How do I get the display to communicate with my battery? Do I need a special BMS or what? There is probably the possibility to read the temperature and remaining range in mAh. sorry for the annoyance :D
Display will not work with BMS . BMS needs Bluetooth and will work on your cellphone after you download the needed app for specific BMS then it will tell you the temperature, battery % and ah left to empty
@@Carlos-s4m that only depends on what controller you are running . In this video I am using controller you can't adjust anything ... latter videos I changed to Kelly controller and was able to push 250amps peak ..so the answer is you need controller to seriously adjust any noticeable settings
how far can you reduce the maximum speed on the display? and does it also apply to the throttle grip? that I only turn it down to 6 km / h so that it becomes legal
I've got a stealth bomber ebike with a 12,000 watt motor 150 amp controller 72 volts 38.8 amp hour battery. I couldn't figure out how to get the pedal assist to work but the motor was working fine off the throttle. So I did a factory reset on the display and haven't been able to get the bike back to normal. Before the display had the setting I could set it to throttle and pedal and now I don't see that in the menu. When I did the factory reset did the firmware change? I would like to put the latest firmware back on this and need help. Also I need help setting up the TFT settings in display. Right now when I pedal the bike goes too fast and the throttle doesn't work but I'm sure this was my fault because the factory reset. Could somebody
When you upload the firmware model you had all the settings will show up again , then you need to play with the numbers in the settings ... Always take a picture of current settings to avoid this problem
Hey I saw your video and I have the same LCD screen like yours you turn up the Current limit can you please explain what that really does because I need some help
So originally speed was set to 50 km I changed it to 150km , then I'm this screen you can only do 99 amps . You need to set it to 99amps whis gives the speed and torque to the bike . Long story short amps give you power to the bike.
This controller that came with the motor will not show the temperature , however my Kelly controller shows , so if you change the controller it will show temp
anyone can find out how to calculate Poles in motor→1~200 (=Poles quantity x Motor reduction rate? and why do I have to set the wheel size to 10 inches to have a speed not too far from the truth when I'm in 14 inches?
That's a nice looking display.👍👍
Thank you, that's the replacement I got from China.
@@TECHSUPPORTEBIKE Yea it looks good and pretty much does everything you want.Good buy for sure.
1801 on the password was a big help. Thanks
I hope you subscribed
Hi, do you know how to customize the speed of each of the assistance levels? Thank you
you need a display and ebike that supports kds protocol. Coswheel, Engwe, Anioki etc. they use yolin displays which allows you to do that.
How do I get the display to communicate with my battery? Do I need a special BMS or what? There is probably the possibility to read the temperature and remaining range in mAh. sorry for the annoyance :D
Display will not work with BMS . BMS needs Bluetooth and will work on your cellphone after you download the needed app for specific BMS then it will tell you the temperature, battery % and ah left to empty
Огромное вам спасибо!)
My display constantly shows 100 percent, even on a dead battery before turning off 100 percent! How can I solve this breakdown?
How do you make it have more torque
@@Carlos-s4m that only depends on what controller you are running . In this video I am using controller you can't adjust anything ... latter videos I changed to Kelly controller and was able to push 250amps peak ..so the answer is you need controller to seriously adjust any noticeable settings
looking very nice
how far can you reduce the maximum speed on the display? and does it also apply to the throttle grip? that I only turn it down to 6 km / h so that it becomes legal
With the throttle you can only lower the i sensitivity called delay in throttle response , as to limiting speed I went as low as 12mph for my son
@@TECHSUPPORTEBIKE ok is there a function in the menu to deactivate the throttle?
@@Uwe342 yes there is .
I've got a stealth bomber ebike with a 12,000 watt motor 150 amp controller 72 volts 38.8 amp hour battery. I couldn't figure out how to get the pedal assist to work but the motor was working fine off the throttle. So I did a factory reset on the display and haven't been able to get the bike back to normal. Before the display had the setting I could set it to throttle and pedal and now I don't see that in the menu. When I did the factory reset did the firmware change? I would like to put the latest firmware back on this and need help. Also I need help setting up the TFT settings in display. Right now when I pedal the bike goes too fast and the throttle doesn't work but I'm sure this was my fault because the factory reset. Could somebody
When you upload the firmware model you had all the settings will show up again , then you need to play with the numbers in the settings ... Always take a picture of current settings to avoid this problem
Hey I saw your video and I have the same LCD screen like yours you turn up the Current limit can you please explain what that really does because I need some help
So originally speed was set to 50 km I changed it to 150km , then I'm this screen you can only do 99 amps . You need to set it to 99amps whis gives the speed and torque to the bike . Long story short amps give you power to the bike.
Does it show motor temp?
This controller that came with the motor will not show the temperature , however my Kelly controller shows , so if you change the controller it will show temp
has yours got the usb out?
Yes it does.
Is amps set to battery amps ?
It sure was , back then it was a test battery 48v 50ah
@@TECHSUPPORTEBIKE awesome thanks so much I have ukc 1 on a 2000 watt nb power kit and could not get any help
@@tannermorris2133 so you got it working right 👍?
anyone can find out how to calculate Poles in motor→1~200 (=Poles quantity x Motor reduction rate? and why do I have to set the wheel size to 10 inches to have a speed not too far from the truth when I'm in 14 inches?
@@mickaellogeard2443 rim size plus tire size total size I would assume
Screens looking smart 👍
Lol smarter than me 🤣🤪
This company I'm dealing with has everything in black I don't get it.
Black fit all other colors
UKC-1 is not what it is.
It's a DELFAST controller.
Congratulations, You have something good.
You also get an instalike.
Definitely 😁 thank you for supporting the video with positive vibes 👍💯
Let's assume the seller doesn't give me the password for the advanced settings, what then?
Then you can get Kelly or Subvotan or any controller that you can do settings with wire or Bluetooth .....non of them need a display to work normally
@@TECHSUPPORTEBIKE Thanks :)
I just wanted to ask because I ordered a kit and I don't know if they will also give me the password
They are all the same password
@@TECHSUPPORTEBIKE It was 1801 - Thanks :)
Yeah that's what I used in the video ...all these set ups have same password FYI the lock for screen is all 000000
What is auto assist ?
There are few of them in a system , which one are you referring to , I do not use assist but the once are for pedal , speed, and display
Cruise control, turn it on on the menu then use throttle to get to speed you want and hold the minus button on the button pad and it’ll hold speed
I need help programming the perimeters
You want to change them or reset to it's original settings?