Ways to Install an Outdoor HD TV Antenna for Best OTA TV Reception
ฝัง
- เผยแพร่เมื่อ 7 ก.ย. 2024
- In this video I provide six ways you can mount and install a TV antenna outside on the trim of your roof, chimney, and exterior wall. An outdoor "Digital" HD TV Antenna Setup will get you the best reception and most channels possible compared to an indoor antenna.
Link to recommended antenna masts:
www.amazon.com...
Video on how to properly ground an antenna:
• How To Ground an Outdo...
Check out my Amazon Page for recommended antennas and accessories:
www.amazon.com...
For an antenna recommendation visit my website:
antennamanpa.c...
Considering a Channel Master antenna? Use my affiliate link below:
www.channelmas...
🔌 Did my videos help you cut the cord? If so, consider a PayPal contribution, Patreon, or a Channel Membership: www.paypal.com... / antennaman
Sign up to my e-mail list:
bit.ly/2whSoTI
Like my Facebook page:
/ antennamanpa
E-mail brief general questions or sponsorship inquires to theantennamanpa@gmail.com - before sending an e-mail consider a custom antenna recommendation below if you are looking for help with an antenna setup.
www.antennaman...
Note: this video and description contains affiliate links, which means that if you click on one of the product links, I'll receive a small commission.
📡 Affiliate Link to recommended antenna masts:
www.amazon.com/shop/antennaman/list/WC4S8JKO3XA2?ref_=aip_sf_list_spv_ofs_mixed_d
📡 Affiliate Link to recommended antennas, amplifiers, and other accessories:
www.amazon.com/shop/antennaman
Where's the Chimney Mount?
@@user-dj8yo6nj1n When I worked for Bell in the microwave group, we used to do that for temporary TV shoots with 5 foot 2 gig dishes but would not recommend that for something permanent. Also we only did that on flat level roofs.
Thank you. Looking at that, I think I have one somewhere.
The sturdy j pole is showing as out of stock. Any alternative? Would it be sturdy enough to hold a channel master cm-3020 ?
That link for the 10ft pole is actually for a 10 inch pole (Product is 10 inches in length and 1. 5 inches in diameter.)
I totally agree on NOT drilling into the roof and installing the tripod mount. Thank you for posting this video.
We had a tripod (+guy wires) on our 64 element VHF and UHF yagi stacked on a 18' mast + heavy Channel Master rotor in Detroit (snow-covered roof often). In 15 years our roof never leaked. I think my dad put so-called "dum-dum putty" (flexible thick gray stuff) in and around the mounting bolts.
@@JoeKaye-hn5dt Yeah, but most do-it-yourselfers would probably not do a proper job and end up with leaks. Too many ways to mess it up.
@Manny Yep. My brother installed my antenna with a tripod mount. But he was a satellite installer at the time and did it right.
Absolutely. Here in Florida the insurance companies look for ANY excuse to question the integrity of your roof and drop your home owners policy.
I put up my own antenna 5 years ago and love it. It has saved me a boat load of money rather than paying for cable TV. I get more channels and for free.
You are absolutely correct regarding flimsy chimney straps. I'm a HAM operator and have had experience with both good and bad products so care is definitely needed in choosing equipment.
"Carry a bigger hammer" is the only mantra when installing a antenna❗
You don't want to have to do it again after a ice or wind storm!
And don't try to cheap out. Plumbing parts, auto parts, trying to go on the cheap will hurt you.
What I did is i reused the old DirectTV dish bracket and mount/mast after removing the dish I was able to re use my houses coax lines and I get great signal here in the Orlando Area here in Florida. best part is the mount was already grounded and the ground wire for the antenna itself was already in place just had to remove it from the dish and move it to the antenna. Purchased a nice multi output signal booster and I get great TV reception, Great FM radio reception and great reception on my Noaa Weather Radio. Plus side is I didn't have to run new wires. Just had to trace em out using my coax line toner/tracer and take out old spittlers and other DirectTV stuff that the last owners of this house left behind and I was enjoying great FREE HD!
Another item to consider: If you live in the winter snow belt, be aware that your antenna WILL pick up snow and ice that will add significant weight to the installation. Be sure that the mounting surfaces are robust (no thin or rotting wood) and that the bolted mounts are extra secure. Also, secure the cable to the mount so that the cable weight is not solely supported by the antenna. An ice coated cable is easily capable of warping a lightweight aluminum antenna.
VERY good point about supporting the cable. Presumably, also leave enough slack to accommodate movement of the antenna in the wind.
Good video.....I was surprised that you didn't mention that most J-poles are used by satellite dish companies. So not only can they use the already installed pole mount, they can easily connect the old dish cable onto their cable to have it run into the house with ease.
Yes, I agree.....I use my old satellite coax cables and, I removed the head from the arm, mounted my antenna directly in front of my satellite dish and get better reception from the dish itself. I tested it without the dish, I got decent reception, then I mounted to the front of the dish and, got excellent gain. The difference was without the dish 68.9% gain, with the dish it was 97.4 %, this is what my signal meter showed. In fact I could not get PBS tower without the dish due to the fact it was 30 degrees in a different direction from my other broadcast towers, with the dish, it picked up 3 different PBS stations. It's really amazing why more people don't think about this method because the cable are also Quad-Shield coaxial cables, plus the dish is already grounded 75 Ohms to my electrical box.
My tv-antenna is set up yet still watching your vids✌🏻
Something about chimney mounts: Chimneys might look solid and they might look like they can bear a lot of weight but it really is a bad idea to tax your masonry like that. For example my house had a masonry chimney with a large television antenna when I purchased my house in 2005. The chimney was detached already, but I'm pretty sure having the extra weight of the antenna didn't help and it slowly moved a little more each year. I had the chimney demolished and replaced with a box in 2019. The guy I hired to demolish and replace the chimney said that he had to man handle to keep the whole thing from falling down all at once after the flashing was removed.
Yes, my parent's house had a chimney mount going back to the 1950's. I noticed in 2011 that their chimney was in very bad shape; it even had some bricks sliding out of place. I found a good chimney repair crew that rebuilt the bricks so the whole thing wouldn't topple off of the roof.
Old ones are easy to push over the mortar no longer stick it together my old Victorian house had 5 chimneys. All of then had to be rebuilt that house had a slate roof too if one fell it would have cost a lot for repairs !
+1 for the channel master mount! Used it for my setup. It's one of the few mounts I found where you can also adjust the yaw angle of the pole. I had to mount mine slightly below the roof peak on the facia and with this mount I was able to get it vertically straight. With the extendable pole, the antenna is about 2 feet above the peak of my house with a clear line-of-sight.
I saved over $200 dollars with an antenna ( the bad one) and a call to Verizon.
Thanks A Man
btw the way.The rotor is crazy. That and the cat thinks it's a toy and changes it.
My man the antenna man. You are so correct on everything you describe. As a satellite antenna installer. We fallow the same rules and requirements as you do. He is a Proffesional antenna installer. And as ham radio operator. He also correct when it comes to making a custom antenna as well. I am not going to go through all the things he must do make a custom antenna. Because this comment will be very long. But I can say this. He will save you more money than if you try it on your own. And he will get you more channels than you would if you try it on your own.
Why do I watch this video and I am in an apartment? Because I always learn something from your videos.
Thanks for watching!
Have you reviewed a Dennys Stacker Antenna? Thank you Brian
@@brianhilkert7955 I am waiting on contributions to help with the cost. Lots of viewers but very few contributing. If you'd like to help with the cost the link is below:
paypal.me/pools/c/8cwRt7M0g4
Regarding the tripod. We install tripods quite frequently. We use a good mastic tar pad with nine 1/2" head lag screws that are either 2 1/2 or 3" long. We've been using them for decades. Never had a leak problem and never had one blow over or break (VERY windy in Michigan). I agree that caution is to be used here, but it's definitely a viable option. I also read somewhere in the comments that you HAVE to make sure all your lags hit rafters. Also, not true. As long as you're using solid, legit lag screws (not 1/4" ones), you'll be fine. Love your videos.
I love the FCC Repack. I just recently got 4 new channels with great signal strength! Thank you Antenna Man got keeping us up to date with the Repack!!
I discovered that when I moved my antenna to the other side of our double wide, I received more channels and found 2 new stations. Thank you for the video
What about the method of a pole from the ground mounting the antenna. Ours growing up was dig a hole,put a brick in it to set the pole on. Of course fill back in. And used plumbers straps to secure to the top of the eve with antenna clamped on top. Never had a issue. Plan on putting that back in service here soon.
Growing up in the 60's, that is what everyone had.
I installed my own tower Tyler,it a 50ft.Unarco-Rohn,comm.grade tower.
I'm also using a Telex Ham-4 heavy-duty rotor system.
I set this up myself more then 30 years ago.(the tower and rotor,the antenna and coax is only about 3 years old)
I am getting ready to do the same think. I bought a 5” thick walled thirty foot aluminum irrigation pipe. I am going to have two square tubing uprights welded to plate metal so that I can pin the pipe in the middle and using counter weigh inside the pipe at the bottom. Then I will have a pin plate at the bottom so one person can lay the tower down when needed. Rotors nowadays go bad quickly and high winds can damage an antenna.
We put up,a free standing Rhône HDBX 80 for out arrrg station our selves 8 yards of concrete welded together the rebar to the stubs and built a gin pole yes you can DIY a tower just plan and have plenty f help !
I appreciate your expression of safety concerns just as much as I appreciate your knowledgable, easy-to-grasp recommendations and instructions. By the way, you look great in that super short haircut.
Thank you for your videos. I finally installed a new Clearstream 2Max on the roof. Picture quality is as good as the streaming channels I pay for. I appreciate all the info you provided. Can't believe how much better the quality is with an outside antenna. Thanks again.
I'm glad my videos helped you get better reception. Feel free to give a contribution at the link below as I spend A LOT of time making the videos and responding to these comments:
antennamanpa.com/support.html
Great video brother. Keep up the good work!!!
Disclaimer: Please don't death yourself installing an antenna! Hire Tyler to comically fall of your roof, he's insured!
Everything he says applies to mounting VHF/UHF ham antennas too! I really like the Channelmaster J pole which could do double duty for me. I could put a 2M/70m on it and connect one end of my HF wire to it. The chimney mount is also one I didn't even think of. Thanks!
1:00
No people were harmed in the making of this video.
But many people were harmed installing antennas !
I used an existing j pole on the side trim. It had been installed by the direct tv guys. The install pulled the trim out from under the flashing after a few years and water got in. Rotted the facia and nearby sheathing. $2000 roof repair.
After removing an abandoned satellite dish from its support post I installed my antenna on the post. I connected the existing coax to the antenna and then crawled under the house to install a splitter in the existing coax. I ran two coax cables under the floor connecting them through holes in the floor to TVs. I’m 71. What does age have to do with ones ability? Know YOUR limits, be careful and forge on.
Truth and Quality.
Practical and Useful Information.
I agree , I am 70 and still going.
Some Humans have some strange ideas about being older.
Some one ask me if I am old and lonely , Yes I understand the question.
However for me the question strikes me as odd and humors.
I remember what my grandmother said years ago before see died , when my mother and grandmothers other kids were giving her that talk ,
Mom you need to slow down.
My grandmother told her kids , my mother being one of them.
She said , I can die anywhere , I am not going to stay home and wait for it.
Hey what a great idea to use that old satellite pole! Thanks!
How do you know if it’s grounded? Did you need hardware to install the antenna on the satellite dish post? Thx.
Saw a walmart ad on facebook today for a 960 mile 4k ultra HD antenna. LOL
I had really good results with an attic mount about 25 miles from the antenna farm in Phoenix, AZ
I am surprised you didn't mention the telescoping push-up pole before going to a tower. Growing up in the 70s, I lived out in the East Texas countryside, and the nearest stations were in Shreveport, LA, about 70 miles away. Everyone had a push-up pole at about 35 feet and these worked great. They don't require a concrete base like a tower, and I've seen them as tall as 50 feet. They do require guy wires, usually around the eaves of a house. We even had a rotator installed on one for a time. Easy to install DIY, you don't need a contractor for it. A really bad storm may bring one down, but they are inexpensive to replace.
I like tv towers much better.
Love the vids Tyler. You are the “Chris Fix” of TV antennas. Thank you
Thanks for another useful video. I used the "J" pole that came with my antenna. I do need to try to find another one that is longer, so that the elements will clear the edge of my high-pitched roof.
Amen on drilling into the roof. Nice shave!
Another great video! I see all these satellite dishes on people's roofs. I understand the possible issues. I'd like to kinda shield mine behind my chimney, but I have a gutter on my fascia, and I need to get the antenna far enough away from the chimney so it doesn't interfere. Anyway, great ideas here
In addition to possible leaks using a tripod, which I do use, you need to ensure you anchor the legs into the rafters. I originally used the tripod to mount an amateur radio vertical but "retired it in place" after removing the vertical rather than exposing the holes in the roof. When mounting the tripod to the roof, I used waterproofing compound in the holes, on the large mounting screws and under the mounting plates. I also covered the mounting plates with waterproofing as well. That tripod now has a second life holding up my large rotatable outside TV antenna.
Would I do it again? NO.
Great video. Thanks
I mounted my Channel Master CM3020 on a telescoping homemade pole. Bonded to a chain link fence pole in the ground. It is about the same as using an eve mount. It is slightly above the roof line. Signal is marginal to poor. Even with good RG-6, preamp, and good antenna. I need more height, I have a lot of trees in the way. I need a tower, But that cost a lot. Anyway, Good video man.
Nate Newman id like to see this telescoping mount you used . Could you send pics ?
WoW !
When your antenna pulls in Lightning,
I bet it will be an overloaded fire Hazard !
I have trees in the way as well. I'm about 10 feet above the peak of the roof and get good reception until the tree leaves get mature, then I lose half my channels.
Truth and Quality.
Practical and Useful Information.
A Tall Straight Pine Tree can be a Tower for a antenna.
The Type and Kind of Pine Tree that has a single trunk that goes straight up.
Up where the antenna is at , cut the branches away so will not whip around in the
wind and destroy the antenna.
One tip I can give on waterproofing the coaxial connectors do not use electrical tape it will loose it’s grip I did this on a large array with two antennas for picking up stations in two directions and a year later starting having problems found the end into house was wet from it wicking in from out side I replaced all the coax and new ends used the mastic that you see the commercial tradesmen on there connectors wrap every connector wet your fingers and mold it to the coax and around the splitter and lightning arrestor connections will seal things up well I also had the problem with our radio transmitters coax replaced it did the same thing no problems now four years .
Interesting, I was going to do a chimney mount this spring but after your caution if the chimney has a working fireplace I will need to rethink the mount.
Mount the antenna on a pole, with the chimney straps, that's eight or ten feet above the chimney. If that melts your antenna, you're using your fireplace wrong❗
I have a 32 FT tower and i'm putting up a cm 3020 is 10 FT X 1 1/2'" standard electrical conduit good to hold it. Thanks for the nice informative videos
I ran a 20’ pole from ground up & braced at peak of roof.
18” in cement below ground; 7’ above roof for antenna.
Seems to be strong enough for hurricanes here on gulf-coast,
as well as a good ground for lightning strikes.
Just FYI reference the concrete as it is not considered a ground connection ,separate grounding to mast be used. Lightning can easily blow the concrete foundation apart. Also, very very rare do TVs survive a direct lightning strike but proper grounding with a proper inline arrestor often protects against close hits.
Funny, when I went to cable and later the Interwebs, I still wanted to be able to get OTA channels, before HD, even though I also wanted to take down the outside antenna. So I put it in the attic! Sat the big old thing on the attic floor, pointing the same direction, and raised it up until I hit the rafters, and hung it there! What did I do when we got an HDTV? NOTHING! Basically the same frequencies, so same lengths. Works great for local channels, all about 25 miles away. I get all 5 stations, and all of the .1 .2 .3 channels, too.
Great video Tyler! Six different mounting methods to consider. Thank you!
OH CRAP, I used a tripod! LOL. I did seal the holes and the lag screws with roofing caulk and haven't seen any leaks in 3 years.
That’s all it takes to seal them black roofing tar paste works well too slop it on liberally .
@Antenna Man et al. Tyler, an in-use chimney, was only used to vent excess heat to the outside via the terracotta flue pipe inside the chimney, and this was for a fuel oil furnace heating system.
Well, about 2 or 3 years after instaling the chimney mount system with an appriate sized antenna, I noticed some mortar joints and I believe some chimney bricks started cracking --- and this was my chimney; therefore, I do not recommended the use of chimney mount systems.
Tyler, I would challenge you to go back to one of your customers, of which you installed a chimney mount system about 3 years ago, inspect the chimney for cracked mortar joints and bricks to see if you notice any cracks in either and then let us know of your findings.Thanks.
I've serviced chimney mounts that were up there for a good twenty years with no issues. Sounds like your chimney issue was preexisting
I’m going to install mine on the arm of my old direct tv dish,.
How about a tripod secured with heavy sandbags for using at apartments with either balconies or patios?
in Minnesota I found the stack gas from the heating furnace attacked my chimney mounted antenna.
I plan to BUY that, But I have to figure a way to raise the 30' Pole with the Antenna on top.
Hi there Antenna Man, can you do a show on antennas for the FM radio? Thanks
FM frequencies use the twenty megahertz just above TV channel six. Any "Rabbit Ears" with adjustable length "ears" works great. If you're looking for a distant FM station, you'll need a outdoor antenna with good low VHF elements. Try the rabbit ears first. Good luck!
We put up 30ft mast and 3 sets of guy wires on the roof for long range tv here ; i have a 20 ft mast on roof with 2 sets of guy wires here in Sebastopol Victoria Australia
thanks for the video...it gave me ideas on how to mount my 2 meter ham radio antenna...i am a fairly new tech...thanks again
Power companies have a "Call before you Dig" phone number so that they can come out and mark the underground lines so that you can avoid them if you are digging or trenching.
If you call this same number they will also do an "Aerial Locate" so that you can avoid overhead power lines as well.
Just put a paper clip on the coaxial port and watch all the tv you can. Simple and quite effective.
Do I have to hoop up cables from the outdoor antenna to the TV? or placing the outdoor antenna is enough? please help me
I have an attic antenna, luckily the gable end points toward most stations (40-50 miles)so there’s no shingles or metal roof to block the signal, just a little vinyl and sheeting. When the weather is strange I can pick up two channels that are 135 miles away some funky way or another. They break up bad though so they can’t really be watched but they are there.
Truth and Quality.
Practical and Useful Information.
Yes the internet has , DX Reception Sites.
DX is a old term , Distance and X for unknown.
Information about reception , all manner of situations.
If the antenna is mounted high (attached to the chimney, for instance) how is the coax cable routed? To prevent roof leaks, I assume it doesn't enter the house from the roof. Is the cable laid down the surface of the roof and enters the house from a wall or soffit?
The cable usually runs down the side of your house then connected to the main coaxial junction usually in a basement, garage, or in a box outside your house.
Hey Antenna Man, how about some videos of actual antenna installations (attic or roof) showing the complete process and setup? That would be helpful. Thanks
Can't do it due to liability issues. Already had two lawsuits threatened against me. Don't want more....
@AntennaMan Tyler when you said you had 2 lawsuits threatened against you is it because you video taped yourself doing an installation? Or was it for something else. I can't see why you would be threatened with legal action if you were video taping yourself. There are other yt videos showing installs of TV antennas maybe I might have missed something.
My antenna doesn't use any of the mounts you discussed. It has a pole buried in the ground about one foot from the house. A bracket is attached to the pole and the house at the front of the roof fascia for stability.
that's my set up, but I used two top rails from a chain link fence.
We are within 13 miles of all wanted stations, and are mostly Line of Site. Our problem is the stands of 70-foot Douglas Fir trees that are between us and the broadcast antennas. There is no way to get above them, though there may be peekaboo slots between them that are clear some of the time. Any hope or suggestions?
We had one down the road that interfered with our arrrg radio stations STL sneak over drill into it pump round up into the hole in about 30 days it was dead !
Can you replace the antenna that comes with the Tablo 4th Gen, with an external one?
I paid a local installer $300 to install a TV antenna. They did what I think is a terrible job. Because the installer didn't bring a big enough ladder he mounted the antenna about 3' below the peak of the roof, on the side of the house, mounted exactly opposite my neighbor's satellite dish. I live on a butte about 8 miles from the main antennas used in the area. It would be line of sight except the peak of the house across the street blocks it by 2'. That side of the street is about a foot lower. I get ok reception and usually get about 65 channels, however a lot of them lose signal frequently, even main channels with strong signals. Oddly enough I have an old HDHomeRun 2 tuner box attached to a tiny Mediasonic 6" flat antenna. I get the best reception with it mounted 3' off the ground on inside of my front door, which is recessed from the front of the building by 6' or so, and it's pointed about 45* off axis from the towers. IT basically acts as a tunnel. The strange thing is, I get more channels than with the roof antenna, I lose picture much less often too. It's weird. Anyone have a guess as to what is going on?
I'm waiting and hoping that when ATSC 3.0 hits town that I'll be able to use an indoor antenna as it gives me many more options on where I can place my TV. Where they installed the antenna outlet is probably the worst place as any TV placed against that wall is reflecting 4 windows and a sliding glass door, whereas on the opposite wall there's no windows to reflect, and it's an outside wall.
Questions, my house is stucco, which means there's a wire mesh covering the exterior of every wall. It makes it hard to get a signal through doesn't it? Also, the windows are double paned and I think they might use some sort of metal vapor on the glass surface that also might block signal. I've tried any number of antennas with that window, that should be able to easily pick up stations but there are houses across the street that block it and only get 1-2 stations. Any opinions on how to get better signal? I don't want to drill through the wall to pass a antenna lead.
You will be waiting a long time, if ever, for ATSC 3.0. Call the guy back to fix the problem or go to small claims court.
Added 5 1/2 foot extension pole to existing 10 foot antenna pole and cleaned up all pixelation issues get around 50 channels around 40 to 50 miles now .thanks for the advise
Interesting. 90% of the Yagi style on roofs before the '80's were tripod type. Good video.
Nice hair cut! Good info on the external antenna. Thanks.
hi bro
I surprised you didn't talk about a roof pipe mount. If you keep the antenna low OR use guide wires for anything high, this has worked very well for me.
Is the transmiter that will connect to an antenna and put receiver at the TV locations. Bacic it would be coax less.
I am in a moble home with very little crawl space to get under it.
If signal is towards the south do I put the long prongs towards signal or smaller
Another helpful video 👍
Thanks Tyler ‼️
Second question: all but one of the stations at
No you shouldn't need a rotor
Thanks for the recommendation. I have subscribed to your channel and donated to you as well. May I ask: with stations 12 miles away but with tree stands in between, does antenna size or shape matter much? @@AntennaMan
@@melitgreybeardivey7436 At only 12 miles, most likely no problem at all. Just do the normal things; good quality RG6 cable with the shortest possible run. Tim, WA5MD Ham Radio
Nice video. Thanks for the ideas.
Hey EveryBody..
Please Please Please !!
If you are doing the mounting the antenna on your own.
Stay far away from Power lines..
If you chose to use a tower
( though perhaps the Best ootion..so Too it is the Hardest and Most involved ) Hire a Professional .
I prefer when Posible to use a Chimney mounts.
I Always use a Heavy Duty chimney mount
( usually ining 2 sets of chimney mounts .. since I prefer to use 3 or 4 chimney straps to Best and Securely mount the chimney mount ) of course I only mount antennas to Solid Heavy duty chimneys and do so in using a 10 foot pole to use with the chimney mount So that I can be sure to use 3 or 4 Heavy Chimney mount straps..
Using the other methods of antenna mounting is ok
However do Not lend themselves to a Extra heavy duty mount and thus Only should be considered with smaller antennas
Again be careful..beware of Electric lines and or Hire a Pro !!
MrBOB39 I agree. I wanted to use my old satellite pole, but it is near power lines. I will most likely use one of the other mounts suggested.
We put up a Rhône HDBX 80 for out arrrg radio station the base was 8 yards of concrete with rebar placed as per there engineers plans we got with it I welded it all together on the stubs the tower bolts to I also built a gin pole that clamped to the tower sections took 4 of us a half day to erect it and instal the antenna lightning rod nav light and all the cabling to the light and antenna it’s a free standing tower as installed it’s rated for a 90 mile a hour wind constant with a build up of 3/4 inch of ice on it we put two ground rods 4 feet apart 8 feet into the ground used number 1 copper wire and burndi clamp from top on the rod to both ground rods cost was high but it’s well grounded has taken multiple hits with no damage to any of the lighting or equipment up on it Yes you can DIY a tower !
I'd like to see you make a video on using the existing Dish Network mount if possible.
grounding the antenna is the most important procedure.
If there's already an old tower installed, is there a way to update it or get it to work?
Channel master adjustable eave mount arrived without instructions! Instructions they emailed were vague at best, a pic from your video helped a little but, can’t believe there are no videos of anyone installing the eave mount brackets. Maybe you could do an antenna installation video
Roof penetrations are out of the question. Looks like i'll be biting the bullet and buying the chimney strap
What about using an existing roof top satellite dish mount and retrofitting it?
LoL the 7 way work fine the problem there a right way and wrong way to install them you need mount 2x6 under roof so that lug bolt get a bite and roof sealer flex tape or spray and don't what install on an old roof and need check ever 3 year re-apply flex spray.
I am buying a mobile home and see that there is a satellite dish mounted on the carport, can this be useful in any way to get Ota stations... thanks
You can replace the satellite dish on the pole with an antenna but it has to be done a very specific way or you will mess up the signals. I offer setup guidance at the link below: antennamanpa.com/antenna-recommendations.html
Who can I hire to install a big metal antenna onto the roof and hook it up to my TV?
I live close to Gettysburg PA and cannot find anyone to work on my antenna.
In my house we have Comcast cable, but the cable only goes to one point in the house and is then distributed to the rest of the house via the Comcast boxes that are connected to the wifi network. I would like to cut the cord with Comcast, but not sure how I would get the signal to the other TVs. Is there an option to put up an outdoor antenna, bring the signal into the house via that one coax cable, connect it to a box and distribute the signal via wifi?
What about use the mount that come with Dish Network or Direct TV? They don't bother to come and take it off and some houses had it sitting there forever. You certainly can dismount them and then mount your antenna, right?
can we please do an video on Antenna AB switch please ... also shared RF signal issues example ct nyc market
One direction fox 61 NW another antenna SW pax 31 comes in
*** or an 8th way, akin to the tower...... Why not install a 4x4wood post in the ground & install antenna on it?
......I tested my Clearstream Max-V on a 6 ft ladder, & it got good reception at that height, so why not use a 6 or 8 ft post next to the home?
I’m Interested in serious reactions to this method before I go for it.
I didn’t want to drill into my new roof.....
I considered side mount (it comes with j bracket) but I have elec lines above, so I’d with have to install at that 8 ft height against side of home, or place a wood post
I have a hip roof, no chimney and want my antenna higher than a couple feet above my gutter line. Won't be putting in a tower. Looks like option 7 for me.
Save the tripod on the roof. Use a roof stand off and pole mount. Two top rails from a chain link fence that's 20 feet from the ground and sturdy, the stand off is mounted to the roof edge as shown in the video here. Don't forget to ground everything and if you are not close enough to your house power ground, put one in! It should be available from your local hardware box store usually 10' copper rod.
plenty of videos on installing an outdoor antenna but what about replacing the coaxial cable that is soldered onto the small pcb board from an indoor antenna? Most of these antennas use the old RG-6 or China's 3C-2V coax cable with about 10 feet of cable connected directly to the antenna. Getting the best reception on these antenna's by replacing the coax cable, with RG-6, would be helpful. After all not everyone can install an outdoor antenna depending on where and what they live in, aka Apartment complex. I currently have a QFX ANT-17 that has 3C-2V coax cable soldered to the BCB board. removing two screws gives access to the board.
Hey Tyler , I have a new antenna mohu , replaces a crap wire antenna that replaced an old Mohu antenna . IMO Mohu make a great antenna . My question is could this new mohu eaf ranger amplified be mounted to crap wire antenna ? I am 65 miles from most towers , I connected my wires to an old dish satellite connection , wire runs to my deck , up a pole that i secured to a deck post , This works for me , even the paper thin mohu i placed outside picks up channels . The new antenna has holes to secure . I am drawing a blank on how to secure this new antenna . Thank you . BTW your how to videos are full of informative info , very helpful , thanks !
Ty, didn't mean to pick on your hair cut last video. Just took me by surprise.
However, is it possible to extend the antenna pole to raise it higher, or does that affect stability too much?
You didn't mention using a swivel base for an antenna pole so you can raise and lower the antenna pole making it easy to set up an antenna.
I have a unique problem with my brick ranch home .I have no eaves on my roof..only several hips. Plus, I have 3 foot soffit overhangs all the way round my house, so my antenna pole needs to mount 3 feet from the outside of the wall, and go up just outside of my gutter, and up around maybe 10 ft to clear my roof peak. Any wall mount antenna mounts that are at least 38 inches away from my wall to secure my antenna pole? Any ideas would be appreciated.don’t really want to put on the roof.
Can I put a splitter on the RG6 cable so that I can run the cable to 2 different rooms?
Are motorized antennas useful or not necessary with today's digital antennas?
Good info, Keep up the good work & Thanks.
Something about chimney mounts: Chimneys might look solid and they might look like they can bear a lot of weight but it really is a bad idea to tax your masonry like that. For example my house had a masonry chimney with a large television antenna when I purchased my house in 2005. The chimney was detached already, but I'm pretty sure having the extra weight of the antenna didn't help and it slowly moved a little more each year. I had the chimney demolished and replaced with a box in 2019. The guy I hired to demolish and replace the chimney said that he had to man handle to keep the whole thing from falling down all at once after the flashing was removed
Curious why the standard option like Telescoping Antenna Masts was not mentioned. My question to these is guy wires are often recommended and I hate guy wires. I'm wondering it say a 40' telescoping mast but only extended to 30' would work w/o guys wires on a medium to light antenna. In other words, only partially extend each section hopefully increasing strength would skirt around the need for all those ugly guy wires.
I have a large metal sided out-building 100 feet from the house and it is between the group of broadcasting towers 30-35 miles away and my house. The metal building is 2xs taller than the 1 story house and the building is a lot bigger. Can I put the antenna on top of that building and have a 200 foot rg6 cable rub to the house? With a long rg6 cable I would probably need a amplifier? How long can you have a rg6 cable?
Tyler, any suggestion for a mounting adapter for installing the J mounts on the fascia of a house for smaller antennas? I hate to go buy the $50 universal J mount when the 19" J mount that comes with the antenna is fine in 90% of the cases. The problem is the mounting bracket is just too tall to fit on the fascia board especially with a drip edge installed. I'm still waiting on someone to create a rigid 1/8 metal plate that matches up and will work. Most of our homes here in Fl have shallower peaked roofs and the 2 piece eave mounts won't work well. So it's either using a wall mount standoff (overkill for a smaller yagi like the Ant751) or making a bracket out of PT 2x8 to install for each home, which gets a bit old and not as slick as I'd like.
Can you make a video on building a freestanding mast without needing guy wires and mounting it?
Good video Tyler, you gave some solid information here. It can be a difficult subject with all the varied antennas and mounting options. Pay attention people.
What's your opinion of the CM-3079 used as a Eve mount brace for a Channel Master 40ft telescoping mast anchored in the ground to a cemented base pole & 5 guy wires for the Top section.
A Good Well Thought Out Video All The Best To You.