hall sensor and speed sensor? ive never actually used it but ive always been under the impression the white wire on the hall plug was a temp sensor wire.. good to know.
Hello. Thank you very much for your videos, they are quite clear and explanatory. They have been very helpful to me. Regarding the display, do you sell it? or could you leave a purchase link?
Thank you. Great video. I am very much interested in Fardriver controller. Will the display settings and everything ODO etc persist after battery removal or not? Planning to change my ebike controller from Savboton to Fardriver but the display situation has alway put me off.
Hello, I’m having trouble getting my anti theft function working with my nd 72450. I have the alarm and key fab installed but when I lock the hub motor spins freely. Do you have any information on how to get the hub motor to lock or be restricted when the alarm is activated
Can you also tell us more about the CAN control, Can you please tell me how we can connect this display with the BMS using the CAN Protocol, to check the available range? Thank you so much for this awesome video.
all you have to do is connect CAN H from the bms to CAN H on the display and CAN L from the bms to CAN L on the display just these 2 wires is all thats needed and then enable the CAN protocol in the bms app,some bms can only enable CAN protocol using the pc app
This must be why on the generic controllers I use lately with no display the 3 speed does not change motor speed. They are set to 0 at the factory. But I have older controllers that the 3 speed does work. Also the controller low voltage cut off on my 48/60/72 volt controller is set to 42 volts for a 48 v battery. I was using a 52v battery and the BMS must have no over discharge protection because it did not cut off till 42v. Not good.
Which pin in the board of controller for single line digital speedometer? Because i can't found the light blue wire on the my controller. And the wiring colour is very different with your controller.
Can you maybe help me. I recently buy one motorbike when the battery lithium 72v 30 Ah is connected, it always shows as 100% full with four bars on the speed display. However, the issue is that the bars do not decrease while driving; it remains at 100%. When I travel around 50 kilometers , the battery runs out but I only get the low battery signal with the icon appearing just about 30 seconds to a minute before it's completely depleted. This means I never see the battery level drop; it's either full or empty, making it very difficult to manage the autonomy, knowing when to recharge, especially since it could run out when far from a charging point.
Hello I have the same set up when i connect the battery to the controller im only reading 1.7v but the battery is reading 68.2v any ideas? Has the controller gone faulty??
@@samingham3077 You must make diagnosis on the battery... most probably you have some parallel cells undervolt or any bms cutted wire... check your battery
☆ HELP ☆ HELP ☆ why can I not connect to my 72450 FarDriver from the FarDriver app. Someone else is bound, guy says it won't let him connect to unbind. Please help
Thank you mate... unfortunately there is no any store out there.. you can buy it only from agents.. if you want u have one in stock first generation and 2 second generation with touch screen
Thank you for reviewing our display, we have many new styles now, feel free to review them!😁
Thank you ! I just purchased a fardriver and I'm just waiting for the Bluetooth adapter,
Great videos absolutely helpful in so many ways.
Thank you my friend... i will make many videos in this particular controller, so stay tuned..
Im from indonesia, i like your videos, i can to self learn from your video
Thank you sir good job 👍
hall sensor and speed sensor? ive never actually used it but ive always been under the impression the white wire on the hall plug was a temp sensor wire.. good to know.
Hello. Thank you very much for your videos, they are quite clear and explanatory. They have been very helpful to me. Regarding the display, do you sell it? or could you leave a purchase link?
Все четко обьяснил, дисплей отличный, жду продолжения! Спасибо )
Спасибо Алекс.. 👍
Where did you buy this display? Its possible to set mph instead of kmph?
Podrias dejarme el enlace de compra del display?
Thank you for this info and the series. You are very knowledgeable on a vague subject. Thank you again 😊
Thank you mate! 😁
Thank you. Great video.
I am very much interested in Fardriver controller. Will the display settings and everything ODO etc persist after battery removal or not? Planning to change my ebike controller from Savboton to Fardriver but the display situation has alway put me off.
Thanks for all your hard work.
Thank you man.. 👍
Do you know how to get the far driver into park so it shows on the screen
I want to buy a 72360 with the display shown in the video. Where can I purchase it?
Hello, I bought a 72680 fardriver, can you help me connect the cables well and program it?
Hello, I’m having trouble getting my anti theft function working with my nd 72450. I have the alarm and key fab installed but when I lock the hub motor spins freely. Do you have any information on how to get the hub motor to lock or be restricted when the alarm is activated
Hi , Can you please help me, my MTPA on the phone , shows Red and not green. please advice. thanks
Hello, how do I connect the S866 display to a controller without a standard 4/5 pin display port
Can you also tell us more about the CAN control,
Can you please tell me how we can connect this display with the BMS using the CAN Protocol, to check the available range?
Thank you so much for this awesome video.
all you have to do is connect CAN H from the bms to CAN H on the display and CAN L from the bms to CAN L on the display just these 2 wires is all thats needed and then enable the CAN protocol in the bms app,some bms can only enable CAN protocol using the pc app
@@angusmcgil thanks man..
Hi bro
How did you find the number of pole pairs, if we do not know the pole pair of the motor, how can we find out (without opening the motor)
Hi... i have video about that - How to Count Magnetic Poles of Hub Motor Without Open (Video)
@@EVCustoms bro thank you very much for all the information
This must be why on the generic controllers I use lately with no display the 3 speed does not change motor speed. They are set to 0 at the factory. But I have older controllers that the 3 speed does work. Also the controller low voltage cut off on my 48/60/72 volt controller is set to 42 volts for a 48 v battery. I was using a 52v battery and the BMS must have no over discharge protection because it did not cut off till 42v. Not good.
Which pin in the board of controller for single line digital speedometer?
Because i can't found the light blue wire on the my controller. And the wiring colour is very different with your controller.
how do you know to use the light blue wire from the controller to the screen?
😎i have some connections with the factory technician team..
@@EVCustoms ahh....that doesn't help those of us without those connections.
Can you maybe help me.
I recently buy one motorbike when the battery lithium 72v 30 Ah is connected, it always shows as 100% full with four bars on the speed display.
However, the issue is that the bars do not decrease while driving; it remains at 100%. When I travel around 50 kilometers , the battery runs out but I only get the low battery signal with the icon appearing just about 30 seconds to a minute before it's completely depleted. This means I never see the battery level drop; it's either full or empty, making it very difficult to manage the autonomy, knowing when to recharge, especially since it could run out when far from a charging point.
Can I use induction motor to drive my rear wheels.
Is the " CAN" light blue wire from the hall.?
No.. is alone from the controller side..
@EVCustoms thank you greatly. One last ? If I may.. my brake lever has a 3rd green signal wire? Do I need to connect it? If so. Where and why?
Will this work with a 5k watt motor?
Thank for your effort. But I have a question. Can I use Power Supply 72V 10A to test with Far-Driver instead of using Battery.
Yes of course..
@@EVCustoms How can I lock the Wheel of motor bike (motor lock)?
@@EVCustoms Need I limiting the current of Motor and Controller
Can you show circuit diagram for test board?
Very helpful, thank you
What lcd panel is that. May I have link
I can only use this controller on this display. Or I can use another controller....?
On fardriver and Votol controllers..
What kind of display is that?
Will this work woth bac8000
where can you buy such a display?
Any link to that display ? is it a SIAECOSYS variant ?? none seem to show the multimedia option like yours.
Hi.. i bring them straight from factory by agent, no is not Siaecosys variant, this one is universal screen for FarDriver and Votol controllers
Hello
I have the same set up when i connect the battery to the controller im only reading 1.7v but the battery is reading 68.2v any ideas? Has the controller gone faulty??
Hi.. your BMS is deactivated.. measure the battery voltage under load....
How do i activate it?
@@samingham3077 You must make diagnosis on the battery... most probably you have some parallel cells undervolt or any bms cutted wire... check your battery
☆ HELP ☆ HELP ☆
why can I not connect to my 72450 FarDriver from the FarDriver app. Someone else is bound, guy says it won't let him connect to unbind. Please help
hello could you please tell us the model number for this display so i dont get it wrong when i order thank you very much
Isn't there a tiny screen option aviable ? That thing is way to big
That's true... No yet, I will be great if this company produces more compact (smaller) screens..
Maybe some screen from monocicly( like begode, liperkim, inmotion). But they probably not cheap
My speed is not matching how do I calibrate it?
Fardriver with pedal assist connection?
How to custom booting logo screen?
Здравствуйте! Где такой дисплей можно купить. Есть ссылка?
Привет.. пока нету никаких ссылок на этот display, можно купить только через агентов
What display model?
Chaojie
Salve mi sa dire gentilmente come si fa a capire se un display è compatibile con qualsiasi centralina? Grazie
hi, you're great, I always follow you.
where can I buy this display?
Thank you mate... unfortunately there is no any store out there.. you can buy it only from agents.. if you want u have one in stock first generation and 2 second generation with touch screen
i need one for 52volt ub moter help pleezz
Hi
I'm from France
Would you consider zoom meetings so we can create an international ev enthusiasts group
Alangkah baiknya ketika anda juga membuat video versi votol controller
top video
Thank you my friend! 👍😀
@@EVCustoms every one of your videos is very good ... I learned a lot from your videos ... I wish you much success in your work
Thank you mate!
only800watts 52volt 24amps pleezz help ill buy a contler from u for this 52volt 24ampp mexst watts 1180 from 800watt moter
stop jabber jawing and hit that chinese m365 motor with the 390a phase current that controller claims. 👍👌⚡💥🔥☠️
This video is for learning purposes, you think i will ride this controller on 350w motor?
Why are you avoiding everyone.?? put a link for the display..
He said there's no store for the display..
Exactly... if someone need it, i have one spare (new) email me at ev-customs@hotmail.com
theres no store for the display ? this display is available for sell and have a 3dr generation that support car play lol
I think you should be more blunt and demanding of someone who gives us lots of quality free content 😂
Hi,what is the difference of model v1 and v3?thanks
Touch display and some extra themes
Super helpful, thank you