ไม่สามารถเล่นวิดีโอนี้
ขออภัยในความไม่สะดวก
How to Install the 44 in Castlegate Ceiling Fan by Hampton Bay
ฝัง
- เผยแพร่เมื่อ 18 ส.ค. 2024
- This video covers the complete installation of the 44 in. Castlegate ceiling fan by Hampton Bay (model #52192). Use the links below to fast forward to each step of the process.
Safety info - 0:43
Parts Overview - 1:28
Removing the Mounting Bracket - 3:08
Installing the Mounting Bracket - 3:39
Routing the Wires / Attaching the Downrod - 4:27
Preparing the Remote - 6:10
Hanging the Fan - 7:25
Installing the Remote Receiver - 8:10
Wiring - 8:42
Attaching the Canopy - 10:03
Attaching the Decorative Ring - 10:49
Attaching the Blades - 11:08
Removing the LED Module - 12:12
Attaching the Light Kit Pan - 12:49
Attaching the LED Module - 13:48
Installing the Light Shade - 14:51
Operating the Remote - 15:19
Reverse Switch - 15:55
Installing the Remote Wall Cradle - 16:18
Congratulations! - 17:00
Watched the whole video and did step by step and worked out great! Thank you
that's awesome to hear! You're welcome!
You’re awesome clutch fr
That’s an awesome fan for a smaller space. Looks great!
It checks all the boxes! Cool design, nice amount of light for a small room and the dimming function is great!
it is great , I have one in my room, and one in the living room, I haven't used my air conditioner once this year.
New Subscriber and keep up the good work
This was very helpful. Thank you
You're welcome!
Hello, I installed the fan, your instructions helped a lot. However, even when I only want the light to be turned on, the fan spins around at the lowest speed (all three fan cycle levels light are off on the remote).
The lights on the remote only light up when the buttons are pushed. Make sure the fan is not set to low speed using the speed button to cycle through the speed settings. One push will light all of the lights (high speed), then another will be medium with 2 lights, then press again for low speed one light. Press one more time and no lights should come on. That will let you know that the fan speed is off. If the issue persists, we would suggest calling Hampton Bay customer service at 1-855-434-2678. Their team is pretty good at troubleshooting.
I can’t get the canopy off anymore after Installing
There is an alignment post that may be stopping the canopy from twisting off. The alignment post is shown at the 3:23 mark. You have to loosen the canopy screws enough so that there is enough room for the alignment post to exit that hole and allow the canopy to twist off.
How slow is the slow speed on this? We are looking for one that is slow as possible. We have one similar and on #1 it spins too fast for sleeping, it dries your eyes out haha. Anyone???
On low speed, the fan spins at a rate of 107 RPM.
@@ceilingfans101 many thanks!
How can I wire it to use a separate switch for the light and a separate one for the fan? I have both black and red HOT wires and two switches already installed.
Is one of the switches a speed control switch, or are they both just on/off switches?
@@ceilingfans101 both just on/off switches, but I have speed control switches I could install as well if those would work!
@@heatherdunn1050 We would recommend just wiring the receiver to one of the on/off switches. That would allow you to turn the fan/light on or off using the switch and retain complete control of the fan via the remote. If you wanted to use a speed switch, you would not be able to use the remote in conjunction with the switch. You could install without the remote and connect the fan's speed power wire (black) to the speed control and the light wire (blue) to the other switch. To do that, you would just need to cut the wire harness plug from the fan wires in order to separate the wires to be able to connect them to the switch wires.