*I like how quiet it is, how well it works and **Fastly.Cool** , This was perfect to help air out a guest room and to use instead of AC when I only want one room kept cool. Works great!*
5 years and counting on helping people like me who knew NOTHING about floor fan fixing until watching this. Thanks for saving me $40 on a new one! I used WD 40 and it worked like a charm (in case anyone is wondering about grease type.)
Thanks for the tip going use it. Here is one in return the piece of plastic he's pointing to @2:00 broke on my unit in the shaft. You need that peice to get the fan to rotate properly. I found that the screw securing the fan to the stand fits the hole perfectly so screwed it in and now it works perfectly. Next problem is how to replace the screw I just found a wood dowl to stick in its place after drilling it out. This sucked wouldn't recommend did it cuz covid made imposable to go get new screw.
WD evaporates quickly so a non-detergent oil or 3-M Fan Oil is better. My electric motor/fan guy never uses grease. Also there is wicking material around the bushing shell that sometimes needs replacing and some amount of oiling to prolong the lubrication servicing.
Great Vid, helped me Fix some old floor fans i was about to toss, now they are flowing like new.....I used some high quality silicon lubricating grease worked quite well....thanks a lot!
THANKS - YOUR video was very helpful IN REPAIRING a FLOOR FAN that is over 20-years old. the FAN belongs to my Son and - OBVIOUSLY - has MORE SENTIMENTAL VALUE than ACTUAL WORTH. For those that are CURIOUS the SHAFE of the MOTAR was VERY DIRTY. I cleaned the shaft as defined in the video and I removed the old grease - which after 20-years was still PLIABLE. I cleaned the parts and I install new GREASE. I do not remember the FAN working this WELL and being so QUIET. THANK YOU !
Mine was a tab different in where the parts were. The hub bearing was actually out of the rear part of the motor. I must've tried to put it together like that and it wasn't until I watched three videos showcasing the same thing like no fan blade spin So thanks to your video I was able to figure out where I was going wrong. So in the rear I just had to lift up three tangs and put the hub bearing in there snug as a bug in a rug. LOL :)
great video, man. But somehow the shaft of my fan became even more stuck. I must have done something wrong, I will disassemble and assemble it again. Thank you
This video gave me almost all the intel I need to fix my high velocity floor (Chinese) fan. I took apart my 'pedestal' fan similar to the one in this video last year & cleaned it up & changed some grease but I missed something & it didn't oscillate correctly & made a noise on high. I opened it again today to realign it. A tiny plastic nub where the motor sits was not seated. It's not made like anything I've seen on TH-cam. (It's so well made it gives me confidence that I can't screw it up. if I pay attention) To be fair I should tell you more about it, it's very cute pink & white plastic with transparent pink blades & the front & back grills have a thick plastic coating so they won't corrode. One tiny pink lever in the trim opens the front grill to remove it for cleaning & a big fat knob turns counterclockwise to remove & wash the blade assembly (1 piece) The wires off the motor coil feed into a plastic grill assembly sitting fitted over the coil. All the connections are soldered into paddles fitted on the grill. The thermo-protection unit snaps onto the side of the grill. Did I mention this is the very first time my fan has needed attention? I bought it in Japan in early 1987. It's so well made it almost pisses me off.
I had an oscillating Westinghouse desk fan from around 1954 that was still working, that I bought at a garage sale back in the 1980s. I donated it to a museum three years ago. Along with the fan, I also donated an early ‘50’s “owl eyes” Zenith clock radio (also bought at a garage sale in 1980s), and a 1955 Sears Kenmore toaster that my dad bought new. Both of them also were working.
Hmmm this is 2022. My fan stopped working... I was set to buy a new one tomorrow and something told me to check TH-cam and I found this. Save me some hundreds. Thank God
3:34 See those little blobs in the bushing area? They need to be removed and something like oil lamp wick used to replace it by pushing it in around the bushing journal and adding a goodly amount of machine oil to soak it to improve lubrication and extend service intervals. The biggest problem is slow, stuck propeller shaft due to low lubrication and resulting dry bushing and shaft surfaces. I noticed those loose blobs many times while re-servicing all too often dry fan bearings in a hot dusty climate. That material is insufficient to work well to hold oil near the bushings, whereas the ones I replaced with oil lamp wick are still working fine. Don't forget, capacitors lose power over time and need replacing after a while. If lubrication doesn't restore fan speed replace the capacitor.
Me watching after I gambled it yesterday just like in this video i knew nothing about fans but I did it just like this and it's blowing air on me right now 😂😂😂
I used oil that came with my shaver, spent at least 2 hours on the whole project and did a great job in my own opinion ... but the fan has only been running smoothly for a couple of days after that ... now I still have to "start" it manually otherwise the blades won't rotate. >:-(
About a teaspoon of oil, to saturate the felt around the bushings. 20 or 30 weight non detergent oil. Blue "3 in 1" oil, made for electric motors, seems good, (or equivalent). I use 30w non detergent oil. About $3 per quart at Walmart. Use a dropper to apply. I'm not an expert. This is the best info I've found. And it works for me.
Yeah, i did this and now it doesnt work anymore. Before it was just spinning slowly, I followed your instructions and now the motor wont turn on at all.
Any idea what's happening with my identical fan? It spins freely by hand, but there's no power. I checked all electrical ends and 120v goes all the way to the stator. No buzzing or any noise at all.
Question: I took mine apart and cleaned everything with WD-40 and lubricated it with oil. Before it hummed a little, while not able to turn. Now I can turn it easily with my fingers, but there seems to be no power or hum. I reassembled it carefully, so the unit should be mechanically correct. Is there any issue with getting WD-40 or oil on the coil? Should I take it apart again and wipe it down good with paper towels? Any other ideas?
Wires in the motor coil are varnished, oil shouldn't affect those, otherwise a good idea to keep stuff clean. Hum & no turning: that's how a seized bearing burns down the motor. It may be dead.
I used baby oil to lubricate the shaft and bearings in my fan motor today and it works like new again. Is it okay to use baby oil for a job like this? It's the only type of oil I had on hand.
+Benjamin “Ozias” Esposti Right. Ball bearings are too expensive, so say the owners at the Foshan Guanmei Electrical Co., Ltd factory in Guangdong, China and feel they need to produce new throw-away items cheaper than the competition, never better or longer lasting.
Nice video. Do you know where I can find a replacement fan motor for an older model Lasko Box Fan with the larger "deeper 20" box" ? I'm having trouble finding one. Thank you.
Thanks. I did clean the shaft. . But when I put the stator and rotor . Still it makes some noise without moving. .pls any tips. I don't know if it is the rotor or the stator. Pls pls .
@@theoverengineer thanks for replying. But is making sound. Like the rotor is too small to occupy the stator. But when u press the rotor. It start to rotate little by little
Sir mera wall fan jam ho jata hai jaise hi on karta hun...aur vibration ka sound ata hai...jab main electricity band karta hun to shaft freely ghumta hai...please suggest ki on karne pe hi kyun jam hota hai...
How long was running with grease up before the next fix? My opinion this bushing called oil shintered or oil immersed self lublicating bush, with synthetic oil.
The spherical bushing in my fan came out of the housing when i was pulling apart the rotor and shaft. I tries hitting it with a hammer but it doesn't want to go back. Also how to remove the little metal stick on the shaft where the fan blades sits. That thing doest let me take apart the whole fan. Maybe i get the busing into the housing if i can take out the shaft.
I have same motor but shaft is moving back and forth instead spining in place.I opened it and found nothing unusual.I expected maybe some broken spacer but nope.Is there any fix to it?
Hello, turning very hard ? using motor with ball bearings, then will be working easily without this problem. This fans have very frequently problem with plain bearigs.
theoverengineer : I have a similar floor fan ... after cleaning the hub/bushing ... (I thought that might be the problem) ... when I turned on ... it buzzes and blocks the rotor very very hard ... you can't move the rotor by hand ... I pull the cap ... checked ... and it seems to be fine ... around 1.8 uF. When you turn off the fan ... you can move the rotor very easily ... what could be the problem? It does it at any speed. Thanks.
Yes ... the front bearing ... when you pull it out ... it's a pain in the neck to put it back ... but now that the part is free ... I noticed the bronze bearing on the back. It disappeared too ... and when you start the motor ... the coil pulls the rotor back ... if you push the rotor shaft forward with a flat blade screwdriver ... then it starts spinning ... like new. .. But here is the problem ... where will you get those bearing parts from? ... I'm thinking ... maybe ... I need to put a real ball bearing ... they are cheap and easy to find I know ... a lot of people are thinking ... why bother? ... just throw it away The mindset of throwing everything away ... does not allow your brain to think about problem solving ... I must say that better than that, is when you develop a mindset of being a person with a patience to study the situation that allows for planned solution including the throw it away!!!
Exactly the point of this channel. I often get `spare`parts from thrown away items. Never came across those bearings new. Sub in something that fits, shoot a video on how it worked out and post a link here.
I just got a fan that is super loud, any way to make it less loud? On level 1 it is just so loud i cant hear the TV, and on 3 even worse. Is that normal for new fans and it will go down, or can i lower the noise by screwing on something?
@@theoverengineer the fan actually works well, the issue is that on speed 1 it sounds like speed 3, and on speed 3 it sounds like speed 6 (even thought it only has 3 speeds). Is there a way to open up and lower the fan speed somehow? I have to take it in to the repair shop otherwise. Thank you for your help!
@@theoverengineer Is there any way to open it up and lower the voltage somehow? Or i have to take it in to a repair shop or similar? For the person without engineering skills i mean. ;)
Even if its cheap and ugly, it can still blow air even not much, in my country, chinese made fan uses 1.2 uf capacitor, but this one uses 2.5 uf one, even if its blow no thing, it can still do the job to move air
Note: I know some of us may think, I'll use car transmission fluid or brake fluid as that's the only lubricate I have but 1) From the research I've made, they may be corrosive and mess up the metals in the fan 2) I already tried them but they work ONLY temporarily (after some minutes your fan will be slow again. I guess you need OIL not other fluids
Good one works for a few days and back to take it a part again till you brake the thin coil wire, and you done. so far none of the oil, grease idea worked for me. Oil dry and burns as in the frypan, make it sticky.
@@theoverengineer yes my fan blade has a bit of a crack and just fell off last night. we bought a new fan, but i still want to fix the old one, i've been taping the blade up cause i coudn't find a replacement , it's a steel fan btw :) thank you so much for getting back to me.
Then why isn't the oil that came with my shaver doing the job? I cleaned the old stuff off first and everything. The question is not whether it worked initially, cause it sure did, but after just some days, the blades are almost too stuck for the fan to start rotating on its own... This has happened with both my floor fan and table fan.
![[TH] JFT vs RLF - VCT Ascension Pacific - Day 2](http://i.ytimg.com/vi/PuIH7w_jO6c/mqdefault.jpg)
*I like how quiet it is, how well it works and **Fastly.Cool** , This was perfect to help air out a guest room and to use instead of AC when I only want one room kept cool. Works great!*
Glad I could help!
5 years and counting on helping people like me who knew NOTHING about floor fan fixing until watching this. Thanks for saving me $40 on a new one! I used WD 40 and it worked like a charm (in case anyone is wondering about grease type.)
You're very welcome and thank for sharing your tip!
Thanks for the tip going use it. Here is one in return the piece of plastic he's pointing to @2:00 broke on my unit in the shaft. You need that peice to get the fan to rotate properly. I found that the screw securing the fan to the stand fits the hole perfectly so screwed it in and now it works perfectly. Next problem is how to replace the screw I just found a wood dowl to stick in its place after drilling it out. This sucked wouldn't recommend did it cuz covid made imposable to go get new screw.
I gr
WD evaporates quickly so a non-detergent oil or 3-M Fan Oil is better. My electric motor/fan guy never uses grease. Also there is wicking material around the bushing shell that sometimes needs replacing and some amount of oiling to prolong the lubrication servicing.
non detergent oil only.. never wd or motor oil gum it up.. do it right
Great Vid, helped me Fix some old floor fans i was about to toss, now they are flowing like new.....I used some high quality silicon lubricating grease worked quite well....thanks a lot!
Thank you man.air now is fresh for me with this very high temperature. Fan fixed now and work perfect.
Thank you so much for placing this video on TH-cam....I was able to fix my friends fan. God bless you.
Very good job! I have a $100 table fan Vornado that I need to fix. I love people who fix things and put them back in service!
Well i service old fans
You doubtless found a video to fix your Vornado fan!
Thank you, great video. I was able to fix a super squeaky, slow to no spinning fan.
THANKS - YOUR video was very helpful IN REPAIRING a FLOOR FAN that is over 20-years old. the FAN belongs to my Son and - OBVIOUSLY - has MORE SENTIMENTAL VALUE than ACTUAL WORTH. For those that are CURIOUS the SHAFE of the MOTAR was VERY DIRTY. I cleaned the shaft as defined in the video and I removed the old grease - which after 20-years was still PLIABLE. I cleaned the parts and I install new GREASE. I do not remember the FAN working this WELL and being so QUIET. THANK YOU !
You're welcome!
Can you film a vid of that stand fan, i also have a stand fan from the mid 80s
I was going to throw out my fan but it is now working perfectly thanks to your amazing video. Thank you so much.
Nice work, mate!
My fan was sitting on the curb for 1 day brought it back in and low and behold the fan is back in it's rightful place! Mahalo🙌🌺🍹
Thanks for a superb video! Add another to your already extensive list of vicariously resurrected floor fans!👍
Mine was a tab different in where the parts were. The hub bearing was actually out of the rear part of the motor. I must've tried to put it together like that and it wasn't until I watched three videos showcasing the same thing like no fan blade spin So thanks to your video I was able to figure out where I was going wrong. So in the rear I just had to lift up three tangs and put the hub bearing in there snug as a bug in a rug. LOL :)
Nice work, thanks for watching!
OUTSTANDING THANK YOU! Cleaned as you showed fan now works GREAT! Thanks again.
Glad it helped
I love,when we help/educate one another 😊.
I had a replacement all set to buy but going to give this a shot first. Thank you Sir.
Great vid. Was about to throw away mine! Thanks sir!
I love it !! Do you want it to SUCK ? DO you want it to BLOW ? Great Video !!!
Thanks. At 7 : 15 I found there was ascrew to remove in the tiny piece for oscilation to remove the plastic at the back.
great video, man. But somehow the shaft of my fan became even more stuck. I must have done something wrong, I will disassemble and assemble it again. Thank you
Fixed my issue completely! Thank you so much!!!!
Glad it helped!
This video gave me almost all the intel I need to fix my high velocity floor (Chinese) fan.
I took apart my 'pedestal' fan similar to the one in this video last year & cleaned it up & changed some grease but I missed something & it didn't oscillate correctly & made a noise on high. I opened it again today to realign it. A tiny plastic nub where the motor sits was not seated. It's not made like anything I've seen on TH-cam. (It's so well made it gives me confidence that I can't screw it up. if I pay attention) To be fair I should tell you more about it, it's very cute pink & white plastic with transparent pink blades & the front & back grills have a thick plastic coating so they won't corrode. One tiny pink lever in the trim opens the front grill to remove it for cleaning & a big fat knob turns counterclockwise to remove & wash the blade assembly (1 piece) The wires off the motor coil feed into a plastic grill assembly sitting fitted over the coil. All the connections are soldered into paddles fitted on the grill. The thermo-protection unit snaps onto the side of the grill. Did I mention this is the very first time my fan has needed attention? I bought it in Japan in early 1987. It's so well made it almost pisses me off.
I had an oscillating Westinghouse desk fan from around 1954 that was still working, that I bought at a garage sale back in the 1980s. I donated it to a museum three years ago.
Along with the fan, I also donated an early ‘50’s “owl eyes” Zenith clock radio (also bought at a garage sale in 1980s), and a 1955 Sears Kenmore toaster that my dad bought new. Both of them also were working.
Hmmm this is 2022. My fan stopped working... I was set to buy a new one tomorrow and something told me to check TH-cam and I found this. Save me some hundreds. Thank God
Glad I could help
I put grease that I had for my fishing reels and it’s been working like champ for 1 /2 year
[In 30 seconds] = Having the fan horizontally= Put few oil drops on the shaft having so oil can drip ▼= wait 20 second & it is done
Thank you, I am motivated to fix my fan
3:34 See those little blobs in the bushing area? They need to be removed and something like oil lamp wick used to replace it by pushing it in around the bushing journal and adding a goodly amount of machine oil to soak it to improve lubrication and extend service intervals. The biggest problem is slow, stuck propeller shaft due to low lubrication and resulting dry bushing and shaft surfaces. I noticed those loose blobs many times while re-servicing all too often dry fan bearings in a hot dusty climate. That material is insufficient to work well to hold oil near the bushings, whereas the ones I replaced with oil lamp wick are still working fine. Don't forget, capacitors lose power over time and need replacing after a while. If lubrication doesn't restore fan speed replace the capacitor.
And if the shaft has wear marks it might not run right either ~ tricky stuff!
Me watching after I gambled it yesterday just like in this video i knew nothing about fans but I did it just like this and it's blowing air on me right now 😂😂😂
I used oil that came with my shaver, spent at least 2 hours on the whole project and did a great job in my own opinion ... but the fan has only been running smoothly for a couple of days after that ... now I still have to "start" it manually otherwise the blades won't rotate. >:-(
Neon
I had a feeling it can be fixed. Thank you for the video it helped. I used bycicle chain lube. Fan work as new :)
Glad it helped!
Clear and to the point, great info! Thanks for posting this video
Glad you enjoyed it!
A top secret fix.. If ur blade comes loose or wobbles.. Put front plastic nut on with a bit of thread tape🚨🚨🚨
That's clever
sure would of been nice to watch u put the grease on it. TY !
About a teaspoon of oil, to saturate the felt around the bushings. 20 or 30 weight non detergent oil. Blue "3 in 1" oil, made for electric motors, seems good, (or equivalent). I use 30w non detergent oil. About $3 per quart at Walmart. Use a dropper to apply.
I'm not an expert. This is the best info I've found. And it works for me.
Thanks for sharing!
Yeah, i did this and now it doesnt work anymore. Before it was just spinning slowly, I followed your instructions and now the motor wont turn on at all.
change out the capacitor......
Any idea what's happening with my identical fan? It spins freely by hand, but there's no power. I checked all electrical ends and 120v goes all the way to the stator. No buzzing or any noise at all.
Question: I took mine apart and cleaned everything with WD-40 and lubricated it with oil.
Before it hummed a little, while not able to turn. Now I can turn it easily with my fingers, but there seems to be no power or hum.
I reassembled it carefully, so the unit should be mechanically correct.
Is there any issue with getting WD-40 or oil on the coil? Should I take it apart again and wipe it down good with paper towels? Any other ideas?
Wires in the motor coil are varnished, oil shouldn't affect those, otherwise a good idea to keep stuff clean.
Hum & no turning: that's how a seized bearing burns down the motor. It may be dead.
I used baby oil to lubricate the shaft and bearings in my fan motor today and it works like new again. Is it okay to use baby oil for a job like this? It's the only type of oil I had on hand.
Any oil. Sometimes I grab cooking oil.
I wish I could take the covers off the back of my fan but it has swivel switch on the fan it's self and not traditional buttons ones
Please I have the same fan
It is working but can stop on it own, what may be the problem
Sometimes work correctly sometimes on and off
A broken wire or bad connection
thanks my man. i like the subtle humour.
thx 4 watching!
my pedestal fan has a new capacitor and the motor is ok but the fan is not running what is the main problem?
Make sure electrons make it to the motor and back to ground (all connections)
Any way to restart the capsitor ? I’ve cleaned the fan in the fan blade turns smooth no power
Not really, it's sealed with epoxy glue
Trash can it is
I'm amazed at the sheer number of recent videos put up online about these fans failing like this.
Poor design! Not built to last!
+Benjamin “Ozias” Esposti Right. Ball bearings are too expensive, so say the owners at the Foshan Guanmei Electrical Co., Ltd factory in Guangdong, China and feel they need to produce new throw-away items cheaper than the competition, never better or longer lasting.
Right. Appliances are made to fail so consumers keep buying them.
theoverengineer akala ko pang mutorsiklo lang marunong din pala mag ayos ng bentelador
Benjamin Esposti no you're wrong if the fan died and you see no fuse in the winding then just change the capacitor.if the fan locked up
The exact fan you using there i need to know where the wires go
wow thanks a lot i fixed my fan after seeing your video
Regards
Any video about the motor wiring cz mine is stuck when turned on but not stuck when torned off (you can spin it by hand). Any idea why ?
Something about plastic fans kills me inside LOL...
Nice video. Do you know where I can find a replacement fan motor for an older model Lasko Box Fan with the larger "deeper 20" box" ? I'm having trouble finding one. Thank you.
Not that I know of
Thanks. I did clean the shaft. . But when I put the stator and rotor . Still it makes some noise without moving. .pls any tips. I don't know if it is the rotor or the stator. Pls pls .
It is making that sound by something rubbing on something, have to find the source
@@theoverengineer thanks for replying. But is making sound. Like the rotor is too small to occupy the stator. But when u press the rotor. It start to rotate little by little
That was funny , that you put the core on backwards on the fan , so it was spinning in the opposite direction.
Sir mera wall fan jam ho jata hai jaise hi on karta hun...aur vibration ka sound ata hai...jab main electricity band karta hun to shaft freely ghumta hai...please suggest
ki on karne pe hi kyun jam hota hai...
How long was running with grease up before the next fix? My opinion this bushing called oil shintered or oil immersed self lublicating bush, with synthetic oil.
Yes, right, 200 hours, then I mixed grease with oil
Thank u very much sir I got mine fix now I will subscribe
Hello i have taken my fan apart and i accidentally cut the wires at the back winding wires to the switch
The spherical bushing in my fan came out of the housing when i was pulling apart the rotor and shaft. I tries hitting it with a hammer but it doesn't want to go back. Also how to remove the little metal stick on the shaft where the fan blades sits. That thing doest let me take apart the whole fan. Maybe i get the busing into the housing if i can take out the shaft.
Check out this model th-cam.com/video/cHco5EOoi88/w-d-xo.html
I have same motor but shaft is moving back and forth instead spining in place.I opened it and found nothing unusual.I expected maybe some broken spacer but nope.Is there any fix to it?
Find what's NOT moving that should, starting at WHERE exactly surfaces touch that shouln't
@@theoverengineer thats the thing,everything look normal
Hello, turning very hard ? using motor with ball bearings, then will be working easily without this problem. This fans have very frequently problem with plain bearigs.
Wait how did you get the plastic off the fan motor? I cannot get it over the finger that you pull out to stop the fan oscillating.
Pull out (up on) that finger thing
Silicone lubricator work well?
can you explain the electrical connection s?
I had some CBD oil laying around and it did the trick lol. I don’t know if it the right oil but a few drops in the bearings and now it works .🤷🏻♂️
You put... CBD oil as a grease oil? Hmm... Seems like a waste of CBD oil to me.
Fan not moving but sound .vaibrasion hot what prbloem
How did you get the top pull off that is the choice of oscillating??
Grab and pull. Go with gorilla power level setting.
thanks ma brother from another mother🤟
Hello! I just did that but my fan still is not sorking, it makes a buzzing sound, so Im sure it's not the motor, what could it be?
condensor /capacitor or short coil
Thanks for the help my is working find now 😊
Great!
I just do what you should and use them to relieve stress.
You and me have very diffrent ways of releaving stress. Lol
Wish me luck. I'm gonna attempt to fix mine. I'm a woman and I really don't like doing these things. 😫
Let us know how it turned out!
hi, any idea how do we change the front bushing/ bearing?
Press-fit into housing, usually held by petal-shaped retainer, made with 5 -9 spring retainer lobes.
theoverengineer :
I have a similar floor fan ... after cleaning the hub/bushing ... (I thought that might be the problem) ... when I turned on ... it buzzes and blocks the rotor very very hard ... you can't move the rotor by hand ... I pull the cap ... checked ... and it seems to be fine ... around 1.8 uF. When you turn off the fan ... you can move the rotor very easily ... what could be the problem? It does it at any speed. Thanks.
Bearing misalignment. Bearings are worn to the point they can't keep clearance between rotor and stator.
Mmmmmm...meaning..the bearing..are basically...part of the shaft...meaning...the fan is over!!!
Thanks
Yes ... the front bearing ... when you pull it out ... it's a pain in the neck to put it back ... but now that the part is free ... I noticed the bronze bearing on the back. It disappeared too ... and when you start the motor ... the coil pulls the rotor back ... if you push the rotor shaft forward with a flat blade screwdriver ... then it starts spinning ... like new. .. But here is the problem ... where will you get those bearing parts from? ... I'm thinking ... maybe ... I need to put a real ball bearing ... they are cheap and easy to find
I know ... a lot of people are thinking ... why bother? ... just throw it away
The mindset of throwing everything away ... does not allow your brain to think about problem solving ... I must say that better than that, is when you develop a mindset of being a person with a patience to study the situation that allows for planned solution including the throw it away!!!
Exactly the point of this channel. I often get `spare`parts from thrown away items. Never came across those bearings new. Sub in something that fits, shoot a video on how it worked out and post a link here.
I just got a fan that is super loud, any way to make it less loud? On level 1 it is just so loud i cant hear the TV, and on 3 even worse. Is that normal for new fans and it will go down, or can i lower the noise by screwing on something?
Find the source of noise: blades hitting grille? blades cracked/damaged/unbalanced? bearings?
@@theoverengineer the fan actually works well, the issue is that on speed 1 it sounds like speed 3, and on speed 3 it sounds like speed 6 (even thought it only has 3 speeds). Is there a way to open up and lower the fan speed somehow? I have to take it in to the repair shop otherwise. Thank you for your help!
I see. Too high voltage.
@@theoverengineer any way to regulate that without taking it in to the repair shop?
@@theoverengineer Is there any way to open it up and lower the voltage somehow? Or i have to take it in to a repair shop or similar? For the person without engineering skills i mean. ;)
It's working brand new
Cleaned mine but still not rotating. Maybe something else is dead
Can I clean with alcohol or spirits
Sure do as long as it dissolves the type of crud accumulated on the shaft.
My fan spins on 1,2,4,5. Doesnt spin on 3 and 6.. any suggestions?
Contact problem inside the switch
Buy beer
Very nice.
Nice insight
Can use this motor for my bike
Good video... 👍
Can anyone tell me how much watts is that motor?
Hi my fan motor was changed but there's no.speed on all 3 modes
Test motor for continuity. Test switch for continuity in all positions. If both check out, find the open at the wire connections.
Even if its cheap and ugly, it can still blow air even not much, in my country, chinese made fan uses 1.2 uf capacitor, but this one uses 2.5 uf one, even if its blow no thing, it can still do the job to move air
Normally do fan get heated
Not at all
Thank u Sir..
Yea
umm....where is the Thermo-resistor??
Note: I know some of us may think, I'll use car transmission fluid or brake fluid as that's the only lubricate I have but
1) From the research I've made, they may be corrosive and mess up the metals in the fan
2) I already tried them but they work ONLY temporarily (after some minutes your fan will be slow again. I guess you need OIL not other fluids
totally
change the capacitor
a dab of high temp grease or at least a light machine oil , such as used on guns and sewing machines
Good one works for a few days and back to take it a part again till you brake the thin coil wire, and you done.
so far none of the oil, grease idea worked for me. Oil dry and burns as in the frypan, make it sticky.
My Wall Fan Had The Same Problem
Got mine fixed at wallmart.... self pay
if you Use Machine Oil, in 1 week it will be stuck again ..
I am working on a prototype tornado siren, and im making it out of a fan like this.
DoctorWhoRoblox1935 dude I’ve allways wanted one I could see how you could make one from a fan, that’s sick
Help, my fan's been shaking. And it's whole body is literally vibrating and shaking so bad..
Chipped fan blde or off-center mounting, could be due to bent fan shaft.
@@theoverengineer yes my fan blade has a bit of a crack and just fell off last night. we bought a new fan, but i still want to fix the old one, i've been taping the blade up cause i coudn't find a replacement , it's a steel fan btw :) thank you so much for getting back to me.
I did this and now it won't spin?
That sucks. Geometry is finicky.
I need idea like this
i cleaned mine. . . now it spins in counter clockwise, rendering it useless....
Wires got swapped around when they got disconnected. Find it where and connect the motor so it rotates right.
Why buzz sounds is coming when switched off and motor heated
Something arcing inside, warm components nearly close normally open gaps.
@@theoverengineer so what is the solution? i tried cleaning but didnt work. still buzzing.
What kind oil
For a fan of this size, any kind, even from the kitchen, canola, coconut, palm, anything. Benefit: washes out of clothes is spilled.
Then why isn't the oil that came with my shaver doing the job? I cleaned the old stuff off first and everything. The question is not whether it worked initially, cause it sure did, but after just some days, the blades are almost too stuck for the fan to start rotating on its own... This has happened with both my floor fan and table fan.
Thank you sir!
04:46
Armature is gummed up