Trick for getting the contraption in front of the window track when you’re putting everything back together: I used a long dandelion digger (I have one but I don’t dig up those beautiful dandelions). But a long strong screwdriver would have worked too. I put it into that key shaped screw hole and used it to lever the window track over. The contraption slid right in. The key shaped hole that I’m talking about is the uppermost one that is inside that Hans said you really didn’t have to take that screw out because it’ll fit through the wide part of that key shaped screw hole. You can see this key shaped screw hole at 20:38 Hans is putting that upper screw into it. A word of caution, I did not take that upper screw out in the beginning because it fit through the wide end of the key shaped hole. But when I put everything back together that screw bent the lower edge of the key shaped hole because I had too much of a strain on it. So I had to use a hammer to gently bang the edge back to normal. Also, that glued on rubber guard that goes over the two upper screws on the outside back of the door was almost completely off on my door and it was hanging down so I think it was probably interfering with the latch. I left it off. May have been the problem all along, but the mechanisms inside the contraption were gunky and sluggish anyway. Thanks a million, Hans, for an excellent video; I followed it step by step and my door is completely fixed and working again. No unlatching 2 seconds after latching and no door alarm while driving. I am very glad you showed how to put everything back together also! Thank you!
@@hanspoole thank you again. Next project for this old Grammy is …. the washing machine… I replaced the cogs but I think another little thingy needs replacing too!
No joke! Was dealing with a constant dead battery about the same time one of the rear doors stopped working, stumbled upon your video, did exactly what you did, and wah lah! The rear door is working perfectly and no more battery drain! You're awesome keep up the good work!
Found the needle I needed in the hay stack. Thanks to Google long tail keywords and the creation of your VERY thorough video, my battery is not draining anymore and my door actually works now. It didn’t just fix the latching, but my entire system. I appreciate you creating this! Thanks again.
Great information. I have been trying to figure out why my door was not working and my battery was dead every morning for days now. I thought the door motor was dead. Your fix worked for me and saved me a big bill at the dealer. Thank you.
What a money and time saving video this is! I literally sat in my van with your video pulled up and walked through every step with you. My door now works perfectly. Thank you for your effort.
I never leave comments but you sir have saved me a bunch of money that I do not have at this time. It was driving me crazy. I was afraid to attempt it at first but with your video I had no problems. Very detailed. Thank you thank you thank you.
Thank you for this video. I cleaned out the OEM motor and it worked for a little bit but failed again. I gave up so I ordered a new motor assembly as well as door latch actuator and my door is good as new now. Thanks so much!! This video saved me hundreds of dollars in repair costs and also has prolonged the life of my 18 year old minivan which is very hard for me to part with. Only 169K miles and still running strong!
This video was very useful!! It shows exactly how to fix the issue. One thing I would recommend is using a rag rather than the pick for the very first step, taking the door handle off the panel. There is a different video showing how to do it. Everything else is top notch!
@@hanspoole I meant to say rag. Slide a rag at the back of the handle, pull down and to a side and the clip should come off. Make sure you don't loose it. 😉
Initially looking for a video that addresses the door closing issue and not realizing that that was also the cause of my battery draw that I am experiencing also. Thanks for the video, nice job!
Fantastic job showing exactly how to... step by step. Nice filming job, superbly edited too. Simply the best how-to car fix I've ever seen!! Hats off to you from a guy who has been doing this for 45 years...
Thank you a MILLION times for posting this video! It was incredibly helpful. I had the same problem on my 2005 Odyssey EX and while I didn't undertake this entire process, it helped me understand and ultimately fix my issue. I opted (for now, at least) to remove the 3 screws one at a time and spray WD-40 into the holes in order to try and lubricate and clean whatever mechanisms inside were gunked up, as recommended by on of the commenters in this thread. I also cleaned and lubricated the latches / moving / closing mechanisms at both the front and back sides of the door. I will try to update my comment in a few months regardless if this is a permanent or temporary fix. I only need my Odyssey to last another year or two at the most, and we no longer chauffeur our kids or other people around in the car too often, so I am hoping this can stay fixed for the near term. If not, I'll be back to this video for more guidance on how to remove the door panel and get this thing cleaned and lubricated properly.
Hello. I unscrewed the screws and squirted some spray white lithium grease in through the front and back holes. Because I am in no position to crawl in the back of my van and attempt what Hans Pool has done I tried your method. I’m in a wheelchair. So far so good. It’s closing and opening every time and I can’t detect any drain on the battery, parasitic draw or alarm going off. I still don’t trust it so I’m disconnecting the battery every night until I test it more. But if this works, I’ve just saved myself over $2000. I think I’ll put it on my phone calendar to lube it up that way every six months - pending final results. Thanks much for your suggestion!!!
Thank you so much for this video! We've had issues with our 2009 for a couple of years now. My wife and I were able to fix it thanks to this video. It was hard to get the unit back in the door but we managed it somehow.
I'm glad you were finally able to get it fixed! I completely agree that getting the latch back in place is the hardest part, but it sure is satisfying when it eventually goes in.
Wow impressed! Totally worked! 2006 Honda Odyssey. Had a battery drain in a couple hours would be dead, sliding door stopped working automatically. Now not draining battery at all and sliding door motor working after cleaning and lubing as instructed in video. Took it to two mechanics, one gave up and the other said it was the micu computer for $1500, going to share this vid with them. I never leave comments. Thank you so much!
A great and every helpful video, Hans, thank you very much. My neighbour had the identical problem, and after a failed attempt by a real mechanic, I managed to fix it for him for a good price and help us both out. Your filming and lighting is excellent, and your thorough explanation without wasting time or words is great.
Thanks for the video. I wasn’t having battery drain but the door wouldn’t “know” it was latched and the warning beep would come on when I put it in drive and stay beeping throughout the whole trip. It would be like this for hours or sometimes days. Now that I know where the problem is likely to lie, I’m going to tear it apart! Much appreciation!
Thanks for the thorough video and for following up on the comments. Followed the video step by step, took about 2 hours, jump started the van and drove around 45 minutes. Tomorrow morning we will find out if it worked! Thanks again
@@hanspoole so the van started up this morning and the annoying audible alarm for an open sliding door is not making any noise so I think my problem is solved. Thanks you saved me a bunch of money and time, do you have Venmo?
Speculating that this problem is worse in the winter bc the lithium grease in the latch mechanism gets stiff. Seems to be a pretty common problem looking at the Odyssey forums
Thats exactly my problem, thank you for the details. Interesting mention of yours was about stopping the doors from closing automatically while working on this problem by switching off the auto door operation, by switching it off on the dash. That got me to thinking,… wonder of i switched to off,… if the drain would go away, just for testing purposes….. “ It did stop the drain “ on my problem. If I switched it back on and cycle the doors… open and closed again the drain came back and would not go away. This simple test verified that the door latch switched is my problem. I can leave the doors in manual mode till i have time to do exactly what you did in the awesome video.
Thanks to you I've finally fixed the problem I had with my van. Spent 2 MN winters turning off my battery every night with a twist switch, not knowing where this drain was coming from. I always suspected the doors but couldn't be 100% sure and couldn't spare the expense. Very nice video, easy to follow along!
So your door wasn't beeping at you and the battery was draining? Ppl are saying their door alarm was beeping but mine isn't and my battery is draining overnight
@@Miamijunglist Mines the same way. No beeps or warnings but one time I turned and the passenger door literally slid open. My battery is fine if I drive every day but 2 or more days leaves it dead. I've just been using my portable jumper every time but figured now that it's warmer I need to fix it. I suspected the doors were the problem. I am going to test the fuse etc before tearing into it.
Well done! If you measure the parasitic draw before the repair, it is about 370 mA - 400mA. After the repair it will be around 20 mA. That upper screw in the "key hole" slot is meant to be loosened until it gets hard to turn but left in the latch. Then during removal it does fit through the hole. The reason you had to use the ratchet all of the way out is because of the interference threads that keep the bolt from falling out during shipping/assembly. Also the bolt you reinstalled in the "key hole" slot should go at the bottom. The flat washer on the bolt for the window run channel lower bracket is because the hole is slotted, so the washer adds support when bridging the slot. All in all, a great DIY video.
A couple of questions. Mine has the 380 mA draw. Does this still happen even though door open indicator does not come on? Does the parasitic draw still happen even though you turn off the switch on the dash so the power doors don’t work? I pulled the fuse and still have the draw. Could it still be the same problem? Basically, how can I be sure this is the problem before I tear the door apart? Thanjs
@@bobh6728 I am in the process of also repairing this problem. The light on the dashboard does not tell me that a door is open. But if you close the door manually you will notice that the door at the back does not get pulled in tightly to the frame of the doorway. You can actually unplug the doors from working automatically at the rear right-hand side of the van, . But you need to pull the plastic side panel off enough so that you can reach the plugs. I think it's called the rear MICA. This is the area where the heater blower is located. While I agree with absolutely everything in the video I will add that there is at least one electronic component that if bad will also keep your door from working properly. If you look in the video you will see one or two of them and they are green in color. I think they are called an actuator switch? I purchased new ones from an online electronics company and they were only about $7 each. Might as well replace them if you're going to do all that work anyway. My 2 cents.
Appreciate the clear description of this repair process. Without the tip on removing the window rail bracket to reinstall the latch, I don’t think I would have finished the job. I recommend testing the door before reinstalling the interior panel and trim.
That one little step saved me a lot of struggle and wasted time as well, and that's why I chose to show it in the video. Great tip about testing it out before reinstalling the trim panel! That could potentially save someone a lot of frustration if they had forgotten to connect a cable or switch!
If anyone is having this problem . I just fixed mine easily… I did exactly what the video showed.. still had the drain.. come To find out the the other door had the same issue!! I opened both doors and sprayed a generous amount of wd-40 inside the rear door latch on both sides - closed and opened the doors a few times - and the problem is now solved!! Good luck and thanks for this video
Thank you so much for taking the time to make this video. This was the most ambitious DIY car repair ive done and there is no way i do it without your help. You saved me a bunch of money. Wahoowa!
After watching this, I knew this was my problem from the intro, when the door closes then bumps a little bit open. It's getting towed to the shop tomorrow, then I will see what they say. Thank you for the info!
Thank you for this! Best video I've seen on this repair, by far. It's not too long at all. Showing every step is key IMO, and watching it gives us a mental run-through of how it's going to go. Going to attempt this soon. Very well done, thanks again!
I had this same issue and it only happened in the winter. I replaced the mechanism instead of cleaning/lubricating, but a very thorough and helpful video.
Thanks for the video. I've been looking on how to repair this exact thing for about a month now. Part is incredibly expensive so i needed i cost effective way to repair. Again thank you
I have this problem in my 05 EX-L with 202k miles. I pull the fuse for the doors at night to avoid the battery dying...but I am so happy you made the video of how to fix the doors! Thank you so much! I'm going to work on mine this weekend. Unfortunately I also need center rollers on the opposite side, so I have my work cut out for me!
Third time watching one of these videos. I was originally searching for why I could not open the door at all. At 11:40 you explained my problem. Excellent thank you for the thorough and detailed explanation 👍 👍 👍 now I know what the problem is 😎
You are right about having to use oil or lithium grease. I did this to my doors a few years ago, but only used WD40 silicone spray and the problem came back. Now I have to do it again, so your video is super helpful. By the way, those hooks up top do come off, but they slide up and then pop out…I know because I broke mine and bought new ones.
Easy way to lube the inside of those puppies is to remove just one of the three latch mount bolts on the back outside of the door stick your lithium grease straw through the hole and spray inside. Replace that bolt and move onto the next bolt repeating the same step until you've done all three bolt holes. DO NOT REMOVE all three at the same time. One at a time and replace each one individually. This worked perfectly and saved a ton of unnecessary work and. anguish.
As you suggested, I also opted (for now, at least) to remove the 3 screws one at a time and spray WD-40 into the holes in order to try and lubricate and clean whatever mechanisms inside were gunked up. I also cleaned and WD-40 lubricated the latches / moving / closing mechanisms at both the front and back sides of the door. I will try to update my comment in a few months indicating if this is a permanent or temporary fix. (I suppose based on other comments, I may need to go back and use a spray lithium grease instead of just the WD-40.)
Interesting I just happened to buy Lithium grease spray can at Walmart today for like 6 bucks. I will try the 1 bolt at a time now instead of taking it apart just to see if it works. First I'm going to hook a multi meter up to confirm the issue
This is a great video you did a really good job! I found the micro switches online for only $7 each so I'm going to be repairing my doors and I will replace the switches anyway since my van is 18 years old with 340,000 miles! I prefer not to go through all that work and then not have my doors operate lol 😆 thank you again!
Some notes: Do not remove the upper trim on a cold day; the trim plastic will be more brittle and can break when pulling out the plastic trim pegs. My door handle did not have the metal circlip attached. I spent some time groping around for it before determining it was absent, and could just pull out the handle. The inner door handle has three cables attached to it. If any one of these hangs up, the door will have problems closing. Since you have the panel off, you should squirt some lubricant into the front latch assembly. It was sort of tricky to do this, but I could bend the squirt straw through a hole in the sheetmetal and guide it in with my other hand reaching into the door. This helped free up the inner door handle cables. I bought a used rear latch assembly for $100 off ebay. The little hinges and whatnot moved ok on the old one, after cleaning and oiling, but the plastic around the latch was shredded to bits. Also, one step I had to do once I got the new one in was jump the closer motor to pull the door shut for the first time after reassembly. I don't know if the computer thought it was open, or what. No amount of prescribed resetting hacks (pulling fuses, disconnecting battery, etc) worked. I clamped alligator clips to the pins inside the socket he's detaching at 7:45 and ran the motor off a little 12 V charger.
Thank you, after 17 years, i didn't realize how gunked and dusty and dirty the insides were. It didn't really help that when i started noticing the problem i was putting a lot of lube in through the latch because that was the way i usually fixed the issue, not realizing there was much more inside that was causing the issue. I spent a good 2 hours trying to figure this out and cleaning but i guess you saved me a couple of hundred. mine is still not nearly as clean as your and i have a feeling another cleaning will be necessary at some point but once done once, I think it's going be pretty easy.
I’m glad my video was helpful for you! I completely agree that after you do it once, the next time is much easier. The first door I did was a learning experience, which is why I filmed myself doing the second one😆
Thanks for the video, Hans. This is exactly the problem I am having so I will give this a try. Your video is nice and detailed, so I feel like I can tackle the job.
Yep, this is the video everybody with this fantastic Honda junker needs to see. Please become a manufacturing engineer, my dear friend. My tip: I put cargo springs in the back because of the sagging over the years, and it feels much better than stock.
@@hanspoole Yes, I was a little worried that the women might complain that the back of the van was too harsh, but it's fine. Feels real good, and it's not hard at all to do.
i actually extend out fuse 7 back up out to a switch and literally turn it off after locking the door then prevent the drain after extensive dig into where the drain is
All the symptoms look to be the same with mine as well (2006). Dead battery in the morning, doors that dont seem to fully latch. Hoping this repair will solve my problems. Thanks for the very detailed video. I'll try to repair it sometime this next week and give a simple update on how it went.
Update: I did this repair to both of my sliding doors and It totally fixed the problem of my battery being dead every 12-20 hours. I measured the current draw before the repair and it was 400mA and after the repair it dropped to about 30mA. It took me about 2-3 hours for the first door and just over an hour for the second door. Thanks for the detailed video!!!
@@jackjunk5495 Yeah pulling the 7.5amp fuse labeled "7 - BackUp" will also drop the battery amps from 400mA down to like 20mA. A quick fix for a battery draining until you can do the repair. I drove around for a week or so pulling the fuse everytime I parked it. Until I got around to fixing it using this video as a guide. That number 7 backup fuse also services the navigation system, door lights, power locks, dash lights when van is not running. and a few other things.
Very informative video! I have a 2004 odyssey and my side doors on both sides are messed up. Drivers side is really the culprit, so I will try my hand at this. Right now the drivers side back door won't even open so I have that to address too. Good video!
Thank you! Hopefully you’re able to get it all fixed up without too much trouble. The doors on my van quit working again last month, but it turns out that the micro switches are bad, so I won’t be able to get away with just relubing the mechanism. I’ll make a new video on my adventures once I find the time to actually do it within the next couple of weeks🤣
My situation was coupled with the symptom of a ticking/clicking noise only audible when near the fuse box. It was a pretty fast tick and didn't seem like it was gonna stop anytime soon even with the key out! I could literally feel the tick coming from the 7.5a fuse before i knew it was the one, pulling stopped the ticking! That's what lead me here lol The ticking has stopped and the door has no trouble closing anymore! I did not take the door apart as you did, I used WD to clean that wire/cord and the grooves and loaded them up with a buttload of Lucas Marine grease (i chose this grease for weather protection and its high melting point, apparently the kind doesn't matter as much) I also slapped on a silly amount of the marine grease into both latches at the front and back of both power doors. I did the trunk for good measure, wasn't having a problem there but hopefully I won't either. This worked good enough for me, literally no disassembly, i only wish I used a can of brake cleaner/contact cleaner with the long red tip to blow out the latches, there was dirt actually packed into that latch. I cringe looking back not doing it but I did it at break time at work lol (that's when i found my car died)
THANKS . MY 2005 rear sliding door wont open when the key is inserted into the ignition switch. I get a sliding door warning light but After I remove the key from the ignition switch, then remove and reinsert the 7.5A fuse; the rear door works great. IT system acts like a short somewhere when the key is inserted into the ignition switch. I will try cleaning the door latch like you suggested.
Took my '05 Odyssey into the shop today thinking I had an alternator issue. They called me back a couple hours later and said that my battery and my alternator are good and that they picked up on a parasitic draw, likely for the back doors, so they removed Fuse 7 from the driver's side fuse box and the parasitic draw went away. I know exactly which door it is too thankfully. It's the passenger side back door. We had opened it one day to get stuff out and then went to put the van in gear and it gave that buzzer sound as if the door was open. Opened and closed it a few different times to resolve the issue and it worked. However, the last time we had folks in the back of the van and it made the buzzer sound when we put it in gear, we just turned the power doors off so we wouldn't hear the buzzer. Now we know that we have to make sure the door gets all the way in so it doesn't drain everything instead of just turning off the power doors and calling it a day. One downside about running around without that Fuse 7 is that now the interior auto lights don't come on when the door is open, I can't use the FOB to lock/unlock the vehicle, and the power locks don't function without the vehicle being turned on. The guy at the shop said that he wouldn't be able to fix the issue and that I would have to take it to a Honda dealership. I'm not skilled with vehicle repairs or anything, I'm more of an electronics (computers/phones/etc) guy, nor do I have the space to work on it myself, so I'll either see if I can find someone to replace that latch or see if getting the latch cleaned out will help prevent the parasitic draw.
Yup, that sounds exactly like what I experienced before cleaning up the latches. We got pretty use to shutting off the door switch every time we put the van in gear🤣. I'm surprised you're able to get the door to close fully by just giving it a few tries. My guess is that it's just barely gunked up enough for it to not work sometimes, but not so much that it never works. Good luck getting it fixed!
Thank you for this video! Well made! The comments are helpful. I think there's a good chance my van has a similar problem, and I'm hoping it has an easy fix. We have a 2021 Honda Odyssey EX-L, which has had a parasitic drain since we bought it used 5 months ago. We just replaced the battery 2 days ago, but it still drains overnight. The driver's side sliding door won't lock with either the remote or driver door controls. A door ajar switch was replaced right before we bought it based on the Carfax report. The fuel door won’t open by pressing on it, and we need to use the emergency pull cable from the back hatch to open it. It has a DVD player that was added in 2021 but not from factory. At first we thought this might be the cause of the drain, but after watching your video we are wondering if the sliding door might be causing the drain and fuel door problem. We're wondering if we should try what you are showing in the video with the sliding door, or if there's an easier fix by pulling a fuse to the door like mentioned in another comment. Not sure how different these issues would be in a 2021 compared to the van in your video. Any other ideas are welcome.
I don’t need the door to open & close, I just need the battery drain to stop. What fuse(s) can I remove to break the power connection and stop the drain?
@@hanspoole Very thorough video and follow up comments! I was on the verge of installing an in-cabin battery disconnect switch in my 2007 Odyssey, but your video gives me new hope to address a root cause! Thank you.
Hello Hans. Thank you for this YouTu be video. I was able to successfully get my power sliding door operating again on my 07 odyssey. However, now the problem is the window won’t come back up now that I have put it down. I wondered if any of your other viewers have had a similar issue and if so, do you know how they corrected it? The next thing I’m going to do is check all the fuses to see if that is the problem. Again, thanks for the video. I’ll find out in a couple of days whether it fixed the drain on the battery.
Thanks for your response . After inspecting the switch on the door, I found the harness the switch plugs into wasn’t making full Contact . I was able to use electrical tape to hold things in place and the window gos up and down now. 😀 not sure how long this will last but the window is up for now. I may need a more permanent fix but this is good for now.
Thanks so much for making this! I’ve been dealing with this issue for a while now. I took my van to my mechanic, but we still haven’t been able to fully solve the problem. The best solution we’ve come up with so far is bypassing the electric doors, locks and interior lights to stop the parasitic drain, but that’s not ideal. I’d love to have everything functioning properly, including using the key fob to lock the doors. I’m excited to try your method this weekend and see if it finally solves my issue. Everything you describe here, and in your other video, matches what I’ve been experiencing perfectly. Do you have any tips on how to clean the tracks, and what product do you recommend for relubricating them after?
I've cleaned the tracks maybe one or two times (should probably do it more often) and from what I can remember, it's a lot easier if you remove that little trim piece that goes over the track. If you watch any video on how to replace the door rollers, it will be one of the first steps they show. I'd recommend using a white lithium spray grease.
Thank you for the amazing video. When I got my piece out of the door, I could not exactly tell what was wrong, if anything. I took the screw out that holds the little blue switch in place and tested the switch with a continuity tester - all was good (I was afraid this was the problem and I'd never be able to get just that switch). I also took the screw out of the switch so that I could push the switch aside or cover it while I sprayed some brake cleaner around that immediate area. I did this because I had white lithium grease on the door latch mechanism but regular amber grease everywhere else (window regulator). I felt it was better to leave the window section with its amber grease as is. The grease looked like it was doing it's job, but I really wanted to get all of the lithium grease off everything around the door latch area. With all of the lithium grease removed I could see everything working better. And by better I mean the slightest bit added to put enough pressure on the switch contact. The difference is very small to the eye but as you all know - that is what is needed, and you can verify this with a continuity tester. I then added some PB Blaster around the same area where the lithium grease was and cleaned off any that was running freely. Then I used your advice to use the 3 in 1 oil, but I wasn't exactly sure where the 3-in-1 was to be applied. I felt that the circular piece that rotates as the latch is activated and deactivated would be best served by some thicker oil there and I put a drop on the front side and back side. Hopefully that does the trick. Anyone else about to try to this job, I do think some brake cleaner gets the old crud out very well, just project the switch.
I discovered precisely the same thing when I took it apart for the first time. The mechanism seems to be moving ok at first glance, but upon further examination, you can see that the switches aren’t being activated fully. It’s the little things that count😉. Good point about using brake clean: while it works wonders removing grease, you’ve got to be careful around the delicate electronics.
my question is is the door open light on from this issue? he says ot thinks the door is open but mon dont show that on my dash unless i pop it open by hand
Thank the Lord above, you just saved me and my mother 1200 dollars plus on repairs for BOTH rear latches which were starting to go out, and the passenger side latch was even more locked up than the driver's side. I cannot thank you enough, and if you have a Ko-Fi, please give the link to it, because we would be happy to give you a donation as a thank-you.
I’m glad my video was so helpful for you! The satisfaction of knowing that my videos achieved my intended purpose is enough for me, and I am not familiar with Ko-Fi, so I respectfully decline your kind offer. Thank you for leaving a comment!
If you want to get rid of the parasitic drain and just have manual doors by pulling a fuse, then fuse #7 in the driver’s side panel is the way to go. However, by pulling that fuse you will also disable other features such as locking the doors with the key fob and dome lights automatically turning on with open doors.
I have the same exact problem and it’s very annoying while I’m driving and the map lights are coming on and off depending on when I turn right or left.🤦🏽♂️ I’m sure the price to have a professional fix this will run me a couple hundred, so thanks for the upload and information. I will attempt this myself and save myself some money. 💪🏽
@@hanspoole As an update, i tried the DIY method and failed. The passenger side sliding door still reads as if it’s open. My lights still come on. However, the light switch for the map light located on the dash behind the right side of the steering wheel, has an on and off and also an option to never have any lights come on when a door is open. I keep it that way now.
This was one of the best how-to videos I've seen. Very thorough, but didn't waste time with chattiness. Question: Is there a latch in the front of the door as well as the back? I am almost done putting mine back together, but....I noticed that the mechanism that seems to latch on the front...isn't free flowing and snapping back up like the other side. So, I wonder if that could also be an issue with the parasitic draw. Thanks again.
I’m looking into replacing the switch for the mechanism but I’m confused. Are there two switches in there and is one NO and the other NC? (Normally opened/closed)
Looks like people are looking at this video recently as well, so here it is. Prior to putting the latch back, put water proof butyl tape along the TOP seam of the latch to close off the latch from moisture coming down through the door. Door panel is not water proof and there is drain hole at the bottom of the door to let water out. However, the water gets into the latch (later version of the latch had couple of foam tapes which helps but not totally water proof) and eats away at the lubrication and also this is worse in the winter because the lubrication gets hard AND the moisture inside the latch will freeze making things worse. In my experience, doing what he does will get you through couple of seasons but the issue will come back and so far, I had to swap out both of my latches with new OEM one (about $250 each) but since I had to swap out batteries 3 times because of the drain, you will save $$ from not having to swap out the battery. In a pinch, I found spray and pray method works for a month or 2. Just undo the 3 bolts from the back of the latch one at a time and spray with plenty of brake cleaner/degreaser using long straw followed by lithium grease (suitable for low temp) followed by manual opening and closing of the door 10-15 times will usually get the door gears unstuck.
That is a very good caveat to take note of! In fact, the microswitches on both door latches went bad on our van a couple of months ago (the latch mechanism still moves freely) and I'll need to solder in some new latches. In my case, I think what happened is that a lot of condensation formed on the inside of the door due to drastic temperature fluctuations. Haven't gotten around to putting in those new switches yet because life has been too busy, but I'll make sure to make a video when I finally get around to it 🤣
Thanks for the video great advice.. would you happen to know how to kill the sound when door is not shut ?.. my door is shutting but sometimes it doesn't and it's making an annoying beep sound
There's a couple ways to do that, easiest is to just turn off the sliding door switch on the dashboard to the left of the steering wheel. You can also remove the legendary fuse #7 in the driver's side fuse panel, but that disables more than just the doors.
@@hanspoole yeah I usually turn it off to manually use it .. but I thought maybe there was a way just to turn off the sound itself without touching the fuse
My 07 odyssey has the same symptons. Drains the battery after a couple days if not driving it. Blend door actuators going bad, Door sliders also bad. Everything else will go bad all at once. Cars a junk after 15 years. They should make cars simple again. Thanks for the video lesson.
I have a 2004 Odyssey with the same parasitic drain on battery. The #7 fuse on driver side is labelled "IG coil", 7.5w. I found the power slide fuse in panel under the hood. It's shows 30amp. If I pulled this fuse could it stop the battery drain? Or can I flip the switch inside so auto slide is OFF? Thank you for the detailed video.
I'm too lazy to take the door apart and just sprayed the heck out of the visible portion of the latch mechanism with lubricant. I'm encouraging my family to just NOT USE the driver side sliding door. This problem gets worse in the winter. Edit: this actually worked all winter! Even using the door was totally fine. Definitely five my method a try before taking the door apart.
The clip is towards the front of the van on the black connector. Push the top of the clip toward the connector, really firmly, and it will release at the bottom. I used a flathead on the connector to push it upwards simultaneously.
Don’t need to do this…. Just remove the top two 10mm bolts on the lock latch. Spray cleaner inside and lubrication. This sprays direction into the gummy area. Replace bolts, run it a few times and you’re done. Great video tho
I was excited about finding this video so I took everything apart on my 07 and it looks like someone recently lubed everything and all the little mechanisms seem to be working fine. Any ideas on what to do from here? My van has all the symptoms you described at the beginning of the video
Trick for getting the contraption in front of the window track when you’re putting everything back together: I used a long dandelion digger (I have one but I don’t dig up those beautiful dandelions). But a long strong screwdriver would have worked too. I put it into that key shaped screw hole and used it to lever the window track over. The contraption slid right in. The key shaped hole that I’m talking about is the uppermost one that is inside that Hans said you really didn’t have to take that screw out because it’ll fit through the wide part of that key shaped screw hole. You can see this key shaped screw hole at 20:38 Hans is putting that upper screw into it. A word of caution, I did not take that upper screw out in the beginning because it fit through the wide end of the key shaped hole. But when I put everything back together that screw bent the lower edge of the key shaped hole because I had too much of a strain on it. So I had to use a hammer to gently bang the edge back to normal. Also, that glued on rubber guard that goes over the two upper screws on the outside back of the door was almost completely off on my door and it was hanging down so I think it was probably interfering with the latch. I left it off. May have been the problem all along, but the mechanisms inside the contraption were gunky and sluggish anyway. Thanks a million, Hans, for an excellent video; I followed it step by step and my door is completely fixed and working again. No unlatching 2 seconds after latching and no door alarm while driving. I am very glad you showed how to put everything back together also! Thank you!
@@hanspoole thank you again. Next project for this old Grammy is …. the washing machine… I replaced the cogs but I think another little thingy needs replacing too!
This is a better instructional video than 99% of the videos on the web. Great Job!
Wow, thanks! I’m glad it was helpful!
No joke! Was dealing with a constant dead battery about the same time one of the rear doors stopped working, stumbled upon your video, did exactly what you did, and wah lah! The rear door is working perfectly and no more battery drain! You're awesome keep up the good work!
Found the needle I needed in the hay stack. Thanks to Google long tail keywords and the creation of your VERY thorough video, my battery is not draining anymore and my door actually works now. It didn’t just fix the latching, but my entire system.
I appreciate you creating this!
Thanks again.
That’s precisely the reason I decided to make the video, so I’m glad to hear your experience!
Great information. I have been trying to figure out why my door was not working and my battery was dead every morning for days now. I thought the door motor was dead. Your fix worked for me and saved me a big bill at the dealer. Thank you.
What a money and time saving video this is!
I literally sat in my van with your video pulled up and walked through every step with you. My door now works perfectly. Thank you for your effort.
I never leave comments but you sir have saved me a bunch of money that I do not have at this time. It was driving me crazy. I was afraid to attempt it at first but with your video I had no problems. Very detailed. Thank you thank you thank you.
Thank you for this video. I cleaned out the OEM motor and it worked for a little bit but failed again. I gave up so I ordered a new motor assembly as well as door latch actuator and my door is good as new now. Thanks so much!! This video saved me hundreds of dollars in repair costs and also has prolonged the life of my 18 year old minivan which is very hard for me to part with. Only 169K miles and still running strong!
This video was very useful!! It shows exactly how to fix the issue. One thing I would recommend is using a rag rather than the pick for the very first step, taking the door handle off the panel. There is a different video showing how to do it. Everything else is top notch!
Good to know! I struggled to remove those clips with the pick method, so it's nice to know that there are more efficient methods out there.
@@hanspoole I meant to say rag. Slide a rag at the back of the handle, pull down and to a side and the clip should come off. Make sure you don't loose it. 😉
Ah, that makes more sense, I was kind of wondering what you meant with "tag" 🤣
Initially looking for a video that addresses the door closing issue and not realizing that that was also the cause of my battery draw that I am experiencing also. Thanks for the video, nice job!
Fantastic job showing exactly how to... step by step. Nice filming job, superbly edited too. Simply the best how-to car fix I've ever seen!! Hats off to you from a guy who has been doing this for 45 years...
This was the best video on the subject of parasitic drain and removing door panels and lubricating mechanism for this car great job ! 👏
Thank you a MILLION times for posting this video! It was incredibly helpful. I had the same problem on my 2005 Odyssey EX and while I didn't undertake this entire process, it helped me understand and ultimately fix my issue. I opted (for now, at least) to remove the 3 screws one at a time and spray WD-40 into the holes in order to try and lubricate and clean whatever mechanisms inside were gunked up, as recommended by on of the commenters in this thread. I also cleaned and lubricated the latches / moving / closing mechanisms at both the front and back sides of the door. I will try to update my comment in a few months regardless if this is a permanent or temporary fix. I only need my Odyssey to last another year or two at the most, and we no longer chauffeur our kids or other people around in the car too often, so I am hoping this can stay fixed for the near term. If not, I'll be back to this video for more guidance on how to remove the door panel and get this thing cleaned and lubricated properly.
Hello. I unscrewed the screws and squirted some spray white lithium grease in through the front and back holes. Because I am in no position to crawl in the back of my van and attempt what Hans Pool has done I tried your method. I’m in a wheelchair. So far so good. It’s closing and opening every time and I can’t detect any drain on the battery, parasitic draw or alarm going off. I still don’t trust it so I’m disconnecting the battery every night until I test it more. But if this works, I’ve just saved myself over $2000. I think I’ll put it on my phone calendar to lube it up that way every six months - pending final results. Thanks much for your suggestion!!!
@@wavoconqueso Hi, which screws holes you sprayed lubricant through
Thank you so much for this video! We've had issues with our 2009 for a couple of years now. My wife and I were able to fix it thanks to this video. It was hard to get the unit back in the door but we managed it somehow.
I'm glad you were finally able to get it fixed! I completely agree that getting the latch back in place is the hardest part, but it sure is satisfying when it eventually goes in.
Wow impressed! Totally worked! 2006 Honda Odyssey. Had a battery drain in a couple hours would be dead, sliding door stopped working automatically. Now not draining battery at all and sliding door motor working after cleaning and lubing as instructed in video. Took it to two mechanics, one gave up and the other said it was the micu computer for $1500, going to share this vid with them. I never leave comments. Thank you so much!
A great and every helpful video, Hans, thank you very much. My neighbour had the identical problem, and after a failed attempt by a real mechanic, I managed to fix it for him for a good price and help us both out. Your filming and lighting is excellent, and your thorough explanation without wasting time or words is great.
Thank you! I’m glad it was helpful!
Thanks for the video. I wasn’t having battery drain but the door wouldn’t “know” it was latched and the warning beep would come on when I put it in drive and stay beeping throughout the whole trip. It would be like this for hours or sometimes days. Now that I know where the problem is likely to lie, I’m going to tear it apart! Much appreciation!
Thanks for the thorough video and for following up on the comments. Followed the video step by step, took about 2 hours, jump started the van and drove around 45 minutes. Tomorrow morning we will find out if it worked! Thanks again
@@hanspoole so the van started up this morning and the annoying audible alarm for an open sliding door is not making any noise so I think my problem is solved. Thanks you saved me a bunch of money and time, do you have Venmo?
Speculating that this problem is worse in the winter bc the lithium grease in the latch mechanism gets stiff. Seems to be a pretty common problem looking at the Odyssey forums
Thats exactly my problem, thank you for the details.
Interesting mention of yours was about stopping the doors from closing automatically while working on this problem by switching off the auto door operation, by switching it off on the dash. That got me to thinking,… wonder of i switched to off,… if the drain would go away, just for testing purposes….. “ It did stop the drain “ on my problem. If I switched it back on and cycle the doors… open and closed again the drain came back and would not go away. This simple test verified that the door latch switched is my problem.
I can leave the doors in manual mode till i have time to do exactly what you did in the awesome video.
Thanks to you I've finally fixed the problem I had with my van. Spent 2 MN winters turning off my battery every night with a twist switch, not knowing where this drain was coming from. I always suspected the doors but couldn't be 100% sure and couldn't spare the expense. Very nice video, easy to follow along!
So your door wasn't beeping at you and the battery was draining? Ppl are saying their door alarm was beeping but mine isn't and my battery is draining overnight
@@Miamijunglist Mines the same way. No beeps or warnings but one time I turned and the passenger door literally slid open. My battery is fine if I drive every day but 2 or more days leaves it dead. I've just been using my portable jumper every time but figured now that it's warmer I need to fix it. I suspected the doors were the problem. I am going to test the fuse etc before tearing into it.
I found my drain, end up here. I was looking for this video 3 years ago😅. Amazing job young guy.
Well done! If you measure the parasitic draw before the repair, it is about 370 mA - 400mA. After the repair it will be around 20 mA. That upper screw in the "key hole" slot is meant to be loosened until it gets hard to turn but left in the latch. Then during removal it does fit through the hole. The reason you had to use the ratchet all of the way out is because of the interference threads that keep the bolt from falling out during shipping/assembly. Also the bolt you reinstalled in the "key hole" slot should go at the bottom. The flat washer on the bolt for the window run channel lower bracket is because the hole is slotted, so the washer adds support when bridging the slot. All in all, a great DIY video.
A couple of questions. Mine has the 380 mA draw.
Does this still happen even though door open indicator does not come on?
Does the parasitic draw still happen even though you turn off the switch on the dash so the power doors don’t work?
I pulled the fuse and still have the draw. Could it still be the same problem?
Basically, how can I be sure this is the problem before I tear the door apart?
Thanjs
@@bobh6728 I am in the process of also repairing this problem. The light on the dashboard does not tell me that a door is open. But if you close the door manually you will notice that the door at the back does not get pulled in tightly to the frame of the doorway. You can actually unplug the doors from working automatically at the rear right-hand side of the van, . But you need to pull the plastic side panel off enough so that you can reach the plugs. I think it's called the rear MICA. This is the area where the heater blower is located. While I agree with absolutely everything in the video I will add that there is at least one electronic component that if bad will also keep your door from working properly. If you look in the video you will see one or two of them and they are green in color. I think they are called an actuator switch? I purchased new ones from an online electronics company and they were only about $7 each. Might as well replace them if you're going to do all that work anyway. My 2 cents.
Appreciate the clear description of this repair process. Without the tip on removing the window rail bracket to reinstall the latch, I don’t think I would have finished the job. I recommend testing the door before reinstalling the interior panel and trim.
That one little step saved me a lot of struggle and wasted time as well, and that's why I chose to show it in the video. Great tip about testing it out before reinstalling the trim panel! That could potentially save someone a lot of frustration if they had forgotten to connect a cable or switch!
It is literally impossible to do without removing that bracket.
If anyone is having this problem . I just fixed mine easily… I did exactly what the video showed.. still had the drain.. come
To find out the the other door had the same issue!! I opened both doors and sprayed a generous amount of wd-40 inside the rear door latch on both sides - closed and opened the doors a few times - and the problem is now solved!! Good luck and thanks for this video
Thank you so much for taking the time to make this video. This was the most ambitious DIY car repair ive done and there is no way i do it without your help. You saved me a bunch of money. Wahoowa!
After watching this, I knew this was my problem from the intro, when the door closes then bumps a little bit open. It's getting towed to the shop tomorrow, then I will see what they say. Thank you for the info!
That one symptom pretty much confirms that something is wrong with the latch, in one form or another. I wish you luck!
Thank you for this! Best video I've seen on this repair, by far. It's not too long at all. Showing every step is key IMO, and watching it gives us a mental run-through of how it's going to go. Going to attempt this soon. Very well done, thanks again!
I had this same issue and it only happened in the winter. I replaced the mechanism instead of cleaning/lubricating, but a very thorough and helpful video.
Great instructions. Followed this yesterday to fix my van's intermittent door alarm and parasitic battery drain issues. Thank you!
Thanks for watching, glad it helped!
I agree 100%. Thank you for making this video. It’s not too long. It’s perfect. It was thorough. Saved me a lot of money.
Thanks for the video. I've been looking on how to repair this exact thing for about a month now. Part is incredibly expensive so i needed i cost effective way to repair. Again thank you
I have this problem in my 05 EX-L with 202k miles. I pull the fuse for the doors at night to avoid the battery dying...but I am so happy you made the video of how to fix the doors! Thank you so much! I'm going to work on mine this weekend. Unfortunately I also need center rollers on the opposite side, so I have my work cut out for me!
Now I know why my battery is going dead. Great video!
Thank you for your video and your generosity to help others with their problems with this issue.
My pleasure!
Third time watching one of these videos. I was originally searching for why I could not open the door at all. At 11:40 you explained my problem. Excellent thank you for the thorough and detailed explanation 👍 👍 👍 now I know what the problem is 😎
You are right about having to use oil or lithium grease. I did this to my doors a few years ago, but only used WD40 silicone spray and the problem came back. Now I have to do it again, so your video is super helpful. By the way, those hooks up top do come off, but they slide up and then pop out…I know because I broke mine and bought new ones.
Easy way to lube the inside of those puppies is to remove just one of the three latch mount bolts on the back outside of the door stick your lithium grease straw through the hole and spray inside. Replace that bolt and move onto the next bolt repeating the same step until you've done all three bolt holes. DO NOT REMOVE all three at the same time.
One at a time and replace each one individually.
This worked perfectly and saved a ton of unnecessary work and. anguish.
Did this last?
As you suggested, I also opted (for now, at least) to remove the 3 screws one at a time and spray WD-40 into the holes in order to try and lubricate and clean whatever mechanisms inside were gunked up. I also cleaned and WD-40 lubricated the latches / moving / closing mechanisms at both the front and back sides of the door. I will try to update my comment in a few months indicating if this is a permanent or temporary fix. (I suppose based on other comments, I may need to go back and use a spray lithium grease instead of just the WD-40.)
Interesting I just happened to buy Lithium grease spray can at Walmart today for like 6 bucks. I will try the 1 bolt at a time now instead of taking it apart just to see if it works. First I'm going to hook a multi meter up to confirm the issue
My '05 Odyssey had this exact problem and I used your video to fix it just a couple days ago. Thank you!
You are just amazing!!!! No other fitting words find to explain your genius teaching
Genius might be overselling it a bit, but thanks anyway😂
@@hanspoole😊
This is a great video you did a really good job! I found the micro switches online for only $7 each so I'm going to be repairing my doors and I will replace the switches anyway since my van is 18 years old with 340,000 miles! I prefer not to go through all that work and then not have my doors operate lol 😆 thank you again!
Where did you get your switches? Thanks
Some notes:
Do not remove the upper trim on a cold day; the trim plastic will be more brittle and can break when pulling out the plastic trim pegs.
My door handle did not have the metal circlip attached. I spent some time groping around for it before determining it was absent, and could just pull out the handle.
The inner door handle has three cables attached to it. If any one of these hangs up, the door will have problems closing. Since you have the panel off, you should squirt some lubricant into the front latch assembly. It was sort of tricky to do this, but I could bend the squirt straw through a hole in the sheetmetal and guide it in with my other hand reaching into the door. This helped free up the inner door handle cables.
I bought a used rear latch assembly for $100 off ebay. The little hinges and whatnot moved ok on the old one, after cleaning and oiling, but the plastic around the latch was shredded to bits.
Also, one step I had to do once I got the new one in was jump the closer motor to pull the door shut for the first time after reassembly. I don't know if the computer thought it was open, or what. No amount of prescribed resetting hacks (pulling fuses, disconnecting battery, etc) worked. I clamped alligator clips to the pins inside the socket he's detaching at 7:45 and ran the motor off a little 12 V charger.
Thank you, after 17 years, i didn't realize how gunked and dusty and dirty the insides were. It didn't really help that when i started noticing the problem i was putting a lot of lube in through the latch because that was the way i usually fixed the issue, not realizing there was much more inside that was causing the issue. I spent a good 2 hours trying to figure this out and cleaning but i guess you saved me a couple of hundred. mine is still not nearly as clean as your and i have a feeling another cleaning will be necessary at some point but once done once, I think it's going be pretty easy.
I’m glad my video was helpful for you! I completely agree that after you do it once, the next time is much easier. The first door I did was a learning experience, which is why I filmed myself doing the second one😆
Great video. Very thorough and well explained. Now to see if I can follow directions and fix this issue on my van!
Thanks for the video, Hans. This is exactly the problem I am having so I will give this a try. Your video is nice and detailed, so I feel like I can tackle the job.
John me too spokane area in Washington this a sum bitch
I want to commend you & thank you, you saved me a bunch of time ~ that one thing we cannot conserve, cheers!
I couldn’t agree more, you are very welcome!
I had a problem where my door acted as if it didn’t have power. Follow your steps to a T and it resolved the issue. Thank you! 🫡
Hans Poole thank you so much. You have a special place in my heart for sharing your knowledge with the world. THANK YOU SO MUCH!
Thank you, followed your instructions and my door now works
Yep, this is the video everybody with this fantastic Honda junker needs to see. Please become a manufacturing engineer, my dear friend. My tip: I put cargo springs in the back because of the sagging over the years, and it feels much better than stock.
@@hanspoole Yes, I was a little worried that the women might complain that the back of the van was too harsh, but it's fine. Feels real good, and it's not hard at all to do.
@@hanspoole I went back into my rockauto order history and the exact coil spring part is Lesjofors 4414240 for the pair.
Just did this with the help of your video, and it worked
This worked to fix the rear latch on our 2008 Honda Odyssey. Thank you!!
I'm glad it was helpful for you!
i actually extend out fuse 7 back up out to a switch and literally turn it off after locking the door
then prevent the drain after extensive dig into where the drain is
Thank you very much for the very helpful video! You save my time and money. You are awesome! 👍
Thank you, give me everything I needed to fix this! My door is work ing again! Thank you very much!
You’re saving me $800. Can’t wait to fix it this weekend.
I saw other videos, and you are First person I see take this issue straight, and fixed really fast
Great video. Going to tackle this today. Thanks for the thorough step by step video
How did it go? I'm going to tackle this in the next couple of days and I just need reassurance I can do this. 😳
Thanks for this video, was very helpful. Now I wait to see if that was my issue with the parasitic drain.
Awesome video! Stopped the parasitic drain. Hopefully another issue doesn't pop up right after lol
All the symptoms look to be the same with mine as well (2006). Dead battery in the morning, doors that dont seem to fully latch. Hoping this repair will solve my problems. Thanks for the very detailed video. I'll try to repair it sometime this next week and give a simple update on how it went.
Update: I did this repair to both of my sliding doors and It totally fixed the problem of my battery being dead every 12-20 hours. I measured the current draw before the repair and it was 400mA and after the repair it dropped to about 30mA. It took me about 2-3 hours for the first door and just over an hour for the second door. Thanks for the detailed video!!!
@@GarrettCrosgrove Where did you measure the draw?
@@jackjunk5495 directly on the battery. Disconnected it and put the amp meter inline with it.
@@GarrettCrosgrove Thanks. To isolate further, would you check the fuse connections?
@@jackjunk5495 Yeah pulling the 7.5amp fuse labeled "7 - BackUp" will also drop the battery amps from 400mA down to like 20mA. A quick fix for a battery draining until you can do the repair. I drove around for a week or so pulling the fuse everytime I parked it. Until I got around to fixing it using this video as a guide. That number 7 backup fuse also services the navigation system, door lights, power locks, dash lights when van is not running. and a few other things.
Very informative video! I have a 2004 odyssey and my side doors on both sides are messed up. Drivers side is really the culprit, so I will try my hand at this. Right now the drivers side back door won't even open so I have that to address too. Good video!
Thank you! Hopefully you’re able to get it all fixed up without too much trouble. The doors on my van quit working again last month, but it turns out that the micro switches are bad, so I won’t be able to get away with just relubing the mechanism. I’ll make a new video on my adventures once I find the time to actually do it within the next couple of weeks🤣
My situation was coupled with the symptom of a ticking/clicking noise only audible when near the fuse box.
It was a pretty fast tick and didn't seem like it was gonna stop anytime soon even with the key out!
I could literally feel the tick coming from the 7.5a fuse before i knew it was the one, pulling stopped the ticking!
That's what lead me here lol
The ticking has stopped and the door has no trouble closing anymore!
I did not take the door apart as you did, I used WD to clean that wire/cord and the grooves and loaded them up with a buttload of Lucas Marine grease (i chose this grease for weather protection and its high melting point, apparently the kind doesn't matter as much)
I also slapped on a silly amount of the marine grease into both latches at the front and back of both power doors.
I did the trunk for good measure, wasn't having a problem there but hopefully I won't either.
This worked good enough for me, literally no disassembly, i only wish I used a can of brake cleaner/contact cleaner with the long red tip to blow out the latches, there was dirt actually packed into that latch. I cringe looking back not doing it but I did it at break time at work lol (that's when i found my car died)
Is there a way to unplug it and so the power door would not work but the power draw would stop ?
Omg! My door was doing that but I couldn’t find any answers, thank you! Trying this soon!
Thanks a bunch for the video! Helped a lot
You're very welcome, I'm glad it helped!
@@hanspooleThanks for the upload. I have a 2000 with the same issue. Going to try it out. 👍
THANKS . MY 2005 rear sliding door wont open when the key is inserted into the ignition switch. I get a sliding door warning light but After I remove the key from the ignition switch, then remove and reinsert the 7.5A fuse; the rear door works great. IT system acts like a short somewhere when the key is inserted into the ignition switch. I will try cleaning the door latch like you suggested.
Great video 👍, did everything step by step, thanks 👍
Glad it helped!
thank you for your time and detailed explanation. while it doesn't look fun, I understand how to do it and why. great work!!!
Thx so much for this. I got the latch working. All fixed!
You're very welcome, I'm glad to hear you got it working!
Thank you so much for your informative video. I've been dealing with this for a few days and I'm eager to see how it turns out
Took my '05 Odyssey into the shop today thinking I had an alternator issue. They called me back a couple hours later and said that my battery and my alternator are good and that they picked up on a parasitic draw, likely for the back doors, so they removed Fuse 7 from the driver's side fuse box and the parasitic draw went away.
I know exactly which door it is too thankfully. It's the passenger side back door. We had opened it one day to get stuff out and then went to put the van in gear and it gave that buzzer sound as if the door was open. Opened and closed it a few different times to resolve the issue and it worked. However, the last time we had folks in the back of the van and it made the buzzer sound when we put it in gear, we just turned the power doors off so we wouldn't hear the buzzer. Now we know that we have to make sure the door gets all the way in so it doesn't drain everything instead of just turning off the power doors and calling it a day.
One downside about running around without that Fuse 7 is that now the interior auto lights don't come on when the door is open, I can't use the FOB to lock/unlock the vehicle, and the power locks don't function without the vehicle being turned on. The guy at the shop said that he wouldn't be able to fix the issue and that I would have to take it to a Honda dealership. I'm not skilled with vehicle repairs or anything, I'm more of an electronics (computers/phones/etc) guy, nor do I have the space to work on it myself, so I'll either see if I can find someone to replace that latch or see if getting the latch cleaned out will help prevent the parasitic draw.
Yup, that sounds exactly like what I experienced before cleaning up the latches. We got pretty use to shutting off the door switch every time we put the van in gear🤣.
I'm surprised you're able to get the door to close fully by just giving it a few tries. My guess is that it's just barely gunked up enough for it to not work sometimes, but not so much that it never works.
Good luck getting it fixed!
Thank you for this video! Well made! The comments are helpful. I think there's a good chance my van has a similar problem, and I'm hoping it has an easy fix.
We have a 2021 Honda Odyssey EX-L, which has had a parasitic drain since we bought it used 5 months ago. We just replaced the battery 2 days ago, but it still drains overnight.
The driver's side sliding door won't lock with either the remote or driver door controls.
A door ajar switch was replaced right before we bought it based on the Carfax report.
The fuel door won’t open by pressing on it, and we need to use the emergency pull cable from the back hatch to open it.
It has a DVD player that was added in 2021 but not from factory. At first we thought this might be the cause of the drain, but after watching your video we are wondering if the sliding door might be causing the drain and fuel door problem.
We're wondering if we should try what you are showing in the video with the sliding door, or if there's an easier fix by pulling a fuse to the door like mentioned in another comment. Not sure how different these issues would be in a 2021 compared to the van in your video. Any other ideas are welcome.
I don’t need the door to open & close, I just need the battery drain to stop. What fuse(s) can I remove to break the power connection and stop the drain?
@@hanspoole Very thorough video and follow up comments! I was on the verge of installing an in-cabin battery disconnect switch in my 2007 Odyssey, but your video gives me new hope to address a root cause! Thank you.
Hello Hans. Thank you for this YouTu be video. I was able to successfully get my power sliding door operating again on my 07 odyssey. However, now the problem is the window won’t come back up now that I have put it down. I wondered if any of your other viewers have had a similar issue and if so, do you know how they corrected it? The next thing I’m going to do is check all the fuses to see if that is the problem. Again, thanks for the video. I’ll find out in a couple of days whether it fixed the drain on the battery.
Thanks for your response . After inspecting the switch on the door, I found the harness the switch plugs into wasn’t making full
Contact . I was able to use electrical tape to hold things in place and the window gos up and down now. 😀 not sure how long this will last but the window is up for now. I may need a more permanent fix but this is good for now.
Thanks so much for making this! I’ve been dealing with this issue for a while now. I took my van to my mechanic, but we still haven’t been able to fully solve the problem. The best solution we’ve come up with so far is bypassing the electric doors, locks and interior lights to stop the parasitic drain, but that’s not ideal. I’d love to have everything functioning properly, including using the key fob to lock the doors.
I’m excited to try your method this weekend and see if it finally solves my issue. Everything you describe here, and in your other video, matches what I’ve been experiencing perfectly.
Do you have any tips on how to clean the tracks, and what product do you recommend for relubricating them after?
I've cleaned the tracks maybe one or two times (should probably do it more often) and from what I can remember, it's a lot easier if you remove that little trim piece that goes over the track. If you watch any video on how to replace the door rollers, it will be one of the first steps they show. I'd recommend using a white lithium spray grease.
Thank you for the amazing video. When I got my piece out of the door, I could not exactly tell what was wrong, if anything. I took the screw out that holds the little blue switch in place and tested the switch with a continuity tester - all was good (I was afraid this was the problem and I'd never be able to get just that switch). I also took the screw out of the switch so that I could push the switch aside or cover it while I sprayed some brake cleaner around that immediate area. I did this because I had white lithium grease on the door latch mechanism but regular amber grease everywhere else (window regulator). I felt it was better to leave the window section with its amber grease as is. The grease looked like it was doing it's job, but I really wanted to get all of the lithium grease off everything around the door latch area. With all of the lithium grease removed I could see everything working better. And by better I mean the slightest bit added to put enough pressure on the switch contact. The difference is very small to the eye but as you all know - that is what is needed, and you can verify this with a continuity tester. I then added some PB Blaster around the same area where the lithium grease was and cleaned off any that was running freely. Then I used your advice to use the 3 in 1 oil, but I wasn't exactly sure where the 3-in-1 was to be applied. I felt that the circular piece that rotates as the latch is activated and deactivated would be best served by some thicker oil there and I put a drop on the front side and back side. Hopefully that does the trick. Anyone else about to try to this job, I do think some brake cleaner gets the old crud out very well, just project the switch.
I discovered precisely the same thing when I took it apart for the first time. The mechanism seems to be moving ok at first glance, but upon further examination, you can see that the switches aren’t being activated fully. It’s the little things that count😉. Good point about using brake clean: while it works wonders removing grease, you’ve got to be careful around the delicate electronics.
BRILLIANT, great pace. Thank you..
my question is is the door open light on from this issue? he says ot thinks the door is open but mon dont show that on my dash unless i pop it open by hand
Thank you for your time and show us a nice video. Today i did what your video put back together it worked perfectly. Cheers
Thank the Lord above, you just saved me and my mother 1200 dollars plus on repairs for BOTH rear latches which were starting to go out, and the passenger side latch was even more locked up than the driver's side. I cannot thank you enough, and if you have a Ko-Fi, please give the link to it, because we would be happy to give you a donation as a thank-you.
I’m glad my video was so helpful for you! The satisfaction of knowing that my videos achieved my intended purpose is enough for me, and I am not familiar with Ko-Fi, so I respectfully decline your kind offer. Thank you for leaving a comment!
Anyone know what is acceptable standby current drain?
Can I just remove the power door fuse/relay? I just want manual doors.
If you want to get rid of the parasitic drain and just have manual doors by pulling a fuse, then fuse #7 in the driver’s side panel is the way to go. However, by pulling that fuse you will also disable other features such as locking the doors with the key fob and dome lights automatically turning on with open doors.
Can I unplug the door module behind the spare tire? Or door relays?
@hanspoole fuse #7 says Backup and it's a 7.5amp. Would that be the one ?
@@smithautomotive5029 Yes, that's the one. I've always wondered why it's labeled "backup" though🤔
I have the same exact problem and it’s very annoying while I’m driving and the map lights are coming on and off depending on when I turn right or left.🤦🏽♂️ I’m sure the price to have a professional fix this will run me a couple hundred, so thanks for the upload and information. I will attempt this myself and save myself some money. 💪🏽
Honda dealership wants to charge me around $3,500 to fix this exact same issue,but they’re saying they need to replace the “floor harness “
@@hanspoole As an update, i tried the DIY method and failed. The passenger side sliding door still reads as if it’s open. My lights still come on. However, the light switch for the map light located on the dash behind the right side of the steering wheel, has an on and off and also an option to never have any lights come on when a door is open. I keep it that way now.
This was one of the best how-to videos I've seen. Very thorough, but didn't waste time with chattiness. Question: Is there a latch in the front of the door as well as the back? I am almost done putting mine back together, but....I noticed that the mechanism that seems to latch on the front...isn't free flowing and snapping back up like the other side. So, I wonder if that could also be an issue with the parasitic draw. Thanks again.
I’m looking into replacing the switch for the mechanism but I’m confused. Are there two switches in there and is one NO and the other NC? (Normally opened/closed)
Looks like people are looking at this video recently as well, so here it is. Prior to putting the latch back, put water proof butyl tape along the TOP seam of the latch to close off the latch from moisture coming down through the door. Door panel is not water proof and there is drain hole at the bottom of the door to let water out. However, the water gets into the latch (later version of the latch had couple of foam tapes which helps but not totally water proof) and eats away at the lubrication and also this is worse in the winter because the lubrication gets hard AND the moisture inside the latch will freeze making things worse. In my experience, doing what he does will get you through couple of seasons but the issue will come back and so far, I had to swap out both of my latches with new OEM one (about $250 each) but since I had to swap out batteries 3 times because of the drain, you will save $$ from not having to swap out the battery. In a pinch, I found spray and pray method works for a month or 2. Just undo the 3 bolts from the back of the latch one at a time and spray with plenty of brake cleaner/degreaser using long straw followed by lithium grease (suitable for low temp) followed by manual opening and closing of the door 10-15 times will usually get the door gears unstuck.
That is a very good caveat to take note of! In fact, the microswitches on both door latches went bad on our van a couple of months ago (the latch mechanism still moves freely) and I'll need to solder in some new latches. In my case, I think what happened is that a lot of condensation formed on the inside of the door due to drastic temperature fluctuations. Haven't gotten around to putting in those new switches yet because life has been too busy, but I'll make sure to make a video when I finally get around to it 🤣
Good job very informative and very well done , i have the same power drain in my van i gotta fix soon as it stops raining ,
Very good video! Informative and well planned out! I like that you’re using a Benchmade as well! 👍🏻
I followed the steps and it worked. Thanks man
Thanks for the video great advice.. would you happen to know how to kill the sound when door is not shut ?.. my door is shutting but sometimes it doesn't and it's making an annoying beep sound
There's a couple ways to do that, easiest is to just turn off the sliding door switch on the dashboard to the left of the steering wheel. You can also remove the legendary fuse #7 in the driver's side fuse panel, but that disables more than just the doors.
@@hanspoole yeah I usually turn it off to manually use it .. but I thought maybe there was a way just to turn off the sound itself without touching the fuse
Any way you want to come over and fix this problem for me lol great video good job bud
He is insanely smart!!
Thank you for making this video. It helps me a lot
My 07 odyssey has the same symptons. Drains the battery after a couple days if not driving it. Blend door actuators going bad, Door sliders also bad. Everything else will go bad all at once. Cars a junk after 15 years. They should make cars simple again. Thanks for the video lesson.
Try lithium grease on the blend door nylon slides it worked for me. I agree with you these older Honda vans are overly complicated and troublesome
And manually move the blend door mechanism, lube the cable with wd40, that will help free it up. This is an easy fix
Hans, Thanx. That was a great video. I have a parasitic drain that I think is caused by the latch assembly switches. 06 Odessey.
I have a 2004 Odyssey with the same parasitic drain on battery. The #7 fuse on driver side is labelled "IG coil", 7.5w. I found the power slide fuse in panel under the hood. It's shows 30amp. If I pulled this fuse could it stop the battery drain? Or can I flip the switch inside so auto slide is OFF? Thank you for the detailed video.
I'm too lazy to take the door apart and just sprayed the heck out of the visible portion of the latch mechanism with lubricant. I'm encouraging my family to just NOT USE the driver side sliding door. This problem gets worse in the winter.
Edit: this actually worked all winter! Even using the door was totally fine. Definitely five my method a try before taking the door apart.
What lubricant did you used. W40 ?
@@frantisekbotko6846 Blaster brand silicone lubricant spray
Can anyone explain how he unplugs the black cable at 7:30?
I’ve been trying but it won’t come off.
The clip is towards the front of the van on the black connector. Push the top of the clip toward the connector, really firmly, and it will release at the bottom. I used a flathead on the connector to push it upwards simultaneously.
Don’t need to do this…. Just remove the top two 10mm bolts on the lock latch. Spray cleaner inside and lubrication. This sprays direction into the gummy area. Replace bolts, run it a few times and you’re done. Great video tho
So all you did was clean and lubricated mechanisms to fix an electrical draw ? No need to replace any micro switches ?
I was excited about finding this video so I took everything apart on my 07 and it looks like someone recently lubed everything and all the little mechanisms seem to be working fine. Any ideas on what to do from here? My van has all the symptoms you described at the beginning of the video