The thermal pad is efficient,put your finger to a naked cooper and then thermopad.Thermopad is much warmer.
no son los capacitores del chip si no los que estan en el costado los que van en la salida y entrada del chip, los que hacen y se encargan de que pase la energia por el
Teaching Death Warning: I hate fake repairmen that learn off of TH-cam then offer services to learn through trial and error at the expense of their customer's expensive electronics! No respectable educated repairman would ever use a heat gun made for removing paint from furniture on an electronic to do a reflow it caused serious damage and even if it accidentally works that heat gun will have a 100-degree temperature difference from one outlet to the next and will have a 100-degree temperature difference for every 1/8 of an inch in height above the chip you are trying to reflow 99% of you will pop the solder below the chip or kill the chip along with a lot of other stuff! NOTE: if you do not hit reflow temperature within +/- 1 to 2 Degrees with a profile ramping up with specific time intervals to ensure even consistent temperature you will likely kill or at very least damage nearby components not to mention killing that GPU or crystalizing the solder below the chip so badly that even re-balling is no longer an option!!
Did you not at least take a soldering class before making this video or offering services?
STUPID ALERT!!!
what If my laptop beeps 7 times then after a while beeps 6 times and reboots and does that again with fan on? can I still fix it with this?
I have the same device and the same problem, I did the heating and even reballing but after a while, the problem came back, I heard that in some models you can make the motherboard use onboard graphics instead of the chip, in other words, omit the graphics chip of the circuit. is it a possible option for this model?
Just plug it in, turn it on, let it beep and wrap the laptop in a comforter nice and snug and let run for 20 minutes and unplug and let cool down at room temp. About 10 minutes and plug back in. PRESTO!
Wow, this actually worked lol. I'm aware it's not a longterm fix but enough to get it running again for resell. Thanks!
@@DaBigBlackGirl i hope the buyer knows its history
Seriously, it works?
@@dawidcieslak6488 yes it works. also try pushing and pulling on the right hinge of your laptop while booting. worked for me. it might be different dependong on ur model, but when i put tension on it then i can boot up. i also had to use this method in this video first, then anytime i need to power it off/on, i will put tension on the hinge and it boots without having to ever resort to re-heating or anything else. I've had both 7 and 8 beeps on the laptop and I'm using it to type this now. inspiron 3537
@@quasarproductions2690 I'm trying it now
when u take the laptop apart there was no CMOS battery ! this 7beeps is for CMOS < when you put back the board inside the case you just put the battery back !
I have a Dell Inspiron 3162 notebook. The problem is when I press the power button, the Beep sound appears 5 times short and there is no screen display. But when I turn off the power button and then I turn around with about 5 trial times, my notebook returned to normal and no more sound. The next day when I turn on the sound of the sound of 5 times a beep. And I unload my laptop then I cleaned RAM after that I replaced RAM and press the power button, the sound of my laptop increased to 7 times the Beep. Keep experimenting several times I press the power button then I turn off, my laptop returns to normal. Please solution, sir?
Hi, is this a way for ever? Or a confident way?
Hello I have Dell (Inspiron 15) 3521 does not turn on the display just the fan and the lights makes 1 long beep and 1 short beep
How long do you heat it up for? On high or low heat?
As soon as I heard the beeping I thought: The ram is missing.
Look up the beep codes from Dell, memory is 4 beeps, video is 7 beeps.
I don't know anything about computer but I have one doubt if my laptop gpu Intel hd 4000
.
.
Can I be able to repair the laptop by using your method
I have a similar recurring problem with my Dell Inspiron desktop, black screen on initial start-up, locks up, needs to be unplugged to restart, then fine.
+ranlando This type of damage is usually caused by overheating. Downloand some temperature monitoring software and make sure your laptop isn't overheating. Good luck!
Thanks!
bro i have dell m6600 + quadro 4000m. when i plug in charger then my screen goes black and hang with restart laptop. do you'll any solution ?
I am getting single continuous long beeps spaced after 3 seconds each when staring laptop. Also display is black. I had by mistake started a .exe for bios update in windows.. screen went blank in the process and thereafter it never booted amd is giving me the beeps and black display. How could i fix this?
My dell inspiron 3520 laptop starting on and go off quickly. Windows installed few days ago, but problem became a starting. What i do.
Can i use a hairdryer?
This is too complicated. Just wish u can fix my laptop now. 8 beeps and black screen. Dell technicians told it was RAM prob and few told its keyboard prob. Now its been 8hrs at d dell workshop and hope to get goodnews by tomorrow. Hope they will fix and not destroy!
Guess will not buy DELL anymore. Trying other brand soon if my inspiron 7000 cannot be fixed.Any recommendations?
LCD failure
CPU failure, in some of the new machine the CPU is soldered into BGA and not a ZIF socket.
I put it on front of a room heater with coil worked as same :)
help me i found 0V in PL600 and 0V in PL700, where is the problem dell 3521
how much is it if you sell a laptop like that? im thinkin of selling mine same modell same problem
sir I had Acer gateway laptop it is not able to charge new battery plugged in but the taskbar doesn't show the battery charging
wat to do and how to fix
I changed the battery but still beeping. what else could be?
He said the chip not battery
Upto what temprature we should heat it
i have a same problem but laptop is dell inspiron m731r-5735 how can i fox it
mine beeps 7 times AND the keyboard doesnt work
The guy said it would ve cheaper to buy a new one
Haven't got one yet
What sucks is that computer was my Christmas gift
Idk
mine beeps endlessly with no breaks what does this mean?
Thanks so much boss
You are welcome, thanks for watching
My laptop its fucking working, thank you so much, subscribed, thumbs up
can i use hot air gun?
my Dell inspiring 15 3537 7 beep error won't starts ..
Hi i have Inspiron 15 it's a touchscreen laptop and it's making 7 beeps same as this one please help it's not starting
Is it working niw
hello i have a dell N5050 and i have this beep problem , when i turn it on the beeps doesn't stop(about 160 beeps !)
You have a problem with the keyboard. You might have a beached key. Test has turn the laptop without the keyboard and see that there is no longer beeps.
But it again given beep after 15min .
can I use hair dryer?
no, not hot enough. trust me, you need 450 F to melt solder.
William Williams d
Thanks!
hi friend i have hp 625 notebook the screen colour messed up white is blue is there is solution for this matter ? if you can pls tell me. when plug external monitar colour is fine
Check out my video on HP laptop pink is black. Good luck!
thanks
Excelent
Thanks for watching
why does this happen
How did you remove the gpu ..
GPU not removed, just reflow
Sir hamara leptop dell Inspiron n 5030 on nahi ho raha hai please help me
Teaching Death Warning: I hate fake repairmen that learn off of TH-cam then offer services to learn through trial and error at the expense of their customer's expensive electronics! No respectable educated repairman would ever use a heat gun made for removing paint from furniture on an electronic to do a reflow it caused serious damage and even if it accidentally works that heat gun will have a 100-degree temperature difference from one outlet to the next and will have a 100-degree temperature difference for every 1/8 of an inch in height above the chip you are trying to reflow 99% of you will pop the solder below the chip or kill the chip along with a lot of other stuff! NOTE: if you do not hit reflow temperature within +/- 1 to 2 Degrees with a profile ramping up with specific time intervals to ensure even consistent temperature you will likely kill or at very least damage nearby components not to mention killing that GPU or crystalizing the solder below the chip so badly that even re-balling is no longer an option!!
Did you not at least take a soldering class before making this video or offering services?
STUPID ALERT!!!
Same thing as the Xbox 360 red ring of death and ps3 yellow light of death.
My dell motherboard does not have that particular chip
Me eather what should I do?
At the most important part of the process, you switch the volume off and speed up the video. Unreal.
My dell inspiron 530 does 3 beeps or 4 beeps
www.dell.com/support/article/us/en/19/sln293445/understanding-beep-codes-on-a-dell-desktop-pc?lang=en
I prepared my motherboard with aluminium , now i heat it
Well know ik what my laptop has... I guess i cant fix it on my own and need to take it to a profecional
miguel briseno Im glad this video helped you understand the problem that you have and what needs to be done. Thanks for watching.
do you know around how much it will cost to fix this?
miguel briseno To have the GPU reballed you're looking at around $100. Please note do not waste your time reflowing the GPU. Good luck!
Mine beeps 4 times
then it is a different problem, and it is not because of this
Re: Hi! Can someone help me? I’ve been tried to resolve this problem: EPSA: Build 4306.21 UEFI ROM - What is this error message? t.co/vKKcXt7iHk
Lol this joke , a 7 beeps error on a dell laptop IS a CPU failure. Not a problem with gpu.your vidéo IS a Fake
Hi, is this a way for ever? Or a confident way?
hi i have dell laptop.it has no power .can you help me to find out this problem