You want the leading edge to move against the way the tail is moving. If the tail is moving right the leading edge moves left and Vice versa to correct the tail.
Hello Ron when I get done with the tail setup the sliders is not returning to center position ... slider is moving freely... Is there anything else I can check or do I have a bad gyro... Thank you
Ron I got major probleagm. Maybe you can help me. I understand that tail is supposed to move in the opposite direction When acted on. Well that's not the case with me. FOR EXAMPLE: When I move the tail left the leading edge of the blade goes left too instead of right. Now obviously you'd be right to think you have to go in microbeastx gyro setup F and reverse gyro direction. Right? Well in my case it don't work. Ron what do I do old buddy? I am stumped. It's a brand new Microbeastx never crashed or broke?
hi Ron,got a question, I've got microbeast too,my question is I know you have version 3, cause of the 2 leds at start up,but how do they come to that conclusion with only 2 leds,weird
I have having problems getting the servocs programed in step G of your set-up process video. When the Microbeast is lit for programming the servos, two of the arms on the swash plate will jump, but one will always drop down. Why would this happen? The servos are Corona DS538HV and the transmitter is a Spektrum DX7S. Your video has been very helpful, but I am stuck at the step. Look forward to your help.
As soon as you go into step G and BEFORE touching the rudder stick, take the servo arms off and put them back on level. THEN adjust them one at a time using the steps in step G.
Step E Right push on Tx Stick makes tail blade LE go down. Step F Moving nose left (CCW) makes tail blade LE go down. Why Tex of tail blade LE moving left is confusing. or Best to use tex " tail blade LE moves down (left) "
You want the leading edge to move against the way the tail is moving. If the tail is moving right the leading edge moves left and Vice versa to correct the tail.
The Microbeast is not so scary anymore after watching!!
Many thanks for theses excellent presentations, thanks to you my Beast flies excellent!!!!!
I'm getting better thanks to your Videos..Thanks again...
Hello Ron, Is it posible to connect the yellow ESC conector to be used as a Governor, using a standard futaba receptor?
Great 🙏🏻
As with most electronics, once you understand the concept, it all becomes easier. Thanks for watching!
Hello Ron when I get done with the tail setup the sliders is not returning to center position ... slider is moving freely... Is there anything else I can check or do I have a bad gyro...
Thank you
Ron I got major probleagm. Maybe you can help me. I understand that tail is supposed to move in the opposite direction
When acted on. Well that's not the case with me.
FOR EXAMPLE: When I move the tail left the leading edge of the blade goes left too instead of right. Now obviously you'd be right to think you have to go in microbeastx gyro setup F and reverse gyro direction. Right?
Well in my case it don't work.
Ron what do I do old buddy?
I am stumped. It's a brand new
Microbeastx never crashed or broke?
hi Ron,got a question, I've got microbeast too,my question is I know you have version 3, cause of the 2 leds at start up,but how do they come to that conclusion with only 2 leds,weird
I have having problems getting the servocs programed in step G of your set-up process video. When the Microbeast is lit for programming the servos, two of the arms on the swash plate will jump, but one will always drop down. Why would this happen? The servos are Corona DS538HV and the transmitter is a Spektrum DX7S. Your video has been very helpful, but I am stuck at the step. Look forward to your help.
As soon as you go into step G and BEFORE touching the rudder stick, take the servo arms off and put them back on level. THEN adjust them one at a time using the steps in step G.
Step E
Right push on Tx Stick makes tail blade LE go down.
Step F
Moving nose left (CCW) makes tail blade LE go down.
Why
Tex of tail blade LE moving left is confusing.
or
Best to use tex " tail blade LE moves down (left) "
How do you reset it to defaults